Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUBING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Kinematics and dynamics of vortex rings in a tube

Kinematic theory and flow visualization experiments were combined to examine the dynamic processes which control the evolution of vortex rings from very low to very high Reynolds numbers, and to assess the effects of the wall as a vortex ring travels up a tube. The kinematic relationships among the size, shape, speed, and strength of vortex rings in a tube were computed from the theory. Relatively simple flow visualization measurements were used to calculate the total circulation of a vortex rings at a given time. Using this method, the strength was computated and plotted as a function of time for experimentally produced vortex rings. Reynolds number relationships are established and quantitative differences among the three Reynolds number groups are discussed.

Brasseur, J. G.↗

Performance of photomultiplier tubes and sodium iodide scintillation detector systems

The performance of photomultiplier tubes (PMT's) and scintillation detector systems incorporating 50.8 by 1.27 cm NaI (T l) crystals was investigated to determine the characteristics of the photomultiplier tubes and optimize the detector geometry for the Burst and Transient Source Experiment on the Gamma Ray Observatory. Background information on performance characteristics of PMT's and NaI (T l) detectors is provided, procedures for measurement of relevant parameters are specified, and results of these measurements are presented.

Meegan, C. A.↗

Velocity and concentration distribution in a Stefan diffusion tube

Numerical solutions for the diffusion- and gravity-driven flow in a cylindrical Stefan tube were obtained from the coupled diffusion and Navier-Stokes equations of Peclet numbers 0.3, 1 and 5. Distributions of binary component concentrations and velocities were calculated. The mass average velocity is parabolic in nature, except at high Peclet numbers. The solvent is not stagnant but recirculates, even in the absence of gravity. Radial concentration gradients develop which act convectively destabilizing. Consequences for the deduction of diffusion coefficients from Stefan tube experiments are discussed.

Markham, B. L.↗

Containerless undercooling and solidification in drop tubes

A containerless low-gravity environment, produced within a 32 m drop tube apparatus, has been used to undercool and solidify metals, alloys or glasses by eliminating crucible induced nucleation processes. Niobium droplets with diameters in the range of 2 to 5 mm have been undercooled by 525 K which corresponds to the maximum undercooling reported by Turnbull and others on fine dispersions of low melting point metals. Solidification at large undercooling resulted in single crystalline spheres with the formation of interdendritic shrinkage channels on the sample surface rather than interior shrinkage cavities. The grain refinement as observed for Ni samples undercooled and solidified in fused silica crucibles does not occur in free-falling drops of Nb. A calculated solidification speed of undercooled Nb is compared to Ni. A solidification speed of 320 m/s is found for the Nb drops. This solidification speed is greater than or comparable to the solidification speeds calculated in splat cooled samples. Thus, a drop tube apparatus can be useful in the preparation and study of high temperature metastable compounds or alloys in bulk form.

Lacy, L. L.↗

Tubing Cutter is Activated Hydraulically

Hydraulically-actuated tubing cutter severs tubing when operator squeezes handle grip. "Gooseneck" extension enables cutter to be used in areas where accessiblity is limited. Cutter has potential as flight-line tool and is useful in automobile and fire rescue work.

Mcsmith, D. G.↗

Correlation of transonic-cone Preston-tube data and skin friction

The distribution of Preston tube pressures within turbulent boundary layers along the surface of a sharp-nosed, ten degree cone was correlated with theoretical values of turbulent skin friction for freestream Mach numbers less than one. The mini-basic computer code, the Wu and Lock computer code, and the STAN-5 computer code were used to analyze the data and to solve the boundary layer conservation equations. The skin friction which results from using Preston tube pressures in the correlation equation, has a rms error of 1.125 percent. It was found that the effective center of the probe is not a constant but increases as the surface distance increases. For a specified unit Reynolds number, the effective center of the probe decreases as the Mach number increases. The variation of the fluid (air) properties across the face of the probe may be neglected for subsonic flows. The possible transverse errors caused by the use of the concept of a virtual origin for the turbulent boundary layer were investigated and found to be negligible.

Reed, T. D.↗

Diffusion tube

The diffusion tube was designed to operate below about 0.25 percent of water supersaturation. It is simply a long tube lined on the inside with a damp chamois cloth, and heated isothermally to a few degrees centigrade above the incoming air. The diffusion coefficient for water vapor is slightly larger than that for heat, making it possible to supersaturate the airflow. This is the same principle by which transient supersaturations may occur in parallel plate cloud chambers. Only the diffusion of vapor and heat from the walls into the moving air are considered.

Leaitch, R.↗

Effect of oxide films on hydrogen permeability of candidate Stirling engine heater head tube alloys

The effect of oxide films developed in situ from CO/CO2 doped hydrogen on high pressure hydrogen permeability at 820 C was studied on N-155, A-286, IN 800, 19-9DL, Nitronic 40, HS-188, and IN 718 tubing in a Stirling materials simulator. The hydrogen permeability decreased with increasing dopant levels of CO or CO2 and corresponding decreases in oxide porosity. Minor reactive alloying elements strongly influenced permeability. At high levels of CO or CO2, a liquid oxide formed on alloys with greater than 50 percent Fe. This caused increased permeability. The oxides formed on the inside tube walls were analyzed and their effective permeabilities were calculated.

Schuon, S. R.↗

Study of boundary-layer transition using transonic cone Preston tube data

Laminar layer Preston tube data on a sharp nose, ten degree cone obtained in the Ames 11 ft TWT and in flight tests are analyzed. During analyses of the laminar-boundary layer data, errors were discovered in both the wind tunnel and the flight data. A correction procedure for errors in the flight data is recommended which forces the flight data to exhibit some of the orderly characteristics of the wind tunnel data. From corrected wind tunnel data, a correlation is developed between Preston tube pressures and the corresponding values of theoretical laminar skin friction. Because of the uncertainty in correcting the flight data, a correlation for the unmodified data is developed, and, in addition, three other correlations are developed based on different correction procedures. Each of these correlations are used in conjunction with the wind tunnel correlation to define effective freestream unit Reynolds numbers for the 11 ft TWT over a Mach number range of 0.30 to 0.95. The maximum effective Reynolds numbers are approximately 6.5% higher than the normal values. These maximum values occur between freestream Mach numbers of 0.60 and 0.80. Smaller values are found outside this Mach number range. These results indicate wind tunnel noise affects the average laminar skin friction much less than it affects boundary layer transition. Data on the onset, extent, and end of boundary layer transition are summarized. Application of a procedure for studying the relative effects of varying nose radius on a ten degree cone at supercritical speeds indicates that increasing nose radius promotes boundary layer transition and separation of laminar boundary layers.

Reed, T. D.↗

Correlation of Preston-tube data with laminar skin friction (Log No. J12984)

Preston tube data within laminar boundary layers obtained on a sharp ten-degree cone in the NASA Ames eleven-foot transonic wind tunnel are correlated with the corresponding values of theoretical skin friction. Data were obtained over a Mach number range of 0.30 to 0.95 and unit Reynolds numbers of 9.84, 13.1, and 16.4 million per meter. The rms scatter of skin friction coefficient about the correlation is of the order of one percent, which is comparable to the reported accuracy for calibrations of Preston tubes in incompressible pipe flows. In contrast to previous works on Preston tube/skin friction correlations, which are based on the physical height of the probe's face, this satisfactory correlation for compressible boundary layer flows is achieved by accounting for the effects of a variable "effective" height of the probe. The coefficients, which appear in the correlation, are dependent on the particular tunnel environment. The general procedure can be used to define correlations for other wind tunnels.

Reed, T. D.↗

Alfven waves in the solar atmosphere. III - Nonlinear waves on open flux tubes

Consideration is given the nonlinear propagation of Alfven waves on solar magnetic flux tubes, where the tubes are taken to be vertical, axisymmetric and initially untwisted and the Alfven waves are time-dependent axisymmetric twists. The propagation of the waves into the chromosphere and corona is investigated through the numerical solution of a set of nonlinear, time-dependent equations coupling the Alfven waves into motions that are parallel to the initial magnetic field. It is concluded that Alfven waves can steepen into fast shocks in the chromosphere, pass through the transition region to produce high-velocity pulses, and then enter the corona, which they heat. The transition region pulses have amplitudes of about 60 km/sec, and durations of a few tens of seconds. In addition, the Alfven waves exhibit a tendency to drive upward flows, with many of the properties of spicules.

Hollweg, J. V.↗

Apollo 17 drive tube 76001 - Modal petrology

Twelve polished thin sections from Apollo 17 drive tube 76001 have been studied by optical petrography. The entire core is found to be mature showing little variation in depth, which is consistent with a depositional model involving slow downslope movement of the regolith by mass wasting. However, within the core some major differences are preserved between two stratigraphic units. Unit A (20-31 cm depth) is enriched in gabbroic anorthosite relative to unit B (0-20 cm depth), while unit B is enriched in KREEPY noritic breccias relative to unit A. This observation is interpreted in terms of a stratigraphy for North Massif involving a noritic breccia unit overlying a unit enriched in gabbroic anorthosite. Pronounced differences between the highland/mare ratios in drive tube 76001 and the Apollo 17 drill core separated by only 3.5 km demonstrate the relative inefficiency of lateral transport as a regolith mixing mechanism on the moon.

Papike, J. J.↗

Heat transfer from combustion gases to a single row of closely spaced tubes in a swirl crossflow Stirling engine heater

This paper describes an experimental program to determine the heat-transfer characteristics of a combustor and heat-exchanger system in a hybrid solar receiver which utilizes a Stirling engine. The system consists of a swirl combustor with a crossflow heat exchanger composed of a single row of 48 closely spaced curved tubes. In the present study, heat-transfer characteristics of the combustor/heat-exchanger system without a Stirling engine have been studied over a range of operating conditions and output levels using water as the working fluid. Nondimensional heat-transfer coefficients based on total heat transfer have been obtained and are compared with available literature data. The results show significantly enhanced heat transfer for the present geometry and test conditions. Also, heat transfer along the length of the tubes is found to vary, the effect depending upon test condition.

Bankston, C. P.↗

Eddy-Current Inspection of Narrow Metal Tubes

Inspection technique for narrow-bore metal tubing involves use of small internal eddy-current probe. Probe consists of thin copper wire wrapped on bobbin. Probe small enough to pass through bends in tube being measured. Technique useful for strain measurements where operating conditions or inaccessibility prevent use of such conventional methods as X-ray diffraction, electrical-resistance measurements, strain gages, or holography.

Ambrose, H. H.↗

Lock for Tube Fittings

Attachment for nuts of tube fittings locks fittings securely. Attachment includes covers for nut on tube fitting and nut on boss fitting.

Hein, L. A.↗

Hydraulic Tube Expander

Portable hydraulic tube expander expands small, thick-walled tubes in hard-to-reach locations. Tool particularly useful in situations where mechanical expander too fragile to produce desired expansion.

Burley, R. K.↗

Repairing Hidden Cracks in Coolant Tubes

Repair technique closes leaks in tubes or conduits where access limited to wall opposite crack. Technique applicable to any tubular assembly where tubes bundled together or bonded to supporting shell, such as in heat exchangers. Procedure provides structural support to area failed and uninterrupted flow without significantly altering heat-transfer profile.

Mills, R. C., Sr.↗

Welding Tubes In Place

Special welding equipment joins metal tubes that carry pressurized cyrogenic fluids. Equipment small enough to be used in confined spaces in which such tubes often mounted. Welded joints lighter in weight and more leak-proof than joints made with mechanical fittings.

Meredith, R.↗