Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ta”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improved Creep and Tensile Properties of a Corrosion Resistant Ni-Based Superalloy Using High Temperature Aging and Nb/Ta Additions

Resistance to creep deformation is essential for cast and wrought Ni-based superalloys in next generation energy systems due to the considerable exposure times required at the operating temperature. Here the amount of precipitate strengthening was increased in variants to Inconel alloy 725 (IN725), a corrosion resistant alloy, to improve its elevated temperature mechanical strength. Additions of Nb or Ta coupled with a high temperature aging (HTA) heat treatment promoted the formation of γ" precipitates and grain boundary phases which led to significant increases in time to failure. The HTA increased the creep life of various alloy formulations as compared to the standard aging heat treatment with a maximum improvement of 371%. The Nb and Ta additions lowered the minimum creep rate (MCR) and had a similar effect on increasing creep life. The positive effect of the additions was more pronounced when coupled with the HTA which employed a higher temperature in the first step of the heat treatment to promote precipitate phase formation. The Ti/Al ratio was used to design alloys with preferential formation of ' or γ" precipitates. Compact morphology precipitates were formed in the alloys with a low Ti/Al ratio. While a low Ti/Al ratio was primarily associated with lower MCRs, the effect on the creep life was less evident than that of the HTA. By using additions of Nb or Ta and a HTA heat treatment, the creep life of IN725 for testing at 973 K (700 °C) and 483 MPa was improved by up to 256%.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Near-Surface Layer Perforations as Precursors to Fracture in Accumulative Roll Bonding of a Multilayered Metal Composite

We use micro-computed tomography (µ-CT) to characterize the sizes, shapes, and locations of layer perforation (LP) defects in laminates of copper (Cu) and tantalum (Ta) processed by accumulative roll bonding (ARB). One—termed Cu/Ta—was processed from an initial stacking of seven alternating Cu and Ta sheets, with the exterior sheets being Cu. In the other—termed Ta/Cu—the exterior sheets are Ta. Cu/Ta remained intact during processing and exhibits an approximately uniform spatial distribution of LPs. By contrast, Ta/Cu fractured by longitudinal splitting. LPs in this latter sample are concentrated near the sample surfaces. Moreover, their density increases with decreasing distance to the fracture surface. Furthermore, these findings show that materials undergoing ARB may remain intact, despite profuse formation of LPs, provided that the LPs are uniformly distributed. However, a non-uniform distribution of LPs is correlated with longitudinal splitting.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-throughput exploration of the WMoVTaNbAl refractory multi-principal-element alloys under multiple-property constraints

Development of next-generation gas turbines requires the design and fabrication of novel high-temperature structural materials capable of operating beyond 1300°C. Here, we propose a high-throughput alloy design framework under multiple-property constraints to discover new refractory multi-principal element alloys (MPEAs) for high-temperature applications. The framework treats the development of MPEAs as a composition-agnostic constraint satisfaction problem, i.e., no prescriptions are made concerning the design space before performing investigatory calculations. We target alloys in the WMoVTaNbAl chemistry space that are predicted to meet constraints on the following properties simultaneously: single-phase stability, density, solidus temperature, yield strength at 1300°C, and ductile-to-brittle-transition temperature. These properties are relevant to both applications in gas turbines and manufacturability. A set of 214 MoNbV-rich alloys meet these relevant constraints. These feasible alloys are investigated with density functional theory (DFT) to provide a fundamental electronic basis for their superior properties. Three compositionally representative alloys from the feasible design space (Mo 45 Nb 35 Ta 5 V 15 , Mo 25 Nb 50 V 20 W 5 , and Mo 30 Nb 35 Ta 5 V 25 W 5 ) are selected with a k-medoids-based design scheme for detailed DFT analysis and experimental characterization. The DFT analysis predicted a single-phase BCC at high temperatures with a high yield strength for all three MPEAs, in agreement with CALPHAD (CALculation of PHAse Diagrams) and experiments, respectively. These three alloys are benchmarked against a public database of 1546 MPEAs. Concerning the aforementioned constraints, the Mo 30 Nb 35 Ta 5 V 25 W 5 alloy outperforms these 1546 MPEAs. The present work demonstrates the ability of the proposed design methodology to identify candidate alloys for a given application under multiple property constraints in a combinatorically vast design space.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A plausible method of preparing the ideal p-n junction interface of a thermoelectric material by surface doping

Recent advances in two-dimensional (2D) crystals make it possible to realize an ideal interface structure that is required for device applications. Specifically, a p-n junction made of 2D crystals is predicted to exhibit an atomically well-defined interface that will lead to high device performance. Using angle-resolved photoemission spectroscopy, a simple surface treatment was shown to allow the possible formation of such an interface. Furthermore, Ta adsorption on the surface of a p-doped SnSe shifts the valence band maximum towards the higher binding energy due to the charge transfer from Ta to SnSe that is highly localized at the surface due to the layered structure of SnSe. As a result, the charge carriers of the surface are changed from holes of its bulk characteristics to electrons, while the bulk remains as a p-type semiconductor. This observation suggests that the well-defined interface of a p-n junction with an atomically thin n-region is formed between Ta-adsorbed surface and bulk.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of phase-transformation path in TiZrHf(VNbTa)x refractory high-entropy alloys and its effect on mechanical property

Refractory high-entropy alloys (RHEAs) show a great potential as structural materials due to their remarkable properties, such as high strength and thermal stability. Despite these advantages, the RHEAs still suffer from the limited ductility at room temperature. To overcome the strength-ductility trade-off, the new RHEA design strategy, transformation-induced plasticity (TRIP) HEAs, have been developed by applying metastability-engineering approach. With the newly developed RHEAs design strategy, we designed metastable RHEAs, TiZrHfVxNbxTax (x = 1.0, 0.5 and 0.1) with decrease of the β-stabilizing elements (V, Nb, and Ta) to promote the transformation-induced ductility and work-hardening capability. The proper addition of the β-stabilizing elements (V, Nb, and Ta) into the ternary equi-molar TiZrHf alloy (TiZrHfV 0.1 Nb 0.1 Ta 0.1 ) leads to stress/strain-induced phase transformation from the body-centered cubic (BCC) to hexagonal-close-packed (HCP) α' and/or orthorhombic α" phases. Here, detailed studies on the phase transformation sequence during the deformation were carried out using X-ray diffraction (XRD), electron back-scattered diffraction (EBSD), and transmission-electron microscope (TEM), which revealed the stepwise phase transformation that is responsible for the strong strain hardening behavior. Furthermore, we further suggested the new transformation-induced-plasticity (TRIP) HEA design strategy, applying the Bo-Md approach.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Gas nitriding behavior of refractory metals and implications for multi-principal element alloy design

Multi-principal element alloys (MPEAs) comprise a large, flexible compositional space that enables tuning of their chemistry, structure, and properties. Here, to facilitate the development of nitriding-based surface-enhancement strategies that harness a broad compositional space, this study examined the gas nitriding behavior of Hf, Mo, Nb, Ta, Ti, and Zr as a function of time, temperature (750 and 1000 °C), and nitriding potential (i.e. ammonia-to-hydrogen ratio). These metals were selected because they have a strong driving force to form nitrides, and appear in many promising refractory MPEA compositions. The nitriding temperatures were selected based on the phase transformation temperature of Ti and Zr, and the nitriding potentials were chosen such that all elements are expected to form nitrides. Mass gain measurements indicate that all six elements follow parabolic kinetics. The microstructure observations and quantitative microchemical analysis show formation of dense and well-adhered compound layers for Mo, Nb, and Ta. Thick diffusion zones appear in Hf, Ta, Ti, and Zr, and diffusion coefficients were fit to the composition profiles. Partial delamination of the compound layer occurred for Ti and Zr. Peak hardness values above 30 GPa are obtained in the dense compound layers, and the solute hardening of the underlying alloy is correlated with the nitrogen content. The results provide insight into the dynamics of nitride compound formation relative to interstitial dissolution of nitrogen, and are discussed in the context of MPEA composition and processing design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗
DOE OSTI2024

Post-irradiation examination of commercial tantalum alloys following neutron irradiation

Post irradiation examination of two commercial tantalum alloys (based on Ta-8 %W) revealed significant irradiation hardening following neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Tensile samples of commercial Ta alloys T-111 and ASTAR-811C were irradiated to a total neutron fluence (E > 0.1 MeV) in the range (2–4)x10 21 n/cm 2 (0.39–0.75 dpa) at an irradiation temperature near 900 °C. Tensile testing conducted at room temperature and at 800 °C revealed significant irradiation hardening under all test conditions. Samples that were tensile tested at room temperature exhibited brittle failure, whereas ductility was maintained for elevated temperature testing. The irradiation hardening and embrittlement noted for both alloys was attributed to irradiation-induced dislocation loop formation as confirmed through scanning transmission electron microscopy analysis. Corresponding energy dispersive x-ray spectroscopy revealed radiation-induced segregation of Hf in these loop populations. This Hf enrichment is shown to result in eventual co-precipitation of elongated (Hf,O)-rich precipitates along the dislocation loops. Further, these results show that irradiation hardening is enhanced via irradiation-enhanced precipitation at elevated irradiation temperatures. Consequently, the minimum recommended operating temperature window for Ta alloys should be increased to account for observed hardening/embrittlement at irradiation temperatures as high as 900 °C (1,173 K).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of niobium and tantalum on the microstructure and strength of ferritic-martensitic steels

Herein, detailed investigations of two ferritic-martensitic steels, i.e., Nb- and Ta-steel, indicate that the higher Nb diffusivity and the lower nucleation driving force of Nb-carbide promote preferential nucleation of Nb-carbides at grain boundaries and thus a higher boundary occupancy than Ta-carbides, which favored greater creep resistance of Nb-steel than that of Ta-steel despite their similar yield strength.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Nuclear Data Sheets for A=190

The evaluated experimental data are presented and evaluated for 15 known nuclides of mass 190 (Hf, Ta, W, Re, Os, Ir, Pt, Au, Hg, Tl, Pb, Bi, Po). This work supersedes earlier full evaluations of A=190 by 2003Si05, 1990Si09, 1982Le22 and 1973Sc42. For 190Hf, only the isotopic identification has been made, with no information about the half-life of the ground state or its decay properties. For 190 Ta, only one excited state as an isomer has been identified, but with no knowledge about its decay properties. For 190 W, 190 Re, 190 Bi and 190 Po, available spectroscopic data are scarce. Here, the decay schemes of 190 Ta, 190 W, 190 Au, 190 Hg, 190 Au isomer decay, 190 Tl (both the activities), 190 Pb, and 190 Bi (both the activities) are considered incomplete by the evaluators. At present, extensive level structures, both the low-spin and high-spin, are known for 190 Os, 190 Ir, 190 Pt, 190 Au, 190 Hg, 190 Tl and 190 Pb, but data for level lifetimes, and γ-ray transition probabilities are generally lacking.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Direct WIMP detection rates for transitions in isomeric nuclei

The direct detection of dark matter constituents, in particular the weakly interacting massive particles (WIMPs), is central to particle physics and cosmology. In this paper we study WIMP induced transitions from isomeric nuclear states for two possible isomeric candidates: 180 Ta and 166 Ho. The experimental setup, which can measure the possible decay of 180 Ta induced by WIMPs, was proposed. The corresponding estimates of the half-life of 180 Ta are given in the sense that the WIMP-nucleon interaction can be interpreted as ordinary radioactive decay.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Tantalum oxide and nitride spectral features from a laser-produced plasma

Here, we report measurements of time-resolved Ta, TaO and TaN emission spectroscopic signatures from a laser-produced plasma. Plasmas were generated using 1064 nm, 6 ns pulses from an Nd:YAG laser focused onto a pure Ta metal target in a gaseous environment with varying percentages of O 2 /N 2 for controlling gas-phase oxidation/plasma chemistry. Time-resolved analysis showed that Ta oxide emission is prominent at later times in plasma evolution, whereas strong atomic emission is present at early times in air. Emission spectral features as a function of O 2 partial pressure showed that TaO emission intensity increases, while the peak intensity of TaO appears earlier with increasing O 2 availability. We also report emission spectra of TaN, and show that plasma chemistry favors TaO formation instead of TaN when O 2 is present in the environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Nanotubes from the Misfit Layered Compound (SmS) 1.19 TaS 2 : Atomic Structure, Charge Transfer, and Electrical Properties

Misfit layered compounds (MLCs) MX-TX 2 , where M, T = metal atoms and X = S, Se, or Te, and their nanotubes are of significant interest due to their rich chemistry and unique quasi-1D structure. In particular, LnX-TX 2 (Ln = rare-earth atom) constitute a relatively large family of MLCs, from which nanotubes have been synthesized. The properties of MLCs can be tuned by the chemical and structural interplay between LnX and TX 2 sublayers and alloying of each of the Ln, T, and X elements. In order to engineer them to gain desirable performance, a detailed understanding of their complex structure is indispensable. MLC nanotubes are a relative newcomer and offer new opportunities. In particular, like WS 2 nanotubes before, the confinement of the free carriers in these quasi-1D nanostructures and their chiral nature offer intriguing physical behavior. High-resolution transmission electron microscopy in conjunction with a focused ion beam are engaged to study SmS-TaS 2 nanotubes and their cross-sections at the atomic scale. The atomic resolution images distinctly reveal that Ta is in trigonal prismatic coordination with S atoms in a hexagonal structure. Furthermore, the position of the sulfur atoms in both the SmS and the TaS 2 sublattices is revealed. X-ray photoelectron spectroscopy, electron energy loss spectroscopy, and X-ray absorption spectroscopy are carried out. These analyses conclude that charge transfer from the Sm to the Ta atoms leads to filling of the Ta 5d z 2 level, which is confirmed by density functional theory (DFT) calculations. Transport measurements show that the nanotubes are semimetallic with resistivities in the range of 10 –4 Ω·cm at room temperature, and magnetic susceptibility measurements show a superconducting transition at 4 K.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced Twist-Averaging Technique for Magnetic Metals: Applications Using Quantum Monte Carlo

In this study, we propose an improved twist-averaging (TA) scheme for quantum Monte Carlo methods that use converged Kohn–Sham or Hartree–Fock orbitals as the reference. This TA technique is tailored to sample the Brillouin zone of magnetic metals, although it naturally extends to nonmagnetic (NM) conducting systems. The proposed scheme aims to reproduce the reference magnetization and achieves charge neutrality by construction, thus avoiding the large energy fluctuations and the postprocessing needed to correct the energies. It shows the most robust convergence of total energy and magnetism to the thermodynamic limit (TDL) when compared to four other TA schemes. Diffusion Monte Carlo applications are shown on NM Al and ferromagnetic α-Fe. The cohesive energy of Al in the TDL shows an excellent agreement with the experimental result. Furthermore, the magnetic moments in α-Fe exhibit rapid convergence with an increasing number of twists.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The Impact of Carotenoid Energy Levels on the Exciton Dynamics and Singlet–Triplet Annihilation in Isolated Bacterial Light-Harvesting 2 Complexes

The light-harvesting 2 (LH2) complex of purple phototrophic bacteria plays a critical role in absorbing solar energy and distributing the excitation energy. Exciton dynamics within LH2 complexes are controlled by the structural arrangement and energy levels of the bacteriochlorophyll (BChl) and carotenoid (Car) pigments. However, there is still debate over the competing light-harvesting versus energy-dissipation pathways. In this work, we compared five variants of the LH2 complex from genetically modified strains of Rhodobacter sphaeroides, all containing the same BChls but different Cars with increasing conjugation: zeta-carotene (N = 7; LH2 Zeta ), neurosporene (N = 9; LH2 Neu ), spheroidene (N = 10; LH2 Spher ), lycopene (N = 11; LH2 Lyco ), and spirilloxanthin (N = 13; LH2 Spir ). Absorption measurements confirmed that the Car excited-state energy decreased with increasing conjugation. Similarly, fluorescence spectra showed that the B850 BChl emission peak had an increasing red shift from LH2 Zeta →(LH2 Neu /LH2 Spher )→LH2 Lyco →LH2 Spir . In contrast, time-resolved fluorescence and ultrafast transient absorption (fs-TA) revealed similar excited-state lifetimes (∼1 ns) for all complexes except LH2 Spir (∼0.7 ns). From fs-TA analysis, an additional ∼7 ps nonradiative dissipation step from B850 BChl was observed for LH2 Zeta . Further, singlet− singlet and singlet−triplet annihilation studies showed a ∼50% average fluorescence lifetime reduction in LH2Zeta at high laser power and high repetition rate, compared to ∼10−15% reductions in LH2 Neu /LH2 Spher /LH2 Lyco and minimal lifetime change in LH2 Spir . In LH2 Zeta , the fastest decay component (<50 ps) became prominent at high repetition rates, consistent with strong singlet−triplet annihilation. Nanosecond TA measurements revealed long-lived (>40 μs) BChl triplet states in LH2 Zeta and signs of damage caused by singlet oxygen, whereas other LH2s showed faster triplet quenching (∼18 ns) by Cars. These findings highlight a key design principle of LH2 complexes: the Car triplet energy must be significantly lower than the BChl triplet energy to efficiently quench BChl triplets that otherwise act as potent “trap states,” causing exciton annihilation in laser-based experiments or photodamage in native membranes.

Absorption↗
DOE OSTI2020

Distinguishing Electron and Hole Dynamics in Functionalized CdSe/CdS Core/Shell Quantum Dots Using Complementary Ultrafast Spectroscopies and Kinetic Modeling

The evolution of excitation energy and photogenerated charges in semiconductor quantum dots (QDs) functionalized with molecular acceptors can be probed on ultrafast time scales using techniques such as transient absorption (TA) spectroscopy. However, historical interpretations that the 1S(e)-1S 3/2 (h) transition in Cd-chalcogenide QDs is fully attributable to electrons may be misleading, and multiexponential models used to fit TA kinetics do not correspond directly to specific photophysical processes. Here, we present visible-wavelength and mid-IR TA and time-resolved photoluminescence measurements to inform a comprehensive kinetic model of the photoexcited CdSe/CdS core/shell QDs functionalized with passivating oleic acid (OA), hole-accepting ferrocene, or electron-accepting naphthalene bisimide (NBI). We show that ~30% of the 1S signal and 72% of the IR signal can originate from holes in well-passivated core/shell QDs. We also demonstrate evidence of electron trapping in OA-capped core/shell QDs, with additional electron transfer and hole trapping in the QDs functionalized with NBI. Electron (hole) trapping and detrapping occur in 450 ± 100 ps (430 ± 70 ps) and 340 ± 100 ps (1.1 ± 0.4 ns) respectively, while the time constant for electron transfer to NBI is ~1.8 ns. The comprehensive picture of photophysical processes provided by the complementary ultrafast techniques and kinetic modeling can accelerate both the fundamental science and application development of nanostructured and molecular systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Complex Fluorine Chemical Potential Effects on the Shape and Compositional Heterogeneity of KTa 1– x Nb x O 3 Nanoparticles

When kinetic conditions dominate and dictate the growth in a nanoparticle synthesis, properties of the synthesis environment can have considerable effects on the properties of the products. Such effects were studied here, where the solution environment was changed via the addition of KF to the hydrothermal syntheses of KTa 1– x Nb x O 3 and KTaO 3 . One result demonstrated the straightforward cause-and-effect relationship between the solution and reaction kinetics: KF directly increased the solution stability of the Ta species and therefore decreased its reaction rate, resulting in a change in composition heterogeneity of Ta and Nb in the KTa 1– x Nb x O 3 particles. However, not all effects are so simple; changing the chemical potential of the solution with KF can also promote the formation of particles with anisotropic defect enhanced kinetic Wulff shapes instead of cuboidal shapes. The increased F chemical potential in the solution enabled the formation of planar defects in the bulk, which accelerated growth in-plane to form particles characterized by flat rectangular flake geometries. In this work, thermodynamic modeling with density functional theory calculations confirmed that sufficient KF concentrations can drive the formation of a defect phase K n +1 Ta n O 3 n F.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗