Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “particle data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Chemistry of cometary meteoroids from video-tape records of meteor spectra

The chemistry of the cometary meteoroids was studied by closed circuit television observing systems. Vidicon cameras produce basic data on standard video tape and enable the recording of the spectra of faint shower meteors, consequently the chemical study is extended to smaller particles and we have a larger data bank than is available from the more conventional method of recording meteor spectra by photography. The two main problems in using video tape meteor spectrum records are: (1) the video tape recording has a much lower resolution than the photographic technique; (2) video tape is relatively new type of data storage in astronomy and the methods of quantitative photometry have not yet been fully developed in the various fields where video tape is used. The use of the most detailed photographic meteor spectra to calibrate the video tape records and to make positive identification of the more prominent chemical elements appearing in the spectra may solve the low resolution problem. Progress in the development of standard photometric techniques for the analysis of video tape records of meteor spectra is reported.

Millman, P. M.↗
NASA NTRS2003

FAST/Polar Conjunction Study of Field-Aligned Auroral Acceleration and Corresponding Magnetotail Drivers

The discrete aurora results when energized electrons bombard the Earth's atmosphere at high latitudes. This paper examines the physical processes that can cause field-aligned acceleration of plasma particles in the auroral region. A data and theoretical study has been carried out to examine the acceleration mechanisms that operate in the auroral zone and to identi@ the magnetospheric drivers of these acceleration mechanisms. The observations used in the study were collected by the Fast Auroral Snapshot (FAST) and Polar satellites when the two satellites were in approximate magnetic conjunction in the auroral region. During these events FAST was in the middle of the auroral zone and Polar was above the auroral zone in the near-Earth plasma sheet. Polar data were used to determine the conditions in the magnetotail at the time field-aligned acceleration was measured by FAST in the auroral zone. For each of the magnetotail drivers identified in the data study, the physics of field-aligned acceleration in the auroral region was examined using existing theoretical efforts and/or a long-system particle in cell simulation to model the magnetically connected region between the two satellites. Results from the study indicate that there are three main drivers of auroral acceleration: (1) field-aligned currents that lead to quasistatic parallel potential drops (parallel electric fields), (2) earthward flow of high-energy plasma beams from the magnetotail into the auroral zone that lead to quasistatic parallel potential drops, and (3) large-amplitude Alfven waves that propagate into the auroral region from the magnetotail. The events examined thus far confm the previously established invariant latitudinal dependence of the drivers and show a strong dependence on magnetic activity. Alfven waves tend to occur primarily at the poleward edge of the auroral region during more magnetically active times and are correlated with intense electron precipitation. At lower latitudes away from the poleward edge of the auroral zone is the primary field-aligned current region which results in the classical field- aligned acceleration associated with the auroral zone (electrons earthward and ion beams tailward). During times of high magnetic activity, high-energy ion beams originating from the magnetotail are observed within, and overlapping, the regions of primary and return field-aligned current. Along the field lines where the high-energy magnetotail ion beams are located, field-aligned acceleration can occur in the auroral zone leading to precipitating electrons and upwelling ionospheric ion beams. Field-aligned currents are present during both quiet and active times, while the Alfven waves and magnetotail ion beams were observed only during more magnetically active events.

Schriver, D.↗
NASA NTRS1996

Stereo Imaging Velocimetry

Stereo imaging velocimetry (SIV) will permit the collection of quantitative, three-dimensional flow data from any optically transparent fluid that can be seeded with tracer particles. This includes such diverse experiments as the study of multiphase flow, bubble nucleation and migration, pool combustion, and crystal growth. This technique will be useful to the microgravity science community as our investigations of fluid behavior in reduced-gravity environments enhance our knowledge of heat transfer, surface tension, concentration-gradient-driven anomalies, and residual effects from g-jitter. In its proposed configuration, the NASA Lewis Research Center's Stereo Imaging Velocimeter will consist of at least two charged coupled device (CCD) cameras, oriented at some relative angle with respect to each other. The cameras will observe a fluid experiment that has been seeded with tracer particles that are neutrally buoyant to permit accurate flow tracking. Except for the tracer particles, this measurement technique will be nonintrusive. Velocity accuracies will be on the order of 1 to 5 percent of full field. Each camera will make a two-dimensional record of the motion of the seed particles in the observation volume. Three-dimensional data will be obtained by computationally combining the two-dimensional information.

Source record↗
NASA NTRS2001

Retrieval of Polar Stratospheric Cloud Microphysical Properties From Lidar Measurements: Dependence on Particle Shape Assumptions

Knowledge of particle sizes and number densities of polar stratospheric clouds (PSCs) is highly important, because they are critical parameters for the modeling of the ozone chemistry of the stratosphere. In situ measurements of PSC particles are rare. the main instrument for the accumulation of PSC data are lidar systems. Therefore the derivation of some microphysical properties of PSCS from the optical parameters measured by lidars would be highly beneficial for ozone research. Inversion of lidar data obtained in the presence of PSCs formed from crystalline particles type 11 and the various nitric acid tri Ydrrate (NAT) types cannot be easily accomplished, because a suitable scattering theory for small faceted crystals has not been readily available tip to now. As a consequence, the T-matrix method is commonly used for the interpretation of these PSC lidar data. Here the assumption is made that the optical properties of an ensemble of spheroids resemble those of crystalline PSCs, and microphysical properties of the PSC are inferred from the optical signatures of the PSC at two or more wavelengths. The problem with the T-matrix approach is that the assumption of spheroidal instead of faceted particles can lead to dramatically wrong results: Usually cloud particle properties are deduced from analysis of lidar profiles of backscatter ratio and depolarization ratio. The particle contribution to the backscatter ratio is given by the product of the particle number density and the backscattering cross section. The latter is proportional to the value of the particle's scattering phase function at 180 degrees scattering angle. At 180 degrees however, the phase functions of rough, faceted crystals and of spheroids with same maximum dimension differ by a factor of 6. From this it follows that for a PSC consisting of faceted crystals, the particle number density is underestimated by roughly the same factor if spheroidal particles are unrealistically assumed. We are currently developing a retrieval technique for determining the microphysical parameters of crystalline PSCs that takes into account the faceted shape of the PSC particles. This approach utilizes finite-difference time-domain (FDTD) calculations of particle optical properties. The accuracy and the free choice of the shape of the scattering particle make the FDTD technique a promising tool for the inversion of PSC lidar data. A first comparison of FDTD and T-matrix calculations will be presented.

Reichardt, Susanne↗
NASA NTRS1995

Thermal emission from particulate surfaces: A comparison of scattering models with measured spectra

Emissivity spectra of particulate mineral samples are highly dependent on particle size when that size is comparable to the wavelength of light emitted (5-50 micrometers for the midinfrared). Proper geologic interpretation of data from planetary infrared spectrometers will require that these particle size effects be well understood. To address this issue, samples of quartz powders were produced with narrow, well-characterized particle size distributions. Mean particle diameters in these samples ranged from 15 to 227 micrometers. Emission spectra of these powders allow the first detailed comparison of the complex spectral variations with particle size observed in laboratory data with the predictions of radiative transfer models. Four such models are considered here. Hapke's relectance theory (converted to emissivity via Kirchoff's law) is the first model tested. Hapke's more recently published emission theory is also employed. The third model, the 'Mie/Conel' model, uses Mie single scattering with a two-stream approximation for multiple scattering. This model, like the first, is a converted reflec- tance model. Mie scattering assumes particles are both spherical and well separated, which is not true for the quartz powders, but includes diffraction effects. The fourth model uses the Mie solution for single scattering by spheres and inputs those results into the multiple scattering formalism of Hapke's emission theory. The results of the four models are considered in relation to the values of the optical constants n and k. We have grouped these as class 1 (k large), class 2 (k moderate, n is approximately 2), class 3 (k small, n is approximately 2), and class 4 (k small, n is approximately 1). In general, the Mie/Hapke hybrid model does best at predicting variations with grain size. In particular, it predicts changes of the correct pattern, although incorrect magnitude, for class 1 bands, where large increases in emissivity with decreasing grain size are observed. This model also does an excellent job on moderate (class 2) and very weak and intraband (class 3) regions, and correctly predicts the emission maximum and its invariance with grain size near the Christiansen frequency (class 4). The Mie/Hapke hybrid model also has the fewest free parameters of the four models examined, while maintaining the most physical treatment of the radiative transfer. The Mie/Conel model performs as well as the Mie/Hapke hybrid model in strong bands (class 1) but does not accurately model the behavior of moderate (class 2) and very weak (class 3) bands.

Moersch, J. E.↗
DOE OSTI2022

Particle scale impacts on deconstruction energy of pine residues

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on generation of fines that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbon content (minimum carbon specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed residue not meeting both specifications to the conversion reactor. Laboratory data on the impacts of input particle size and moisture content on the exit particle size were received from FCIC Subtask 5.2 from their single particle impact population balance modeling study. Additional throughput and energy consumption data were obtained from FCIC Subtask 5.2 for the same grinder with a 6 mm screen in place. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents in the separated fines had not been analyzed in the laboratory at the time of the model runs, we chose to assume that the ash distributed proportionally with total mass into the overs and unders in the disk screen following grinding. Key takeaways from this Case Study are that it is significantly more cost effective to hammer mill the residue prior to drying, even though the grinder throughput is lower and energy consumption is higher versus drying first before grinding. An effect of dry grinding versus high moisture grinding is the production of higher amounts of fines during dry grinding, leading to significantly more of the ground feedstock being rejected by conversion for being below a minimum particle size. With wet grinding the system is still able to produce more preprocessed feedstock meeting the minimum particle size specification even though the instantaneous throughput is lower than for the case of grinding dry feedstock. Additionally, even without the higher fines production from dry grinding, the status quo would still be more costly than wet grinding because the material is rejected after the drying energy has already been input for the dry grinding case. Finally, significant reductions in drying energy are obtained by drying after grinding, and those reductions are of far greater magnitude than the grinding energy increase.

09 BIOMASS FUELS↗
DOE OSTI2022

Critical Shear Stress for Erosion Under Laminar Jet Flow

Particle erosion is an important process in both natural and manmade environments. For example, in natural environments particle or sediment erosion rates determine the course of rivers, depth of streams, and fate of deltas. The interplay between erosion rates and flow patterns can have dramatic impact on shorelines. Where hydrodynamic jet flows or rip currents change direction, sediments may accumulate or disperse altering the shape of coastlines and the ecosystems and economies that rely on them. In man-made systems, jet flows may be used to mobilize particles from surfaces or within industrial scale mixing tanks. For example, in the nuclear industry, impinging jet mixers may be used to mobilize and suspend sludges at the bottom of waste tanks. In each of these examples, the Shields diagram is useful to determine the conditions under which erosion occurs. This diagram plots the scaled critical shear stress for erosion as a function of the particle size as embedded in particle Reynolds numbers, Archimedes numbers, or their equivalents. Although the data, that carries a large spread, is largely in agreement with mathematical models, for the smallest particles, model predictions diverge from each other and from experimental data. Indeed, there is substantial uncertainty about the Shields diagrams at relatively small particle sizes and flow rates. Here we evaluate critical shear stresses for erosion under laminar jet flow. To date critical shear stresses for erosion, as embodied in Shields diagrams, have largely been developed for turbulent flow both experimental and mathematically. However, curves on the Shields diagrams diverge among various models at lower particle Reynolds numbers. Indeed, how critical shear stresses for erosion develop under fully laminar jet flow conditions (not simply laminar boundary layers under turbulent flow) remains unclear. Here we address this gap, which is particularly important for mobilization of the smallest particles. We find the Shields parameter to be inversely proportional to the particle Reynolds numbers under laminar jet flow conditions similar to turbulent conditions.

critical shear stresses, erosion rates, effective ↗
DOE OSTI2022

Skopi: a simulation package for diffractive imaging of noncrystalline biomolecules

X-ray free-electron lasers (XFELs) have the ability to produce ultra-bright femtosecond X-ray pulses for coherent diffraction imaging of biomolecules. While the development of methods and algorithms for macromolecular crystallography is now mature, XFEL experiments involving aerosolized or solvated biomolecular samples offer new challenges in terms of both experimental design and data processing. Skopi is a simulation package that can generate single-hit diffraction images for reconstruction algorithms, multi-hit diffraction images of aggregated particles for training machine learning classifiers using labeled data, diffraction images of randomly distributed particles for fluctuation X-ray scattering algorithms, and diffraction images of reference and target particles for holographic reconstruction algorithms. Skopi is a resource to aid feasibility studies and advance the development of algorithms for noncrystalline experiments at XFEL facilities.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2002

FAST/Polar Conjunction Study of Field-Aligned Auroral Acceleration and Corresponding Magnetotail Drivers

The discrete aurora results when energized electrons bombard the Earth's atmosphere at high latitudes. This paper examines the physical processes that can cause field-aligned acceleration of plasma particles in the auroral region. A data and theoretical study has been carried out to examine the acceleration mechanisms that operate in the auroral zone and to identity the magnetospheric drivers of these acceleration mechanisms. The observations used in the study were collected by the Fast Auroral SnapshoT (FAST) and Polar satellites when the two satellites were in approximate magnetic conjunction in the auroral region. During these events FAST was in the middle of the auroral zone and Polar was above the auroral zone in the near-Earth plasma sheet. Polar data was used to determine the conditions in the magnetotail at the time field-aligned acceleration was measured by FAST in the auroral zone. For each of the magnetotail drivers identified in the data study, the physics of field-aligned acceleration in the auroral region was examined using existing theoretical efforts and a long-system particle-in-cell simulation to model the magnetically connected region between the two satellites.

Schriver, D.↗
NASA NTRS1988

Confined turbulent fluid-particle flow modeling using multiple-realization particle trajectory schemes

A multiple-realization particle trajectory scheme has been developed and applied to the numerical prediction of confined turbulent fluid-particle flows. The example flows investigated include the vertical pipe upflow experimental data of Tsuji et al. and the experimental data of Leavitt for a coaxial jet flow, comprising a particle-laden central jet and a clean annular jet, into a large recirculation chamber. The results obtained from the numerical scheme agree well with the experimental data, lending confidence to the modeling approach. The multiple-realization particle trajectory turbulent flow modeling scheme is believed to be a more elegant and accurate approach to the extension of single-particle hydrodynamics to dilute multi-particle systems than the more commonly employed two-fluid modeling approach. It is also better able to incorporate additional force items such as lift, virtual mass and Bassett history terms directly into the particle equation of motion as appropriate. This makes it a suitable candidate for particle migration studies and an extension to situations involving liquid particulate phases with possible propulsion applications, such as in spray combustion, follows naturally.

Adeniji-Fashola, A. A.↗
DOE OSTI2024

Angular Dependence of Drell-Yan in the SeaQuest Experiment using Deep Neural Network-Based Reconstruction

The SeaQuest and SpinQuest experiments at Fermilab were designed to probe the internal dynamics of protons and neutrons via the angular dependence of muons created by colliding 120 GeV protons into stationary targets. To do this, it is necessary to translate the detector data into coherent information about the particles detected in the experiment. This dissertation describes the development and implementation of QTracker, a neural network-based algorithm designed to reconstruct muons. The application of QTracker to experimental data yields improved reconstruction of muon tracks, allowing for a more precise investigation of the transverse momentum distributions and angular modulations in the Drell-Yan process. This work highlights the potential of neural network-based methods to advance particle tracking and enhance our understanding of nucleon structure.

Conover, Arthur↗
NASA NTRS1984

The interplanetary scattering mean free path - Collisionless wave-damping effects

The role of dissipation in the scattering of charged particles in the interplanetary medium (IPM) is analyzed to obtain a model for the interplanetary magnetic turbulence spectrum that yields particle free paths (PEP) which agree with observational data. The scattering processes are attributed to waves with small wavelengths intersected by particles with zero pitch angles. The waves, being strongly damped by collisionless cyclotron damping in the ambient thermal plasma, produce reduced scattering and longer MFPs. The model, which includes the damping factor, was used to generate proton propagation maps at kinetic energy levels of under, over, and within the 5 MeV-2 GeV range. The results, when compared with observational data, displayed good agreement. The same held true for the MFP propagation of energetic electrons.

Davila, J. M.↗
DOE OSTI2025

Machine Learning for Predicting Multipactor Susceptibility in Planar RF Structures

Multipactor discharge is a persistent challenge in high-power microwave (HPM) and accelerator systems, where secondary electron avalanches can cause heating, vacuum degradation, and failure. This work presents the first supervised machine learning (ML) framework for multipactor prediction, trained on high-fidelity 3D Particle-in-Cell (PIC) simulation data in planar geometries. The model maps operational, geometric, and material-dependent secondary electron yield (SEY) parameters to the time-averaged electron growth rate, enabling rapid reconstruction of susceptibility charts. Among the models evaluated, tree-based ensemble methods such as Random Forest and Extra Trees demonstrate superior generalization to unseen materials compared to neural networks such as multilayer perceptron (MLP). Performance metrics, including Intersection over Union (IoU), Structural Similarity Index Measure (SSIM), and Pearson correlation, show close agreement with simulation benchmarks. Principal Component Analysis attributes generalization limits to material feature-space disjointedness.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Denoising diffusion models with geometry adaptation for high fidelity calorimeter simulation

Simulation is crucial for all aspects of collider data analysis, but the available computing budget in the High Luminosity LHC era will be severely constrained. Generative machine learning models may act as surrogates to replace physics-based full simulation of particle detectors, and diffusion models have recently emerged as the state of the art for other generative tasks. Here, we introduce CaloDiffusion, a denoising diffusion model trained on the public CaloChallenge datasets to generate calorimeter showers. Our algorithm employs 3D cylindrical convolutions, which take advantage of symmetries of the underlying data representation. To handle irregular detector geometries, we augment the diffusion model with a new geometry latent mapping (GLaM) layer to learn forward and reverse transformations to a regular geometry that is suitable for cylindrical convolutions. The showers generated by our approach are nearly indistinguishable from the full simulation, as measured by several different metrics.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS2002

Recent Results from the Physics of Colloids in Space

The Physics of Colloids in Space is an experiment which flew in the ISS. Data on several different samples of colloidal particles were obtained. They provided unexpected information about the behavior of the samples in microgravity. The data are currently being analyzed. The most recent findings will be discussed in this talk.

Weitz, David A.↗