Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “future of computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Impact of the Number of Applied Current Meter Sensors on the Accuracy of Flow Rate Measurements across a Range of Hydroelectric Facilities Indicative of the Domestic Hydroelectric Fleet

The following paper represents the results of an investigation into the impact of the number and placement of Current Meter (CM) flow sensors on the accuracy to which they are capable of predicting the overall flow rate. Flow measurement accuracy is of particular importance in multiunit plants because it plays a pivotal role in determining the operational efficiency characteristics of each unit, allowing the operator to select the unit (or combination of units) which most efficiently meet demand. Several case studies have demonstrated that optimization of unit dispatch has the potential to increase plant efficiencies from between 1 to 4.4 percent [2] [3]. Unfortunately current industry standards do not have an established methodology to measure the flow rate through hydropower units with short converging intakes (SCI); the only direction provided is that CM sensors should be used. The most common application of CM is horizontally, along a trolley which is incrementally lowered across a measurement cross section. As such, the measurement resolution is defined horizontally and vertically by the number of CM and the number of measurement increments respectively. There has not been any published research on the role of resolution in either direction on the accuracy of flow measurement. The work below investigates the effectiveness of flow measurement in a SCI by performing a case study in which point velocity measurements were extracted from a physical plant and then used to calculate a series of reference flow distributions. These distributions were then used to perform sensitivity studies on the relation between the number of CM and the accuracy to which the flow rate was predicted. The following research uncovered that a minimum of 795 plants contain SCI, a quantity which represents roughly 12% of total domestic hydropower capacity. In regards to measurement accuracy, it was determined that accuracy ceases to increase considerably due to strict increases in vertical resolution beyond the application of 49 transects. Moreover the research uncovered that the application of 5 CM (when applied at 49 vertical transects) resulted in an average accuracy of 95.6% and the application of additional sensors resulted in a linear increase in accuracy up to 17 CM which had an average accuracy of 98.5%. Beyond 17 CM incremental increases in accuracy due to the addition of CM was found decrease exponentially. Future work that will be performed in this area will investigate the use of computational fluid dynamics to acquire a broader range of flow fields within SCI.

Flow Measurement↗

OES Task 10 WEC Heaving Sphere Performance Modelling Verification

OES Task 10 Modelling, Verification and Validation of Wave Energy Converters (WECs) is a task under the IEA Technology Collaboration Program for Ocean Energy Systems (OES). The long-term goals are to assess the accuracy of, and establish confidence in, the use of numerical WEC models. to determine a range of validity of existing computational modelling tools, to identify uncertainty related to simulation methodologies and finally to define future research. To some extent, this project builds on the experience from a similar effort carried out to verify modelling of wind turbines as part of the IEA Wind Task 30 on wind OC3-OC5.

16 TIDAL AND WAVE POWER↗

Exploring the crossover between high-energy-density plasma and ultracold neutral plasma physics

In this paper, we present ideas that were part of the miniconference on the crossover between High Energy Density Plasmas (HEDP) and Ultracold Neutral Plasmas (UNPs) at the 60th Annual Meeting of the American Physical Society Division of Plasma Physics, November 2018. We give an overview of UNP experiments with an emphasis on measurements of the time-evolving ion density and velocity distributions, the electron-ion thermalization rate, and plasma self-assembly—all just inside the strongly coupled plasma regime. We also present theoretical and computational models that were developed to understand a subset of HEDP experiments. However, because HEDP experiments display similar degrees of strong coupling, many aspects of these models can be vetted using precision studies of UNPs. This comparison is important because some statistical assumptions used for ideal plasmas are of questionable validity in the strongly coupled plasma regime. We summarize two theoretical approaches that extend kinetic theories into the strong-coupling regime and show good agreement for momentum transfer and self-diffusion. As capabilities improve, both computationally and experimentally, UNP measurements may help guide the ongoing development of HEDP-appropriate plasma models. Future opportunities in viscosity, energy relaxation, and magnetized plasmas are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Can the United States Maintain Its Leadership in High-Performance Computing? - A report from the ASCAC Subcommittee on American Competitiveness and Innovation to the ASCR Office

The United States (U.S.) is no longer the unambiguous leader in the vitally important field of high performance computing (HPC). Japan, the European Union (EU), and China have fielded systems that are on par with our fastest supercomputers. The supply chain for everything from semiconductors to scientific software is globally distributed. Yet our economic future and security depend critically on our ability to innovate faster than our competitors, and the speed of innovation depends increasingly on large-scale computational science and engineering and thus HPC. How should the United States respond to this challenge? This report seeks to initiate a new and potentially transformative national discussion on this vital question. The Department of Energy’s (DOE) Advanced Scientific Computing Research (ASCR) program is well-positioned to make informed, targeted decisions about where the United States should cooperate and where it should compete in the global market for scientific exploration and discovery. By setting its sights on problems critical to our nation and the world, by establishing productive new collaborations, and by making strategic investments, ASCR can restore and maintain U.S. scientific leadership in the critical areas described in this report while strengthening our research infrastructure and training a large, diverse cohort of scientists. In doing so, ASCR and its scientists will pave the way for a secure and prosperous future for America. For more than 30 years, the ASCR program has provided the HPC and networking capabilities and expertise needed to support DOE’s mission to advance the national, economic, and energy security of the United States. The program now faces the challenge of developing and deploying the next generation of HPC systems and technologies, as well as supporting the application of HPC and artificial intelligence (AI) technologies to a wide range of scientific and engineering research problems. Through its research and development efforts, the ASCR program must also advance the state of the art in HPC and accelerate the pace of scientific discovery and technological innovation. Fulfilling this promise will require significantly increased investments, as well as innovative policies and programs. This subcommittee is aware that we are making recommendations and calls for action at a time when federal resources are limited. We understand that a wide range of competing priorities must be balanced by the nation’s leaders and that there is a need to leverage resources in new ways and seek efficiencies in facilities and operations. However, we must not let these realities limit our imagination or silence our advocacy. The ASCR program is a key part of the U.S. research infrastructure and an important component of economic growth and U.S. competitiveness. ASCR has a responsibility to pursue its mission, including advanced scientific computing, applications of AI technologies, and the required advanced research facilities, with determination and enthusiasm. To fulfill the scientific enterprise’s responsibility to the nation, the ASCR program must not only develop and publish a clear vision with an associated list of goals, priorities, and recommendations but also demonstrate scientific leadership by consistently securing long-term funding. This will allow the program to build on its achievements to date, to realize its ambitious vision, and to make lasting contributions to the field.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Crystal Engineering of Hydrogen Bonding for Direct Air Capture of CO2: A Quantum Crystallography Perspective

Rising atmospheric CO2 levels demand efficient and sustainable carbon capture solutions. Direct air capture (DAC) via crystallizing hydrogen-bonded frameworks such as carbonate salts has emerged as a promising approach. This review explores the potential of crystal engineering, in tandem with advanced quantum crystallography techniques and computational modeling, to unlock the full potential of DAC materials. We examine the critical role of hydrogen bonding and other noncovalent interactions within a family of bis-guanidines that governs the formation of carbonate salts with high CO2 capture capacity and low regeneration energies for utilization. Quantum crystallography and charge density analysis prove instrumental in elucidating these interactions. A case study of a highly insoluble carbonate salt of a 2,6-pyridine-bis-(iminoguanidine) exemplifies the effectiveness of these approaches. However, challenges remain in the systematic and precise determination of hydrogen atom positions and atomic displacement parameters within DAC materials using quantum crystallography, and limitations persist in the accuracy of current energy estimation models for hydrogen bonding interactions. Future directions lie in exploring diverse functional groups, designing advanced hydrogen-bonded frameworks, and seamlessly integrating experimental and computational modeling with machine learning. This synergistic approach promises to propel the design and optimization of DAC materials, paving the way for a more sustainable future.

36 MATERIALS SCIENCE↗

Learning to Scale the Summit: AI for Science on a Leadership Supercomputer

The Summit system at Oak Ridge National Lab-oratory (ORNL) has been the world's top AI for science su-percomputer for several years, ranked world's fastest computer at its 2018 launch and currently top system in the US and #2 on the TOP5OO list. Summit's purposeful design to handle both conventional modeling and simulation science and emerging AI workloads has made it a leading destination for AI-powered computational science. We report here on AI for science usage on Summit near the midpoint of its lifespan. We review AI usage across the many science projects that have used Summit. We then examine in detail a set of applications scaling AI to full system as well as projects implementing AI-coordinated science discovery workflows on Summit. Finally, we offer some observations regarding the future of advancing scientific knowledge and understanding via AI, especially in the context of leadership-class scientific computing.

Joubert, Wayne↗

Distributed Resources for the Earth System Grid Advanced Management (DREAM)

The DREAM project was funded more than 3 years ago to design and implement a next-generation ESGF (Earth System Grid Federation) architecture which would be suitable for managing and accessing data and services resources on a distributed and scalable environment. In particular, the project intended to focus on the computing and visualization capabilities of the stack, which at the time were rather primitive. At the beginning, the team had the general notion that a better ESGF architecture could be built by modularizing each component, and redefining its interaction with other components by defining and exposing a well defined API. Although this was still the high level principle that guided the work, the DREAM project was able to accomplish its goals by leveraging new practices in IT that started just about 3 or 4 years ago: the advent of containerization technologies (specifically, Docker), the development of frameworks to manage containers at scale (Docker Swarm and Kubernetes), and their application to the commercial Cloud. Thanks to these new technologies, DREAM was able to improve the ESGF architecture (including its computing and visualization services) to a level of deployability and scalability beyond the original expectations. Overall, during its three-year lifespan, DREAM has undertaken innovative research work and prototyping: many of its solutions (the new containerized architecture, the Visus visualization engine, the Solr Cloud based search service) were handed over to the ESGF collaboration, which will make them operational and use them as their future software basis.

42 ENGINEERING↗

ORIGEN Integration into MPACT

This report documents the work performed to meet the objectives of the RTM milestone on ORIGEN Integration into MPACT. The main objective of the milestone was to demonstrate the capability to perform depletion problems with MPACT where the point depletion calculation, which solves the nuclide transmutation equation with ORIGEN. While MPACT already has a depletion capability based on ORIGEN, it is desired to transition to using ORIGEN because ORIGEN has undergone far more validation and software quality assurance than the implementation in MPACT. The integration was completed by compiling and linking the two codes together at build-time. Within the TriBITS build structure used for VERA, the MPACT and SCALE code repositories are already present. An optional dependency was created between MPACT to SCALE. The API available within ORIGEN was modified slightly to be able to be used by MPACT and two new software classes were implemented in MPACT to call the necessary ORIGEN subroutines. To test the ORIGEN integration two benchmark problems were analyzed. The first being the spent fuel isotopics from the Takahama-3 PWR reactor. This involved comparisons to experimentally measured nuclide concentrations for select actinides and fission products, and comparisons to other numerical results. The benchmark defines a 1-D problem limiting most of the effects due to the accuracy of a multi-dimensional transport solver, and thus differences can be assumed to be more likely caused by the point depletion solver methodology and associated nuclear data. The other benchmark analyzed two problems from the reactor physics benchmarks for LWR next generation fuel. The two configurations simulated were a PWR UO 2 pin cell and PWR UO 2 assembly. For all the benchmark problems the results were generally in good agreement with the other numerical results which were computed by several codes, including MPACT with its original depletion implementation. Thus it is concluded that ORIGEN was successfully integrated into MPACT and is capable of providing reasonable results. An additional cursory analysis of the performance of the ORIGEN point depletion compared to native MPACT point depletion solver was also performed. In this analysis it was observed that ORIGEN, on average, needs about 0.28 to 0.30 seconds to perform the point depletion calculation. This is greater than the target performance of 0.1 seconds which means future work to investigate smaller depletion chains will be needed. The MPACT internal depletion solver completes the point depletion calculation in 0.02 seconds, so it may be used for routine analysis until the use of a simplified burnup chain and performance improvements are implemented. Other future work should focus on implementing the post-correction fix-up and quadratic depletion and computation of decay heat and gamma sources.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Preservation of FFTF Data Related to Passive Safety Testing

One of the goals of the Fuel Cycle Research and Development Program (FCRD) is to preserve the knowledge that has been gained in the United States on Liquid Metal Reactors (LMR). A key area deserving special attention for preservation is the data relating to passive safety testing that was conducted in FFTF and EBR-II during the 1980’s. Accidents at Unit 4 of the Chernobyl Station and Unit 2 at Three Mile Island changed the safety paradigm of the nuclear power industry. New emphasis was placed on assured safety based on intrinsic plant characteristics that protect not only the public, but the significant investment in the plant as well. Plants designated to perform in this manner are considered to be passively safe since no active sensor/alarm system or human intervention is required to bring the reactor to a safe shutdown condition. The liquid metal reactor (LMR) has several key characteristics needed for a passively safe reactor: reactor coolant with superior heat transfer capability and very high boiling point, low (atmospheric) system pressures, and reliable negative reactivity feedback. The credibility of the design for a passively safe LMR rests on two issues: the validity of analytic methods used to predict passive safety performance and the availability of relevant test data to calibrate design tools. Safety analysis methods used to analyze LMRs under the old safety paradigm were focused on calculating the source term for the Core Disruptive Accident. Passive safety design requires refined analysis methods for transient events because treatment of the detailed reactivity feedbacks is important in predicting the response of the reactor. Similarly, analytic tools should be calibrated against actual test experience in existing LMR facilities. The principal objectives of the combined FFTF natural circulation and Passive Safety Testing program were: 1) to verify natural circulation as a reliable means to safely remove decay heat, 2) to extend passive safety experience to a large-size LMR and obtain data for validating design analysis computer codes, and 3) to develop and test passive safety enhancements that might be used for future LMRs. These tests were designed to provide data sufficient to allow separation of fuel temperature effects from structural temperature effects. The data developed through this testing program were used to verify the predictive capability of passive safety analysis methods as well as provide a data base for calibrating design tools such as the SASSYS/SAS4A codes. These tests were instrumental in improving understanding of reactivity feedback mechanisms in LMRs and demonstrating passive safety margins available in an LMR. Knowledge preservation at the FFTF is focused on the areas of design, construction, startup, and operation of the reactor. This information may be of potential use for international exchanges with other LMR programs around the world. This information provides the basis for creating benchmarks for validating and testing large scale computer programs. All information preserved to date is now being stored and categorized consistent with the IAEA international standardized taxonomy. The test results information exists in several different formats depending upon the final stage of the test evaluation. Over 100 documents relevant to passive safety testing have been identified and are being recovered, scanned, and catalogued. Attempts to recover plant data tapes are also in progress. Documents related to passive safety testing are now being categorized consistent with internationally agreed upon IAEA standards. Documents are being converted to electronic format compatible with a general search engine being developed by INL. The data from the FFTF passive safety tests provides experimental verification of structural reactivity effects that should be very useful to innovative designers seeking to optimize passive safety in the design of new LMRs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Quantum pattern recognition algorithms for charged particle tracking

High-energy physics is facing a daunting computing challenge with the large datasets expected from the upcoming High-Luminosity Large Hadron Collider in the next decade and even more so at future colliders. A key challenge in the reconstruction of events of simulated data and collision data is the pattern recognition algorithms used to determine the trajectories of charged particles. The field of quantum computing shows promise for transformative capabilities and is going through a cycle of rapid development and hence might provide a solution to this challenge. This article reviews current studies of quantum computers for charged particle pattern recognition in high-energy physics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A Perspective on the Future of High Efficiency Engines

New fuel economy standards and emissions regulations are accelerating the development of new engine technologies, sensors, and on-board computing. These developments will enable unprecedented engine control, which will in turn enable real-world implementations of low temperature combustion, high-speed controls, and other high efficiency engine technologies. With this expanded flexibility in engine design and control, the challenge will now be the exponential increase in the design and calibration space and the need for the development of new simulations, optimization methods, and self-learning control methodologies. This manuscript provides historical and future perspectives on the opportunities and challenges of this unparalleled technology growth on the next generation of high efficiency engines.

Wagner, Robert M↗

Component based development of computer-aided tools for different applications

Computer-aided methods and tools are used at different stages of chemical process development. However new tools are needed to meet the current and future challenges through innovative and more sustainable solutions that the currently available tools may not be able to provide. This work focuses on component-based software architecture for development of tailor-made computer-aided tools for specific application objectives. The architecture is based on “components”, which can be model-objects that are stored in a library; collection of property models; databases; numerical solvers; design-algorithms (work-flows) etc. Furthermore, the main idea of these components is to incorporate a plug & play framework, where for a specific purpose, after the work-flow and associated data-flow are established, a specific computer-aided tool can be configured through a library of software components. Also, through the use of software components that are based on predictive model-based solution techniques, the final software can be reliably used to provide innovative and more sustainable solutions over a wide range of problems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advances and challenges in cryo ptychography at the Advanced Photon Source

Ptychography has emerged as a nondestructive tool to quantitatively study extended samples at a high spatial resolution. In this manuscript, we report on recent developments from our team. We have combined cryo ptychography and fluorescence microscopy to provide simultaneous views of ultrastructure and elemental composition, we have developed multi-GPU parallel computation to speed up ptychographic reconstructions, and we have implemented fly-scan ptychography to allow for faster data acquisition. We conclude with a discussion of future challenges in high-resolution 3D ptychography.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Computation-guided discovery of coating materials to stabilize the interface between lithium garnet solid electrolyte and high-energy cathodes for all-solid-state lithium batteries

All-solid-state batteries with a lithium metal anode, enabled by lithium garnet solid electrolytes such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising next-generation energy-storage technology. The further development of all-solid-state battery requires the integration of high-energy cathodes such as LiNi 1-x-y Mn x Co y O 2 (NMC) with the garnet solid electrolyte with stable and low-resistance interfaces, which requires a coating layer to stabilize the interface during high-temperature sintering and electrochemical cycling. In order to guide the future development of interfacial coatings, we perform high-throughput thermodynamic analyses based on first-principles computation to investigate the stability of LLZO garnet and high-energy NMC cathodes with a wide range of materials chemistries. Here our study reveals the factors governing the materials stability with LLZO garnet and NMC cathodes, and identifies the mechanisms of good coating layers stable with LLZO and NMC. In addition to classifying known coating layers, our study provides detailed guiding charts and multiple new materials systems as promising coatings for stabilizing LLZO—NMC interfaces to enable high-energy-density garnet-based all-solid-state batteries. Our demonstrated computation scheme and high-throughput analyses are generally applicable to investigate and screen coating materials for stabilizing interfaces in energy-related applications.

25 ENERGY STORAGE↗

Identifying Entangled Physics Relationships Through Sparse Matrix Decomposition to Inform Plasma Fusion Design

We report a sustainable burn platform through inertial confinement fusion (ICF) has been an ongoing challenge for over 50 years. Mitigating engineering limitations and improving the current design involves an understanding of the complex coupling of physical processes. While sophisticated simulation codes are used to model ICF implosions, these tools contain necessary numerical approximation but miss physical processes that limit predictive capability. Identification of relationships between controllable design inputs to ICF experiments and measurable outcomes (e.g., neutron yield, neutron velocity, areal density) from performed experiments can help guide the future design of experiments and development of simulation codes, to potentially improve the accuracy of the computational models used to simulate ICF experiments. We use sparse matrix decomposition methods to identify clusters of a few related design variables. Sparse principal component analysis (SPCA) identifies groupings that are related to the physical origin of the variables (laser, hohlraum, and capsule). A variable importance analysis finds that in addition to variables highly correlated with neutron yield, such as picket power and laser energy, variables that represent a dramatic change of the ICF design, such as number of pulse steps, are also very important. The obtained sparse components are then used to train a random forest (RF) regression surrogate for predicting total yield. The RF performance on the training and testing data compares with the performance of the RF trained using all the design variables considered. This work is intended to inform design changes in future ICF experiments by augmenting the expert intuition and simulation results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shielding integral benchmark archive and database (SINBAD)

The shielding integral benchmark archive and database (SINBAD) collection of experiments descriptions was initiated in the early 1990s. SINBAD is an international collaboration between the Organization for Economic Cooperation and Development's Nuclear Energy Agency Data Bank (OECD/NEADB) and the Radiation Safety Information Computational Center (RSICC) at Oak Ridge National Laboratory (ORNL). SINBAD was designed to compile experiments and corresponding computational models with the goal of preserving institutional knowledge and expertise that need to be handed down to future scientists. SINBAD can serve as a learning tool for university students and scientists who need to design experiments or gain expertise in modeling and simulation. The SINBAD database is currently divided into three categories - fission, fusion, and accelerator experiments. Many experiments are described and analyzed using deterministic or stochastic (Monte Carlo) radiation transport software. The nuclear cross sections also play an important role as they are necessary in performing computational analysis. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Toward coherent quantum computation of scattering amplitudes with a measurement-based photonic quantum processor

In recent years, applications of quantum simulation have been developed to study the properties of strongly interacting theories. This has been driven by two factors: on the one hand, needs from theorists to have access to physical observables that are prohibitively difficult to study using classical computing; on the other hand, quantum hardware becoming increasingly reliable and scalable to larger systems. In this work, we discuss the feasibility of using quantum optical simulation for studying scattering observables that are presently inaccessible via lattice QCD and are at the core of the experimental program at Jefferson Laboratory, the future Electron-Ion Collider, and other accelerator facilities. We show that recent progress in measurement-based photonic quantum computing can be leveraged to provide deterministic generation of required exotic gates and implementation in a single photonic quantum processor. Published by the American Physical Society 2024

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗