SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Investigations on an 0.030-scale space shuttle vehicle configuration 140A/B orbiter model in the Ames Research Center 9 by 7-foot supersonic wind tunnel (OA53B)

A wind tunnel test of an 0.030-scale space shuttle vehicle orbiter configuration 140A/B model was conducted in the Ames Research Center 9- by 7-foot supersonic wind tunnel. This part of test series OA53 was conducted at Mach numbers of 1.60 and 2.00 and at Reynolds numbers ranging from 1.0 million per foot to 4.0 million per foot. The objective was to establish and verify longitudinal and lateral-directional aerodynamic performance, stability, and control characteristics for the configuration 140A/B SSV orbiter. Reynolds number studies were performed on certain nominal control-setting configurations, and examinations were made of the incremental effects of an alternate wing leading-edge configuration and of a sealed elevon-split construction. Six-component force and moment data, base and cavity pressures, bodyflap, elevon, speedbrake, and rudder hinge moments, and vertical tail forces and moments were measured for the orbiter.

Nichols, M. E.↗

NASA NTRS1982

Investigation of the interference effects of mixed flow long duct nacelles on a DC-10 wing

Wind tunnel test results utilizing a 4.7 percent scale semispan model in the 11 foot transonic wind tunnel are presented. A low drag long duct nacelle installation for the DC-10 jet transport was developed. A long duct nacelle representative of a CF6-50 mixed flow configuration was investigated on the DC-10-30. The results showed that the long duct nacelle installation located in the same position as the current short duct nacelle and with the current production symmetrical pylon is a relatively low risk installation for the DC-10 aircraft. Tuft observations and analytical boundary layer analysis confirmed that the flow on the nacelle afterbody was attached. A small pylon fairing was evaluated and found to reduce channel peak suction pressures, which resulted in a small drag improvement. The test also confirmed that the optimum nacelle incidence angle is the same as for the short duct nacelle, thus the same engine mount as for the production short duct nacelle can be used for the long duct nacelle installation. Comparison of the inboard wing pylon nacelle channel pressure distributions, with flow through and powered long duct nacelles showed that the power effects did not change the flow mechanism; hence, power effects can be considered negligible.

Patel, S. P.↗

NASA NTRSDate not supplied

X-57 “Maxwell” High-Lift Propeller Testing and Model Development

NASA’s X-57 “Maxwell” distributed electric propulsion flight demonstrator has a high-lift system that includes 12 fixed-pitch high-lift propellers located upstream of the wing leading edge for lift augmentation at low speeds. These high-lift propellers are not required at higher speeds and are folded conformally along the nacelles to reduce drag when not in operation. Aircraft performance models and flight simulations incorporate propeller performance to predict thrust, moments, and power consumption and propeller model accuracy is important in identifying safe operating regimes for this aircraft. Current high-lift propeller performance models have been verified and calibrated against numerous computational fluid dynamics analyses under a variety of flight conditions. We performed a series of full-scale wind tunnel tests at the NASA Langley Research Center Low Speed Aeroacoustic Wind Tunnel to further validate these models, to identify any adverse operating conditions for these propellers, and to assess the accuracy of the facility’s new Propeller Test Stand. The results indicate that the models accurately predicted performance and that the right-handed propeller showed lower torque and thrust for a given propeller speed compared to the left-handed version. Acoustic data support these measurements, showing higher tonal noise for the left versus right propeller. We suspect this is due to slight differences in the material properties between the early production (right) and more recent (left) blade sets leading to greater detwisting in the right-handed blades under load. Both propellers demonstrated very stable operation throughout the test including during deployment, stowing, and windmilling. Furthermore, high-speed imagery of the spinning propeller indicated no blade oscillations or instabilities for any test case. We also leveraged these images to analyze the effects of propeller loading on blade detwisting and tip position. Unfortunately, the thrust measurements varied significantly during the test due to cross-loading of the Propeller Test Stand load cell, though trends in the thrust data were still observable. The torque measurement, however, remained very precise for all test points and was used for performance comparisons. As a result of this test, we validated and improved the X-57 high-lift propeller performance models, obtained detailed propeller acoustic data and high-speed imagery, observed the propeller operating safely during a variety of dynamic events, and identified two potentially adverse, low-propeller-speed conditions which will be avoided during normal aircraft operation.

X-57↗

NASA NTRS1997

Scaling Methods for Simulating Aircraft In-Flight Icing Encounters

This paper discusses scaling methods which permit the use of subscale models in icing wind tunnels to simulate natural flight in icing. Natural icing conditions exist when air temperatures are below freezing but cloud water droplets are super-cooled liquid. Aircraft flying through such clouds are susceptible to the accretion of ice on the leading edges of unprotected components such as wings, tailplane and engine inlets. To establish the aerodynamic penalties of such ice accretion and to determine what parts need to be protected from ice accretion (by heating, for example), extensive flight and wind-tunnel testing is necessary for new aircraft and components. Testing in icing tunnels is less expensive than flight testing, is safer, and permits better control of the test conditions. However, because of limitations on both model size and operating conditions in wind tunnels, it is often necessary to perform tests with either size or test conditions scaled. This paper describes the theoretical background to the development of icing scaling methods, discusses four methods, and presents results of tests to validate them.

Anderson, David N.↗

NASA NTRS2012

Blade Displacement Measurement Technique Applied to a Full-Scale Rotor Test

Blade displacement measurements using multi-camera photogrammetry were acquired during the full-scale wind tunnel test of the UH-60A Airloads rotor, conducted in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel. The objectives were to measure the blade displacement and deformation of the four rotor blades as they rotated through the entire rotor azimuth. These measurements are expected to provide a unique dataset to aid in the development and validation of rotorcraft prediction techniques. They are used to resolve the blade shape and position, including pitch, flap, lag and elastic deformation. Photogrammetric data encompass advance ratios from 0.15 to slowed rotor simulations of 1.0, thrust coefficient to rotor solidity ratios from 0.01 to 0.13, and rotor shaft angles from -10.0 to 8.0 degrees. An overview of the blade displacement measurement methodology and system development, descriptions of image processing, uncertainty considerations, preliminary results covering static and moderate advance ratio test conditions and future considerations are presented. Comparisons of experimental and computational results for a moderate advance ratio forward flight condition show good trend agreements, but also indicate significant mean discrepancies in lag and elastic twist. Blade displacement pitch measurements agree well with both the wind tunnel commanded and measured values.

Abrego, Anita I.↗

NASA NTRSDate not supplied

Development of Neural Network for X-59 Air Data Probe Calibration

Two wind tunnel tests were conducted in the NASA Glenn Research Center (GRC) 8- by 6-Foot Supersonic Wind Tunnel to calibrate the nose-mounted air data probe for the X-59. The probe will be the primary instrument for the flight test of the X-59 for determining angle of attack, angle of sideslip, airspeed, and pressure altitude of the aircraft in flight. This paper documents the development of several neural net algorithms that can be used to relate air data probe port pressures from those tests to relevant X-59 flight parameters, such as angle of attack, angle of sideslip, mach number, and static and dynamic pressure. These calibration algorithms address accuracy effects for significant real-world conditions, such as initial sensor measurement uncertainties, assumed parameter constraints on NN modelling errors, and malfunctioning or plugged ports. Resultant integrated uncertainties are provided for each algorithm; these uncertainties are then used to estimate the effects on relevant X-59 mission parameters.

Kurtis Roy Long↗

NASA NTRS2023

Experimental Investigation of Block-TPS Fence/Gap Roughness Effects on Transition Onset and Turbulent Heating at Mach 6

An experimental investigation of boundary-layer transition and convective surface heating on wind tunnel models that simulated aeroshells comprised of multiple blocks of thermal protection system (TPS) material has been performed. Two representative entry vehicle geometries, a sphere-cone aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with varying fence heights or gap depths to represent gap fillers that either protrude above, or are recessed below, the TPS blocks due to differential ablation during reentry. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Convective surface heating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations.

Aerothermodynamics↗

NASA NTRS1971

Heat transfer tests of the NASA-MSC space shuttle configuration at the Langley Research Center Mach 8 Variable Density Facility

The experimental investigations performed on the NASA-Manned Spacecraft Center Space Shuttle orbiter and booster configurations at a Mach 8 variable density facility are presented. The test program was a series of aerothermodynamic wind tunnel tests that were run over a range of angles of attack, yaw angles, and Reynolds numbers. Objectives of the test program were to obtain heat transfer data over the NASA-Manned Spacecraft Center Space Shuttle orbiter, booster, and launch configurations for a range of angles of attack from - 20 to + 30 deg, yaw angles of 0 and + or - 6 deg, and Reynolds numbers of 0.6, 2.0, and 3.7 x one million. The phase-change coating technique was used to obtain heat transfer data. Information received from these tests will be instrumental in performing thermal protection systems studies and vehicle aerodynamic design.

Connor, L. E.↗

NASA NTRS1975

Analytical comparison of hypersonic flight and wind tunnel viscous/inviscid flow fields

Flow fields were computed about blunted, 0.524 and 0.698 radians, cone configurations to assess the effects of nonequilibrium chemistry on the flow field geometry, boundary layer edge conditions, boundary layer profiles, and heat transfer and skin friction. Analyses were conducted at typical space shuttle entry conditions for both laminar and turbulent boundary layer flow. In these calculations, a wall temperature of 1365 K (2000 F) was assumed. The viscous computer program used in this investigation was a modification of the Blottner non-similar viscous code which incorporated a turbulent eddy viscosity model after Cebeci. The results were compared with equivalent calculations for similar (scaled) configurations at typical wind tunnel conditions. Wind tunnel test gases included air, nitrogen, CF4 and helium. The viscous computer program used for wind tunnel conditions was the Cebeci turbulent non-similar computer code.

Fivel, H. J.↗

NASA NTRS1981

Advanced supersonic transport propulsion and configuration technology improvements

This paper presents the results of recent Douglas Aircraft Company integration studies for an advanced supersonic transport. The studies include technology improvements such as superplastic formed and diffusion-bonded titanium sandwich primary structure, composite secondary structure, bicone engine inlet, improved mechanical suppressors based on flight test data, improved aerodynamic efficiency based on wind tunnel test data, and updated performance for both variable-cycle and low-bypass-ratio engines. Technology development requirements for an economically viable and environmentally acceptable advanced supersonic transport are defined through these studies. A new Douglas Aircraft Company baseline supersonic transport designed to carry 350 passengers is defined for cost comparisons.

Rowe, W. T.↗

NASA NTRS1986

Lateral and longitudinal aerodynamic stability and control parameters of the basic vortex flap research aircraft as determined from flight test data

The aerodynamics of the basic F-106B were determined at selected points in the flight envelope. The test aircraft and flight procedures were presented. Aircraft instrumentation and the data system were discussed. The parameter extraction procedure was presented along with a discussion of the test flight results. The results were used to predict the aircraft motions for maneuvers that were not used to determine the vehicle aerodynamics. The control inputs used to maneuver the aircraft to get data for the determination of the aerodynamic parameters were discussed in the flight test procedures. The results from the current flight tests were compared with the results from wind tunnel test of the basic F-106B.

Suit, W. T.↗

NASA NTRS1989

HARP model rotor test at the DNW

Data from a test of a dynamically scaled model of the Hughes Advanced Rotor Program (HARP) bearingless model main rotor and 369K tail rotor are reported. The history of the HARP program and its goals are reviewed, and the main and tail rotor models are described. The test facilities and instrumentation are described, and wind tunnel test data are presented on hover, forward flight performance, and blade-vortex interaction. Performance data, acoustic data, and dynamic data from near field/far field and shear layer studies are presented.

Dawson, Seth↗

NASA NTRS1993

Instrumentation and telemetry systems for free-flight drop model testing

This paper presents instrumentation and telemetry system techniques used in free-flight research drop model testing at the NASA Langley Research Center. The free-flight drop model test technique is used to conduct flight dynamics research of high performance aircraft using dynamically scaled models. The free-flight drop model flight testing supplements research using computer analysis and wind tunnel testing. The drop models are scaled to approximately 20 percent of the size of the actual aircraft. This paper presents an introduction to the Free-Flight Drop Model Program which is followed by a description of the current instrumentation and telemetry systems used at the NASA Langley Research Center, Plum Tree Test Site. The paper describes three telemetry downlinks used to acquire the data, video, and radar tracking information from the model. Also described are two telemetry uplinks, one used to fly the model employing a ground-based flight control computer and a second to activate commands for visual tracking and parachute recovery of the model. The paper concludes with a discussion of free-flight drop model instrumentation and telemetry system development currently in progress for future drop model projects at the NASA Langley Research Center.

Hyde, Charles R.↗

NASA NTRS1923

Aeronautic Instruments. Section III : Aircraft Speed Instruments

Part 1 contains a discussion and description of the various types of air speed measuring instruments. The authors then give general specifications and performance requirements with the results of tests on air speed indicators at the Bureau of Standards. Part 2 reports methods and laboratory apparatus used at the Bureau of Standards to make static tests. Methods are also given of combining wind tunnel tests with static tests. Consideration is also given to free flight tests. Part 3 discusses the problem of finding suitable methods for the purpose of measuring the speed of aircraft relative to the ground.

Hunt, Franklin L↗

NASA NTRS2007

Ares Launch Vehicles Overview: Space Access Society

America is returning to the Moon in preparation for the first human footprint on Mars, guided by the U.S. Vision for Space Exploration. This presentation will discuss NASA's mission, the reasons for returning to the Moon and going to Mars, and how NASA will accomplish that mission in ways that promote leadership in space and economic expansion on the new frontier. The primary goals of the Vision for Space Exploration are to finish the International Space Station, retire the Space Shuttle, and build the new spacecraft needed to return people to the Moon and go to Mars. The Vision commits NASA and the nation to an agenda of exploration that also includes robotic exploration and technology development, while building on lessons learned over 50 years of hard-won experience. NASA is building on common hardware, shared knowledge, and unique experience derived from the Apollo Saturn, Space Shuttle, and contemporary commercial launch vehicle programs. The journeys to the Moon and Mars will require a variety of vehicles, including the Ares I Crew Launch Vehicle, which transports the Orion Crew Exploration Vehicle, and the Ares V Cargo Launch Vehicle, which transports the Lunar Surface Access Module. The architecture for the lunar missions will use one launch to ferry the crew into orbit, where it will rendezvous with the Lunar Module in the Earth Departure Stage, which will then propel the combination into lunar orbit. The imperative to explore space with the combination of astronauts and robots will be the impetus for inventions such as solar power and water and waste recycling. This next chapter in NASA's history promises to write the next chapter in American history, as well. It will require this nation to provide the talent to develop tools, machines, materials, processes, technologies, and capabilities that can benefit nearly all aspects of life on Earth. Roles and responsibilities are shared between a nationwide Government and industry team. The Exploration Launch Projects Office at the Marshall Space Flight Center manages the design, development, testing, and evaluation of both vehicles and serves as lead systems integrator. A little over a year after it was chartered, the Exploration Launch Projects team is testing engine components, refining vehicle designs, performing wind tunnel tests, and building hardware for the first flight test of Ares I-X, scheduled for spring 2009. The Exploration Launch Projects team conducted the Ares I System Requirements Review (SRR) at the end of 2006. In Ares' first year, extensive trade studies and evaluations were conducted to refine the design initially recommended by the Exploration Systems Architecture Study, conceptual designs were analyzed for fitness, and the contractual framework was assembled to enable a development effort unparalleled in American space flight since the Space Shuttle. Now, the project turns its focus to the Preliminary Design Review (PDR), scheduled for 2008. Taking into consideration the findings of the SRR, the design of the Ares I is being tightened and refined to meet the safety, operability, reliability, and affordability goals outlined by the Constellation Program. The Ares V is in the early design stage, focusing its activities on requirements validation and ways to develop this heavy-lift system so that synergistic hardware commonality between it and the Ares I can reduce the operational footprint and foster sustained exploration across the decades ahead.

Cook, Steve↗

NASA NTRS2007

Human Space Exploration: The Moon, Mars, and Beyond

America is returning to the Moon in preparation for the first human footprint on Mars, guided by the U.S. Vision for Space Exploration. This presentation will discuss NASA's mission, the reasons for returning to the Moon and going to Mars, and how NASA will accomplish that mission in ways that promote leadership in space and economic expansion on the new frontier. The primary goals of the Vision for Space Exploration are to finish the International Space Station, retire the Space Shuttle, and build the new spacecraft needed, to return people to the Moon and go to Mars. The Vision commits NASA and the nation to an agenda of exploration that also includes robotic exploration and technology development, while building on lessons learned over 50 years of hard-won experience. Why the Moon? Many questions about the Moon's potential resources and how its history is linked to that of Earth were spurred by the brief Apollo explorations of the 1960s and 1970s. This new venture will carry more explorers to more diverse landing sites with more capable tools and equipment for extended expeditions. The Moon also will serve as a training ground before embarking on the longer, more difficult trip to Mars. NASA plans to build a lunar outpost at one of the lunar poles, learn to live off the land, and reduce dePendence on Earth for longer missions. America needs to extend its ability to survive in hostile environments close to our home planet before astronauts will reach Mars, a planet very much like Earth. NASA has worked with scientists to define lunar exploration goals and is addressing the opportunities for a range of scientific study on Mars. In order to reach the Moon and Mars within a lifetime and within budget, NASA is building on common hardware, shared knowledge, and unique experience derived from the Apollo Saturn, Space Shuttle and contemporary commercial launch vehicle programs. The journeys to the Moon and Mars will require a variety of vehicles, including the Ares I Crew Launch Vehicle, which transports the Orion Crew Exploration Vehicle, and the Ares V Cargo Launch Vehicle, which transports the Lunar Surface Access Module. The architecture for the lunar missions will use one launch to ferry the crew into orbit, where it will rendezvous with the Lunar Module in the Earth Departure Stage, which will then propel the combination into lunar orbit. The imperative to explore space with the combination of astronauts and robots will be the impetus for inventions such as solar power and water and waste recycling. This next chapter in NASA's history promises to write the next chapter in American history, as well. It will require this nation to provide the talent to develop tools, machines, materials, processes, technologies, and capabilities that can benefit nearly all aspects of life on Earth. Roles and responsibilities are shared between a nationwide Government and industry team. The Exploration Launch Projects Office at the Marshall Space Flight Center manages the design, development, testing, and evaluation of both vehicles and serves as lead systems integrator. A little over a year after it was chartered, the Exploration Launch Projects team is testing engine components, refining vehicle designs, performing wind tunnel tests, and building hardware for the first flight test of Ares I-l, scheduled for spring 2009. The U.S. Vision for Space Exploration lays out a roadmap for a long-term venture of discovery. This endeavor will inspire and attract the best and brightest students to power this nation successfully to the Moon, Mars, and beyond. If one equates the value proposition for space with simple dollars and cents, the potential of the new space economy is tremendous, from orbital space delivery services for the International Space Station to mining and solar energy collection on the Moon and asteroids. The Vision for Space Exploration is fundamentally about bringing the resources of the solar system within the economic sphere of humaind. Given the immense size of our solar system, the amount of available material and energy within it present an enormous economic opportunity.

Sexton, Jeffrey D.↗

NASA NTRS2007

Launching to the Moon, Mars, and Beyond

Sumrall, John P.↗

NASA NTRS2016

Quantification of the Uncertainties for the Space Launch System Liftoff/Transition and Ascent Databases

A detailed description of the uncertainty quantification process for the Space Launch System Block 1 vehicle configuration liftoff/transition and ascent 6-Degree-of-Freedom (DOF) aerodynamic databases is presented. These databases were constructed from wind tunnel test data acquired in the NASA Langley Research Center 14- by 22-Foot Subsonic Wind Tunnel and the Boeing Polysonic Wind Tunnel in St. Louis, MO, respectively. The major sources of error for these databases were experimental error and database modeling errors.

Favaregh, Amber L.↗