Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Normalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Opposed Flow Flame Spread in Normal, Enhanced and Reduced Gravity

Experimental and theoretical aspects of opposed-flow flame spread over solid fuels are presented with emphasis on the microgravity environments of spacecraft. For high opposing flow velocities, spread rate decreases with increasing velocity eventually leading to flame blowoff due to kinetic effects. At low opposing flow velocities, where diffusional effects are slowed and radiation becomes important, flame spread rate increases with increasing flow velocity. Extinction at low velocities is due to radiative effects. Modeling efforts that include radiation, both solid surface radiation and gas-phase radiation, predict qualitatively the experimental trends observed. Computationally, gas-phase radiation is conveniently included in solution of the conservation equations by employing a Plank mean absorption coefficient, a fraction of radiation that is fed back to the surface, and a shape function that describes the radiative flux distribution along the surface.

Altenkirch, Robert A.↗
NASA NTRS1991

Heat transfer in rotating serpentine passages with trips normal to the flow

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

Wagner, J. H.↗
NASA NTRS1992

On the normal modes of Laplace's tidal equations for zonal wavenumber zero

The characteristic differences between two different rotational modes of Laplace's tidal equations for wavenumber m = 0, called the K- and the S-modes, are compared in their energy ratio and structures. It is shown that the K-mode representation captures most of the observed zonal energy with a few terms, whereas the S-mode representation requires many terms. For small vertical scale components, the K-mode series converges faster than the S-mode series. Attention is also given to the differences between the energy spectra projected upon the K- and S-modes and the merits of each set as expansion functions for the zonal atmospheric motions.

Tanaka, H. L.↗
NASA NTRS1992

Vapor transport and crystal growth of GeSe under normal and high acceleration

Physical vapor transport experiments on GeSe in the presence of 2 atm xenon and for a nominal temperature difference of 600-500 C were performed under 1 g, 5 g, and 10 g acceleration conditions. Under high acceleration and destabilizing conditions, the GeSe crystals are generally larger than those under 1 g, stabilizing, and up to three orders of magnitude larger in surface area than those under 1 g, destabilizing conditions. The mass transport rates of the 5 g and 10 g destabilizing experiments are considerably greater than those of the 10 g, stabilizing, and 1 g experiments. The observed increase in mass flux (under destabilizing conditions) with acceleration is significantly greater than the anticipated dependence (mass flux proportional to g exp 1/4) for laminar, boundary-layer driven free convection. In view of the considerable convection under high acceleration, destabilizing conditions, the surface morphology and bulk crystallinity of the large crystal platelets are unexpectedly good.

Wiedemeier, H.↗
NASA NTRS1992

Distortion of a flat-plate boundary layer by free-stream vorticity normal to the plate

A nominally uniform flow over a semiinfinite flat plate is considered. The analysis shows how a small streamwise disturbance in the otherwise uniform flow ahead of the plate is amplified by leading-edge bluntness effects and eventually leads to a small-amplitude but nonlinear spanwise motion far downstream from the leading edge of the plate. This spanwise motion is then imposed on the viscous boundary-layer flow at the surface of the plate - causing an order-one change in its profile shape. This ultimately reduces the wall shear stress to zero, causing the boundary layer to undergo a localized separation, which may be characterized as a kind of bursting phenomenon that could be related to the turbulent bursts observed in some flat-plate boundary-layer experiments.

Goldstein, M. E.↗
NASA NTRS1992

Temperature dependence of the properties of DBR mirrors used in surface normal optoelectronic devices

The variation in the center wavelength of distributed Bragg reflectors used in optoelectronic devices, such as surface emitting lasers and Fabry-Perot modulators, is measured as the temperature of the mirrors changes over the range 25 C to 105 C. An analytic expression for the shift in center wavelength with temperature is presented. The mirrors measured are made of InP/InGaAsP, GaAs/AlAs, and Si/SiN(x). The linear shifts in center wavelength are 0.110 +/- 0.003 nm/C, 0.087 +/- 0.003 nm/C, and 0.067 +/- 0.007 nm/C for the InP/InGaAsP, GaAs/AlAs, and Si/SiN mirrors, respectively. Based on these data, the change in penetration depth with temperature is calculated.

Dudley, J. J.↗
NASA NTRS1991

Effect of interlaminar normal stresses on the uniaxial zero-to-tension fatigue behavior of graphite/epoxy tubes

Fatigue tests conducted with and without internal pressure have been found to possess approximately the same fatigue life as (+/-45)s graphite/epoxy tubes for zero-to-tension axial load-controlled conditions on an axial torsion servohydraulic apparatus. These tests therefore cannot be considered as confirmations of the suspected detrimental effect of interlaminar tensile stresses on the fatigue performance of thin-walled tubes. The addition of 90-deg plies on both the inside and the outside is found to significantly improve the tubes' static and fatigue strengths.

Krempl, Erhard↗
NASA NTRS1992

A bipolar population counter using wave pipelining to achieve 2.5 x normal clock frequency

Wave pipelining is a technique for pipelining digital systems that can increase clock frequency in practical circuits without increasing the number of storage elements. In wave pipelining, multiple coherent waves of data are sent through a block of combinational logic by applying new inputs faster than the delay through the logic. The throughput of a 63-b CML population counter was increased from 97 to 250 MHz using wave pipelining. The internal circuit is flowthrough combinational logic. Novel CAD methods have balanced all input-to-output paths to about the same delay. This allows multiple data waves to propagate in sequence when the circuit is clocked faster than its propagation delay.

Wong, Derek C.↗
NASA NTRS1992

Perturbation of a normal shock - A test case for unsteady Euler codes

Shock tracking capabilities of modern nonoscillatory schemes for solving the Euler equations are studied by comparing their solutions to solutions obtained using the method of characteristics on two test problems. Both test problems involve accelerating and decelerating shock motions. The schemes tested include first order upwind, second order SONIC-A, third order ENO, and third order TONIC-A. Results show that the second and higher order schemes give nearly identical shock trajectories that are closer to the characteristic solution than the first order upwind scheme. All schemes approach the characteristic solution upon mesh refinement.

Suresh, Ambady↗
NASA NTRS1991

A review of the kinetic detail required for accurate predictions of normal shock waves

Several aspects of the kinetic models used in the collision phase of Monte Carlo direct simulations have been studied. Accurate molecular velocity distribution function predictions require a significantly increased number of computational cells in one maximum slope shock thickness, compared to predictions of macroscopic properties. The shape of the highly repulsive portion of the interatomic potential for argon is not well modeled by conventional interatomic potentials; this portion of the potential controls high Mach number shock thickness predictions, indicating that the specification of the energetic repulsive portion of interatomic or intermolecular potentials must be chosen with care for correct modeling of nonequilibrium flows at high temperatures. It has been shown for inverse power potentials that the assumption of variable hard sphere scattering provides accurate predictions of the macroscopic properties in shock waves, by comparison with simulations in which differential scattering is employed in the collision phase. On the other hand, velocity distribution functions are not well predicted by the variable hard sphere scattering model for softer potentials at higher Mach numbers.

Muntz, E. P.↗
NASA NTRS1992

TRASYS form factor matrix normalization

A method has been developed for adjusting a TRASYS enclosure form factor matrix to unity. This approach is not limited to closed geometries, and in fact, it is primarily intended for use with open geometries. The purpose of this approach is to prevent optimistic form factors to space. In this method, nodal form factor sums are calculated within 0.05 of unity using TRASYS, although deviations as large as 0.10 may be acceptable, and then, a process is employed to distribute the difference amongst the nodes. A specific example has been analyzed with this method, and a comparison was performed with a standard approach for calculating radiation conductors. In this comparison, hot and cold case temperatures were determined. Exterior nodes exhibited temperature differences as large as 7 C and 3 C for the hot and cold cases, respectively when compared with the standard approach, while interior nodes demonstrated temperature differences from 0 C to 5 C. These results indicate that temperature predictions can be artificially biased if the form factor computation error is lumped into the individual form factors to space.

Tsuyuki, Glenn T.↗
NASA NTRS1993

Soot formation and radiation in turbulent jet diffusion flames under normal and reduced gravity conditions

Most practical combustion processes, as well as fires and explosions, exhibit some characteristics of turbulent diffusion flames. For hydrocarbon fuels, the presence of soot particles significantly increases the level of radiative heat transfer from flames. In some cases, flame radiation can reach up to 75 percent of the heat release by combustion. Laminar diffusion flame results show that radiation becomes stronger under reduced gravity conditions. Therefore, detailed soot formation and radiation must be included in the flame structure analysis. A study of sooting turbulent diffusion flames under reduced-gravity conditions will not only provide necessary information for such practical issues as spacecraft fire safety, but also develop better understanding of fundamentals for diffusion combustion. In this paper, a summary of the work to date and of future plans is reported.

Ku, Jerry C.↗
NASA NTRS1993

A note on the distortion of a flat-plate boundary layer by free-stream vorticity normal to the plate

The purpose of this note is to construct a local solution that eliminates a residual velocity discontinuity in the inviscid portion of a solution obtained in a recent paper by Goldstein, Leib and Cowley (1992). This result is of importance because it shows that the solution obtained in that paper is entirely non-singular outside the viscous wall boundary layer and that any singularity in the problem will have to arise in the usual way through a breakdown in the viscous boundary layer.

Goldstein, M. E.↗
NASA NTRS1992

X-ray photoelectron spectroscopy characterization of a nonsuperconducting Y-Ba-Cu-O superconductor-normal-metal-superconductor barrier material

A film of a novel nonsuperconducting Y-Ba-Cu-O (YBCO) barrier material was grown using conditions similar to those reported by Agostinelli et al. (1991) for forming a cubic semiconducting (c-YBCO) phase, and the material was characterized using X-ray photoelectron spectroscopy (XPS). A comparison of the XPS spectra of this material to those obtained from the orthorhombic and tetragonal phases of YBCO (o-YBCO and t-YBCO, respectively) showed that the barrier material had spectral characteristics different from those of o-YBCO and t-YBCO, particularly in the O 1s region. Features associated with the Cu-O chain and surface-reconstructed Cu-O planes were absent, consistent with expectations for the simple perovskite crystal structure of c-YBCO proposed by Agostinelli et al.

Vasquez, R. P.↗
NASA NTRS1936

Further measurements of normal accelerations on racing airplanes

The work of collecting acceleration data for racing airplanes during races, started in January 1934, has been continued by obtaining similar data in the airplanes winning first and second places in the 1935 Thompson Trophy Race. Records were taken in the Howard Racer "Mr. Mulligan" and in the Wittman D-12 Racer. The maximum positive accelerations were generally smaller than those recorded in other airplanes during earlier races; the maximum in the Howard Racer was 2.8 g, and one value of 4.25 g was obtained in the Wittman Racer. Minimum values were as low as -0.55 g in the Howard Racer and 0.3 g in the Wittman Racer.

Scudder, N F↗