Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PROCESS HEAT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Microstructure and Mechanical Properties of Three-Layer TIG-Welded 2219 Aluminum Alloys with Dissimilar Heat Treatments

2219-C10S and 2219-CYS aluminum alloys are 2219 aluminum alloys with different heat treatment processes, and they have been widely used in the aerospace industry. In the present study, 2219-C10S and 2219-CYS aluminum alloys were butt-welded by three-layer tungsten inert gas arc welding (with the welding center of the third layer shifted toward the CYS side), and the microstructure characteristics and mechanical properties of the welded joint were investigated. The lamellar θ′ phases, the bulk or rod θ phases, and the coarse rod-shaped or pancake-shaped Al-Cu-Fe-Mn phases coexisted in the two aluminum alloys. The Cu content of the α-Al matrix and the distribution of eutectic structures of different welding layers in the weld zone (WZ) were varied, implying that the segregation degrees of the Cu element were different due to the different welding thermal cycles in different welding layers. The microhardness values of the CYS side were much higher than those of the C10S side in each region on both sides of the joint. The tensile test deformation was concentrated mainly in the regions of WZ and the over aged zone (OAZ), where the microhardness values were relatively low. The main deformation concentrated region was transferred from the CYS side to the C10S side with the increase in the tensile load during the tensile test. The fracture behavior of the tensile test showed that the macroscopic crack initiated near the front weld toe had gone through the crack blunt region, the shear fracture region of the partially melted zone (PMZ), and the shear fracture region of OAZ. Meanwhile, the fracture characteristics gradually evolved from brittle to ductile. The concentrated stress and the dense eutectic structure in the region near the front weld toe of the C10S side contributed to the fracture of the joint. The shift of the welding center of the third layer to the CYS side resulted in two effects: (i) the microhardness values from the middle layer to the top layer in the PMZ of the CYS side were the most significantly increased and (ii) the distance between the front weld toe and the fusion line of the CYS side was significantly larger.

36 MATERIALS SCIENCE↗

Renewable Thermal Energy Systems Designed for Industrial Process Solutions in Multiple Industries

The need for renewable heat in industry is vital for the next decade and beyond. Industrial decarbonization is a key area that must be accelerated, to foster the removal of fossil fuels from the provision of heat, especially at low temperatures. This paper looks at the development and results of case studies for understanding the economics and potential for renewable thermal energy systems (RTES), particularly in hybrid configurations to provide industrial process heat (IPH). For the case studies, these include non-concentrating e.g., heat pumps, and concentrating collectors e.g., parabolic trough collectors and direct steam generation (DSG)-linear Fresnel collectors (LFCs). The results show that a levelized cost of heat (LCOH) of $6-$8 per million British Thermal Units (MMBTU) is possible, depending on the direct normal irradiance (DNI) and the system sizing e.g., to increase the solar fractions. In Arizona for example, with a DNI of 7.36 kWh/m2/day, the base case for the DSG-LFC system with 6hrs of thermal energy storage could potentially meet a 1 MWth load 80% of the year.

concentrated solar thermal↗

Heating and cooling in adiabatic mixing process

We study the effect of interaction on the temperature change in the process of adiabatic mixing of two components of Fermi gases using the real-space Bogoliubov-de Gennes method. We find that in the process of adiabatic mixing, the competition between the adiabatic expansion and the attractive interaction makes it possible to cool or heat the system depending on the strength of the interaction and the initial temperature of the system. The changes of the temperature in a bulk system and in a trapped system are investigated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Process-Microstructure-Property Relationships in Low Heat Input Wire-Arc Additive Manufacturing (WAAM) of Ni-Based Superalloy Haynes 282

Conference presentation on WAAM process optimization on Ni-based superalloy Haynes® 282®. This alloy is targeted for advanced power generation systems for its superior high temperature mechanical properties. Wire-arc additive manufacturing (WAAM) offers attractive cost and materials savings with high deposition rates. Based on initial build process optimization, WAAM blocks were made, and screened for defects using high-throughput CT scanning. The microstructural evolution in arc energy range of 250-700 J/mm was characterized in the as-built and aged conditions, using electron microscopy. Results showed self-consistent microstructure across conditions, with grain size dependence on arc energy, MC and M6C carbides in as-built, and blocky grain boundary M23C6 in as-heat-treated condition. Further reductions in as-built porosity were explored through 20+ combinations of H2 and CO2 additions to shielding gas. Initial results show improved wetting behavior, and bead overlap with up to 1% H2 and up to 0.25% CO2. Combination of experimentally determined datasets provided comprehensive understanding of process-structure-property relationships in WAAM Haynes 282.

Haynes 282↗

Extremely Thin Perfect Absorber by Generalized Multipole Bianisotropic Effect

Symmetry breaking plays a crucial role in understanding the fundamental physics underlying numerous physical phenomena, including the electromagnetic response in resonators, giving rise to intriguing effects such as directional light scattering, supercavity lasing, and topologically protected states. Here, this work demonstrates that adding a small fraction of lossy metal (as low as 1 × 10 −6 in volume) to a lossless dielectric resonator breaks inversion symmetry (IS), thereby lifting its degeneracy, leading to a strong bianisotropic response. In the case of the metasurface composed of such resonators, this effect leads to unidirectional perfect absorption while maintaining nearly perfect reflection from the opposite direction. It has developed more general Onsager‐Casimir relations for the polarizabilities of particle arrays, taking into account the contributions of quadrupoles, which shows that bianisotropy is not solely due to dipoles, but also involves high‐order multipoles. The experimental validation demonstrates an extremely thin terahertz‐perfect absorber with a wavelength‐to‐thickness ratio of up to 25,000, where the material thickness is only 2% of the theoretical minimum thickness dictated by the fundamental limit. The findings can pave a new route to design devices for applications involving optical‐to‐heat conversion processes.

36 MATERIALS SCIENCE↗

Enhanced Photoreversible Color Switching of Redox Dyes Catalyzed by Barium-Doped TiO 2 Nanocrystals

We developed colloidal barium-doped TiO 2 nanocrystals that enable the highly reversible light-responsive color switching of redox dyes with excellent cycling performance and high switching rates. Oxygen vacancies resulting from the Ba doping serve as effective sacrificial electron donors (SEDs) to scavenge the holes photogenerated in TiO 2 nanocrystals under UV irradiation and subsequently promote the reduction of methylene blue to its colorless leuco form. Effective color switching can therefore be realized without relying on external SEDs, thus greatly increasing the number of switching cycles. Moreover, Ba doping can also accelerate the recoloration under visible-light irradiation by shifting the absorption edge of TiO 2 nanocrystals to a shorter wavelength. Such a system can be further casted into a solid film to produce a rewritable paper on which letters and patters can be repeatedly printed using UV light and then erased by heating; this process can be repeated for many cycles and does not require additional inks.

36 MATERIALS SCIENCE↗

Microscale drivers and mechanisms of fracture in post-processed additively manufactured Ti–6Al– 4 V

Herein, we focus on understanding the microstructure-fracture correlations in a Ti–6Al– 4 V alloy additively manufactured via electron beam melting (EBM) and subjected to various post-process heat-treatments. Specifically, the as fabricated material is subjected to a sub-transus heat-treatment followed by air-cooling and a super-transus heat-treatment followed by either air- or furnace-cooling. Next, a series of in-situ single edge notch tension (SENT) tests are carried out under a high-resolution digital optical microscope. The panoramic high-resolution images captured during the in-situ tests are then used to characterize the planar deformation on the specimen surface using microstructure-based digital image correlation (DIC). Additionally, the results of the in-situ SENT tests together with DIC and post-mortem fractographic analyses provided us with a better understanding of the microstructure-fracture correlations in these materials. Our results show that the fracture mechanism of the as fabricated and sub-transus heat-treated materials is essentially the same, while the changes in the microstructure following the super-transus heat-treatments significantly affects the fracture mechanism. In this case, several microcracks of hundreds of microns in length first nucleate away from the deformed notch following extreme plastic deformation at discrete locations. Furthermore, the location of these microcracks in the super-transus heat-treated materials is extremely sensitive to the details of the underlying microstructure.

36 MATERIALS SCIENCE↗

Entropy Dynamics in the System of Interacting Qubits

Here, the classical second law of thermodynamics demands that an isolated system evolves with a nondiminishing entropy. This holds as well in quantum mechanics if the evolution of the energy-isolated system can be described by a unital quantum channel. At the same time, the entropy of a system evolving via a nonunital channel can, in principle, decrease. Here, we analyze the behavior of entropy in the context of the H-theorem. As exemplary phenomena, we discuss the action of a Maxwell demon (MD) operating a qubit and the processes of heating and cooling in a two-qubit system. Further we discuss how small initial correlations between a quantum system and a reservoir affect the entropy increase during the quantum-system evolution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Tribological Performance of Austempered and Tempered Ductile Iron

Austempered ductile iron with its unique ausferritic structure is produced by an isothermal heat treatment process. Austempered ductile iron is a potential material to substitute for traditional steel castings and forgings in current industry due to its excellent mechanical properties. The tempering process is frequently used to enhance the ductility and toughness of a material and reduce residual stress. In this research, the phase transformation of austempered ductile iron was studied by applying various tempering temperatures with constant holding duration. It was found that the ausferritic structure was decomposed into dispersive cementite particles after receiving a tempering temperature of 538 °C or higher. The specific amount of retained austenite was analyzed by X-ray diffraction. The wear resistance of tempered austempered ductile iron was investigated by using a ball-on-disk sliding test configuration. The results were compared with conventional quenched and tempered ductile iron under equivalent hardness. Both austempered ductile iron and tempered austempered ductile iron samples had better wear resistance than quenched and tempered ductile iron. The results presented in this research can be utilized as a reference in the tempering treatment of austempered ductile iron material for future applications.

36 MATERIALS SCIENCE↗

A Study on Structural, Corrosion, and Sensitization Behavior of Ultrafine and Coarse Grain 316 Stainless Steel Processed by Multiaxial Forging and Heat Treatment

Cubic specimens from AISI 316 stainless steel were multiaxially forged to 15 passes and annealed at 1200 °C for 1, 2, and 3 h and finally sensitized at 700 °C for 24 h. Examination of samples indicated that the hardness of the annealed samples was reduced from 153 to 110, 81, and 74 HV for as-received sample and under 1, 2, and 3 h of annealing, and increased from 245 to 288 HV for samples forged at 3 and 7 passes. However, no significant changes were observed in a large number of passes and at about 300 HV. Degree of sensitization of samples was increased to approximately 27.3% at 3-h annealing but reduced to 1.23% by 15 passes of MF. The potentiodynamic polarization test shows that the breakdown potentials decreased with annealing time from 0.6 to − 102 (mV/SCE) for as-received and 3-h annealed specimen. These potentials increased to approximately − 16.5 mV with the increase in MF passes to 15. These observations indicated that the chromium carbide deposition affects Cr-depleted zone, which can subsequently affect the degree of sensitization and pitting corrosion resistance of AISI 316 austenitic stainless steel.

36 MATERIALS SCIENCE↗

Hardness of H13 Tool Steel After Non-isothermal Tempering

A direct method to calculate the tempering response of a tool steel (H13) that exhibits secondary hardening is presented. Based on the traditional method of presenting tempering response in terms of isothermal tempering, we show that the tempering response for a steel undergoing a non-isothermal tempering schedule can be predicted. Experiments comprised (1) isothermal tempering, (2) non-isothermal tempering pertaining to a relatively slow heating to process-temperature and (3) fast-heating cycles that are relevant to tempering by induction heating. After establishing the tempering response of the steel under simple isothermal conditions, the tempering response can be applied to non-isothermal tempering by using a numerical method to calculate the tempering parameter. Calculated results are verified by the experiments.

36 MATERIALS SCIENCE↗

Multiscale Modeling of Microstructural Evolution in Fused-Coating Additive Manufacturing

A quantitative phase field model with adaptive-computational-domain-expansion (ACDE) method was developed to simulate the microstructural evolution in fused-coating additive manufacturing process. A heat transfer and fluid flow model was established to investigate the solidification behavior of the molten pool in a single deposited layer. The solidification parameters such as temperature gradient and solidification rate were calculated from the macroscopic model and then fed into the phase field model to get the microstructure at different positions within a single deposited layer. Columnar dendrites were formed at the bottom of the deposited layer, and equiaxed dendrites appeared in the upper part of the layer. The ACDE method is used to improve the simulation efficiency. The metallographic experiments and energy-dispersive spectrometer analysis for composition were conducted on the fused-coating specimen, and the results were in good accordance with the simulations.

36 MATERIALS SCIENCE↗

Investigation into the Wear and Dent Resistance of Ni/Ti Nanolaminates and Superelastic NiTi Coating

Metallic wear-resistant coatings, such as chromium based, are desired to prevent premature failure of working parts and are widely used in the oil and gas and aerospace industries. These coatings are extremely hard; however, researchers have found that an optimal coating will also be resilient. Bulk NiTi possesses a superelasticity effect that can provide wear resistance to parts that will experience impact, wear, and erosion daily. Yet, NiTi as a surface coating has not been fully exploited in industrial applications. Bulk NiTi production presents significant challenges, such as poor formability and machinability. This study attempts to fabricate NiTi through a heat treatment process of sputter-deposited alternating nanosized Ni and Ti layers. After annealing, the nanolaminate coatings contained the austenitic NiTi phase. The elastic modulus to hardness ratio and wear resistance showed that the nanolaminate annealed at 650 °C is comparable to the sputtered superelastic NiTi coating. The annealed nanolaminate coating is found to exhibit higher hardness than the monolayered NiTi, as well as, comparable elastic modulus to hardness values and dent resistance. The findings in this study reveal the superiority of 650 °C annealed nanolaminate NiTi coating over the monolayer NiTi.

36 MATERIALS SCIENCE↗

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗

Lattice distortion in a strong and ductile refractory high-entropy alloy

Here, the maximization of the mixing entropy with the optimal range of enthalpy in high-entropy alloys (HEAs) can promote the formation of a stable single solid-solution phase with the absence of competing intermetallic compounds. The resultant effects, such as lattice distortion, can contribute to excellent mechanical properties, which has motivated numerous efforts to develop and design single-phase HEAs. However, challenges still remain, particularly on quantifying the lattice distortion and relating it to materials properties. In this study, we have developed a NbTaTiV refractory HEA with a single body-centered-cubic (BCC) structure using an integrated experimental and theoretical approach. The theoretical efforts include thermodynamic modeling, i.e., CALculation of PHAse Diagram (CALPHAD). The microstructural evolutions have been investigated by systematic heat-treatment processes. The typical dendrite microstructure was observed, which is caused by the elemental segregation during the solidification in the as-cast condition. The structural inhomogeneity and chemical segregation were completely eliminated by the proper homogenization treatment at 1200 °C for 3 days. The homogeneous elemental distribution was quantitatively verified by the Atom Probe Tomography (APT) technique. Importantly, results indicate that this HEA exhibits the high yield strength and ductility at both room and high temperatures (up to 900 °C). Furthermore, the effects of the high mixing entropy on the mechanical properties are discussed and quantified in terms of lattice distortions and interatomic interactions of the NbTaTiV HEA via first-principles calculations. It is found that the local severe lattice distortions are induced, due to the atomic interactions and atomic-size mismatch in the homogenization-treated NbTaTiV refractory HEA.

36 MATERIALS SCIENCE↗

Assessment of metadynamic recrystallization in single copper particle impacts by focused ion beam tomography

We study single Cu-on-Cu impacts relevant to cold spray deposition and quantitatively analyze the metadynamic recrystallization (mDRX) that takes place after the impact by virtue of lingering impact adiabatic heat. Unlike prior studies, the current full 3D tomographic analysis of the mDRX volume shows that mDRX is extremely common in such impacts, although it is often missed when examining 2D sections. We also report an unexpected trend: there is a “sour spot” for mDRX at velocities about 20–40 % above the velocity for particle adhesion. This non-monotonic trend is contrary to the expectations based on increasing adiabatic heating with velocity. With a schematic model, we show that the trend can be explained on the basis of heat transfer: cooling of the heat-affected region is limited by transport through the bonded regions at the particle-substrate interface. Thus, bonding has a prominent role in the heat dissipation process and the best bonded particles most rapidly bulk quench, avoiding mDRX. Here, the developed semi-empirical model aligns with the experimental findings and may help inform microstructural evolution during cold spray and post-spray processing.

FIB-SEM tomography↗

A Potts Model parameter study of particle size, Monte Carlo temperature, and “Particle-Assisted Abnormal Grain Growth”

A Potts Model was proposed to account for temperature and particle heterogeneity-dependent Zener Pinning. This was accomplished by relating the random fluctuations of grain boundary position allowed by the Potts Model switching probability at finite simulation temperature to experimentally observed grain growth stagnation behavior. We assume that these fluctuations arise from random fluctuations in the thermodynamic and kinetic properties of the grain boundaries and/or interfaces as they change with temperature. As an application of this model, the grain growth kinetics of U-10 wt. % Mo nuclear fuels were simulated with the input of microstructural images during different heat treatment processes. Simulated average grain growth behavior is in good agreement with experiments.

Frazier, William E.↗