Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electronics analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Microwave assisted combustion synthesis of nanocrystalline CoFe{sub 2}O{sub 4} for LPG sensing

A microwave-assisted citrate precursor method has been utilized for synthesis of nanocrystalline powders of CoFe{sub 2}O{sub 4}. The process takes only a few minutes to obtain as-synthesized CoFe{sub 2}O{sub 4}. Structural properties of the synthesized material were investigated by X-ray diffraction; scanning electron microscopy, Thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy. The gas sensing properties of thick film of CoFe{sub 2}O{sub 4} prepared by screen printing towards Liquid Petroleum Gas (LPG) revealed that CoFe{sub 2}O{sub 4} thick films are sensitive and shows maximum sensitivity at 350°C for 2500 ppm of LPG.

36 MATERIALS SCIENCE↗

Organic pollutant photodecomposition by Ag/KNbO 3 nanocomposites: A combined experimental and theoretical study

In this study, Ag nanoparticles supported on well-defined perovskite orthorhombic KNbO 3 nanowires are synthesized via facile photoreduction and systematically characterized by XRD, Raman, DRUV–vis, XPS, PL, TEM, HRTEM, and HAADF-STEM. The photoreactivity of Ag/KNbO 3 nanocomposites as a function of Ag contents (0.4–2.8 wt %) is assessed toward aqueous rhodamine B degradation under UV- and visible-light, respectively. It is found that the UV-induced photoreactivity initially increases and then decreases with increasing Ag contents. At an optimal Ag content (ca. 1.7 wt %), the greatest photoreactivity is achieved under UV light, with the photocatalytic reaction rate of 1.7 wt % Ag/KNbO 3 exceeding that of pristine KNbO 3 by a factor of ca. 13. In contrast, visible light-induced photoreactivity monotonically increases with increasing Ag contents in the range of 0.4–2.8 wt %. On the basis of the detected active species and intermediate products in the photocatalytic processes, conjugated structure cleavage and N-deethylation are revealed to be the respective predominant pathway under UV and visible-light illumination. To gain an insight into the observed photoreactivity, the electronic properties of Ag/KNbO 3 have been investigated using spin-polarized DFT calculations. Herein, Ag extended adlayers (1–4 ML) on the slab models of KNbO 3 (101) are employed to mimic large supported Ag nanoparticles. A Bader analysis of the electron density shows a small net charge transfer (ca. 0.1 e) from KNbO 3 to Ag. The electron localization function of Ag/KNbO 3 (101) illustrates that Ag adlayers with thickness larger than 2 ML are essentially metallic, and weak polarization occurs at the interface. In addition, the metallic Ag adlayers generate a continuum of Ag bandgap states, which play a key role in determining different Ag content-dependent behavior between UV and visible-light illumination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Magnetic resonance force microscopy with matching frequencies of cantilever and spin

We have studied theoretically magnetic resonance force microscopy with a high-frequency nanomechanical cantilever when the cantilever frequency matches the resonant frequency of a single electron spin. Our analysis shows that in this situation, there is a small probability that the cantilever will oscillate with a large frequency shift. In conclusion, this can open new experimental opportunities for increasing the sensitivity in the detection of a single electron spin or even a single nuclear spin by using a high-frequency cantilever.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Near real-time streaming analysis of big fusion data

Experiments on fusion plasmas produce high-dimensional data time series with ever-increasing magnitude and velocity, but turn-around times for analysis of this data have not kept up. For example, many data analysis tasks are often performed in a manual, ad-hoc manner some time after an experiment. In this article, we introduce the Delta framework that facilitates near real-time streaming analysis of big and fast fusion data. By streaming measurement data from fusion experiments to a high-performance compute center, Delta allows computationally expensive data analysis tasks to be performed in between plasma pulses. This article describes the modular and expandable software architecture of Delta and presents performance benchmarks of individual components as well as of an example workflow. Focusing on a streaming analysis workflow where electron cyclotron emission imaging (ECEi) data is measured at KSTAR on the National Energy Research Scientific Computing Center's (NERSC's) supercomputer we routinely observe data transfer rates of about 4 Gigabit per second. In NERSC, a demanding turbulence analysis workflow effectively utilizes multiple nodes and graphical processing units and executes them in under 5 min. We further discuss how Delta uses modern database systems and container orchestration services to provide web-based real-time data visualization. For the case of ECEi data we demonstrate how data visualizations can be augmented with outputs from machine learning models. Here, by providing session leaders and physics operators, results of higher-order data analysis using live visualizations may make more informed decisions on how to configure the machine for the next shot.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Propagation of gamma rays and production of free electrons in air

This paper is devoted to the analysis of production of free electrons in air by gamma-rays leaking from radioactive materials. A model based on the Klein-Nishina scattering theory is used to calculate scattering cross sections and approximate the electron production rate. The model includes the effects of primary gamma-quanta radiated by the source as well as that scattered in air. Comparison of the model with the mcnpx kinetic code (http://mcnpx.lanl.gov/) in a sample problem shows excellent agreement. The motivation for this research comes from the recently proposed concept of remote detection of concealed radioactive materials [V. L. Granatstein and G. S. Nusinovich, J. Appl. Phys. 108, 063304 (2010)]. The concept is based on the breakdown in air at the focal point of a high-power beam of electromagnetic waves produced by a THz gyrotron with a 10-20 {mu}s pulse. The presence of a radioactive material can greatly exceed the production rate of free electrons over the natural background rate. Additional electrons act as seeds to initiate the breakdown and create sufficiently dense plasma at the focal region. The dense plasma can then be remotely detected as an unambiguous effect of the concealed radioactive material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward Greener Polymeric Blends: Study of PBAT/Thermoplastic Whey Protein Isolate/Beeswax Blends

This work evaluated the effects of partial substitution of PBAT by thermoplastic whey protein isolate (WPIT) with addition of beeswax through blends processing and their morphological, mechanical, structural, thermal and rheological properties. Whey protein isolate (WPI) was denatured at 90 °C, using glycerol as plasticizer, to be transformed in a thermoplastic material and subsequently blended with PBAT using a torque rheometer at 130 °C. Addition of 10 and 30% of WPIT in the PBAT matrix was investigated with and without beeswax. Blends were pressed as films with ~ 320 µm of thickness. Scanning electron microscopy (SEM) analysis of PBAT/WPIT blends films revealed the presence of domains. These domains are compounded of whey protein, while at the continuous phase a moderate degree of mixture between PBAT and WPIT was observed by Raman analyses. WPIT did not alter the degree of crystallinity and the glass-transition temperature (T{sub g}) of the PBAT in the blends. Thermogravimetric curves of the blends showed decomposition stages related to WPIT and PBAT phases. Thermal stability of blends decreased in comparison to WPIT, which was associated to the cleavage of disulfide bonds of WPIT during processing and causes other kind of interaction between components. Besides, blends containing WPIT remained non-rigid polymers with Young’s modulus below 70 MPa. The tensile strength and elongation at break decreased due the presence of WPIT. Beeswax did not influence the thermal and mechanical properties explored in this study.

36 MATERIALS SCIENCE↗

Electron and photon structure functions at two loops

We present a fully analytic computation of the complete electron and photon structure functions, or QED lepton parton distribution functions (PDFs) up to two-loop order. Our computation is performed using modern techniques of reduction to Master Integrals and solving them with the differential equation method. We obtain explicit expressions for the electron-in-electron, positron-in-electron, photon-in-electron, electron-in-photon, and photon-in-photon distributions at next-to-next-to-leading order (NNLO). Cross-checks against one-loop results, existing two-loop calculations, and a recent soft-collinear effective theory (SCET) analysis of the electron structure functions are presented.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

CO 2 electro-reduction on Cu 3 P: Role of Cu(I) oxidation state and surface facet structure in C 1 -formate production and H 2 selectivity

We report the catalytic activity and mechanism of copper(I) phosphide, Cu 3 P, with predominant [00Ι] facet exposure for the electrochemical reduction of CO 2 (CO 2 RR) to formic acid. Crystalline nanosheets of this compound that show a preferential [00Ι] facet orientation exhibit undiminished CO 2 RR activity after 16 hours with full retention of crystal structure and surface chemical speciation and no detectable corrosion. In contrast to the range of products formed on Cu metal, CuO, and Cu 2 O, the CO 2 RR on Cu 3 P [00Ι] produces mainly hydrogen and formate as the sole carbon product in KHCO 3 electrolyte. Analysis of the Cu 3 P [00Ι] facet by HAADF-STEM was used to determine the surface lattice structure, while both XPS and Auger spectroscopies were used to determine the surface chemical speciation from the kinetic energies of ionized electrons. The presented analysis identifies isolated trigonal CuP 3 sites on the Cu 3 P[00Ι]-Cu 3 P 3 terminated surface and the Cu(I) oxidation state as precursor to the active catalyst. The CO 2 RR selectivity to formate and the higher turnover rate for H 2 production on the [00Ι] facet allows a structure-activity analysis and chemical mechanism to be proposed. Formation of a surface hydride at isolated *H-CuP 3 sites is proposed as the catalytic site in forming both H 2 and formate, while the long Cu—Cu separation retards forming C-C coupling products. In conclusion, these results disprove previously published claims of Cu(I) oxidation state as a sufficient criterion to promote CO 2 RR to C 2+ products, show that stronger bonded hydrides, *H-CuP 3 on Cu 3 P, favor production of the C1 product formate over all other carbon products, and predict that stronger formate binding (bidentate) is needed for CO 2 RR currents to compete with H 2 production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ high-temperature X-ray diffraction study of Sc-doped titanium oxide nanocrystallites

Titanium dioxide is an inexpensive wide-gap highly ionic semiconductor with striking photocatalytic capabilities in several heterogeneous photoredox reactions. A small crystal size is desirable to maximize the surface area, since photocatalytic reactions occur at the surface of a photocatalyst. Presented in this work are the synthesis and microstructural characterization of 4 at.% Sc-doped TiO 2 (4SDT) prepared by water-based co-precipitation. The crystal structure of 4SDT was examined via in situ high-temperature powder X-ray diffraction experiments from 25 to 1200°C. Rietveld analysis revealed single-phase anatase up to 875°C, while at 900°C the anatase-to-rutile phase transformation occurred and at higher temperatures additional reflections of Sc-rich phases (Sc 2 TiO 5 from 975°C and Ti 3 Sc 4 O 12 or Sc 2 O 3 at 1200°C) were observed. Debye function analysis (DFA) was applied to model the total scattering pattern directly in reciprocal space, allowing the reconstruction of Ti vacancies. Both Rietveld and DFA methods were applied to estimate the nanocrystallite size and shape with consistent growth in crystallite size with temperature: an ellipsoid shape with equatorial ~4.7 nm / axial (001) ~6.9 nm at 25°C to equatorial ~27.9 nm / axial (001) ~39.6 nm at 900°C refined by Rietveld analysis, versus a cylinder shape with D a , b = 4.3 nm and size dispersion σ ab = 1.5 nm, L c = 4.9 nm and σ c = 2.3 nm at 25°C to D a , b = 21.4 nm, σ ab = 8.3 nm, L c = 23.9 and σ c = 10.9 nm at 900°C estimated by DFA. The microstructural changes obtained by Rietveld and DFA methods were supported by high-resolution transmission electron microscopy image analysis, as well as by the less direct nitrogen sorption techniques that provide information on the size of non-agglomerated and dense particles. The Ti site-occupancy factor showed a linear increase from 0.6–0.8 at 25°C to unity at 900°C for anatase, and from ~0.7 at 900°C to unity at 1200°C for rutile, via Rietveld analysis and DFA.

36 MATERIALS SCIENCE↗

Electronic Structure and Dynamics of Higher-Lying Excited States in Light Harvesting Complex 1 from Rhodobacter sphaeroides

Light harvesting in photosynthetic organisms involves efficient transfer of energy from peripheral antenna complexes to core antenna complexes, and ultimately to the reaction center where charge separation drives downstream photosynthetic processes. Antenna complexes contain many strongly coupled chromophores, which complicates analysis of their electronic structure. Two-dimensional electronic spectroscopy (2DES) provides information on energetic coupling and ultrafast energy transfer dynamics, making the technique well suited for the study of photosynthetic antennae. Here in this paper, we present 2DES results on excited state properties and dynamics of a core antenna complex, light harvesting complex 1 (LH1), embedded in the photosynthetic membrane of Rhodobacter sphaeroides . The experiment reveals weakly allowed higher-lying excited states in LH1 at 770 nm, which transfer energy to the strongly allowed states at 875 nm with a lifetime of 40 fs. The presence of higher-lying excited states is in agreement with effective Hamiltonians constructed using parameters from crystal structures and atomic force microscopy (AFM) studies. The energy transfer dynamics between the higher- and lower-lying excited states agree with Redfield theory calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microscopic analysis of copper current collectors and mechanisms of fragmentation under compressive forces

Extensive fragmentation of copper current collectors was observed after spherical indentation on prismatic and large-format pouch Li-ion cells by 3D X-ray computed tomography (XCT). Microscopic analysis including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM) and x-ray photoelectron microscopy (XPS) was carried out on copper current collectors from used commercial cells and pristine anodes. The copper-graphite cross-section images showed rough interface areas affected by reactions and diffusion in the used cell. Electron probe micro-analyzer (EPMA) element mapping showed the interface area was rich in oxygen and phosphorus. A detectable amount of phosphorus was also uniformly distributed inside the current collector. The same oxygen and phosphorus distributions were confirmed by STEM/EDS analysis. XPS depth profiles on multiple elements revealed the interface area of the aged anode was rich in Li, F, P, O and C and diffused at least 50 nm into the copper. In comparison, the pristine anode showed a very smooth C/Cu interface. No other elements were detected. For commercial cells, the reactions in the interface area and diffusion of multiple elements into the lattice and grain boundaries were responsible for the embrittlement of the copper current collectors. Finally, permanent cell capacity loss was observed in electrochemical performance of the indented cells.

36 MATERIALS SCIENCE↗

Enhancement in dielectric behavior of (Ni, Zn)Fe{sub 2}O{sub 4} ferrite

In present work, NiFe{sub 2}O{sub 4}(NFO), ZnFe{sub 2}O{sub 4} (ZFO) and Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} (NZFO) are synthesized by microwave assisted co-precipitation route. Their structural properties are confirmed by X-ray diffraction and data is fitted through Reitveld refinement using Full-Prof software suite. After refinement, the systematic crystal structures of NFO, ZFO and NZFO compounds are generated using output .cif file by VESTA (Visualization for Electronic and Structural Analysis) program. Structural parameters obtained after refinement and unit cell construction, are systematically tabulated. Room temperature frequency dependence dielectric properties are studied. We found enhanced values of dielectric constant for NZFO than individual NFO and ZFO phases. For NZFO sample, greater electron exchange between Fe{sup 2+} and Fe{sup 3+} which enhances polarization and dielectric constant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis and simulation for a model of electron impact excitation/deexcitation and ionization/recombination

This paper describes a kinetic model and a corresponding Monte Carlo simulation method for excitation/deexcitation and ionization/recombination by electron impact in a plasma free of external fields. The atoms and ions in the plasma are represented by continuum densities and the electrons by a particle distribution. A Boltzmann-type equation is formulated and a corresponding H-theorem is formally derived. An efficient Monte Carlo method is developed for an idealized analytic model of the excitation and ionization collision cross sections. To accelerate the simulation, the reduced rejection method and binary search method are used to overcome the singular rate in the recombination process. Numerical results are presented to demonstrate the efficiency of the method on spatially homogeneous problems. The evolution of the electron distribution function and atomic states is studied, revealing the possibility under certain circumstances of system relaxation towards stationary states that are not the equilibrium states, a potential non-ergodic behavior.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Analysis of correlations between intrinsic ductility and electronic density of states in refractory alloys

High entropy alloys (HEAs) correspond to a new and emerging class of materials that allows us to explore a large composition space to tune mechanical strength and thermal stability. Therefore, to design better alloys, it is important to scan the high-dimensional space of chemistry, composition and temperature. Here, to facilitate this search, we present a method to screen intrinsically ductile body centered cubic (BCC) refractory alloys from electronic structure calculations by using the density of states (DOS) at the Fermi level, g(μ F ). This correlation between intrinsic ductility and g(μ F ) is tested by analyzing group V (V, Nb, Ta) and VI (Mo, W) refractory metals, binary alloys, such as W-Nb, W-V, Mo-Nb and Mo-V, and refractory alloys for which experimental stress-strain measurements are available. In addition, we perform a high-throughput exploration of the entire composition space of a recently proposed alloy system, CrMoNbV, and identify compositions that exhibit high intrinsic ductility.

36 MATERIALS SCIENCE↗

Fundamental electronic structure and multiatomic bonding in 13 biocompatible high-entropy alloys

High-entropy alloys (HEAs) have attracted great attention due to their many unique properties and potential applications. The nature of interatomic interactions in this unique class of complex multicomponent alloys is not fully developed or understood. We report a theoretical modeling technique to enable in-depth analysis of their electronic structures and interatomic bonding, and predict HEA properties based on the use of the quantum mechanical metrics, the total bond order density (TBOD) and the partial bond order density (PBOD). Application to 13 biocompatible multicomponent HEAs yields many new and insightful results, including the inadequacy of using the valence electron count, quantification of large lattice distortion, validation of mechanical properties with experiment data, modeling porosity to reduce Young’s modulus. This work outlines a road map for the rational design of HEAs for biomedical applications.

36 MATERIALS SCIENCE↗

Instabilities of relativistic counterstreaming proton beams in the presence of a thermal electron background

A linear stability analysis is performed for two counterstreaming proton beams in the presence of a thermal electron background. Growth rates and polarization properties of unstable modes are calculated for various density ratios of the proton beams. It is found that in most cases, two unstable modes grow simultaneously: an electromagnetic filamentary mode that propagates perpendicular to the beam and an electrostatic mode that propagates parallel to the beam. The growth rates of the two modes are comparable, so that one expects that the instability would result in the development of a filamentary structure with a superimposed electrostatic pattern.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗