Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

The effects of varying surface roughness on aerodynamic and aeolian processses

The investigation of aeolian processes on Earth and Mars using wind tunnel simulations is described. The effect of variations in surface roughness on aerodynamic and aeolian processes was examined. Friction velocity ratios, wind friction threshold speeds, particle flux, and total flux were determined for various sand depths, degrees of surface roughness, and heights above a pebble bed.

Reding, L. M.↗

Solvent effects on the hydrodeoxygenation of propanoic acid over Pd(111) model surfaces

The effects of liquid water, n-octane, and n-butanol on the hydrodeoxygenation of propanoic acid over Pd(111) model surfaces have been studied from first principles. We developed a microkinetic model for the hydrodeoxygenation and studied the reaction mechanism at a temperature of 473 K. Our model predicts that for all reaction media, decarbonylation pathways are favored over decarboxylation pathways. However, in the presence of polar solvents like water, decarboxylation routes become competitive with decarbonylation routes. The activity of the Pd surface varies as a function of the environment as follows: water > n-butanol > octane ≈ gas phase. Lastly, a sensitivity analysis of our models suggests that both C–OH and C–H bond cleavages control the overall rate of the catalyst in all environments and are likely to be activity descriptors for the hydrodeoxygenation of organic acids.

COSMO↗

Effect of Porosity on Surface Catalytic Efficiency

This paper describes the effect of surface porosity of thermal protection materials on surface catalytic efficiency using test data taken from both arc-jet and side-arm reactor facilities. Relative surface porosity of the samples varied from 6% to 50%. Surface porosity was measured using a flow apparatus and Bernoulli equation. The surface catalytic efficiency of the materials was calculated using aerothermodynamic, and kinetic theories. The catalytic efficiency of the materials are compared at surface temperatures between room temperature and 2500 F. The data are presented in the form of graphs and tables.

Stewart, David A.↗

Effects of Ultrasonic Surface Rolling Parameters on Surface Integrity of TC17 Alloy

The main purpose of this paper was to investigate the effects of different static forces and feed speeds of ultrasonic surface rolling (USR) on the surface integrity of TC17 alloy. Surface roughness, in-depth residual stress, in-depth microhardness, and cross-sectional microstructure of the processed materials were measured and analyzed to get a comprehensive knowledge of the surface characteristics under different conditions. The results indicate that the specimens treated by USR achieve a considerable improvement in surface roughness (R{sub a} 0.04-0.10 μm); meanwhile, the surface morphology is smooth and uniform. Moreover, the surface residual stress and microhardness are greatly improved compared to those of untreated specimen. The maximum compressive residual stress is approximately − 966 MPa at the depth of 300 μm, and the thickness of strengthened layer is about 1000 μm. The material of affected layer experiences plastic deformation in a certain extent. Moreover, the gradient change in microstructure and white layer are also observed on the subsurface layer. It is also concluded from the study that static force has a more significant impact on surface integrity characteristics compared with feed speed.

36 MATERIALS SCIENCE↗

Effect of free surface shape on combined thermocapillary and natural convection

Combined thermocapillary and natural convection in an open square cavity with differentially-heated side walls is studied numerically as well as experimentally. The test fluid is silicone oil with Prandtl number of 105. The shape of fluid-free surface is made either flat or curved to study its effect on the flow. A finite difference scheme to deal with a curved free surface is developed. The experimental results shown agree with the numerical results. With the curved-free surface, the flow and local heat transfer rate are reduced in the corner regions, and a sharp peak in heat transfer rate at the top edge of the cold wall disappears.

Kamotani, Yasuhiro↗

A modeling study of irrigation effects on global surface water and groundwater resources under a changing climate

Abstract This study investigates the effects of irrigation on global water resources by performing and analyzing Community Land Model 4.0 (CLM4) simulations driven by downscaled/bias‐corrected historical simulations and future projections from five General Circulation Models (GCMs). For each climate scenario, three sets of numerical experiments were performed: (1) a CTRL experiment in which all crops are assumed to be rainfed; (2) an IRRIG experiment in which the irrigation module is activated using surface water (SW) to feed irrigation; and (3) a PUMP experiment in which a groundwater pumping scheme coupled with the irrigation module is activated for conjunctive use of surface water and groundwater (GW) for irrigation. The parameters associated with irrigation and groundwater pumping are calibrated based on a global inventory of census‐based water use compiled by the Food and Agricultural Organization (FAO). Our results suggest that irrigation could lead to two major effects: SW (GW) depletion in regions with irrigation primarily fed by SW (GW), respectively. Furthermore, irrigation depending primarily on SW tends to have larger impacts on low‐flow than high‐flow conditions, suggesting increased vulnerability to drought. By the end of the 21st century, combined effect of increased irrigation water demand and amplified temporal‐spatial variability of water supply may lead to severe local water scarcity for irrigation. Regionally, irrigation has the potential to aggravate/alleviate climate‐induced changes of SW/GW although such effects are negligible when averaged globally. Our study highlights the need to account for irrigation effects and sources in assessing regional climate change impacts.

54 ENVIRONMENTAL SCIENCES↗

Effect of Ion Escape Velocity and Conversion Surface Material on H- Production

According to generally accepted models surface production of negative ions depends on ion escape velocity and work function of the surface. We have conducted an experimental study addressing the role of the ion escape velocity on H- production. A converter-type ion source at Los Alamos Neutron Science Center was employed for the experiment. The ion escape velocity was affected by varying the bias voltage of the converter electrode. It was observed that due to enhanced stripping of H- no direct gain of extracted beam current can be achieved by increasing the converter voltage. The conversion efficiency of H- was observed to vary with converter voltage and follow the existing theories in qualitative manner. We present calculations predicting relative H- yields from different cesiated surfaces with comparison to experimental observations from different types of H- ion sources. Utilizing materials exhibiting negative electron affinity and exposed to UV-light is considered for Cesium-free H-/D- production.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Helium effects on the surface and subsurface evolutions in single-crystalline tungsten

Tungsten (W) has been perceived as one of the most promising plasma facing materials (PFMs) for future fusion reactors. In the past decade, its behavior under irradiation and helium (He) plasma interaction has been extensively studied. However, some key knowledge gaps still exist, such as the influence of crystallographic orientation on the surface and subsurface evolutions. In this work, we focus on the He ion-beam irradiation damage effects in mirror-polished single-crystalline W samples with three different surface planes of {100}, {110} and {111}. Irradiation was performed at room temperature using 40 keV He+ to a fluence of 1 × 10 16 /cm 2 , followed by thermal desorption spectroscopy (TDS) up to ~1920 K. The microstructures of He-irradiated W before and after TDS heat treatment were characterized by scanning and transmission electron microscopy. Subsurface He bubbles were imaged in all irradiated samples, but newly formed <111>-oriented surface grains and surface blisters were only observed in W {100} and {110} starting orientations. These results reveal that radiation damage, He thermal desorption, and surface/subsurface evolution are all strongly dependent on crystallographic orientation. Underlying physical mechanisms are discussed based on ion channeling effects, He-vacancy interactions, and surface diffusion. In conclusion, these findings provide new insights into He effects in W.

36 MATERIALS SCIENCE↗

Characterization of the Effect of Wing Surface Instrumentation on UAV Airfoil Performance

Recently proposed flight research at NASA Dryden Flight Research Center (DFRC) has prompted study into the aerodynamic effects of modifications made to the surfaces of laminar airfoils. The research is focused on the high-aspect ratio, laminar-flow type wings commonly found on UAVs and other aircraft with a high endurance requirement. A broad range of instrumentation possibilities, such as structural, pressure, and temperature sensing devices may require the alteration of the airfoil outer mold line as part of the installation process. This study attempts to characterize the effect of installing this additiona1 instrumentation on key airfoil performance factors, such as transition location, lift and drag curves, and stall point. In particular, the general case of an airfoil that is channeled in the spanwise direction is considered, and the impact on key performance characteristics is assessed. Particular attention is focused on exploring the limits of channel depth and low-Reynolds number on performance and stall characteristics. To quantify the effect of increased skin friction due to premature transition caused by protruding or recessed instrumentation, two simplified, conservative scenarios are used to consider two potential sources of diaturbance: A) that leading edge alterations would cause linearly expanding areas (triangles) of turbulent flow on both surfaces of the wing upstream of the natural transition point, and B) that a channel or bump on the upper surface would trip turbulent flow across the whole upper surface upstream of the natural transition point. A potentially more important consideration than the skin friction drag increment is the change in overall airfoil performance due to the installation of instrumentation along most of the wingspan. To quantify this effect, 2D CFD simulations of the flow over a representative mid-span airfoil section were conducted in order to assess the change in lift and drag curves for the airfoil in the presence of disturbed flow due to the installed instrumentation. A discussion as to the impact on high-altitude and low-speed operation of this and similar aircraft is provided.

Ratnayake, Nalin A.↗

Surface and implantation effects on p-n junctions

The contribution of the graded region of implanted p-n junctions is analyzed using an exponential profile. Though previously neglected, it was recently shown that this contribution to the saturation current of HgCdTe diodes is significant. Assuming a dominant Auger recombination, an analytical solution to the continuity equation is obtained. An expression for the current generation by the graded region is presented for both ohmic and reflecting boundary conditions. A revised condition for a wide region is derived. When the region is narrow, the current differs drastically from that of the zero-gradient case. The effects of the junction depth and the substrate and surface concentrations on the current are investigated. It is shown that the reverse current does not saturate.

Schacham, Samuel E.↗

The Effects of Fiber Surface Modification and Thermal Aging on Composite Toughness and Its Measurement

A detailed experimental study was conducted to establish the structure-property relationships between elevated temperature aging and fiber-matrix bonding, Mode 2 interlaminar fracture toughness, and failure modes of carbon fiber/PMR-15 composites. The fiber-matrix adhesion was varied by using carbon fibers with different surface treatments. Short beam shear tests were used to quantify the interfacial shear strength afforded by the use of the different fiber surface treatments. The results of the short beam shear tests showed that, for times up to 1000 hr, the aging process caused no changes in the bulk of the three composite materials that would degrade the shear properties of the material. Comparisons between the interlaminar shear strengths (ILSS) measured by the short beam shear tests and the GIIC test results, as measured by the ENF test, indicated that the differences in the surface treatments significantly affected the fracture properties while the effect of the aging process was probably limited to changes at the starter crack tip. The fracture properties changed due to a shift in the fracture from an interfacial failure to a failure within the matrix when the fiber was changed from AU-4 to AS-4 or AS-4G. There appears to be an effect of the fiber/matrix bonding on the thermo-oxidative stability of the composites that were tested. The low bonding afforded by the AU 1 fiber resulted in weight losses about twice those experienced by the AS 1 reinforced composites, the ones with the best TOS.

Bowles, Kenneth J.↗

The Effects of Fiber Surface Modification and Thermal Aging on Composite Toughness And its Measurement

A detailed experimental study was conducted to establish the structure-property relationships between elevated temperature aging and (I) fiber-matrix bonding, (2) Mode II interlaminar fracture toughness, and (3) failure modes of carbon fiber/PMR-15 composites. The fiber-matrix adhesion was varied by using carbon fibers with different surface treatments. Short beam shear tests were used to quantify the interfacial shear strength afforded by the use of the different fiber surface treatments. The results of the short beam shear tests definitely showed that, for aging times up to 1000 hr, the aging process caused no observable changes in the bulk of the three composite materials that---would degrade the shear properties of the material. Comparisons between the interlaminar shear strength (ILSS) measured by the short beam shear tests and the GII c test results, as measured by the ENF test, indicated that the differences in the surface treatments significantly affected the fracture properties while the effect of the aging process was probably limited to changes at the starter crack tip. The fracture properties changed due to a shift in the fracture from an interfacial failure to a failure within the matrix when the fiber was changed from AU-4 to AS-4 or AS-4G. There appears to be an effect of the fiber/matrix bonding on the thermo-oxidative stability of the composites that were tested. The low bonding afforded by the AU-4 fiber resulted in weight losses about twice those experienced by the AS-4 reinforced composites, the ones with the best TOS.

Bowles, Kenneth J.↗

Effect of control surface mass unbalance on the stability of a closed-loop active control system

The effects on stability of inertial forces arising from closed-loop activation of mass-unbalanced control surfaces are studied analytically using inertial energy approach, similar to the aerodynamic energy approach used for flutter suppression. The limitations of a single control surface like a leading-edge (LE) control or a trailing-edge (TE) control are demonstrated and compared to the superior combined LE-TE mass unbalanced system. It is shown that a spanwise section for sensor location can be determined which ensures minimum sensitivity to the mode shapes of the aircraft. It is shown that an LE control exhibits compatibility between inertial stabilization and aerodynamic stabilization, and that a TE control lacks such compatibility. The results of the present work should prove valuable, both for the purpose of flutter suppression using mass unbalanced control surfaces, or for the stabilization of structural modes of large space structures by means of inertial forces.

Nissim, E.↗

Effect of detailed surface geometry on riblet drag reduction performance

A comparison is made of the effect of small changes in v-groove geometry, for several riblet films applicable for drag reduction to commercial transport aircraft, whose nominal v-groove dimension is of the order of 0.002 inch. The films were tested in a water towing-tank facility. The results obtained indicate that small riblet peak geometry variations can result in a deterioration of riblet drag-reduction efficacy of as much as 40 percent, while interriblet valley curvature was found not to be critical to riblet performance.

Walsh, Michael J.↗

Determination of Interfacial Rheological Properties through Microgravity Oscillations of Bubbles and Drops

This report summarizes our derivations of analytical expressions for the frequencies and damping constants for small-amplitude axisymmetric shape oscillations of a liquid drop suspended in an immiscible fluid host in microgravity. In particular, this work addresses large Reynolds number shape oscillations and focuses on the surface rheological effects that arise from the presence of insoluble surfactants at the interface. Parameters characterizing viscous effects from the bulk phases, surface viscous effects, Marangoni effects from the surface advection and diffusion of surfactants, and the Gibbs elasticity are all considered and analyzed to determine the relative importance of each contribution. Supplementing the analytical treatment for small-amplitude oscillations, a numerical boundary integral equation formulation is developed for the study of large-amplittide axisymmetric oscillations of a drop in vacuum. The boundary integral formulation is an extension of classical potential flow theory and approximately accounts for viscous effects in the bulk fluid as well as the surface viscous and Marangoni effects resulting from an insoluble surfactant contaminating the interface. Theoretical and numerical results are presented for four distinct cases. These, range from the case when the effects of the surfactants are 'negligible' to 'large' when compared to the viscous effects in the bulk phases. The feasibility of the non-contact measurement of the surface parameters, using experimental observations for the oscillation frequencies and damping constants of drops and bubbles, is discussed.

Nadim, Ali↗

Effect of Impurities on the Oxygen Adsorption Properties on the NiTi(110) Surface

The effect of 3d–5d elements on the oxygen adsorption energy on the NiTi(110) surface has been studied by the projector augmented-waves method within density functional theory. It is shown that almost all elements, except for a few elements of the end of d periods, lead to an increase in the adsorption energy if they substitute for nickel. On the contrary, the substitutional impurities in the titanium sublattice lower this energy. Based on the analysis of the electronic characteristics of the surface with impurities, it has been found that an increase/decrease in the oxygen adsorption energy on NiTi(110) correlates with a change in the ionic contribution to the mechanism of oxygen bonding with the surface.

36 MATERIALS SCIENCE↗