Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BASE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

On the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Trefny, Charles J.↗

Simultaneous laboratory measurements of CO2 and H2O adsorption on palagonite: Implications for the Martian climate and volatile reservoir

We are measuring the simultaneous adsorption of H2O and CO2 on palagonite materials in order to improve the formulation of climate models for Mars. We report on the initial co-adsorption data. Models of the Martian climate and volatile inventory indicate that the regolith serves as one of the primary reservoirs of outgassed volatiles and that it exchanges H2O and CO2 with the atmosphere in response to changes in insolation associated with astronomical cycles. Physical adsorbate must exist on the surfaces of the cold particulates that constitute the regolith, and the size of that reservoir can be assessed through laboratory measurements of adsorption on terrestrial analogs. Many studies of the independent adsorption of H2O and CO2 on Mars analog were made and appear in the literature. Empirical expressions that relate the adsorptive coverage of each gas to the temperature of the soil and partial pressure have been derived based on the laboratory data. Numerical models incorporate these adsorption isotherms into climatic models, which predict how the adsorptive coverage of the regolith and hence, the pressure of each gas in the atmosphere will vary as the planet moves through its orbit. These models suggest that the regolith holds several tens to hundreds of millibars of CO2 and that during periods of high obliquity warming of the high-latitude regolith will result in desorption of the CO2, and a consequent increase in atmospheric pressure. At lower obliquities, the caps cool and the equator warms forcing the desorption of several tens of millibars of CO2, which is trapped into quasipermanent CO2 caps.

Zent, A. P.↗

International Satellite Cloud Climatology Project (ISCCP) Stage B3 Reduced Radiances in Native (NAT) Format (ISCCP_B3_NAT)

Since 1983 an international group of institutions has collected and analyzed satellite radiance measurements from up to five geostationary and two polar orbiting satellites to infer the global distribution of cloud properties and their diurnal, seasonal and interannual variations. The primary focus of the first phase of the project (1983-1995) was the elucidation of the role of clouds in the radiation budget (top of the atmosphere and surface). In the second phase of the project (1995 onwards) the analysis also concerns improving understanding of clouds in the global hydrological cycle. [Location=TROPOSPHERE] [Temporal_Coverage: Start_Date=1983-07-01; Stop_Date=] [Spatial_Coverage: Southernmost_Latitude=-90; Northernmost_Latitude=90; Westernmost_Longitude=-180; Easternmost_Longitude=180] [Data_Resolution: Latitude_Resolution=30 Km; Longitude_Resolution=30 Km; Temporal_Resolution=3 Hourly].

CLOUD PARTICLE SIZE↗

Robust block magnetism in the spin ladder compound BaFe 2 Se 3 under hydrostatic pressure

The majority of the iron-based superconductors (FeSCs) exhibit a two-dimensional square lattice structure. Recent reports of pressure-induced superconductivity in the spin-ladder system, BaFe 2 X 3 (X=S, Se), introduce a quasi-one-dimensional prototype and an insulating parent compound to the FeSCs. In this work, we report x-ray, neutron diffraction, and muon spin relaxation experiments on BaFe 2 Se 3 under hydrostatic pressure to investigate its magnetic and structural properties across the pressure-temperature phase diagram. A structural phase transition was found at a pressure of 3.7(3) GPa. Neutron diffraction measurements at 6.8(3) GPa and 120 K show that the block magnetism persists even at these high pressures. A steady increase and then fast drop of the magnetic transition temperature T N and greatly reduced moment above the pressure P s indicate potentially rich and competing phases close to the superconducting phase in this ladder system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thorium and Rare Earth Monoxides and Related Phases

Thorium was a part of energy infrastructure in the 19th century due to the refractory and electronic properties of its dioxide. It will be a part of future energy infrastructure as the most abundant energy reserve based on nuclear fission. This paper discusses the solid-state chemistry of the monoxides and related rocksalt phases of thorium and the rare earths, both at atmospheric and at high pressure. The existence of solid thorium monoxide was first suggested more than 100 years ago; however, it was never obtained in bulk and has been studied mostly theoretically. Monoxides of lanthanides from Eu to Ho are ferromagnetic semiconductors sought for spintronics and were studied in thin films. La to Sm metallic monoxides were synthesized in bulk at pressures below 5 GPa. Recently, ThO formation in thin films has been reported and the stability of bulk ThO at high pressure was theoretically predicted based on first principles computations at 0 K. New ab initio computations were performed accounting for temperature effects up to 1000 K using lattice dynamics in the quasi-harmonic approximation. New computational results confirm the stabilization of pure ThO above 30 GPa and suggest the possibility of high-pressure synthesis of (Th,Nd)O at 1000 K and 5 GPa.

36 MATERIALS SCIENCE↗

A multiscale MDCT image-based breathing lung model with time-varying regional ventilation

A novel algorithm is presented that links local structural variables (regional ventilation and deforming central airways) to global function (total lung volume) in the lung over three imaged lung volumes, to derive a breathing lung model for computational fluid dynamics simulation. The algorithm constitutes the core of an integrative, image-based computational framework for subject-specific simulation of the breathing lung. For the first time, the algorithm is applied to three multi-detector row computed tomography (MDCT) volumetric lung images of the same individual. A key technique in linking global and local variables over multiple images is an in-house mass-preserving image registration method. Throughout breathing cycles, cubic interpolation is employed to ensure C{sub 1} continuity in constructing time-varying regional ventilation at the whole lung level, flow rate fractions exiting the terminal airways, and airway deformation. The imaged exit airway flow rate fractions are derived from regional ventilation with the aid of a three-dimensional (3D) and one-dimensional (1D) coupled airway tree that connects the airways to the alveolar tissue. An in-house parallel large-eddy simulation (LES) technique is adopted to capture turbulent-transitional-laminar flows in both normal and deep breathing conditions. The results obtained by the proposed algorithm when using three lung volume images are compared with those using only one or two volume images. The three-volume-based lung model produces physiologically-consistent time-varying pressure and ventilation distribution. The one-volume-based lung model under-predicts pressure drop and yields un-physiological lobar ventilation. The two-volume-based model can account for airway deformation and non-uniform regional ventilation to some extent, but does not capture the non-linear features of the lung.

42 ENGINEERING↗

Nonlinear mirror structures in a plasma with thermal pressure anisotropy

An asymptotic model based on a reductive perturbative expansion of the drift kinetic and the Maxwell equations, is used to demonstrate that, near the instability threshold, the nonlinear dynamics of mirror modes in a magnetized plasma with anisotropic ion temperatures, involves a subcritical bifurcation, leading to the formation of small-scale structures with amplitudes comparable with the ambient magnetic field. The influence of quasilinear effects on the initial stage of formation of mirror structures is discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Transition characteristics of low-pressure discharges in a hollow cathode

Based on a two-dimensional (2-D) fluid model, the transition processes of discharges in a hollow cathode at low pressure are observed by changing three parameters, i.e., applied voltage U 0 , gas pressure p, and external circuit ballast resistance R b . The voltage-current characteristic curves, electron density distributions, and electric potential distributions of different discharge operating points in a hollow cathode are obtained. The transition processes are characterized by the voltage-current characteristic curves, the electron density distributions, and the electrical potential distributions. The transition modes observed from the voltage-current characteristics include the low-current abnormal mode, normal mode, and high-current abnormal mode. Increasing the applied voltage U0 can have a similar effect on the discharge transition processes to decreasing the ballast resistance. By increasing U0 from 200V to 500V and decreasing Rb from 5000 kX to 100 kX independently, it is observed that the discharge transfers from the outside to the inside of the hollow cavity, thus forming the virtual anode potential. By increasing the gas pressure p from 50 Pa to 5 kPa, the discharge also moves into the hollow cavity from the outside; however, a further increase in the gas pressure leads to the discharge escaping from the hollow cavity. Simulation results and characterizations for different parameters are presented for the transition properties of low-pressure discharges in a hollow cathode. It is verified that the hollow cathode discharge only exists under certain ranges of the above parameters.

42 ENGINEERING↗

Software compensated multichannel pressure sensing system

A PC-based software system is described which can be used for data acquisition and thermal-error correction of a multichannel pressure-sensor system developed for use in a cryogenic environment. The software incorporates pressure-sensitivity and sensor-offset compensation files into thermal error-correction algorithms, and the sensors are calibrated by simulating the operating conditions. The system is found to be effective in the collecting, storing, and processing of multichannel pressure-sensor data to correct thermally induced offset and sensitivity errors.

Chapman, John J.↗

Experimental results on a wall interference correction method with interface measurements

A wall interference assessment and correction method for subsonic two-dimensional wind tunnel testing is presented. This method calculates a pressure coefficient and angle of attack correction based on velocity measurements on interfaces inside of the wind tunnel. A mathematical representation of the test article is not required. An experimental verification of the suggested technique is given. A NACA 0012 airfoil is tested at a Mach number of 0.70 and at two different angles of attack. Calculated blockage corrections show reasonable agreement with results based on Hackett's method. Corrected surface pressures compare favorably to free-air flow field data if the tunnel flow field is subsonic. The present wall interference correction method can be applied to transonic tunnel flow fields with some restrictions. Errors are estimated and it is shown that the expected error in calculating the pressure coefficient correction on the model surface is in the order of the error of pressure coefficient measurement on interfaces. Necessary testing equipment in existing tunnels can easily be modified if the present method is applied.

Lo, C. F.↗

Numerical Analysis of Detonability Assessment in a Natural Gas-Air Fueled Rotating Detonation Engine

Rotating Detonation Engines (RDE) offer an alternative combustion strategy to replace conventional constant pressure combustion with a process that could produce a pressure gain without the use of a mechanical compressor. Recent numerical and experimental publications that consider air as the oxidizer have primarily focused on the ability of these annular combustors to sustain a stable continuous detonation wave when fueled by hydrogen. However, for this to be a viable consideration for the land-based power generation it is necessary to explore the ability to detonate natural gas and air within the confines of the annular geometry of an RDE. Previous studies on confined detonations have expressed the importance of permitting detonation cells to fully form within the combustor in order to achieve stability. This poses a challenge for natural gas–air fueled processes as their detonation cell size can be quite large even at moderate pressures. Despite the practical importance, only a few studies are available on natural gas detonations for air-breathing RDE applications. Moreover, the extreme thermodynamic condition (high temperature inside the combustor) allows limited accessibility inside the combustor for detailed experimental instrumentations, providing mostly single-point data. Recent experimental studies at the National Energy Technology Laboratory (NETL) have reported detonation failure at higher methane concentration in an air-breathing RDE fueled by natural gas-hydrogen fuel blends. This encourages to perform a detailed numerical investigation on the wave characteristics of detonation in a natural gas-air fueled RDE to understand the various aspects of instability associated with the natural gas-air detonation.This study is a numerical consideration of a methane-air fueled RDE with varying operating conditions to ascertain the ability to achieve a stable, continuous detonation wave. The simulations have been performed in a 2D unwrapped RDE geometry using the open-source CFD library “OpenFOAM” employing an unsteady pressure-based compressible reactive flow solver with a <em>k</em>–<em>ε</em> turbulence model in a structured rectangular grid system. Both reduced and detailed chemical kinetic models have been used to assess the effect of the chemistry on the detonation wave characteristics and the underlying flow features. A systematic grid sensitivity study has been conducted with various grid sizes to quantify the weakly stable overdriven detonation on a coarse mesh and oscillating features at fine mesh resolutions.The main focus of the current study is to investigate the effects of operating injection pressure on detonation wave characteristics of an air-breathing Rotating Detonation Engine (RDE) fueled with natural gas-hydrogen fuel blends. Wave speeds, peak pressures and temperatures, and dominant frequencies have been computed from the time histories. The flow structures were then visualized using 2D contours of temperature and species concentration.

Saha, Pankaj↗

Highly efficient Cu-decorated iron oxide nanocatalyst for low pressure CO2 conversion

We report a nanoparticulate iron oxide based catalyst for CO2 conversion with high efficiency at low pressures and on the effect of the presence of copper on the catalyst’s restructuring and its catalytic performance. In situ X-ray scattering reveals the restructuring of the catalyst at the nanometer scale. In situ X-ray absorption near edge structure (XANES) shows the evolution of the composition and oxidation state of the iron and copper components under reaction conditions along with the promotional effect of copper on the chemical transformation of the iron component. X-ray diffraction (XRD), XANES and Raman spectroscopy proved that the starting nanocatalyst is composed of iron oxides differing in chemical nature (α-Fe2O3, Fe3O4, FeO(OH)) and dimensionality, while the catalyst after CO2 conversion was identified as a mixture of α-Fe, Fe3C, and traces of Fe5C2. The significant increase of the rate CO2 is turned over in the presence of copper nanoparticles indicates that Cu nanoparticles activate hydrogen, which after spilling over to the neighbouring iron sites, facilitate a more efficient conversion of carbon dioxide.

Benzene↗

Results of transonic wind tunnel tests on an 0.010-scale space shuttle mated vehicle model 72-OTS in the LaRC 8-foot TPT (IA43)

Experimental aerodynamic investigations were conducted in NASA/Langley 8-Foot transonic pressure tunnel on a sting mounted 0.010-scale outer mold line model of 104A/B configuration of the Rockwell International space shuttle vehicle. Component aerodynamic force and moment data and base and balance cavity pressures were recorded over an angle of attack range of -10 deg to +10 deg at Mach numbers of 0.6, 0.8, 0.9, 0.98, 1.13, and 1.2. Selected configurations were tested at sideslip angles from -10 deg to +10 deg. For all configurations involving the orbit, wing bending and torsion were measured on the right wing. Inboard elevon setting of 0 deg, +4 deg and +8 deg and outboard settings of 0 deg, +4 deg and +8 deg were tested.

Petrozzi, M. T.↗

Development of Designer Diamond Technology for High Pressure High Temperature Experiments in Support of Stockpile Stewardship Program

The role of nitrogen in the fabrication of designer diamond was systematically investigated by adding controlled amount of nitrogen in hydrogen/methane/oxygen plasma. This has led to a successful recipe for reproducible fabrication of designer diamond anvils for high-pressure high-temperature research in support of stockpile stewardship program. In the three-year support period, several designer diamonds fabricated with this new growth chemistry were utilized in high-pressure experiments at UAB and Lawrence Livermore National Laboratory. The designer diamond anvils were utilized in high-pressure studies on heavy rare earth metals, high pressure melting studies on metals, and electrical resistance measurements on iron-based layered superconductors under high pressures. The growth chemistry developed under NNSA support can be adapted for commercial production of designer diamonds.

36 MATERIALS SCIENCE↗

Ball tonometry: a rapid, nondestructive method for measuring cell turgor pressure in thin-walled plant cells

In this article we describe a new method for the determination of turgor pressures in living plant cells. Based on the treatment of growing plant cells as thin-walled pressure vessels, we find that pressures can be accurately determined by observing and measuring the area of the contact patch formed when a spherical glass probe is lowered onto the cell surface with a known force. Within the limits we have described, we can show that the load (determined by precalibration of the device) divided by the projected area of the contact patch (determined by video microscopy) provides a direct, rapid, and accurate measure of the internal turgor pressure of the cell. We demonstrate, by parallel measurements with the pressure probe, that our method yields pressure data that are consistent with those from the pressure probe. Also, by incubating target tissues in stepped concentrations of mannitol to incrementally reduce the turgor pressure, we show that the pressures measured by tonometry accurately reflect the predicted changes from the osmotic potential of the bathing medium. The advantages of this new method over the pressure probe are considerable, however, in that we can move rapidly from cell to cell, taking measurements every 20 s. In addition, the nondestructive nature of the method means that we can return to the same cell repeatedly for periodic pressure measurements. The limitations of the method lie in the fact that it is suitable only for superficial cells that are directly accessible to the probe and to cells that are relatively thin walled and not heavily decorated with surface features. It is also not suitable for measuring pressures in flaccid cells.

NASA Discipline Plant Biology↗

3D printed structures for optimized carbon capture technology in packed bed columns

The use of 3D printed structured packing for the optimization of aqueous-amine based carbon capture in packed absorption columns is examined in this paper. An experimental testing system has been set up, and initial comparisons were made between metal, plastic, and 3D printed 16-inch packing elements and between three 8-inch 3D printed elements of different densities. Pressure drop measurements were obtained at various air flowrates under dry conditions. Measurements were also taken for a wet system by adding water at six different liquid flowrates. In each case, theoretical calculations for pressure drop were performed based on a model presented in the literature. It was found that, for the 16-inch dry column, the model slightly overpredicts the pressure drop. The model provides an accurate prediction for the dry 8-inch experimental data, especially for the two least dense packing elements. For the wet system, the model overpredicts the pressure drop, likely due to modeling deficiencies when the column reaches its loading limit. Furthermore, these results provide sufficient confidence to move forward with testing and process intensification of the CO 2 capture process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Signal Processing Methods for Liquid Rocket Engine Combustion Stability Assessments

The J2X Gas Generator engine design specifications include dynamic, spontaneous, and broadband combustion stability requirements. These requirements are verified empirically based high frequency chamber pressure measurements and analyses. Dynamic stability is determined with the dynamic pressure response due to an artificial perturbation of the combustion chamber pressure (bomb testing), and spontaneous and broadband stability are determined from the dynamic pressure responses during steady operation starting at specified power levels. J2X Workhorse Gas Generator testing included bomb tests with multiple hardware configurations and operating conditions, including a configuration used explicitly for engine verification test series. This work covers signal processing techniques developed at Marshall Space Flight Center (MSFC) to help assess engine design stability requirements. Dynamic stability assessments were performed following both the CPIA 655 guidelines and a MSFC in-house developed statistical-based approach. The statistical approach was developed to better verify when the dynamic pressure amplitudes corresponding to a particular frequency returned back to pre-bomb characteristics. This was accomplished by first determining the statistical characteristics of the pre-bomb dynamic levels. The pre-bomb statistical characterization provided 95% coverage bounds; these bounds were used as a quantitative measure to determine when the post-bomb signal returned to pre-bomb conditions. The time for post-bomb levels to acceptably return to pre-bomb levels was compared to the dominant frequency-dependent time recommended by CPIA 655. Results for multiple test configurations, including stable and unstable configurations, were reviewed. Spontaneous stability was assessed using two processes: 1) characterization of the ratio of the peak response amplitudes to the excited chamber acoustic mode amplitudes and 2) characterization of the variability of the peak response's frequency over the test duration. This characterization process assists in evaluating the discreteness of a signal as well as the stability of the chamber response. Broadband stability was assessed using a running root-mean-square evaluation. These techniques were also employed, in a comparative analysis, on available Fastrac data, and these results are presented here.

Kenny, R. Jeremy↗