Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRAILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Blade-to-coolant heat-transfer results and operating data from a natural-convection water-cooled single-stage turbine

Blade-to-coolant heat-transfer data and operating data were obtained with a natural-convection water-cooled turbine over range of turbine speeds and inlet-gas temperatures. The convective coefficients were correlated by the general relation for natural-convection heat transfer. The turbine data were displaced from a theoretical equation for natural convection heat transfer in the turbulent region and from natural-convection data obtained with vertical cylinders and plates; possible disruption of natural convection circulation within the blade coolant passages was thus indicated. Comparison of non dimensional temperature-ratio parameters for the blade leading edge, midchord, and trailing edge indicated that the blade cooling effectiveness is greatest at the midchord and least at the trailing edge.

COOLING - GAS TURBINE SYSTEMS↗

Preliminary wing model tests in the variable density wind tunnel of the National Advisory Committee for Aeronautics

This report contains the results of a series of tests with three wing models. By changing the section of one of the models and painting the surface of another, the number of models tested was increased to five. The tests were made in order to obtain some general information on the air forces on wing sections at a high Reynolds number and in particular to make sure that the Reynolds number is really the important factor, and not other things like the roughness of the surface and the sharpness of the trailing edge. The few tests described in this report seem to indicate that the air forces at a high Reynolds number are not equivalent to respective air forces at a low Reynolds number (as in an ordinary atmospheric wind tunnel). The drag appears smaller at a high Reynolds number and the maximum lift is increased in some cases. The roughness of the surface and the sharpness of the trailing edge do not materially change the results, so that we feel confident that tests with systematic series of different wing sections will bring consistent results, important and highly useful to the designer.

Munk, Max M↗

Theoretical calculations of the pressure, forces, and moments at supersonic speeds due to various lateral motions acting on thin isolated vertical tails

Velocity potentials, pressure, distributions, and stability derivatives are derived by use of supersonic linearized theory for families of thin isolated vertical tails performing steady rolling, steady yawing, and constant-lateral-acceleration motions. Vertical-tail families (half-delta and rectangular plan forms) are considered for a broad Mach number range. Also considered are the vertical tail with arbitrary sweepback and taper ratio at Mach numbers for which both the leading edge and trailing edge of the tail are supersonic and the triangular vertical tail with a subsonic leading edge and a supersonic trailing edge. Expressions for potentials, pressures, and stability derivatives are tabulated.

Margolis, Kenneth↗

An Analysis of Pressure Studies and Experimental and Theoretical Downwash and Sidewash Behind Five Pointed-Tip Wings at Supersonic Speeds

Flow-angle and pressure surveys behind five, thin, pointed-tip wings of varying plan form have been made at Mach numbers 1.62 and 2.41. Schlieren studies at a Mach number 1.93 for the same five plan-form wings were made to illustrate the behavior of the vortex sheet. The surveys were conducted at 1.5, 3, and 4 root chords behind three triangular wings of 50 degree, 63 degree, and 72 degree leading-edge sweep angle, and behind the 50 degree triangular wing reversed. The flow behind a pointed-tip wing having a sweptback leading edge and a sweptforward trailing edge (both 50 degrees) was also surveyed. Experiment and one of the theoretical methods are compared for the reversed triangular wing and the pointed-tip wing with the 50 degree sweptback leading edge and sweptforward trailing edge.

Boatright, William B↗

Experimental investigation of the forces and moments due to sideslip of a series of triangular vertical and horizontal tail combinations at Mach numbers

An experimental investigation was made at Mach numbers of 1.62, 1.93, and 2.41 of a series of tail combinations consisting of triangular vertical tail attached symmetrically to a triangular horizontal tail to determine the lateral force, yawing moment, and rolling moment due to sideslip. The apex angles of both the vertical- and horizontal-tail surfaces were varied systematically in order to obtain results for an appreciable range of operating conditions. The results of the investigation indicated that, for tails having subsonic leading edges and supersonic trailing edges, the lateral-force derivative and the yawing-moment derivative were predicted satisfactorily by the method presented in NACA TN 3071 except when the leading edges approach a sonic condition. The theoretical rolling-moment derivative was in fair agreement with the experimental derivative. For the limited tests in which both the leading and trailing edges were supersonic, the prediction of the lateral-force derivative and the yawing-moment derivative obtained from NACA TN 2412 was in good agreement with the experimental derivatives, whereas the prediction of the rolling-moment derivative was fair.

Coletti, Donald E↗

Temperature in a J47-25 Turbojet-engine Combustor and Turbine Sections During Steady-state and Transient Operation in a Sea-level Test Stand

In order to determine the conditions of engine operation causing the most severe thermal stresses in the hot parts of a turbojet engine, a J47-25 engine was instrumented with thermocouples and operated to obtain engine material temperatures under steady-state and transient conditions. Temperatures measured during rated take-off conditions of nozzle guide vanes downstream of a single combustor differed on the order of 400 degrees F depending on the relation of the blades position to the highest temperature zone of the burner. Under the same operation conditions, measured midspan temperatures in a nozzle guide vane in the highest temperature zone of a combustor wake ranged from approximately 1670 degrees F at leading and trailing edges to 1340 degrees F at midchord on the convex side of the blade. The maximum measured nozzle-guide-vane temperature of 1920degrees at the trailing edge occurred during a rapid acceleration from idle to rated take-off speed following which the tail-pipe gas temperature exceeded maximum allowable temperature by 125 degrees F.

Morse, C R↗

A simple method for increasing the lift of airplane wings by means of flaps

Aerodynamic considerations led us, not long ago, to investigate a device which seemed to promise a contribution to the problem of reducing the landing speed of an airplane. We have subsequently learned that similar devices had already been proposed and investigated by others, but it seems advisable, nevertheless, to report our results. The problem is to create, in landing, a region of turbulence on the lower side of the wing near the trailing edge by some obstacle to the air flow. The devices tested by us consisted of flaps of varying chord and position, the chord s being equal to the distance of the pivot from the trailing edge.

Gruschwitz, Eugen↗

Combination Of Investment And Centrifugal Casting

Modifications, including incorporation of centrifugal casting, made in investment-casting process reducing scrap rate. Used to make first- and second-stage high-pressure-fuel-turbopump nozzles, containing vanes with thin trailing edges and other thin sections. Investment mold spun for short time while being filled, and stopped before solidification occurs. Centrifugal force drives molten metal into thin trailing edges, ensuring they are filled. With improved filling, preheat and pour temperatures reduced and solidification hastened so less hot tearing.

Creeger, Gordon A.↗

Composition and modal frequencies of hypervelocity particles less than 1 millimeter in diameter in low-Earth orbit

We have continued to systematically analyze the projectile residues associated with hypervelocity impact features on the surfaces of the 'Chemistry of Micrometeoroid Experiment' (CME) that was in low-Earth orbit (LEO) for 5.7 years aboard the Long Duration Exposure Facility (LDEF). Last year we reported on the systematic analysis, via SEM-EDX methods, of all craters greater than 20 microns in diameter on the collectors from LDEF's trailing edge and approximately 200 craters greater than 75 microns in diameter from the aluminum 1100 substrates from the forward-facing surfaces. This latter group represents less than 20 percent of all craters on the A11 collectors, because the particle flux is substantially higher for the forward-facing orientations relative to the trailing-edge surfaces. To date, we have analyzed some 600 craters on the A11 aluminum collectors, yet this report summarizes only 400 features, because not all of the results have been completely reduced and entered into our database.

Bernhard, R. P.↗

High Reynolds Number Configuration Development of a High-Lift Airfoil

An experimental program has been conducted to assess performance of a transport multielement airfoil at flight Reynolds numbers. The studies were performed at chord Reynolds numbers as high as 16 million in the NASA Langley Low Turbulence Pressure Tunnel. Sidewall boundary-layer control to enforce flow two dimensionality was provided via an endplate suction system. The basic airfoil was an 11.55 percent thick supercritical airfoil representative of the stall critical station of a new-generation transport aircraft wing. The multielement airfoil was configured as a three-element airfoil with slat and flap chord ratios of 14.48 percent and 30 percent respectively. Testing focused on the development of landing configurations with high maximum lift capability and the assessment of Reynolds and Mach number effects. Also assessed were high-lift performance effects due to devices such as drooped spoilers and trailing-edge wedges. The present experimental studies revealed significant effects on high-lift airfoil performance due to Reynolds and Mach number variations and favorable lift increments at approach angles of attack due to the use of drooped spoilers or trailing-edge wedges. However, no substantial improvements in maximum lift capability were identified. A recently developed high performance single-segment flap was also tested and results indicated considerable improvements in lift and drag performance over existing airfoils. Additionally, it was found that this new flap shape at its optimum rigging was less sensitive to Reynolds number variations than previous designs.

Walter O Valarezo↗

The impact of emissions from space transport systems on the state of the atmosphere

The exhaust products of space transport systems contain many substances, some of which can lead to ozone destruction. Significant changes in atmospheric constituents were calculated in a local area within a few kilometers of the exhaust trail of rockets (i.e., over 80% decreases in local ozone), although these effects are simulated to last only a few hours. Relatively small changes in atmospheric constituents are computed for regional areas within 1000 km of the exhaust trail (i.e. less than 10% decreases in column ozone), and even smaller changes are computed on a global scale (i.e., less than 0.03% decreases in total global ozone depletion).

Jackman, Charles H.↗

Base passive porosity for drag reduction

A device for controlling drag on a ground vehicle is presented. The device consists of a porous skin mounted on the trailing surface of the ground vehicle. The porous skin may be separated from the vehicle surface by a distance of at least two times the boundary layer formed on the surface. Alternately, the trailing surface of the ground vehicle may be porous. The device minimizes the strength of the separation in the base and wake regions of the ground vehicle, thus reducing drag.

Bauer, Steven X. S.↗

Active load control during rolling maneuvers

A rolling maneuver load alleviation (RMLA) system has been demonstrated on the active flexible wing (AFW) wind tunnel model in the Langley Transonic Dynamics Tunnel (TDT). The objective was to develop a systematic approach for designing active control laws to alleviate wing loads during rolling maneuvers. Two RMLA control laws were developed that utilized outboard control-surface pairs (leading and trailing edge) to counteract the loads and that used inboard trailing-edge control-surface pairs to maintain roll performance. Rolling maneuver load tests were performed in the TDT at several dynamic pressures that included two below and one 11 percent above open-loop flutter dynamic pressure. The RMLA system was operated simultaneously with an active flutter suppression system above open-loop flutter dynamic pressure. At all dynamic pressures for which baseline results were obtained, torsion-moment loads were reduced for both RMLA control laws. Results for bending-moment load reductions were mixed; however, design equations developed in this study provided conservative estimates of load reduction in all cases.

Woods-Vedeler, Jessica A.↗

Flame propagation under partially-premixed conditions

This study concentrates on developing a better understanding of triple flames. We relax the assumption of zero heat release, address the issue of stabilization, and, in order to investigate the role that heat release plays in flame propagation in partially premixed combustion, we return to a simple flow field and investigate the behavior of flames in a laminar environment. We solve the compressible Navier-Stokes equations in a two-dimensional domain. At the boundaries, we use an inflow boundary condition on the left and nearly-perfect reflective boundary conditions, required to avoid pressure drift, at the outflow and sides. After the flow and flame are initialized, the mixture fraction is varied at the inlet from its uniform stoichiometric value to a tanh profile varying from zero to one. As the mixture fraction gradient reaches the flame surface only the centerline is exposed to the stoichionetric mixture fraction and locally maintains the planar flame speed and reaction rate. Above this point the mixture is fuel rich, and below fuel lean. As a result, these regions of non-unity equivalence ratio burn less, the reaction rate drops, and the local flame speed is reduced. The excess fuel and oxidizer then combine behind the premixed flame along the stoichiometric surface and burn in a trailing diffusion flame. Thus the 'triple' flame refers to the fuel-rich premixed flame, the fuel-lean premixed flame, and the trailing diffusion flame. Due to heat release, the normal velocity across the flame is increased, whereas the tangential component remains unchanged. Far-field flame speed, local flame speed, and their differences are shown as a function of the local mixing thickness. It was also determined that the lateral position of the flame affects stabilization, and the distribution of the reaction rate along the premixed wings of triple flames affects flame propagation.

Ruetsch, Gregory R.↗

Control of flow separation in airfoil/wing design applications

Existing aerodynamic design methods have generally concentrated on the optimization of airfoil or wing shapes to produce a minimum drag while satisfying some basic constraints such as lift, pitching moment, or thickness. Since the minimization of drag almost always precludes the existence of separated flow, the evaluation and validation of these design methods for their robustness and accuracy when separated flow is present has not been aggressively pursued. However, two new applications for these design tools may be expected to include separated flow and the issues of aerodynamic design with this feature must be addressed. The first application of the aerodynamic design tools is the design of airfoils or wings to provide an optimal performance over a wide range of flight conditions (multipoint design). While the definition of 'optimal performance' in the multipoint setting is currently being hashed out, it is recognized that given a wide enough range of flight conditions, it will not be possible to ensure a minimum drag constraint at all conditions, and in fact some amount of separated flow (presumably small) may have to be allowed at the more demanding flight conditions. Thus a multipoint design method must be tolerant of the existence of separated flow and may include some controls upon its extent. The second application is in the design of wings with extended high speed buffet boundaries of their flight envelopes. Buffet occurs on a wing when regions of flow separation have grown to the extent that their time varying pressures induce possible destructive effects upon the wing structure or adversely effect either the aircraft controllability or the passenger comfort. A conservative approach to the expansion of the buffet flight boundary is to simply expand the flight envelope of nonseparated flow under the assumption that buffet will also thus be alleviated. However, having the ability to design a wing with separated flow and thus to control the location, extent, and severity of the separated flow regions may allow aircraft manufacturers to gain an advantage in the early design stages of an aircraft, when configuration changes are relatively inexpensive to make. Continuing the work begun last year, an airfoil design package has been modified to provide some control over the existence and extent of flow separation. This package consists of a 2-D Navier-Stokes flow solver which is coupled to the CDISC (constrained direct/iterative surface curvature) design method. The first modification is a prediction method for determining whether separation is likely based solely upon a given pressure distribution. If separation is predicted but is undesirable, the new routines will modify the pressure distribution to alleviate the problem. This new pressure distribution is then used in the design method to generate a new aerodynamic shape. Since separation may be acceptable in some cases, particularly if the separation does not extend to the trailing edge, another added logic estimates the extent of separation based upon a correlation with calculated separated flow cases. If the flow behind a shock induced separation is not predicted to reattach before the trailing edge, the logic weakens the shock strength and otherwise alters the pressure distribution in order to promote reattachment. This later addition is as yet unreliable due to secondary separation effects, but additional work is being pursued to improve the method.

Gally, Thomas A.↗

Aeroacoustic computation of gust-blade interaction

To better understand and address the challenges faced in computing the acoustics of flow fields, test problems must be considered. In the present study, the sound radiated by the interaction of a flat plate with an oncoming gust containing a two component, mean velocity is computed. The gust has a uniform mean flow in x with Mach number M(infinity) equal to 0.5. The gust's mean velocity in y is of smaller amplitude and is given by: v = 0.1 sin(pi/8(x/M(sub infinity) - t)). This problem has been posed for an upcoming ICASE/LaRC workshop on benchmark problems in computational aeroacoustics. A plate with a length of 30 units in x is used. The plate is assumed to be infinitesimally thin and is centered at the origin. All variables are made dimensionless using the scales specified. Acoustic quantities are obtained by numerically integrating the linearized Euler equations. Integration is performed on the computational domain -100.0 less than or equal to x less than or equal to 100.0, -100.0 less than or equal to y less than or equal to 100.0, using unit length grid spacing in x and in y. An integration scheme is sought which will provide accurate solution to the small quantities of interest at a minimal computational expense. Results indicate that with the given discretization a scheme of minimal fourth order accuracy might be adequate to approximate the waves within the given flow. Thus, a variation of the MacCormack scheme with fourth order accuracy in space and second order accuracy in time was chosen. A scheme with sixth order accuracy in space has also been implemented and results compared with those of the fourth order accurate scheme. To ensure no mass flux, zero normal velocity is assigned at the plate. This condition will induce a discontinuity in the pressure across the plate location. Values for the perturbation pressure p' along the surface of the plate are obtained using a one-sided, third order Taylor expansion, such that p'(sub y) = O. In accordance with the Kutta condition, perturbation pressure at the trailing edge is assigned to zero. In the far field, radiation boundary conditions have been implemented. The effectiveness of the far field conditions are validated by computing in a larger computational domain and comparing the results. Early in time, sound waves begin to radiate from the plate. A Doppler effect is observed. After the initial transients disappear, the strongest waves leave the trailing edge at an approximate 45 degree angle. The intensity pattern of pressure fluctuations shows five lobes (of increasing magnitude with increasing downstream direction) emerging from the plate. Undesirable short wave contaminants are observed in the computed pressure distribution along the plate surface. For a more accurate solution at small scales, a more refined discretization will be required.

Martin, James E.↗

Fission foil measurements of neutron and proton fluences in the A0015 experiment

Results are given from sets of fission foil detectors (FFD's) (Ta-181, Bi-209, Th-232, U-238) which were included in the A0015 experiment to measure combined proton/neutron fluences. Use has been made of recent FFD high energy proton calibrations for improved accuracy of response. Comparisons of track density measurements have been made with the predictions of environmental modeling based on simple 1-D (slab) geometry. At 1 g/cm(exp 2) (trailing edge) the calculations were approximately 25 percent lower than measurements; at 13 g/cm(exp 2) (Earthside) calculations were more than a factor of 2 lower. A future 3-D modeling of the experiment is needed for a more meaningful comparison. Approximate mission proton doses and neutron dose equivalents were found. At Earthside (13 g/cm(exp 2) the dose was 171 rad and dose equivalent was 82 rem. At the trailing edge (1 g/cm(exp 2) dose was 315 rad and dose equivalent was 33 rem. The proton doses are less than expected from TLD doses by 16 percent and 37 percent, respectively. These differences can be explained by uncertainties in the proton and neutron spectra and in the method used to separate proton and neutron contributions to the measurements.

Frank, A. L.↗

Secondary ion mass spectrometry (SIMS) analysis of hypervelocity microparticle impact sites on LDEF surfaces

Two dimensional elemental ion maps have been recorded for hundreds of microparticle impact sites and contamination features on LDEF surfaces. Since the majority of the analyzed surfaces were metal-oxide-silicon (MOS) impact detectors from the Interplanetary Dust Experiment, a series of 'standard' and 'blank' analyses of these surfaces are included. Hypervelocity impacts of forsterite olivine microparticles on activated flight sensors served as standards while stylus and pulsed laser simulated 'impacts' served as analytical blanks. Results showed that despite serious contamination issues, impactor residues can be identified in greater than 1/3 of the impact sites. While aluminum oxide particles could not be detected on aluminum surfaces, they were detected on germanium surfaces from row 12. Remnants of manmade debris impactors consisting of paint chips and bits of metal were identified on surfaces from LDEF Rows 3 (west or trailing side), 6 (south), 9 (ram or leading side), 12 (north) and the space end. Higher than expected ratios of manmade microparticle impacts to total microparticle impacts were found on the space end and the trailing side. These results were consistent with time-tagged and time-segregated microparticle impact data from the IDE and other LDEF experiments. A myriad of contamination interferences were identified and their effects on impactor debris identification mitigated during the course of this study. These interferences include pre-, post and inflight deposited surface contaminants as well as indigenous heterogeneous material contaminants. Non-flight contaminations traced to human origins, including spittle and skin oils, contributed significant levels of alkali-rich carbonaceous interferences. A ubiquitous layer of in-flight deposited silicaceous contamination varied in thickness with location on LDEF, even on a micro scale. In-flight deposited (low velocity) contaminants include urine droplets and bits of metal film from eroded thermal blankets.

Simon, C. G.↗