Results for “regularity” — Page 78

DOE OSTI2021

High-Temperature Multi-Process Sensor Development for a PC-Fired Unit

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2022

Real-time sensor measurements to evaluate impacts of load cycling on high-temperature fire-side corrosion in a PC boiler

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2021

High-Temperature Multi-Process Sensor Development and Demonstration at Coalfired Power Plants

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2022

Full-scale Demonstration of Multi-process Sensor at a Cycling PC-fired Boiler

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2023

National Solar Jobs Accelerator (Final Technical Report (FTR))

The aptitudes and experiences gained through military service—such as dynamic leadership, teamwork and critical thinking skills, technical specialization, and a mission-completion work ethic—make veterans exceptional candidates for a wide range of solar energy careers. The solar industry offers a highly collaborative and purpose-driven work environment that resonates with service members and veterans looking to rise to their next challenge, and solar employers are eager to tap into this valuable talent pool. From October 2019 - February 2023, The National Solar Jobs Accelerator (publicly the Solar Ready Vets Network TM (SRV Network; SRVN)) enhanced and streamlined options for military service members and veterans to pursue solar training, certification, and employment, while advancing solar employers’ efforts and capacity to invest in military talent as part of a long-term workforce development strategy. The SRVN was led by the Interstate Renewable Energy Council (IREC) in partnership with the Solar Energy Industries Association (SEIA), the US Chamber of Commerce Foundation’s Hiring Our Heroes program (HOH) and the North American Board of Certified Energy Practitioners (NABCEP). Through several direct-impact and indirect, high-impact capacity building initiatives aligned with six key objectives, the SRV Network strengthened solar career pathways, and promoted increased representation of military talent across all levels and sectors of the solar workforce. A work-based learning Corporate Fellowship model connected transitioning service members with on-the-job experience in leadership roles with solar employers nationwide. The project advanced broader veteran recruitment and talent development by expanding GI Bill eligibility and streamlining veterans’ pathways for solar training and credentialing, supported direct connections to jobs with top solar employers, and led coordination among key education and industry partners to advance registered apprenticeships aligned with solar career pathways. To ensure that the project best served the needs of all stakeholders, an Advisory Committee of military-connected solar professionals, solar employers, and training providers met biannually to guide project activities and sustainability plans. The project team engaged the broader “SRV Network” (comprised of over 2,000 veterans, employers and training organizations) through regular newsletters and targeted outreach to share resources, hiring fairs, webinars, and other opportunities for engagement. The work done under this award builds on the previous iterations of the Department of Energy’s Solar Ready Vets ® program. As the solar industry continues to grow rapidly over the next decade, the military community will continue to be a highly valuable source of talent. The relationships established and work accomplished through this project will have an enduring positive impact well beyond the funding period.

14 SOLAR ENERGY↗

DOE OSTI2023

Comparing Occupant Light Exposure in Factory and Office Spaces

There is an increasing desire to provide healthy workplace environments that better serve people while minimizing the impact on the planet. Building recommendations help designers to incorporate the latest research and best practices, but translating research studies conducted in different settings to broader recommendations is challenging. This is particularly true for lighting, with researchers continuing to learn more about circadian, neuroendocrine, and neurobehavioral responses to light. The recommendations are regularly adjusting to incorporate the latest research as well as feedback from practitioners implementing these recommendations. There remains a need to better document the actual light exposure that people experience over the course of a day and across seasons, so that researchers can better understand the influence of light on people and recommendations can be refined. Thankfully, advances in sensor technology are making this more possible than ever. PNNL collaborated with ETC Inc. to understand actual occupant light exposure in factory and office spaces at ETC’s Headquarters in Middleton, WI. The primary building at ETC headquarters opened in 2004 and houses approximately 800 employees that contribute to central business functions, customer support, research and development, as well as the company’s primary 60,000 ft2 manufacturing facility. Vertical light exposure measurements including electric light and daylight were recorded in factory, research and development, and office work areas at occupant eye height. This document will focus on lighting measurements collected in six factory and office locations across work location, season, and time of day. Ultimately, detailed lighting measurements can be coupled with employee surveys to support development of satisfactory work environments.

42 ENGINEERING↗

DOE OSTI2024

Spread Spectrum Time Domain Reflectivity for String Monitoring in PV Power Plants (Final Technical Report)

This final report describes the methods and results of applying Spread Spectrum Time Domain Reflectivity (SSTDR) for String Monitoring in PV Power Plants for DE-EE0008169. The project created a new system for both detecting and locating electrical faults in photovoltaic systems. In this work, we address photovoltaic electric faults that are both common and costly. Based on interviews with photovoltaic power plant owners, operators, and maintainers, three types of faults are common and of significant interest: disconnects, ground faults, and arc faults. Disconnects can originate from many sources. They are often due to everyday events, such as lawnmowing (accidentally running over a cable), animals eating through the cables, or degradation that occurs over time due to corrosion or general degradation. Ground faults occur when the cables (for example, due to frayed insolation) connect to the ground, relaying current into the ground. These faults are particularly problematic since the ground faults are often intermittent. That is, ground faults commonly appear during rain storms due to a change in soil conductivity and then disappear when the rain ends. This makes the ground fault difficult to find because while current systems can detect the overall change in voltage and current associated with a ground fault, technicians are necessary to locate the fault. As a result, ground faults may disappear before the technician arrives at the power plant. Hence, locating and fixing ground faults often require multiple trips. We also study arc faults, which can result when nearby conductors create an arc of electrical current through the air. While less common, arc faults can be extremely dangerous. The energetic electrical arc can cause fires and destroy equipment, costing significant damage. Overall all three types of faults cost owners and operators money, either from the destruction of equipment or from technician time. Furthermore, while devices exist for detecting ground faults (ground fault circuit interrupters) and arc faults (arc fault circuit interrupter), these systems only search patterns of electrical current that correspond to each fault. This information cannot be used to locate the fault. In addition, these protection systems experience nuisance trips due to nearby electromagnetic interference, such as from a lawn mower or other motors that produce significant amounts of electromagnetic radiation. Hence, the overall goal of this project is to create an SSTDR tool that provides photovoltaic power plants with more reliable fault detection in addition to the localization of faults. SSTDR works by transmitting electrical signals into the photovoltaic string. Those signals reflect from impedance discontinuities (i.e., disconnects, ground faults, and arc faults). These faults are then detected by measuring the presence of a reflection at the SSTDR and can be located by identifying the location of that reflection in time. In addition, unlike current protection systems, these systems do not experience nuisance trips since their low amplitude, high frequency, and coded signal can by analyzed without interference from the regular operational voltage on the photovoltaic string.

14 SOLAR ENERGY↗

DOE OSTI2024

Solar Photovoltaics and Land-Based Wind Technical Potential and Supply Curves for the Contiguous United States (2023 Edition)

Estimates of the potential of renewable energy are essential for understanding how we can decarbonize our electric grid and economy. They provide key data for policymakers, land managers, and energy modelers by defining the quantity, quality, and cost of renewable resources. However, estimating renewable energy potential is challenging and requires frequent updates because of rapid advances in technology, cost reductions, and uncertainty about developable land that are due to social, regulatory, and environmental factors. Additionally, the complex processes involved in renewable energy development require regular reviews of methods and assumptions, which can also impact our understanding of renewable potential. In this, the 2023 edition of this annual report, we present new estimates of the technical potential for land-based wind and solar photovoltaics (PV) for the contiguous United States (CONUS). We also provide cost estimates for the available resources, presenting representative supply curves that can be used in downstream modeling and analysis. Additionally, we introduce the new methodologies used to estimate wind capacity, wind energy losses, transmission cost and representation, updated technology cost and design, and scenarios of siting constraints designed to help bound the uncertainty of renewable potential.

14 SOLAR ENERGY↗

DOE OSTI2023

The Energy and Operational Impacts of Using 0-10V Control for LED Streetlights

LED lighting is becoming widely adopted and displacing most traditional lighting technologies. However, the traditional methods used to control light sources have not seen similar displacement. Lighting systems have historically utilized either a proprietary control method, or one of a handful of standardized methods (e.g., 0-10V, DALI, DMX512). The utility and market success of the standardized methods has been limited for a variety of reasons. Analog 0-10V methods have long been popular due to their simplicity and low cost of implementation and are presently the most commonly available control interface for indoor and outdoor LED products in North America. The emergence of “connected lighting systems” with more modern network interfaces and luminaire-level sensors and intelligence was anticipated by many to mark the beginning of the end of analog control. However, 0-10V interfaces continue to be prevalent with these more “digital” systems. The use of 0-10V methods has significant tradeoffs. 0-10V standards have historically not explicitly defined the relationship between the luminaire input control signal and output luminous flux for the full control signal range. As a result, it is difficult to predict relative luminaire light output and input power at any particular control voltage, and in practice the performance across LED drivers and the luminaires power is inconsistent. While this inconsistency has long been acknowledged by experts in the field, it is not accounted for in standard practice deployment, and end-users continue to regularly see unexpected and undesirable performance. It is hoped that the results from this study will help the lighting industry and standards developing organizations better understand and possibly resolve the shortcomings of 0-10V products, and consider what is best for the industry – additional incremental improvements to this fundamentally limited analog technology, or fully moving on to existing digital approaches, such as DALI D4i, that deliver accurate and consistent dimming performance across all luminaires in the system and thus guarantee the delivery of expected light levels, and energy and cost savings. Recommendations consistent with these goals are made to lighting and driver manufacturers, lighting software developers, standard developing organizations, and system designers and specifiers.

0-10V↗

DOE OSTI2024

Approximate Entropy Analysis for Nonlinear Beam Dynamics

In this paper, we applied an approximate entropy (ApEn) analysis to nonlinear beam dynamics. Due to the presence of strong nonlinear magnets, the degree of chaos in beam motion gradually increases proportionally with its amplitude. Such chaos can be quantitatively characterized with ApEn of beam turn-by-turn readings. ApEn analysis is a technique used to quantify the amount of regularity and the unpredictability of fluctuations with respect to time-series data. The ApEn, when applied as a chaos indicator, can then be used for nonlinear lattice optimization and analysis. The National Synchrotron Light Source II (NSLS-II) electron storage ring lattice was used as an example of a real-world application of our technique.

43 PARTICLE ACCELERATORS↗

DOE OSTI2024

Saving Energy, Saving Money [Slides]

Make sure you have CO detectors installed; Test batteries regularly; Have your furnace serviced annually; Don’t use grills or generators indoors.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2024

Developing Platinum-Group-Metal-Free Catalysts for Oxygen Reduction Reaction in Acid: Beyond the Single Metal Site

This project is to develop M (x) -N-C catalysts with dense multiple metal center (MMC) sites to meet the DOE 2025 activity target of 0.044 mA/cm 2 at 0.9 V IR-free ., as well as other goals such as durability. We have made important contributions to both catalyst development and fundamental understandings of the active sites in M-N-C catalysts in this project. We successfully made M (x) -N-C catalysts with some multiple metal center (MMC) sites by combining ionothermal carbonization with chemical vapor deposition (CVD). These catalysts, however, are not as active as the most active single-atom Fe-N-C catalysts made by the similar CVD process, owing likely to the low site density and the presence of inorganic Fe species such as iron carbides and nanoparticles. The most significant accomplishments we achieved in this project are: (1) we unraveled the formation pathway of Fe-N 4 sites during pyrolysis step-by-step and identified the trans-metalation mechanism, in collaboration with Deborah Myers and her colleagues at Argonne National Laboratory (ANL); (2) inspired by this finding, we pioneered the CVD synthesis of M-N-C catalysts (M = Mn, Fe, and Co), in which the Fe-N-C catalyst by CVD demonstrated an ORR activity of 33 mA/cm 2 at 0.9 V in H 2 -O 2 proton exchange membrane fuel cells (PEMFCs), very close to the ultimate goal of 35 mA/cm 2 of our project. This catalyst is the first Fe-N-C catalyst that contains only D1 sites without the D2 sites; whereas D1 and D2 sites have been always identified by Mossbauer in previous Fe-N-C catalysts. This finding helps to understand what the D1 and D2 sites are and their roles in catalyzing the ORR. (3) by improving the mass transport of the carbon matrix prior to the CVD process, the revised Fe-N-C catalyst made by CVD delivered a maximum power density of 0.53 W/cm 2 in H 2 -air PEMFCs. The improvement strategy was partly inspired by the computational modeling work by Adam Weber from LBNL, the Co-PI of this project, by developing, coding, and exercising a continuum level model of transport phenomena within a PGM-free catalyst layer. The model demonstrated that local resistances combined with limited site density of the PGM-free catalyst can result in limiting currents and poor polarization performance. The model also gave design guidance for impact of ECSA and overall catalyst-layer thickness. However, both Fe-N-C and Co-N-C catalysts developed by CVD showed poor durability in PEMFCS, in comparison with the traditional M-N-C catalysts synthesized via regular pyrolysis process. Consequently, we did not achieve the proposed durability targets. Despite so, we believe the FeNC-CVD catalysts with the poor durability and D1 sites only provides an excellent platform to understand the degradation mechanism of Fe-N-C in PEMFCs, the most important challenge in the development of M-N-C catalysts.

08 HYDROGEN↗

DOE OSTI2024

An Autonomous Critical Data Extrapolator for the AGN-201m

Nuclear nonproliferation serves as a key goal, being undertaken by the International Atomic Energy Agency (IAEA). To recognize proliferation there are two pathways that states, who intend to use nuclear material for malicious purposes can take, diversion can misuse. Diversion is when fissile nuclear material is declared to the IAEA for non-weapon purposes, but then covertly removed. If the source of nuclear material, that is not declared and not fissionable, is placed inside the reactor core to create fissile material used to create weapons then the state is using the second pathway of proliferation, misuse. With the emerging development in areas of simulation and machine learning the creation of virtual models of reactor systems, digital twins, serve as a potential method to identify proliferation through detecting anomalous behavior in the reactor. A digital twin for a physical nuclear reactor has never been developed, as digital twins serve as an emerging technology. To investigate the process for development and use of a digital twin for a nuclear reactor Idaho State University’s AGN-201m serves as the nuclear reactor used for development of this digital twin. A data acquisition system has been installed to the reactor system allowing for the transfer of collected data from a reactor operation to Idaho National Laboratory’s Deeplynx data warehouse. When utilizing data to train reactor physics and machine learning models, a significant challenge encountered is the initial state of the data. Nuclear proliferation will have the capacity to be detected when the reactor immediately starts up, nor will it occur after the reactor shuts down. Generally, it will be detected when the reactor is operating at some desired power over a sufficient period for that specific reactor design. For the AGN-201m this will be when the reactor is critical (generally 1 mW or above) for a timespan that is within or less than the range of a regular business day. Datasets sent to Deeplynx have had to be manually cut to when the reactor is critical based on plots of power levels. This method is inefficient and laborious, especially when using multiple datasets at once to train a model. To provide a more streamlined approach an automated critical data extrapolator is developed, with capabilities of recognizing when the reactor operation first reaches criticality, and when the reactor undergoes a SCRAM and is shutdown.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2024

Southwest Regional Partnership on Carbon Sequestration (Phase III) Underground Source of Drinking Water Monitoring at the Farnsworth Unit

The Ogallala aquifer is identified as the only underground source of drinking water (USDW) aquifer in the vicinity of the FWU. Throughout the span of the SWP project at the FWU, groundwater samples from the Ogallala Aquifer were collected and analyzed on a regular basis to obtain information that reflects the water quality baseline and any potential leakage, and to facilitate effective simulations and risk assessment. To date, hundreds of samples have been collected and tested. The water analysis results suggest that the Ogallala groundwater quality maintains stable and potable, and no leakage is indicated by these data.

42 ENGINEERING↗

DOE OSTI2023

Domain Aware Deep-learning Algorithms Integrated with Scientific-computing Technologies (DADAIST)

This technical report summarized the contribution of the DADAIST project funded by the Data Model Convergence Initiative via the Laboratory Directed Research and Development (LDRD) investments at Pacific Northwest National Laboratory (PNNL). Specifically, we report the development of the NeuroMANCER (Neural Modules with Adaptive Nonlinear Constraints and Efficient Regularizations), a new open-source Scientific Machine Learning library for formulating and solving parametric constrained optimization problems, physics-informed system identification, and parametric optimal control problems. NeuroMANCER is using differentiable programming to combine modern data-driven models and optimization modeling language into a coherent algorithmic and software framework. NeuroMANCER is a Pytorch-based framework and adopts much of its philosophy focused on research and development, rapid prototyping, and streamlined deployment. Strong emphasis is given to extensibility, interoperability with the PyTorch ecosystem, and quick adaptability to custom domain problems. Neuromancer repository contains a comprehensive library of differentiable modules, including custom activation functions, matrix factorizations, deep learning architectures, neural differential equations, differential equation solvers, implicit layers such as iterative solvers, high-level API for symbolic expressions, API for modeling and control of dynamical systems, and extensive set of tutorial code examples in the form of python scripts and jupyter notebooks.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

Gamma Source Verification for GAMSRC and GAMSOR

Nuclear reactors that rely upon the fission reaction have two modes of thermal energy deposition in the reactor system: neutron absorption and gamma absorption. The gamma rays are typically generated by neutron capture reactions or during the fission process which means the primary driver of energy production is of course the neutron interactions. The GAMSOR program was first built in the mid 1980s to properly account for the gamma heating in an operating reactor core on core internals. The GAMSOR code is sequence of DIF3D calculations to compute the neutron and gamma flux and combine them to define both the neutron and gamma heating throughout the modeled domain. The goal of this manuscript is to present the software verification of GAMSOR. The first step of the GAMSOR sequence of calculations involves of a modified version of DIF3D (called DIF3D-GAMSOR) which generates a gamma source distribution for the follow-on DIF3D gamma transport calculation (step 2). This modified version of DIF3D increases the burden of maintenance and verification work on GAMSOR as one must reverify the DIF3D capabilities which is undesirable. Because the calculation of the gamma source is the only unique aspect of GAMSOR beyond the regular DIF3D capabilities, that part was put in a standalone code called GAMSRC such that one can use the verified DIF3D code in step 1 followed by GAMSRC to carry out the same GAMSOR calculation step. As a consequence, this manuscript is focused on verification of the gamma source files generated by GAMSRC. The verification of the modified version of DIF3D (DIF3D-GAMSOR) will be done less rigorously in that it will be verified that it produces the same output that GAMSRC does and thus GAMSRC is equivalent to GAMSOR on the problems studied here. Hand calculations and independent numerical calculations of the gamma source generation are used for the verification work. This work follows the same methodology of GAMSRC. As expected, the results agree well with those calculated by GAMSRC as will be shown.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Hydrodynamic Test Requirements Process Improvements

Hydrodynamic testing at Los Alamos National Laboratory would benefit from a process improvement for the requirements process. Cameo was used as a digital solution for requirements management to allow Lead Engineers to track requirements more effectively. This was identified as a process improvement throughout this Capstone project. This report includes a project proposal, business case, literature review, methodology, project plan, data analysis, decision-making report, financial analysis report, discussion, and conclusion. Initially, this project focused on figuring out a solution for the hydrotest requirement process improvements. The scope narrowed to focus on the use of Cameo for requirement capture and management. During this Capstone, four tests had digital models produced for requirements management in Cameo. The initial model was the baseline, with core requirements used across the tests. Commonalities in tests were used and the core requirements allowed for process efficiencies. In the data analysis, it was seen that overall, the implementation of using Cameo for requirements resulted in a decreasing trend for both schedule and normalized cost. Tests have different complexity levels which is also a factor in how long the requirements process will take. Additional data is needed to continue analyzing process improvements. Through decisionmaking and financial analysis, the recommendation was to use Cameo for requirements process improvement. Multiple experts provided feedback for requirements that were then captured within models. Numerous tangible and intangible benefits were identified with this process improvement. For return on investment, the metric of success was schedule reduction, which was overall seen. Four tests were analyzed, so future analysis will be needed. There is also not a great financial risk because the main cost would be purchasing more licenses. Individuals must generate requirements whether using this software or not. Overall, training is needed to help improve the skillsets of Lead Engineers but is already being supported on a regular frequency. A desktop guide was started associated with explaining the process, however, it is a work in progress. The team plans on adding additional information in the digital models to help status when requirements are met using verification methods and artifacts. From working on this project an improved understanding of Cameo and requirements was the result. There are future opportunities to extend the usage for requirements management and progress will continue after this project.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2024

QUIC-DEPDOSE: Software tools to prepare for and respond to nuclear emergencies

QUIC-DEPDOSE is a software application that calculates radiation doses from inhalation of radionuclides downstream from an atmospheric radiological release. Unlike other radiological modeling software, QUIC-DEPDOSE can provide accurate dose information in as little as an hour running on a regular laptop, allowing for use by emergency responders after an accident.

61 RADIATION PROTECTION AND DOSIMETRY↗