SEARCH · Engineering Papers

Results for “Wing loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

All sources NASA NTRS DOE OSTI

NASA NTRS1996

A General Interface Method for Aeroelastic Analysis of Aircraft

The aeroelastic analysis of an aircraft requires an accurate and efficient procedure to couple aerodynamics and structures. The procedure needs an interface method to bridge the gap between the aerodynamic and structural models in order to transform loads and displacements. Such an interface method is described in this report. This interface method transforms loads computed by any aerodynamic code to a structural finite element (FE) model and converts the displacements from the FE model to the aerodynamic model. The approach is based on FE technology in which virtual work is employed to transform the aerodynamic pressures into FE nodal forces. The displacements at the FE nodes are then converted back to aerodynamic grid points on the aircraft surface through the reciprocal theorem in structural engineering. The method allows both high and crude fidelities of both models and does not require an intermediate modeling. In addition, the method performs the conversion of loads and displacements directly between individual aerodynamic grid point and its corresponding structural finite element and, hence, is very efficient for large aircraft models. This report also describes the application of this aero-structure interface method to a simple wing and an MD-90 wing. The results show that the aeroelastic effect is very important. For the simple wing, both linear and nonlinear approaches are used. In the linear approach, the deformation of the structural model is considered small, and the loads from the deformed aerodynamic model are applied to the original geometry of the structure. In the nonlinear approach, the geometry of the structure and its stiffness matrix are updated in every iteration and the increments of loads from the previous iteration are applied to the new structural geometry in order to compute the displacement increments. Additional studies to apply the aero-structure interaction procedure to more complicated geometry will be conducted in the second phase of the present contract.

Tzong, T.↗

NASA NTRS2019

How Certain Physical Considerations Impact Aerostructural Wing Optimization

Wing design optimization has been studied extensively and is of continued interest as optimization tools are developed and become more accessible. In each of these studies, certain assumptions and simplifications are made to make the design problem tractable. However, it is difficult to find systematic studies in which several considerations are added or removed one at a time to study how much impact they have. In this work, we examine how certain physical considerations (viscous drag, wave drag, thrust loads, and inertial relief from structural, fuel, and engine masses), impact the aerostructural optimization results for three distinct aircraft wings. The goal is to help develop a rough idea of how important these physical considerations are. We do this using gradient-based optimization and a multidisciplinary design optimization framework, OpenMDAO. We use the open-source tool OpenAeroStruct that couples a vortex lattice method to a finite element method. We establish a baseline aerostructural design optimization problem then perform a series of optimizations, each with one physical consideration removed from the baseline case. We find that depending on the size of the aircraft and flight conditions, the importance of some of these physical considerations varies considerably whereas the importance of others do not. Specifically, the optimal designs change radically without proper viscous and wave drag considerations and smaller aircraft with more distributed propulsion are more affected by the inclusion of engine loads.

Aeropropulsion↗

NASA NTRS2004

International Space Station Solar Array Wing On-Orbit Electrical Performance Degradation Measured

The port-side photovoltaic power module (P6) was activated on the International Space Station in December 2000. P6 provides electrical power to channels 2B and 4B to operate ISS power loads. A P6 is shown in the preceding photograph. This article highlights the work done at the NASA Glenn Research Center to calculate the on-orbit degradation of the P6 solar array wings (SAWs) using on-orbit data from December 2000 to February 2003. During early ISS operations, the 82 strings of photovoltaic cells that make up a SAW can provide much more power than is necessary to meet the demand. To deal with excess power, a sequential shunt unit successively shunts the current from the strings. This shunt current was the parameter chosen for the SAW performance degradation study for the following reasons: (1) it is based on a direct shunt current measurement in the sequential shunt unit, (2) the shunt current has a low temperature dependence that reduces the data correction error from using a computationally derived array temperature, and (3) the SSU shunt current is essentially the same as the SAW short-circuit current on a per-string basis.

Gustafson, Eric D.↗

DOE OSTI2016

Stall Flutter Control of a Smart Blade Section Undergoing Asymmetric Limit Oscillations

Stall flutter is an aeroelastic phenomenon resulting in unwanted oscillatory loads on the blade, such as wind turbine blade, helicopter rotor blade, and other flexible wing blades. Although the stall flutter and related aeroelastic control have been studied theoretically and experimentally, microtab control of asymmetric limit cycle oscillations (LCOs) in stall flutter cases has not been generally investigated. This paper presents an aeroservoelastic model to study the microtab control of the blade section undergoing moderate stall flutter and deep stall flutter separately. The effects of different dynamic stall conditions and the consequent asymmetric LCOs for both stall cases are simulated and analyzed. Then, for the design of the stall flutter controller, the potential sensor signal for the stall flutter, the microtab control capability of the stall flutter, and the control algorithm for the stall flutter are studied. The improvement and the superiority of the proposed adaptive stall flutter controller are shown by comparison with a simple stall flutter controller.

42 ENGINEERING↗

NASA NTRS1975

Design and fabrication of composite wing panels containing a production splice

Bolted specimens representative of both upper and lower wing surface splices of a transport aircraft were designed and manufactured for static and random load tension and compression fatigue testing including ground-air-ground load reversals. The specimens were fabricated with graphite-epoxy composite material. Multiple tests were conducted at various load levels and the results were used as input to a statistical wearout model. The statically designed specimens performed very well under highly magnified fatigue loadings. Two large panels, one tension and compression, were fabricated for testing by NASA-LRC.

Reed, D. L.↗

NASA NTRS1978

A method for predicting full scale buffet response with rigid wind tunnel model fluctuating pressure data. Volume 1: Prediction method development and assessment

The method requires unsteady aerodynamic forces, natural airplane modes, and the measured pressure data as input. A gust response computer program is used to calculate buffet response due to the forcing function posed by the measured pressure data. By calculating both symmetric and antisymmetric solutions, upper and lower bounds on full-scale buffet response are formed. Comparisons of predictions with flight test results are made and the effects of horizontal tail loads and static aeroelasticity are shown. Discussions are also presented on the effects of primary wing torsion modes, chordwise and spanwise phase angles, and altitude.

Cunningham, A. M., Jr.↗

NASA NTRS1982

Elastic deformation effects on aerodynamic characteristics for a high-aspect-ratio supercritical-wing model

The results of an investigation of the deformations of a high-aspect-ratio, force/pressure, supercritical-wing model during wind tunnel tests and the effects these deformations have on the wing aerodynamics are presented. A finite element model of the wing was developed, and then, for conditions corresponding to wind tunnel test points, experimental aerodynamic loads and theoretical aerodynamic loads were applied to the finite element model. Comparisons were made between the results of these load conditions for changes in structural deflections and for changes in aerodynamic characteristics. The results show that the deformations are quite small and that the pressure data are not significantly affected by model deformation.

Watson, J. J.↗

NASA NTRS1991

Development of stitching reinforcement for transport wing panels

The NASA Advanced Composites Technology (ACT) program has the objective of providing the technology required to obtain the full benefit of weight savings and performance improvements offered by composite primary aircraft structures. Achieving the objective is dependent upon developing composite materials and structures which are damage tolerant and economical to manufacture. Researchers are investigating stitching reinforcement combined with resin transfer molding to produce materials meeting the ACT program objective. Research is aimed at materials, processes, and structural concepts for application in both transport wings and fuselages, but the emphasis to date has been on wing panels. Empirical guidelines are being established for stitching reinforcement in structures designed for heavy loads. Results are presented from evaluation tests investigating stitching types, threads, and density (penetrations per square inch). Tension strength, compression strength, and compression after impact data are reported.

Palmer, Raymond J.↗

NASA NTRS1993

Application of a Navier-Stokes aeroelastic method to improve fighter wing performance at maneuver flight conditions

An aeroelastic analysis method, based on three-dimensional Navier-Stokes equation aerodynamics, has been applied to improve the performance of fighter wings operating at sustained maneuver flight conditions. The scheme reduces the trimmed pressure drag of wings performing high-g maneuvers through a simultaneous application of control surface deflection and aeroelastic twist. The aerodynamic and structural interactions are decoupled by assuming an aeroelastic twist mode shape and optimizing the aerodynamic performance based on this aeroelastic mode. The wing structural stiffness properties are then determined through an inverse scheme based on the aerodynamic loads and desired twist at the maneuver flight condition. The decoupled technique is verified by performing a fully coupled aeroelastic analysis using the maneuver flight conditions and the optimized structural stiffness distributions.

Schuster, David M.↗

NASA NTRS1931

The pressure distribution over a semicircular wing tip on an airplane in flight

This note presents the results of flight pressure distribution tests on the right upper wing panel of a Douglas M-3 airplane equipped with a semicircular wing tip. The results are given in tables and curves in such form that the load distribution for any force coefficient within the usual range encountered in flight may easily be determined.

Rhode, Richard V↗

NASA NTRS1939

Pressure-distribution measurements on a rectangular wing with a partial-span split flap in curved flight

Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a rectangular wing of NACA 23012 section to determine the rolling and the yawing moment due to angular velocity in yaw. The model was tested at 0 and 5 degree pitch; 0, +/- 5, and +/- 10 degrees yaw; and with no flap and with split flaps 25, 50 and 75 percent of the wing span and deflected 60 degrees. The results are given in the form of span load distributions and as calculated moment coefficients. The experimental values of rolling- and yawing-moment coefficients were in fairly close agreement with theory.

Rokus, Frank G↗

NASA NTRS1973

Unsteady aerodynamic analysis of space shuttle vehicles. Part 1: Summary report

An analysis of the unsteady aerodynamics of space shuttle vehicles was performed. The results show that slender wing theory can be modified to give the potential flow static and dynamic characteristics over a large Mach number range from M = 0 to M 1. A semi-empirical analytic approximation is derived for the loads induced by the leading edge vortex; and it is shown that the developed analytic technique gives good prediction of experimentally determined steady and unsteady delta wing aerodynamics, including the effects of leading edge roundness. At supersonic speeds, attached leading edge flow is established and shock-induced flow separation effects become of concern. Analysis of experimental results for a variety of boost configurations led to a definition of the main features of the flow interference effects between orbiter (delta wing) and booster. The effects of control deflection on the unsteady aerodynamics of the delta-wing orbiter were also evaluated.

Ericsson, L. E.↗

NASA NTRSDate not supplied

TPSAS-NF1676L-15304-DND

The Subsonic Fixed Wing Project conducts research to improve prediction methods and technologies that will produce lower noise, lower emissions, and higher performing subsonic aircraft for the Next Generation Air Transportation System. Subproject: FW Structural Efficiency: Lightweight, multi-objective and multifunctional structures (e.g., structures that can carry load and attenuate noise at the same time) are being developed to reduce the weight of both airframes and engines. Adaptive and flexible wing structures with aeroelastic tailoring offer significant weight reduction due to the elimination of a heavy actuation system. Extensive use of polymer matrix composites (PMCs) in airframe and engine structures (where applicable) will offer significant weight reduction opportunities. Research on composite technology is focused on developing alternate processes that will enable fabrication of large structures, increasing the temperature capability toward greater usage in engine and supersonic airframe structures, developing advanced structural concepts, and modeling damage initiation and progression in composite structures.

Jason P Moore↗

NASA NTRS1982

Blockage and flow studies of a generalized test apparatus including various wing configurations in the Langley 7-inch Mach 7 Pilot Tunnel

A 1/12th scale model of the Curved Surface Test Apparatus (CSTA), which will be used to study aerothermal loads and evaluate Thermal Protection Systems (TPS) on a fuselage-type configuration in the Langley 8-Foot High Temperature Structures Tunnel (8 ft HTST), was tested in the Langley 7-Inch Mach 7 Pilot Tunnel. The purpose of the tests was to study the overall flow characteristics and define an envelope for testing the CSTA in the 8 ft HTST. Wings were tested on the scaled CSTA model to select a wing configuration with the most favorable characteristics for conducting TPS evaluations for curved and intersecting surfaces. The results indicate that the CSTA and selected wing configuration can be tested at angles of attack up to 15.5 and 10.5 degrees, respectively. The base pressure for both models was at the expected low level for most test conditions. Results generally indicate that the CSTA and wing configuration will provide a useful test bed for aerothermal pads and thermal structural concept evaluation over a broad range of flow conditions in the 8 ft HTST.

Albertson, C. W.↗

NASA NTRS2001

Unified Formulation of the Aeroelasticity of Swept Lifting Surfaces

An unified approach for dealing with stability and aeroelastic response to time-dependent pressure pulses of swept wings in an incompressible flow is developed. To this end the indicial function concept in time and frequency domains, enabling one to derive the proper unsteady aerodynamic loads is used. Results regarding stability in the frequency and time domains, and subcritical aeroelastic response to arbitrary time-dependent external excitation obtained via the direct use of the unsteady aerodynamic derivatives for 3-D wings are supplied. Closed form expressions for unsteady aerodynamic derivatives using this unified approach have been derived and used to illustrate their application to flutter and aeroelastic response to blast and sonic-boom signatures. In this context, an original representation of the aeroelastic response in the phase space was presented and pertinent conclusions on the implications of some basic parameters have been outlined.

Silva, Walter↗

NASA NTRS1976

Theoretical Stability and Control Characteristics of Wings With Various Amounts of Taper and Twist

Stability derivatives have been computed for twisted wings of different planforms that include variations in both the wing taper and the aspect ratio. Taper ratios of 1.0, 0.50, and 0.25 are considered for each of three aspect ratios: 6, 10, and 16. The specific derivatives for which results are given are the rolling moment and the yawing moment derivatives with respect to rolling velocity, yawing velocity, and angle of sideslip. In addition to the stability derivatives, results are included for determining the theoretical rolling moment due to aileron deflection and a series of influence lines is given by which the loading across the span may be determined for any angle-of-attack distribution that may occur on the wing planforms considered.

Henry A Pearson↗

NASA NTRS1981

Development of an efficient procedure for calculating the aerodynamic effects of planform variation

Numerical procedures to compute gradients in aerodynamic loading due to planform shape changes using panel method codes were studied. Two procedures were investigated: one computed the aerodynamic perturbation directly; the other computed the aerodynamic loading on the perturbed planform and on the base planform and then differenced these values to obtain the perturbation in loading. It is indicated that computing the perturbed values directly can not be done satisfactorily without proper aerodynamic representation of the pressure singularity at the leading edge of a thin wing. For the alternative procedure, a technique was developed which saves most of the time-consuming computations from a panel method calculation for the base planform. Using this procedure the perturbed loading can be calculated in about one-tenth the time of that for the base solution.

Mercer, J. E.↗

NASA NTRS1997

Experiments in Aircraft Roll-Yaw Control using Forebody Tangential Blowing

Advantages of flight at high angles of attack include increased maneuverability and lift capabilities. These are beneficial not only for fighter aircraft, but also for future supersonic and hypersonic transport aircraft during take-off and landing. At high angles of attack the aerodynamics of the vehicle are dominated by separation, vortex shedding and possibly vortex breakdown. These phenomena severely compromise the effectiveness of conventional control surfaces. As a result, controlled flight at high angles of attack is not feasible for current aircraft configurations. Alternate means to augment the control of the vehicle at these flight regimes are therefore necessary. The present work investigates the augmentation of an aircraft flight control system by the injection of a thin sheet of air tangentially to the forebody of the vehicle. This method, known as Forebody Tangential Blowing (FTB), has been proposed as an effective means of increasing the controllability of aircraft at high angles of attack. The idea is based on the fact that a small amount of air is sufficient to change the separation lines on the forebody. As a consequence, the strength and position of the vortices are altered causing a change on the aerodynamic loads. Although a very effective actuator, forebody tangential blowing is also highly non-linear which makes its use for aircraft control very difficult. In this work, the feasibility of using FTB to control the roll-yaw motion of a wind tunnel model was demonstrated both through simulations and experimentally. The wind tunnel model used in the experiments consists of a wing-body configuration incorporating a delta wing with 70-degree sweep angle and a cone-cylinder fuselage. The model is equipped with forebody slots through which blowing is applied. There are no movable control surfaces, therefore blowing is the only form of actuation. Experiments were conducted at a nominal angle of attack of 45 degrees. A unique apparatus that constrains the model to two degrees-of-freedom, roll and yaw, was designed and built. The apparatus was used to conduct dynamic experiments which showed that the system was unstable, its natural motion divergent. A model for the unsteady aerodynamic loads was developed based on the basic physics of the flow and results from flow visualization experiments. Parameters of the aerodynamic model were identified from experimental data. The model was validated using data from dynamic experiments. The aerodynamic model completes the equations of motion of the system which were used in the design of control laws using blowing as the only actuator. The unsteady aerodynamic model was implemented as part of the real-time vehicle control system. A control strategy using asymmetric blowing was demonstrated experimentally. A discrete vortex method was developed to help understand the main physics of the flow. The method correctly captures the interactions between forebody and wing vortices. Moreover, the trends in static loads and flow structure are correctly represented. Flow visualization results revealed the vortical structure of the flow to be asymmetric even for symmetric flight conditions. The effects of blowing, and roll and yaw angles on the flow structure were determined. It is shown that superimposing symmetric and asymmetric blowing has a linearizing effect on the actuator characteristics. Transient responses of roll and yaw moments to step input blowing were characterized, and their differences were explained based on the physical mechanisms through which these loads are generated.

Pedreiro, Nelson↗