Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Accelerator experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Containment of a silicone fluid free surface in reduced gravity using barrier coatings

In support of the Surface Tension Driven Convection Experiment planned for flight aboard the Space Shuttle, tests were conducted under reduced gravity in the 2.2-sec Drop Tower and the 5.0-sec Zero-G facility at the NASA Lewis Research Center. The dynamics of controlling the test fluid, a 10-cSt viscosity silicone fluid in a low gravity environment were investigated using different container designs and barrier coatings. Three container edge designs were tested without a barrier coating; a square edge, a sharp edge with a 45-deg slope, and a sawtooth edge. All three edge designs were successful in containing the fluid below the edge. G-jitter experiments were made in scaled down containers subjected to horizontal accelerations. The data showed that a barrier coating is effective in containing silicone fluid under g-levels up to 10 sup -1 sub g sub 0. In addition, a second barrier coating was found which has similar anti-wetting characteristics and is also more durable.

Pline, Alexander D.↗
NASA NTRS1991

Plastic scintillator block as photon beam monitor for EGRET calibration

The EGRET (Energetic Gamma Ray Experiment Telescope) detector has been calibrated at SLAC (Stanford Linear Accelerator) and, to a lesser degree, at the MIT Bates Linear Accelerator Center. To monitor the photon beams for the calibration, a plastic scintillator block, 5 cm x 5 cm in cross section, 15 cm in length, and viewed by a single photomultiplier tube, was used for the entire beam energy range of 15 MeV to 10 GeV. The design operation, and method of analysis of the beam intensity are presented. A mathematical framework has been developed to treat the general case of a beam with multiphoton beam pulses and with a background component. A procedure to deal with the fluctuations of the beam intensity over a data-taking period was also developed. The photon beam monitor is physically sturdy, electronically steady, simple to construct, and easy to operate. Its major merits lie in its sheer simplicity of construction and operation and in the wide energy range it can cover.

Lin, Y. C.↗
NASA NTRS1991

Frequency weighted system identification and linear quadratic controller design

Application of filters for frequency weighting of Markov parameters (pulse response functions) is described in relation to system/observer identification. The time domain identification approach recovers a model which has a pulse response weighted according to frequency. The identified model is composed of the original system and filters. The augmented system is in a form which can be used directly for frequency weighted linear quadratic controller design. Data from either single or multiple experiments can be used to recover the Markov parameters. Measured acceleration signals from a truss structure are used for system identification and the model obtained is used for frequency weighted controller design. The procedure makes the identification and controler design complementary problems.

Horta, Lucas G.↗
NASA NTRS1994

Materials processing in space tasks. WBS task 5.4: Generic tasks

This task encompassed a wide range of activities related to materials processing in space. For example, all aspects of the space station's flight and ground based systems design were assessed for the Office of Advanced Concepts and Technology (OACT) Space Processing Division Office. Activities for that organization also included the consolidation of space processing payload requirements for the space station and the development of an OACT payload operations plan. Similar duties were performed for the MSFC Payload Project Office. The SPACECOM database was used to conduct preliminary design studies for microgravity payload carriers and to conduct assessments of materials processing technology. Concepts for the Advanced Protein Crystal Growth Facility (APCGF) were developed. Materials processing vent products were analyzed and a furnace facility filter concept was developed using those studies. A preliminary design for a space station aluminum payload rack was developed. Analysis was conducted to characterize the acceleration environment onboard the space shuttle. Equipment for two fluid experiment apparatus was designed and manufactured for the Space Science Laboratory. The Fluids and Materials Experiments (FAME) data base was expanded. Also, Mir payload integration, technology transfer, and spacelab-to-space station transition studies were conducted.

Crull, Robert↗
NASA NTRS1995

A review of solar wind ion and electron plasma distribution functions: Present understanding and Ulysses results

Our present understanding of the distribution functions of the solar wind ion and electron thermal/suprathermal populations will be reviewed covering selected theoretical and observational topics. Roughly half the review will be devoted to recent discoveries (since Solar Wind 7). Among recent results are those of the Ulysses mission. The SWICS experiment observed pick-up protons and alpha particles, and acceleration of these particles at interplanetary shocks. Positive ion phenomena observed by SWOOPS include enhanced proton-alpha particle differential streaming both: (1) at high latitudes; and (2) in the ecliptic beyond 1 AU in the vicinity of shocks. The SWOOPS positive ion observations also demonstrate relative constancy of the entropy per proton at high latitudes beyond about 2.5 AU. Double beaming in both protons and alphas is observed by SWOOPS on either side of the current sheet, but not within; a possible explanation is reconnection at the edge of the current sheet. SWOOPS observed bi-directional streaming of electrons beyond 2 AU not only within Coronal Mass Ejections, but also upstream of corotating interplanetary shocks. Latitudinal and radial gradients of Ulysses electron core and halo temperatures will be discussed, as will work in progress on the three dimensional (in velocity space) properties of ion distributions.

Goldstein, B. E.↗
NASA NTRS1994

Rarefield-Flow Shuttle Aerodynamics Flight Model

A model of the Shuttle Orbiter rarefied-flow aerodynamic force coefficients has been derived from the ratio of flight acceleration measurements. The in-situ, low-frequency (less than 1Hz), low-level (approximately 1 x 10(exp -6) g) acceleration measurements are made during atmospheric re-entry. The experiment equipment designed and used for this task is the High Resolution Accelerometer Package (HiRAP), one of the sensor packages in the Orbiter Experiments Program. To date, 12 HiRAP re-entry mission data sets spanning a period of about 10 years have been processed. The HiRAP-derived aerodynamics model is described in detail. The model includes normal and axial hypersonic continuum coefficient equations as function of angle of attack, body-flap deflection, and elevon deflection. Normal and axial free molecule flow coefficient equations as a function of angle of attack are also presented, along with flight-derived rarefied-flow transition bridging formulae. Comparisons are made between the aerodynamics model, data from the latest Orbiter Operational Aerodynamic Design Data Book, applicable computer simulations, and wind-tunnel data.

Blanchard, Robert C.↗
NASA NTRS1998

Containerless Processing in Reduced Gravity Using the TEMPUS Facility during MSL-1 and MSL-1R

Containerless processing provides a high purity environment for the study of high-temperature, very reactive materials. It is an important method which provides access to the metastable state of an undercooled melt. In the absence of container walls, the nucleation rate is greatly reduced and undercooling up to (Tm-Tn)/Tm approx. equal to 0.2 can be obtained, where Tm and Tn are the melting and nucleation temperatures, respectively. Electromagnetic levitation represents a method particularly well-suited for the study of metallic melts. The TEMPUS (Tiegelfreies ElektroMagnetisches Prozessieren Unter Schwerelosgkeit) facility is a research instrument designed to perform electromagnetic levitation studies in reduced gravity. TEMPUS is a joint undertaking between DARA, the German Space Agency, and the Microgravity Science and Applications Division of NASA. The George C. Marshall Space Flight Center provides the leadership for scientific and management efforts which support the four US PI teams which performed experiments in the TEMPUS facility. The facility is sensitive to accelerations in the 1-10 Hz range. This became evident during the MSL-1 mission. Analysis of accelerometer and video data indicated that loss of sample control occurred during crew exercise periods which created disturbances in this frequency range. Prior to the MSL-1R flight the TEMPUS team, the accelerometer support groups and the mission operations team developed a strategy to provide for the operation of the facility without such disturbances. The successful implementation of this plan led to the highly successful operation of this facility during MSL-1R.

Rogers, Jan R.↗
NASA NTRS2021

The Sun Radio Interferometer Space Experiment (SunRISE) Mission

The Sun Radio Interferometer Space Experiment (SunRISE) will provide an entirely new view on particle acceleration and transport in the inner heliosphere by creating the first low radio frequency interferometer in space to localize heliospheric radio emissions. By imaging and determining the location of decametric-hectometric (DH) radio bursts from 0.1 MHz–25 MHz, SunRISE will provide key information on particle acceleration mechanisms associated with coronal mass ejections (CMEs) and the magnetic field topology from active regions into interplanetary space. Six small spacecraft, of a 6U form factor, will fly in a supersynchronous geosynchronous Earth orbit (GEO) orbit within about 10 km of each other, in a passive formation, and image the Sun in a portion of the spectrum that is blocked by the ionosphere and cannot be observed from Earth. Key aspects that enable this mission are that only position knowledge of the spacecraft is required, not active control, and that the architecture involves a modest amount of on-board processing coupled with significant ground-based processing for navigation, position determination, and science operations. Mission-enabling advances in software-defined radios, GPS navigation and timing, and small spacecraft technologies, developed and flown on the DARPA High Frequency Research (DHFR), the Community Initiative for Continuing Earth Radio Occultation (CICERO), and the Mars Cube One (MarCO) missions, have made this mission affordable and low-risk. The SunRISE mission will involve utilizing commercial access to space, in which the SunRISE spacecraft will be carried to their target orbit as a secondary payload in conjunction with a larger host spacecraft intended for GEO.

Neilson, Tim↗
NASA NTRS2022

The Sun Radio Interferometer Space Experiment (SunRISE) Mission

The Sun Radio Interferometer Space Experiment (SunRISE) will provide an entirely new view on particle acceleration and transport in the inner heliosphere by creating the first low radio frequency interferometer in space to localize heliospheric radio emissions. By imaging and determining the location of decametric-hectometric (DH, 0.1 MHz–23 MHz) solar radio bursts, SunRISE will provide key information on particle acceleration mechanisms associated with coronal mass ejections (CMEs) and the magnetic field topology from active regions into interplanetary space. The SunRISE Observatory will consist of six space vehicles in a passive formation, in orbits designed to keep them within approximately 10 km of each other, and flying in a supersynchronous geosynchronous Earth orbit (GEO). Each space vehicle consists of a Solar DH-GNSS payload and a 6U form factor spacecraft. The SunRISE Observatory together with significant ground-based processing, will enable imaging of the Sun in a portion of the spectrum that is blocked by the ionosphere and cannot be observed from Earth. Key aspects that enable this mission are that only position knowledge of the space vehicles is required, not active control, and that the architecture involves a modest amount of on-board processing coupled with significant ground-based processing for navigation, position determination, and science operations. Mission-enabling advances in software-defined radios, GPS navigation and timing, and small spacecraft technologies, developed and flown on the DARPA High Frequency Research (DHFR) and the Community Initiative for Continuing Earth Radio Occultation (CICERO) have made this mission affordable and low-risk. The SunRISE mission will exploit the multiple spacecraft per aperture (MSPA) capability of NASA’s Deep Space Network (DSN), for more efficient data transfers of larger data volumes, and utilize commercial access to space, in which the SunRISE space vehicles will be carried to their target orbit as secondary payloads in conjunction with a larger host spacecraft intended for GEO.

Neilson, Tim↗
DOE OSTI2022

Additive manufacturing of composite neutron absorbing components

Collimators and other components for use in neutron scattering experiments or to provide neutron shielding in nuclear reactors or accelerator based neutron sources are produced by additive manufacturing from multiple different types of material, such as boron carbide (B4C), steel, isotopically enriched boron carbide (10B4C), and blends thereof.

Anderson, David C.↗
DOE OSTI2024

Method for producing neutron collimators using additive manufacturing

Collimators and other components for use in neutron scattering experiments or to provide neutron shielding in nuclear reactors or accelerator based neutron sources are produced by additive manufacturing from neutron absorbing material, such as boron carbide (B4C) or isotopically enriched boron carbide (10B).

Anderson, David C.↗
NASA NTRS1991

Development of an electrostatic propulsion engine using sub-micron powders as the reaction mass

Asteroid sample return missions would benefit from development of an improved rocket engine. Chemical rockets achieve their large thrust with high mass consumption rate (dm/dt) but low exhaust velocity; therefore, a large fraction of their total mass is fuel. Present day ion thrusters are characterized by high exhaust velocity, but low dm/dt; thus, they are inherently low thrust devices. However, their high exhausy velocity is poorly matched to typical mission requirements and therefore, wastes energy. A better match would be intermediate between the two forms of propulsion. This could be achieved by electrostatically accelerating solid powder grains, raising the possibility that interplanetary material could be processed to use as reaction mass. An experiment to study the charging properties of sub-micron sized powder grains is described. If a suitable material can be identified, then it could be used as the reaction mass in an electrostatic propulsion engine. The experiment employs a time of flight measurement to determine the exhaust velocity (v) of various negatively charged powder grains that were charged and accelerated in a simple device. The purpose is to determine the charge to mass ratio that can be sustained for various substances. In order to be competitive with present day ion thrusters, a specific impulse (v/g) of 3000 to 5000 seconds is required. Preliminary results are presented. More speculatively, there are some mission profiles that would benefit from collection of reaction mass at the remote asteroid site. Experiments that examine the generation of sub-micron clusters by electrostatic self-disruption of geologically derived material are planned.

Herbert, F.↗
NASA NTRS1997

Passive Vibration Control of Airborne Equipment using a Circular Steel Ring

Vibration isolation is needed to protect avionics equipment from adverse aircraft vibration environments. Passive isolation is the simplest means to achieve this goal. The system used here consists of a circular steel ring with a lump mass on top and exposed to base excitation. Sinusoidal and filtered zero-mean Gaussian white noise are used to excite the structure and the acceleration response spectra at the top of the ring are computed. An experiment is performed to identify the natural frequencies and modal damping of the circular ring. Comparison is made between the analytical and experimental results and good agreement is observed. The ring response is also evaluated with a concentrated mass attached to the top of the ring. The effectiveness of the ring in isolating the equipment from base excitation is studied. The acceleration response spectra of a single degree of freedom system attached to the top of the ring are evaluated and the results are compared with those exposed directly to the base excitation. It is shown that a properly designed ring could effectively protect the avionics from possible damaging excitation levels.

Ellison, Joseph↗
DOE OSTI2024

Understanding Mixed Precision GEMM with MPGemmFI: Insights into Fault Resilience

Emerging deep learning workloads urgently need fast general matrix multiplication (GEMM). Thus, one of the critical features of machine-learning-specific accelerators such as NVIDIA Tensor Cores, AMD Matrix Cores, and Google TPUs is the support of mixed-precision enabled GEMM. For DNN models, lower-precision FP data formats and computation offer acceptable correctness but significant performance, area, and memory footprint improvement. While promising, the mixed-precision computation on error resilience remains unexplored. To this end, we develop a fault injection framework that systematically injects fault into the mixed-precision computation results. We investigate how the faults affect the accuracy of machine learning applications. Based on the characteristics of error resilience, we offer lightweight error detection and correction solutions that significantly improve the overall model accuracy by 75% if the models experience hardware faults. The solutions can be efficiently integrated into the accelerator's pipelines.

Fang, Bo↗
DOE OSTI2020

Lightwave terahertz quantum manipulation of nonequilibrium superconductor phases and their collective modes

In this work, we present a gauge-invariant density matrix description of nonequilibrium superconductor (SC) states with spatial and temporal correlations driven by intense terahertz (THz) lightwaves. We derive superconductor Bloch-Maxwell equations of motion that extend Anderson pseudospin models to include the Cooper pair center-of-mass motion and electromagnetic propagation effects. We thus describe quantum control of dynamical phases, collective modes, quasiparticle coherence, and high nonlinearities during cycles of carrier wave oscillations, which relates to our recent experiments. Coherent photogeneration of a nonlinear supercurrent with a dc component, achieved via condensate acceleration by an effective lightwave field, dynamically breaks the equilibrium inversion symmetry. Experimental signatures include high harmonic light emission at equilibrium-symmetry-forbidden frequencies, Rabi-Higgs collective modes and quasiparticle coherence, and nonequilibrium moving condensate states tuned by few-cycle THz fields. We use such lightwaves as an oscillating accelerating force that drives strong nonlinearities and anisotropic quasiparticle populations to control and amplify different classes of collective modes, e.g., damped oscillations, persistent oscillations, and overdamped dynamics via Rabi flopping. Recent phase-coherent nonlinear spectroscopy experiments can be modeled by solving the full nonlinear quantum dynamics including self-consistent light-matter coupling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

805 Stepped Plan Project Description

The 805 MHz system utilizes 1.25 MW class klystron amplifiers. The Solid-State Amplifier (SSA) technology has been utilized in the SC accelerator technology, but more powerful sources are needed for use in the NC accelerator facilities such as LASNCE. The SSA topologies that are widely used need to be scaled and tested for reliability and operation in a high impact accelerator facility, such as the 805 MHz SCCL in Los Alamos. Operational experience with high power SSA needs to be assessed prior to installation of an SSA unit at LANSCE. The RFE group at LANSCE is looking for collaboration in the development of the Solid-State Amplifier.

43 PARTICLE ACCELERATORS↗
NASA NTRS2004

Basic Research on the Composition of Heavy Cosmic Rays: The Trans-Iron Galactic Element Recorder Experiment (TIGER)

Among the most fundamental astrophysical problems is understanding the mechanism by which particles are accelerated to the enormous energies observed in the cosmic rays. That problem can be conveniently divided into two questions: (1) What is the source of the energy and the mechanism for converting the energy of that source into the energy of individual cosmic-ray nuclei, and (2) what is the source of the material that is accelerated and the mechanism for injecting that material into the cosmic-ray accelerator? There is a general consensus that the answer to the first of these questions, for nuclei with energy eV, is that the source of their energy is almost certainly from supernova explosions (e.g., Ginzburg & Syrovatskii, 1964). The answer to the second question is still uncertain, although evidence in favor of a superbubble origin of cosmic rays is becoming quite significant (Higdon et al, 2203 and Binns, 2005 (Submitted to ApJ). There are several ways of interpreting available data that lead to quite different models for the source of the material and its injection mechanism. With the The Trans-Iron Galactic Element Recorder Experiment (TIGER) instrument we have obtained data that will help to distinguish among these possible models. In the report, the TIGER flights, the instrument itself, results, and a publication list as a result of the work are presented.

Binns, W. Robert↗