Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Steady, subsonic, lifting surface theory for wings with swept, partial span, trailing edge control surfaces

A method for computing the lifting pressure distribution on a wing with partial span, swept control surfaces is presented. This method is valid within the framework of linearized, steady, potential flow theory and consists of using conventional lifting surface theory in conjuction with a flap pressure mode. The cause of a numerical instability that can occur during the quadrature of the flap pressure mode is discussed, and an efficient technique to eliminate the instability is derived. This technique is valid for both the flap pressure mode and regular pressure modes and could be used to improve existing lifting surface methods. Examples of the use of the flap pressure mode and comparisons among this method, other theoretical methods, and experiments are given. Discrepancies with experiment are indicated and candidate causes are presented. It is concluded that the method can lead to an efficient and accurate solution of the mathematical problem when a partial span, trailing edge flap is involved.

Medan, R. T.↗
NASA NTRS1972

Acoustic characteristics of large-scale STOL model at forward speed

Wind-tunnel investigations of the acoustic characteristics of the externally blown jet flap (EBF) and augmentor wing STOL concepts are dicussed. The large-scale EBF model was equipped with a triple-slotted blown by four JT15D turbofan engines with circular, coannular exhaust nozzles. The large-scale augmentor wing model was equipped with an unlined augmentor blown by a slot primary nozzle. The effects of airspeed and angle of attack on the acoustics of the EBF were small. At a forward speed of 60 knots, the impingement noise of the landing flap was approximately 2 db lower than in the static tests. Angle of attack increased the impingement noise approximately 0.1 decibels per degree. Flap deflection had a greater effect on the acoustics of the augmentor wing than did airspeed. For a nozzle pressure ratio of 1.9, the peak perceived noise level of the landing flap was 3 to 5 PNdb higher than that of the takeoff flap. The total sound power was also significantly higher for landing indicating that turning in the augmentor generated acoustic energy. Airspeed produced a small aft shift in acoustic directivity with no significant change in the peak perceived noise levels or sound power levels.

Falarski, M. D.↗
NASA NTRS1973

A Study of Trailing Edge Blowing as a Means of Reducing Noise Generated by the Interaction of Flow with a Surface

A system for reducing the noise generated when a jet impinges against a flap is described. The eddies formed by the alternate zones of positive and negative pressure on the flap surface are identified as the sound source. In the proposed concept, a stream of low velocity secondary air is ejected from a slot near the trailing edge of the flap as a buffer between the flap and the primary air jet to reduce the intensity of the fluctuating surface pressure field near the flap edge and thus reduce the intensity of the aerodynamic noise.

Scharton, T. D.↗
NASA NTRS1973

Some conclusions regarding the aeroelastic stability of hingeless helicopter blades in hover and in forward flight

In this paper results and conclusions obtained from the study of the aeroelastic instability of hingeless helicopter blades are presented. First, the large amplitude coupled flap-lag equations of motion of a hingeless elastic helicopter blade are solved using an asymptotic expansion procedure in multiple time scales. Both hover and forward flight cases are considered. Stability boundaries and amplitudes of nonlinear response are obtained. From these, the importance of the nonlinear coupling and the effect of the periodic coefficients is determined. Next, using a system of linearized coupled flap-lag-pitch equations in hover, various divergence mechanisms for hingeless blades are shown. Finally, the flutter boundaries for coupled flap-lag-pitch are obtained. The effect of the torsional degree of freedom on the flap-lag type of instability is investigated. Similarly the effect of lag on the flap-pitch type of instability is considered. In addition, the effect of various blade parameters on the stability boundaries is shown.

Friedmann, P.↗
NASA NTRS1975

Low speed wind tunnel investigation of a four-engine upper surface blown model having swept wing and rectangular and D-shaped exhaust nozzles

A low speed investigation was conducted in the Langley V/STOL tunnel to determine the power-on static-turning and powered-lift aerodynamic performance of a four engine upper surface blown transport configuration. Initial tests with a D-shaped exhaust nozzle showed relatively poor flow-turning capability, and the D-nozzles were replaced by rectangular nozzles with a width-height ratio of 6.0. The high lift system consisted of a leading edge slat and two different trailing-edge-flap configurations. A double slotted flap with the gaps sealed was investigated and a simple radius flap was also tested. A maximum lift coefficient of approximately 9.3 was obtained for the model with the rectangular exhaust nozzles with both the double slotted flap deflected 50 deg and the radius flap deflected 90 deg.

Sleeman, W. C., Jr.↗
NASA NTRS1976

Noise measurements for a twin-engine commercial jet aircraft during 3 deg approaches and level flyovers

Noise measurements have been made with a twin-engine commercial jet aircraft making 3 deg approaches and level flyovers. The flight-test data showed that, in the standard 3 deg approach configuration with 40 deg flaps, effective perceived noise level (EPNL) had a value of 109.5 effective perceived noise decibels (EPNdB). This result was in agreement with unpublished data obtained with the same type of aircraft during noise certification tests; the 3 deg approaches made with 30 deg flaps and slightly reduced thrust reduced the EPNL value by 1 EPNdB. Extended center-line noise determined during the 3 deg approaches with 40 deg flaps showed that the maximum reference A-weighted sound pressure level (LA,max)ref varied from 100.0 A-weighted decibels 2.01 km (108 n. mi.) from the threshold to 87.4 db(A) at 6.12 km (3.30 n. mi.) from the threshold. These test values were about 3 db(A) higher than estimates used for comparison. The test data along the extended center line during approaches with 30 deg flaps were 1 db(A) lower than those for approaches with 40 deg flaps. Flight-test data correlating (LA,max)ref with thrust at altitudes of 122 m (400 ft) and 610 m (2000 ft) were in agreement with reference data used for comparison.

Hastings, E. C., Jr.↗
NASA NTRS1975

An analytical study of a multicycle controllable twist rotor

A rotor employing a servo-flap to effect blade torsional deflections (the Kaman Controllable Twist Rotor) has been used in a theoretical study to assess the potential of multicyclic flap control, (i.e., 1P, 2P, 3P, and 4P flap deflections). The results show that virtual elimination of pylon vibratory loads may be achieved with concurrent blade bending moments reduced by 50%. The amplitude requirements of the higher harmonic deflections are of the order of 3 or 4 deg. The study is in two parts; the calculation of rotor loads for specific combinations of multicyclic flap deflections by a typical rotor computer analysis, and an analysis of those results to determine optimum combinations of the multicyclic flap control. The paper discusses the analysis and indicates the potentials of a multicyclic controllable twist rotor.

Mccloud, J. L., III↗
NASA NTRS1977

Effects of geometry and jet velocity on noise associated with an upper-surface-blowing model

The noise characteristics associated with various upper surface blowing configurations were investigated using a small model consisting of a plate and flap assembly (simulated wing with flap) attached to a rectangular nozzle. Nozzle aspect ratio, flow-run length, and flap-deflection angle were the experimental parameters studied. Three nozzle-exit velocities were used. The normalized noise spectra obtained for different nozzle aspect ratios proved to be similar in terms of Strouhal number based on jet velocity and flow-run length. Consequently, the need for knowing local flow velocity and length scales (for example, at the flap trailing edge) as required in some of the existing noise prediction schemes is eliminated. Data are compared with results computed from three different noise prediction schemes, and the validity of each scheme is assessed. A simple method is proposed to evaluate the frequency dependence of acoustic shielding obtained with the simulated wing flap.

Clark, L. R.↗
NASA NTRS1977

Static, noise, and transition tests of a combined-surface-blowing V/STOL lift/propulsion system

Efficient thrust vectoring and high levels of circulatory lift were obtained in tests of a half model V/STOL airplane by using a type of externally blown jet flap in which the jet exhaust from wing-mounted cruise fans is directed over both upper and lower surfaces of a flapped wing. Approximately 90% thrust recovery with 87 deg of thrust vectoring was achieved under static conditions using 89 deg of trailing edge flap deflection. The approximately 10% loss appears to be associated primarily with pressure losses due to the flap brackets or slot entries. The jet induced lift was shown to be 55% of the theoretical value for a fullspan jet-flapped wing, even though only 27.5% of the wingspan was immersed in the jet. Steady rate of descent capability in excess of 1,000 feet per minute is predicted. The possibility of significant aerodynamic-noise cancelling when blowing over both surfaces at high velocities is indicated.

Schoen, A. H.↗
NASA NTRS1978

Dynamic wind-tunnel tests of an aeromechanical gust-alleviation system using several different combinations of control surfaces

Some experimental results are presented from wind tunnel studies of a dynamic model equipped with an aeromechanical gust alleviation system for reducing the normal acceleration response of light airplanes. The gust alleviation system consists of two auxiliary aerodynamic surfaces that deflect the wing flaps through mechanical linkages when a gust is encountered to maintain nearly constant airplane lift. The gust alleviation system was implemented on a 1/6-scale, rod mounted, free flying model that is geometrically and dynamically representative of small, four place, high wing, single engine, light airplanes. The effects of flaps with different spans, two size of auxiliary aerodynamic surfaces, plain and double hinged flaps, and a flap elevator interconnection were studied. The model test results are presented in terms of predicted root mean square response of the full scale airplane to atmospheric turbulence. The results show that the gust alleviation system reduces the root mean square normal acceleration response by 30 percent in comparison with the response in the flaps locked condition. Small reductions in pitch-rate response were also obtained. It is believed that substantially larger reductions in normal acceleration can be achieved by reducing the rather high levels of mechanical friction which were extant in the alleviation system of the present model.

Stewart, E. C.↗
NASA NTRS1976

Some measurements of an EBF powered-lift wake

Results from a wind tunnel investigation in which velocity vector measurements were obtained in the near wake of an externally blown flap powered lift configuration were analyzed. These measurements were used to develop spanwise distributions for the momentum strength and location of the engine exhaust stream tube with the results used as input parameters to one jet flap analytical method. It is shown that a comparison of the momentum coefficients obtained from forward speed wake surveys with the predicted values from static force data results in a good correlation, which verifies the use of the flap thrust recovery factor as a means of predicting the momentum strength at the flap trailing edge. Also, when wake survey distributions of momentum strength and direction are used as input parameters to one analytical jet flap method, the results show reasonable agreement between the experimental data and analytical results.

Johnson, W. G., Jr.↗
NASA NTRS1978

Measurements of noise produced by flow past lifting surfaces

Wind tunnel studies have been conducted to determine the specific locations of aerodynamic noise production within the flow field about various lifting-surface configurations. The models tested included low aspect ratio shapes intended to represent aircraft flaps, a finite aspect ratio NACA 0012 wing, and a multi-element wing section consisting of a main section, a leading edge flap, and dual trailing edge flaps. Turbulence was induced on the models by surface roughness. Lift and drag were measured for the flap models. Hot-wire anemometry was used for study of the flap-model vortex roll-up. Apparent noise source distributions were measured by use of a directional microphone system, located outside the tunnel, which was scanned about the flow region to be analyzed under computer control. These distributions exhibited a diversity of pattern, suggesting that several flow processes are important to lifting-surface noise production. Speculation concerning these processes is offered.

Kendall, J. M.↗
NASA NTRS1979

The size and performance effects of high lift system technology on a modern twin engine jet transport

The energy and economic benefits of low-speed aerodynamic system technology applied to a modern 200-passenger, 2000-nmi range, twin engine jet transport are reviewed. Results of a new method to design flap systems at flight Reynolds number are summarized. The study contains the airplane high lift configuration drag characteristics and design selection charts showing the effect of flap technology on the airplane size and performance. The study areas include: wing and flap geometry, climb and descent speed schedules with partial flap deflection, flap system technology, and augmented stability. The results compare the improvements in payload from a hot, high elevation airport.

Sullivan, R. L.↗
NASA NTRS1981

Wind-tunnel studies of advanced cargo aircraft concepts

Accomplishments in vortex flap research are summarized. A singular feature of the vortex flap is that, throughout the range of angle of attack range, the flow type remains qualitatively unchanged. Accordingly, no large or sudden change in the aerodynamic characteristics, as happens when forcibly maintained attached flow suddenly reverts to separation, will occur with the vortex flap. Typical wind tunnel test data are presented which show the drag reduction potential of the vortex flap concept applied to a supersonic cruise airplane configuration. The new technology offers a means of aerodynamically augmenting roll-control effectiveness on slender wings at higher angles of attack by manipulating the vortex flow generated from leading edge separation. The proposed manipulator takes the form of a flap hinged at or close to the leading edge, normally retracted flush with the wing upper surface to conform to the airfoil shape.

Rao, D. M.↗
NASA NTRS1982

An experimental and theoretical investigation of thick wings at various sweep angles in and out of ground effect

The effects of sweep and aspect ratio on the longitudinal aerodynamics of a wing in and out of ground effect are analyzed. Experimental data were obtained in the Langley 4 by 7 Meter Tunnel for a wing with various sweep angles, aspect ratios, and flap deflections both in and out of ground effect. Theoretical predictions of the out of ground effect lift coefficients and flap effectiveness and the in ground effect lift coefficients are compared with the experimental results. As expected, the lift curve slope and flap effectiveness are reduced when the aspect ratio is reduced or the sweep angle is increased both in and out of ground effect. In ground effect, the lift and flap effectiveness are increased above a wing height to span ratio of 0.15. However, with flap deflections less than or equal to 10 deg and an angle of attack near 0 deg lift is markedly decreased at very low heights above the ground plane. This trend is not predicted by planar theoretical models but is predicted by a surface panel method where thickness effects are included.

Paulson, J. W., Jr.↗
NASA NTRS1983

Investigation of jet-installation noise sources under static conditions

The acoustical effects of operating a 6-cm exit-diameter nozzle in the presence of a wing-flap model under static conditions are examined experimentally. The geometric parameters of the wing-flap model are chosen to represent a realistic jet-engine installation on a wide-body midrange transport airplane. The effects of varying the installation parameters and the noise sources associated with the engine-installation effects are discussed. The major noise sources are the flow interaction of the jet and wing undersurface, the flow interaction of the jet with the side edges of the flap cutout and flap trailing edge, and the reflection of the jet noise off the undersurface of the wing and flap.

Shearin, J. G.↗
NASA NTRS1982

The investigation of a variable camber blade lift control for helicopter rotor systems

A new rotor configuration called the variable camber rotor was investigated numerically for its potential to reduce helicopter control loads and improve hover performance. This rotor differs from a conventional rotor in that it incorporates a deflectable 50% chord trailing edge flap to control rotor lift, and a non-feathering (fixed) forward portion. Lift control is achieved by linking the blade flap to a conventional swashplate mechanism; therefore, it is pilot action to the flap deflection that controls rotor lift and tip path plane tilt. This report presents the aerodynamic characteristics of the flapped and unflapped airfoils, evaluations of aerodynamics techniques to minimize flap hinge moment, comparative hover rotor performance and the physical concepts of the blade motion and rotor control. All the results presented herein are based on numerical analyses. The assessment of payoff for the total configuration in comparison with a conventional blade, having the same physical characteristics as an H-34 helicopter rotor blade was examined for hover only.

Awani, A. O.↗
NASA NTRS1984

Static internal performance of single-expansion-ramp nozzles with various combinations of internal geometric parameters

The effects of five geometric design parameters on the internal performance of single-expansion-ramp nozzles were investigated at nozzle pressure ratios up to 10 in the static-test facility of the Langley 16-Foot Transonic Tunnel. The geometric variables on the expansion-ramp surface of the upper flap consisted of ramp chordal angle, ramp length, and initial ramp angle. On the lower flap, the geometric variables consisted of flap angle and flap length. Both internal performance and static-pressure distributions on the centerlines of the upper and lower flaps were obtained for all 43 nozzle configurations tested.

Re, R. J.↗