Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Geologic data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

The future of subsurface monitoring: AEC’s breakthroughs in CCS technology

Carbon capture and storage (CCS) has emerged as a key solution in the fight against climate change. However, for CCS to succeed, it is crucial to ensure that the sequestered CO2 stays safely trapped underground. The U.S. Department of Energy (DOE) has emphasized the need for advancements in subsurface monitoring, measurement, reporting, and verification. Aside from caprock integrity failure, the other primary failure points usually involve defective cement in the casing annulus of wellbores or plugged and abandoned wells. In addition, many energy producers (e.g., oil and gas, geothermal) and storage and disposal operators (e.g., H2 and water) must deal with the same issue. Poorly placed or degraded cement can create pathways for gas or fluid to escape from casing annuli and in plugged and abandoned or orphan wells, posing environmental risks. Yet, a reliable and cost-effective way to monitor cement and well integrity over multiple decades is still unavailable. Traditional geophysical methods like 4D seismic imaging and surface-based electromagnetic monitoring lack the resolution and accuracy for detecting these types of failures (Vasco et al., 2022; Fawad and Mondol, 2021). Wireline logging is expensive to run continuously and is obtrusive to the operation. While fiber optics can potentially be a solution, its bulkiness can significantly compromise the cement's integrity. To address these challenges, the Advanced Energy Consortium (AEC) at The University of Texas at Austin’s Bureau of Economic Geology (the Bureau) has been pioneering research in subsurface monitoring using its portfolio of distributed autonomous microfabricated sensors for harsh subsurface environments since 2008. A class of these microsensors [System on a Chip (SoC)] can be mixed in cement and permanently placed without compromising the cement column; the sensors would then communicate with each other or a data acquisition (DAQ) master node. Another class of the AEC microsensors can be fully autonomous, with rechargeable micro-batteries capable of exceeding 100°C, flash memory, and, currently, a pressure and temperature sensor. They are designed to circulate in mud, geothermal fluids, U-loops, or pipelines. They can log data into memory and are unobtrusive to operations. Our team has been working on a multi-year DOE-funded project (DE-FE0031856)—supported by $2.95M in federal funding and $0.75M in cost-matching from the AEC—to demonstrate SoC sensor utility for CO2 leakage monitoring in CCS applications. This multi-institutional collaboration developed a novel sensing architecture utilizing radiofrequency (RF) microsensors embedded within the cement sheath. These sensors detect CO2 migration and are interrogated via a Smart Casing Collar (SCC).

58 GEOSCIENCES↗

Solubility constants of hydroxyl sodalite at elevated temperatures evaluated from hydrothermal experiments: Applications to nuclear waste isolation

In this study, solubility constants of hydroxyl sodalite (ideal formula, Na 8 [Al 6 Si 6 O 24 ][OH] 2 ·3H 2 O) from 25°C to 100°C are obtained by applying a high temperature Al—Si Pitzer model to evaluate solubility data on hydroxyl sodalite in high ionic strength solutions at elevated temperatures. A validation test comparing model-independent experimental data to model predictions demonstrates that the solubility values produced by the model are in excellent agreement with the experimental data. In addition, the equilibrium constants obtained in this study have a wide range of applications, including synthesis of hydroxyl sodalite, de-silication in the Bayer process for extraction of alumina, and the performance of proposed sodalite waste forms in geological repositories in various lithologies including salt formations. The thermodynamic calculations based on the equilibrium constants obtained in this work indicate that the solubility products in terms of m ΣAl ×m ΣSi for hydroxyl sodalite are very low (e.g., ~10 -13 [mol·kg -1 ] 2 at 100°C) in brines characteristic of salt formations, implying that sodalite waste forms would perform very well in repositories located in salt formations. Finally, the information regarding the solubility behavior of hydroxyl sodalite obtained in this study provides guidance to investigate the performance of other pure end-members of sodalite such as chloride- and iodide-sodalite, which may be of interest for geological repositories in various media.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling of CBM production, CO2 injection, and tracer movement at a field CO2 sequestration site

Sequestration of carbon dioxide in unmineable coal seams is a potential technology mainly because of the potential for simultaneous enhanced coalbed methane production (ECBM). Several pilot tests have been performed around the globe leading to mixed results. Numerous modeling efforts have been carried out successfully to model methane production and carbon dioxide (CO{sub 2}) injection. Sensitivity analyses and history matching along with several optimization tools were used to estimate reservoir properties and to investigate reservoir performance. Geological and geophysical techniques have also been used to characterize field sequestration sites and to inspect reservoir heterogeneity. The fate and movement of injected CO{sub 2} can be determined by using several monitoring techniques. Monitoring of perfluorocarbon (PFC) tracers is one of these monitoring technologies. As a part of this monitoring technique, a small fraction of a traceable fluid is added to the injection wellhead along with the CO{sub 2} stream at different times to monitor the timing and location of the breakthrough in nearby monitoring wells or offset production wells. A reservoir modeling study was performed to simulate a pilot sequestration site located in the San Juan coal basin of northern New Mexico. Several unknown reservoir properties at the field site were estimated by modeling the coal seam as a dual porosity formation and by history matching the methane production and CO{sub 2} injection. In addition to reservoir modeling of methane production and CO{sub 2} injection, tracer injection was modeled. Tracers serve as a surrogate for determining potential leakage of CO{sub 2}. The tracer was modeled as a non-reactive gas and was injected into the reservoir as a mixture along with CO{sub 2}. Geologic and geometric details of the field site, numerical modeling details of methane production, CO{sub 2} injection, and tracer injection are presented in this paper. Moreover, the numerical predictions of the tracer arrival times were compared with the measured field data. Results show that tracer modeling is useful in investigating movement of injected CO{sub 2} into the coal seam at the field site. Also, such new modeling techniques can be utilized to determine potential leakage pathways, and to investigate reservoir anisotropy and heterogeneity.

Reservoir modeling↗

CO 2 storage and potential fault instability in the St. Lawrence Lowlands sedimentary basin (Quebec, Canada): Insights from coupled reservoir-geomechanical modeling

In this paper, coupled reservoir-geomechanical (TOUGH-FLAC) modeling is applied for the first time to the St. Lawrence Lowlands region to evaluate the potential for shear failure along pre-existing high-angle normal faults, as well as the potential for tensile failure in the caprock units (Utica Shale and Lorraine Group). This activity is part of a general assessment of the potential for safe CO 2 injection into a sandstone reservoir (the Covey Hill Formation) within an Early Paleozoic sedimentary basin. Field and subsurface data are used to estimate the sealing properties of two reservoir-bounding faults (Yamaska and Champlain faults). The spatial variations in fluid pressure, effective minimum horizontal stress, and shear strain are calculated for different injection rates, using a simplified 2D geological model of the Becancour area, located ~110 km southwest of Quebec City. The simulation results show that initial fault permeability affects the timing, localization, rate, and length of fault shear slip. Contrary to the conventional view, our results suggest that shear failure may start earlier for a permeable fault than for a sealing fault, depending on the site-specific geologic setting. In simulations of a permeable fault, shear slip is nucleated along a 60 m long fault segment in a thin and brittle caprock unit (Utica Shale) trapped below a thicker and more ductile caprock unit (Lorraine Group) – and then subsequently progresses up to the surface. In the case of a sealing fault, shear failure occurs later in time and is localized along a fault segment (300 m) below the caprock units. The presence of the inclined low-permeable Yamaska Fault close to the injection well causes asymmetric fluid-pressure buildup and lateral migration of the CO 2 plume away from the fault, reducing the overall risk of CO 2 leakage along faults. Finally, fluid-pressure-induced tensile fracturing occurs only under extremely high injection rates and is localized below the caprock units, which remain intact, preventing upward CO 2 migration.

58 GEOSCIENCES↗

Hydrogeological Model Selection Among Complex Spatial Priors

Hydrogeological field studies rely often on a single conceptual representation of the subsurface. This is problematic since the impact of a poorly chosen conceptual model on predictions might be significantly larger than the one caused by parameter uncertainty. Furthermore, conceptual models often need to incorporate geological concepts and patterns in order to provide meaningful uncertainty quantification and predictions. Consequently, several geologically realistic conceptual models should ideally be considered and evaluated in terms of their relative merits. Here, we propose a full Bayesian methodology based on Markov chain Monte Carlo to enable model selection among 2-D conceptual models that are sampled using training images and concepts from multiple-point statistics. More precisely, power posteriors for the different conceptual subsurface models are sampled using sequential geostatistical resampling and Graph Cuts. To demonstrate the methodology, we compare and rank five alternative conceptual geological models that have been proposed in the literature to describe aquifer heterogeneity at the MAcroDispersion Experiment site in Mississippi, USA. We consider a small-scale tracer test for which the spatial distribution of hydraulic conductivity impacts multilevel solute concentration data observed along a 2-D transect. The thermodynamic integration and the stepping-stone sampling methods were used to compute the evidence and associated Bayes factors using the computed power posteriors. We find that both methods are compatible with multiple-point statistics-based inversions and provide a consistent ranking of the competing conceptual models considered.

58 GEOSCIENCES↗

Development of Improved Caprock Integrity and Risk Assessment Techniques. Final report for period Oct. 1, 2012 - Sept. 30, 2014

GeoMechanics Technologies has completed a geomechanical caprock integrity analysis and risk assessment study funded through the US Department of Energy. The project included: a detailed review of historical caprock integrity problems experienced in the natural gas storage industry; a theoretical description and documentation of caprock integrity issues; advanced coupled transport flow modelling and geomechanical simulation of three large-scale potential geologic sequestration sites to estimate geomechanical effects from CO₂ injection; development of a quantitative risk and decision analysis tool to assess caprock integrity risks; and, ultimately the development of recommendations and guidelines for caprock characterization and CO₂ injection operating practices. Historical data from gas storage operations and CO₂ sequestration projects suggest that leakage and containment incident risks are on the order of 10 -1 to 10 -2 , which is higher risk than some previous studies have suggested for CO₂. Geomechanical analysis, as described herein, can be applied to quantify risks and to provide operating guidelines to reduce risks. The risk assessment tool developed for this project has been applied to five areas: The Wilmington Graben offshore Southern California, Kevin Dome in Montana, the Louden Field in Illinois, the Sleipner CO₂ sequestration operation in the North Sea, and the In Salah CO₂ sequestration operation in North Africa. Of these five, the Wilmington Graben area represents the highest relative risk while the Kevin Dome area represents the lowest relative risk.

58 GEOSCIENCES↗

Well-Log Derived Geomechanical Analysis of Microseismicity in the Mt. Simon Saline Aquifers (Illinois Basin - Decatur Project)

The Illinois Basin Decatur Project (IBDP) successfully demonstrated the safe geologic storage of carbon dioxide at a commercial scale. Within the IBDP project three deep wells (injection (CCS1), monitoring (VW1), geophysical (GM1)) were competed and geophysical logs were recorded. During injection and post-injection periods microseismic monitoring was conducted to create a miscoseismic catalog. The correlations between microseimic attributes and geomechanical well logs define major geomechanical drivers of microseismic expression to understand a reservoir response to CO2 injection in geological context. Utilizing standard sonic and density well logs, the dynamic elastic moduli were calculated and employed to correlate with microseismic pseudo-logs. A multi-dimensional Mu-rho and Lambda-rho (MRLR) hyperdimensional plots display of meaningful data and uncovered subtle relationships between elastic properties of sandstones and the seismological attributes of recorded microseismicity.

Myshakin, Evgeniy↗

National Brackish Groundwater Assessment 2017

Brackish groundwater (BGW), defined for this assessment as having a dissolved-solids concentration between 1,000 and 10,000 milligrams per liter, is an unconventional source of water that may offer a partial solution to current (2016) and future water challenges. In support of the National Water Census, the U.S. Geological Survey has completed a BGW assessment to gain a better understanding of the occurrence and characteristics of BGW resources of the United States as an alternative source of water. Analyses completed as part of this assessment relied on previously collected data from multiple sources, and no new data were collected. One of the most important contributions of this assessment was the creation of a database containing chemical data and aquifer information for the known quantities of BGW in the United States. Data were compiled from single publications to large datasets and from local studies to national assessments, and includes chemical data on the concentrations of dissolved solids, major ions, trace elements, nutrients, radionuclides, and physical properties of the resource (pH, temperature, specific conductance). This database represents data from a compilation of water-quality samples from 100,000+ (major-ions data) to 300,000+ (dissolved-solids data) groundwater wells across the continental U.S., Alaska, Hawaii, Puerto Rico, the U.S. Virgin Islands, Guam, and American Samoa. The data are published here as an ESRI geodatabase with a point feature class and associated attribute table, and also as non-proprietary comma-separated value table. It was not possible to compile all data available for the Nation, and data selected for this investigation were mostly limited to larger datasets that were available in a digital format.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Hydrothermal Exploration Best Practices and Geothermal Knowledge Exchange on OpenEI

Though exploring for hydrothermal resources is not new, advances in exploration technologies and the pursuit of less visible resources have created a need to outline exploration best practices. This multi-year study outlines 21 geothermal exploration regions in the Western United States. These regions were developed based on the U.S. Geological Survey (USGS) physiographic regions, then adjustedto fit geothermal parameters such as differences in geologic regime, structure, heat source, surface effects (weather, vegetation patterns, groundwater flow), and other relevant factors. Literature searches were conducted in each of these 21 regions for the application of field reconnaissance, geochemical, geophysical and remote sensing techniques. At this time, data from more than 250 referenceshave been cataloged in U.S. Department of Energy's (DOE) OpenEnergy Information (OpenEI, http://en.openei.org) website, which allows industry to access data information and run analyses on specific data attributes. The platform also allows updates, edits, and additions from the public so that the dataset can be expanded as industry's knowledge grows. In addition to the literature survey,interviews were conducted with exploration experts with both geothermal and oil-and-gas industry experience to identify the exploration challenges and best practices for the exploration regions. This paper defines and describes the geothermal regions developed for this study, describes how exploration techniques contribute to hydrothermal analyses (structural, petrologic, temperature, andhydrologic), and defines the exploration hurdles and best practices for each region. The results of the study and accompanying data sets on OpenEI will be available through the National Geothermal Data System.

15 GEOTHERMAL ENERGY↗

Final Scientific/Technical Report of Gas Hydrate Dynamics on the Alaskan Beaufort Continental Slope: Modeling and Field Characterization

Methane Hydrates, a solid form of methane and water, exist at high pressures and low temperatures, occurs on every continental margin on Earth, represents one of the largest reservoirs of carbon on the planet, and, if destabilized, may play an important role in both slope stability and climate change. For decades, researchers have studied methane hydrates with the hope of determining if methane hydrates are destabilizing, and if so, how this destabilization might impact slope stability and ocean/atmosphere carbon budgets. In the past ~5 years, it has become well established that the upper “feather-edge” of methane hydrate stability (intermediate water depths of ~200-500 meters below sea level) represents an important frontier for methane hydrates stability research, as this zone is most susceptible to destabilization due to minor fluctuations in ocean temperature in space and time. The Arctic Ocean—one of the fastest warming regions on Earth—is perhaps the best place to study possible changes to methane hydrate stability due to ocean warming. To address the stability of methane hydrates at intermediate ocean depths, Southern Methodist University in partnership with Oregon State University and The United State Geological Survey at Woods Hole began investigating methane hydrate stability in intermediate water depths below both the US Beaufort Sea and the Atlantic Margin, from 2012-2017. The work was funded by the Department of Energy’s (DOE) National Energy Technology Laboratory (NETL). The key goal of the SMU component of this study was to collect the first ever heat flow data in the Beaufort Sea and compare measured shallow (probe-based1) heat flow values with deeper (BSR-derived2) heat flow values, and from this, determine whether hydrates were in thermal equilibrium. In September 2016, SMU/OSU collected the first ever heat flow measurements in the US Beaufort Sea. Despite poor weather and rough seas, the cruise was a success, with 116 heat flow measurements acquired across the margin, spanning 4 transects separated by more than 400 km. Useable heat flow data exists for 97% (113) of probe heat flow measurements, revealing a clear picture of regional heat flow across the basin. During the past 8 months since the cruise, SMU researchers have processed the heat flow and thermal conductivity measurements and compared results to deeper heat flow estimates obtained from seismic data. The analysis reveals clear, consistent trends: All probe heat flow measurements in depths greater than 800 mbsl are consistent with BSR-derived values; heat flow measurements obtained in water depths between ~250-750 mbsl are systematically lower than those estimated from BSRs; and heat flow estimates in water depths shallower than ~250 mbsl are systematically warmer than deeper estimates. The consistency between shallow (probe) and deep (BSR) heat flow measurements at depths greater than ~750 m where ocean temperature changes are minimal supports the premise that the hydrates consist primarily of methane and represent a valuable tool for estimating heat flow. The anomalous cooling trend observed in the upper 250 m is consistent with expected seasonal effects observed in shallow ocean buoy measurements in the arctic, when cold, less dense melting sea ice cools the upper 200 m of the ocean during the summer as ice melting occurs. The discrepancy in heat flow at intermediate water depths is best explained via recent intermediate ocean temperature warming, where long-term (annual or longer) warming intermediate ocean bottom waters result in an anomalously low heat flow in shallow heat flow measurements. Using the characteristic 1D time-length scale for diffusion, we estimate that ocean temperature warming began no later than ~1200 years ago but arguably much more recently as results are limited by seismic resolution. More importantly, our analysis indicates methane hydrate is destabilizing not only in the upper feather edge (200-500 mbsl) but at depths as great as 750 mbsl. The intermediate ocean warming rate supports previous studies suggesting geologically rapid warming (>0.1 deg C/decade) at intermediate ocean depths in the Beaufort Sea. Assuming no further changes or additional warming, our analysis indicates methane hydrates will destabilize at seafloor depths shallower than 750 mbsl in the Beaufort Sea within the next ~3000 years. 1 Probe outfitted with sensors inserted into the seafloor sediment 2 Bottom-simulating reflector (BSR) seismic data indicates presence of hydrate deposits

58 GEOSCIENCES↗

Quadri-joint inversion: Method and application to the Big Sky 9C 3D data set in northern Montana

The Kevin Dome [Formula: see text] storage project, located in northern Montana, attempted to characterize the Duperow Formation as a potential long-term storage zone for injected [Formula: see text]. A multicomponent (9C) seismic survey was acquired for the Big Sky Carbon Sequestration Partnership over a portion of the Kevin Dome using P- and S-wave sources. Prestack migrated PP, PS, SH, and SV data sets were generated. We then applied several stratigraphic inversion workflows using one or several kinds of seismic wavefield at the same time resulting in joint inversions of each data set. The aim of our study is to demonstrate the benefits of doing quadri-joint inversion of PP-, PS-, SH-, and SV-wavefields for the recovery of the elastic earth parameters, especially the S-wave impedance and density. These are crucial parameters because they can help determine lithology and porefill in the reservoir characterization workflow. Because the inversion workflow always uses the original seismic data recorded in its own time domain, it is necessary to compute registration laws between PP-PS-, PP-SH-, and PP-SV-wavefields using a time shift computation procedure (warping) based on inverted S-wave impedances from inversion of a single wavefield. This generated a significant improvement over methods that rely on attempting to match trace waveforms that may have a different phase, frequency content, and polarity. Finally, we wanted to investigate the reliability of the quadri-joint inversion results in the Bakken/Banff Formations, which have less lateral geologic variation than the underlying Duperow target. This interval shares many of the geophysical characterization challenges common to shale reservoirs in other North American basins. We computed geomechanical parameters, such as Poisson’s ratio and Young’s modulus, which are a proxy for brittleness. Comparison of these results with independent laboratory measurements in the Bakken interval demonstrates the superiority of the quadri-joint inversion method to the traditional inversion using P-wave data only.

Geochemistry & Geophysics↗

Data for The Value of Reversible Carbon Storage in a Zero-Emissions World

Atmospheric carbon dioxide removal (CDR) is required to stabilize global temperature. CDR can be achieved via ecosystem-based approaches that are cost-effective but reversible (e.g., soil and forest management) or by more durable but expensive approaches (e.g., direct air capture coupled with geologic storage). Here, we examine trade-offs between these approaches, focusing on timing, climate impacts, and cost. We simulated reversible carbon accrual for a range of CDR contract structures using a general minimalist model of ecosystem carbon cycling, and parameterized it to simulate US agricultural soil management─specifically cover cropping─as a case study. We then quantified the resulting impact on atmospheric carbon and global temperature using a climate model emulator. We find that maintaining a patchwork of reversible CDR projects by replacing lapsed projects with new projects can reduce warming by 22–195 μ°C in 2100 and that the magnitude of this cooling effect depends on how effectively the patchwork is maintained. Long-term maintenance of reversible CDR projects requires institutional stability that cannot be guaranteed over multiple decades. Consequently, effective CDR ultimately requires replacing reversible projects with durable projects. To address this problem, we modeled the cost of replacing reversible agricultural soil CDR with geologic CDR. We found that using reversible CDR as a bridge to durable CDR is potentially more cost-effective as a global cooling strategy (0.20–0.81 billion USD per μ°C avoided) than perpetual maintenance of reversible CDR (0.32–1.31 billion USD per μ°C avoided) or an immediate transition to durable CDR (1.37–2.19 billion USD per μ°C avoided). However, we emphasize that institutional commitments to maintain reversible CDR projects cannot be guaranteed. Reliance on reversible CDR as a bridge to durable CDR therefore carries an unknown amount of risk and will only function if efforts to maintain reversible CDR are robust.

Carbon↗

Bayesian Approach to Estimation of Water Table Elevations Using Historical Rasters as Prior Information 2019 - 20430

In cases of complex but only partially known geology and a lack of spatial control in observation well locations, water table elevation estimation is very challenging. In some cases, auxiliary information, such as observations of the movement of tracers, operation of injection and extraction wells, and calibration of groundwater models against the historical elevation data, can be combined with expert judgement to estimate flow directions in areas of sparse data and to aid in the production of more reliable contour maps (and associated rasters) than could be produced by relying on sparse well elevation data alone. Given a historical sequence of these raster maps, the question arises how to automate, to the extent possible, the process of producing new raster maps to reflect data from previous times, the current data and the operation of expert judgement. One solution is to adopt a Bayesian point of view and to regard the historical well elevation data, auxiliary information and historical raster maps as prior information. The well elevations for water table wells, as well as those for injection/extraction wells and the data associated with other relevant variables, can be viewed as predictors for the raster surface. From this prior information, we can, conditional on the values of these predictors for a new time period, compute an expected value map and a standard deviation map for the new raster. These then can be taken to specify a prior predictive distribution for the pixels in the new raster map. Then we condition the pixels, corresponding to water level observation wells within the raster, on the observed values in those wells (which in general will differ from the regression estimate) for the new time period. Given the smoothness of the water table surface, we then smooth the surface of deviations from the mean surface, based on the variograms of the historical rasters, and add this smoothed surface to the regression mean surface. The error structure of the produced raster map is defined by the regression error structure and the error due to smoothing based on the estimated variograms. This methodology has been developed and is being further refined for groundwater monitoring and remediation at LANL. It is a very flexible method that can also be applied with a variety of other predictors applied to model the water level wells in the area of interest over the historical record. The smoothness of the spatial process and its possible evolution over time can then be estimated from the residuals from this regression. This can be augmented by expert hydrogeological opinion based on site topography and hydrogeology. (authors)

54 ENVIRONMENTAL SCIENCES↗

Transformation rate maps of dissolved organic carbon in the contiguous US

Riverine dissolved organic carbon (DOC) plays a vital role in regional and global carbon cycles. However, the processes of DOC conversion from soil organic carbon (SOC) and leaching into rivers are insufficiently understood, inconsistently represented, and poorly parameterized, particularly in land surface and Earth system models. As a first attempt to fill this gap, we propose a generic formula that directly connects SOC concentration with DOC concentration in headwater streams, where a single parameter, the transformation rate from SOC in the soil to DOC leaching flux (P r ), accounts for the overall processes governing SOC conversion to DOC and leaching from soils (along with runoff) into headwater streams. We then derive high-resolution P r maps over the contiguous US (CONUS) using SOC data from two different sources: the Harmonized World Soil Database v1.2 (HWSD) and SoilGrids 2.0. Both maps are developed following the same five major steps: (1) selecting independent catchments where observed riverine DOC data are available with reasonable quality; (2) estimating catchment-average SOC for the independent catchments; (3) estimating the P r values for these catchments based on the generic formula and catchment-average SOC; (4) developing a predictive model of P r with machine learning (ML) techniques and catchment-scale climate, hydrology, geology, and other attributes; and (5) deriving a national map of P r based on the ML model. For evaluation, we compare the DOC concentration derived using the P r map and the observed DOC concentration values at evaluation catchments. The resulting mean absolute scaled error and coefficient of determination are 0.73 and 0.47 for the HWSD-based model and 0.58 and 0.72 for the SoilGrids-based model, respectively, suggesting the effectiveness of the overall methodology. Efforts to constrain uncertainty and evaluate sensitivity of P r to different factors are discussed. To illustrate the use of such maps, we derive a riverine DOC concentration reanalysis dataset over CONUS. The two P r maps, robustly derived and empirically validated, lay a critical cornerstone for better simulating the terrestrial carbon cycle in land surface and Earth system models. Our findings not only set a foundation for improving our predictive understanding of the terrestrial carbon cycle at the regional and global scales, but also hold promises for informing policy decisions related to decarbonization and climate change mitigation. The data presented in this study are publicly available at https://doi.org/10.5281/zenodo.14563816 (Li et al., 2024).

54 ENVIRONMENTAL SCIENCES↗

The Ohio River Valley CO2 Storage Project AEP Mountaineer Plan, West Virginia

This report includes an evaluation of deep rock formations with the objective of providing practical maps, data, and some of the issues considered for carbon dioxide (CO{sub 2}) storage projects in the Ohio River Valley. Injection and storage of CO{sub 2} into deep rock formations represents a feasible option for reducing greenhouse gas emissions from coal-burning power plants concentrated along the Ohio River Valley area. This study is sponsored by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL), American Electric Power (AEP), BP, Ohio Coal Development Office, Schlumberger, and Battelle along with its Pacific Northwest Division. An extensive program of drilling, sampling, and testing of a deep well combined with a seismic survey was used to characterize the local and regional geologic features at AEP's 1300-megawatt (MW) Mountaineer Power Plant. Site characterization information has been used as part of a systematic design feasibility assessment for a first-of-a-kind integrated capture and storage facility at an existing coal-fired power plant in the Ohio River Valley region--an area with a large concentration of power plants and other emission sources. Subsurface characterization data have been used for reservoir simulations and to support the review of the issues relating to injection, monitoring, strategy, risk assessment, and regulatory permitting. The high-sulfur coal samples from the region have been tested in a capture test facility to evaluate and optimize basic design for a small-scale capture system and eventually to prepare a detailed design for a capture, local transport, and injection facility. The Ohio River Valley CO{sub 2} Storage Project was conducted in phases with the ultimate objectives of demonstrating both the technical aspects of CO{sub 2} storage and the testing, logistical, regulatory, and outreach issues related to conducting such a project at a large point source under realistic constraints. The site characterization phase was completed, laying the groundwork for moving the project towards a potential injection phase. Feasibility and design assessment activities included an assessment of the CO{sub 2} source options (a slip-stream capture system or transported CO{sub 2}); development of the injection and monitoring system design; preparation of regulatory permits; and continued stakeholder outreach.

01 COAL, LIGNITE, AND PEAT↗

Evaluation of Used Fuel Disposition in Clay-Bearing Rock

The DOE R&D program under the Spent Fuel Waste Science Technology (SFWST) campaign has made key progress in modeling and experimental approaches towards the characterization of chemical and physical phenomena that could impact the long-term safety assessment of nuclear waste disposition in deep clay/shale/argillaceous rock. Interactional collaboration activities such as heater tests, particularly postmortem sample recovery and analysis, have elucidated important information regarding changes in engineered barrier system (EBS) material exposed to years of thermal loads. Chemical and structural analyses of bentonite material from such tests has been key to the characterization of thermal effects affecting clay composition, sorption behavior, and swelling. These are crucial to evaluating the nature and extent of bentonite barrier sacrificial zones in the EBS during the thermal period. Thermal, hydrologic, and chemical data collected from heater tests and laboratory experiments has been used in the development and validation of THMC simulators to model near-field coupled processes affecting engineered and natural barrier materials, particularly during the thermal period. This information leads to the development of simulation approaches (e.g., continuum vs. discrete) to tackle issues related to flow and transport depending on the nature of the host-rock and EBS design concept. This report describes R&D efforts on disposal in argillaceous geologic media through developments of coupled THMC process models, hydrothermal experiments and characterization of clay/metal barrier material interactions, and spent fuel and canister material degradation. Currently, the THM modeling focus is on heater test experiments in argillite rock and gas migration in bentonite as part of international collaboration activities at underground research laboratories (URLs). In addition, field testing at an URL involves probing of fault movement and characterization of fault permeability changes. Analyses of barrier samples (bentonite) from heater tests at URLs provide compositional and structural data to evaluate changes in clay swelling and thermal behavior with distance from the heater surface. Development of a spent fuel degradation model coupled with canister corrosion effects has been centered towards its integration with Generic Disposal System Analysis (GDSA) to describe source term behavior. As in previous milestone deliverables, this report is structured according to various national laboratory contributions describing R&D activities applicable to clay/shale/argillite media.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

BFS, a Legacy to the International Reactor Physics, Criticality Safety, and Nuclear Data Communities

Two Organization for Economic Cooperation and Development (OECD) Nuclear Energy Agency (NEA) programs, the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and the International Reactor Physics Experiment Evaluation Project (IRPhEP) have been identifying existing integral experiment data, evaluating those data, and providing integral benchmark specifications for methods and data validation for nearly two decades. The Russian Federation, IPPE, and the BFS laboratories have made substantial contributions to those two projects. Contributions from the BFS facilities are highlighted in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗