Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA PRODUCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Data reduction and analysis of HELIOS plasma wave data

Reduction of data acquired from the HELIOS Solar Wind Plasma Wave Experiments on HELIOS 1 and 2 was continued. Production of 24 hour survey plots of the HELIOS 1 plasma wave data were continued and microfilm copies were submitted to the National Space Science Data Center. Much of the effort involved the shock memory from both HELIOS 1 and 2. This data had to be deconvoluted and time ordered before it could be displayed and plotted in an organized form. The UNIVAX 418-III computer was replaced by a DEC VAX 11/780 computer. In order to continue the reduction and analysis of the data set, all data reduction and analysis computer programs had to be rewritten.

Anderson, Roger R.↗

Spacelab 2 electron beam wave stimulation - Studies of important parameters

Experimental results from Spacelab 2 experiments on the production of waves in ionospheric plasma by the injection of pulsed electron beams are reported. The wave environments which exist in the orbiter payload bay and at several hundred meters away are compared both during ambient conditions and during electron beam injections. The duty cycle of the beam is found to be one of the most important parameters affecting the amplitude and the harmonic structure of the waves. Maximum amplitudes are produced by 50 percent duty cycles and amplitudes are proportional to instantaneous, rather than average, beam current. The dependence of the harmonic structure on pulsing frequency shows good agreement with theory for whistler mode waves produced by the Cerenkov resonance.

Reeves, G. D.↗

Plasma separation

This process employs a thermal plasma for the separation and production of oxygen and metals. It is a continuous process that requires no consumables and relies entirely on space resources. The almost complete absence of waste renders it relatively clean. It can be turned on or off without any undesirable side effects or residues. The prime disadvantage is its high power consumption.

Steurer, Wolfgang↗

Gamma-ray line afterglow from burst environments

We consider photoerosion and direct pair production in a medium surrounding a gamma-ray burst. The resulting secondary gamma-rays may provide diagnostic tools of these environments and, in turn, of the nature of the bursters themselves. In some instances short-lived nuclides are formed; the beta-delayed gamma-rays produced from their decays provide the signatures of the photoerosion. In addition, annihilation radiation produced from positrons resulting from direct pair production is related to the plasma conditions in the medium. We investigate the plausibility of detecting the various radiations. Under extremely favorable conditions, the photoerosion afterglow might be detectable with the present generation of detectors. However, the positron annihilation line should be detectable under a fairly wide range in the conditions of the medium.

Fencl, H. S.↗

Ionospheric Instabilities and Shock Capturing Algorithms

We describe the basic physics of the gradient-drift instability and the collisional Rayleigh-Taylor instability, the two plasma instabilities which dominate the production of small-scale structure in the earth's ionosphere. We then focus our attention on the nonlinear evolution of these instabilities for two particular cases: 1) the recursive bifurcation and "freezing" of artificial ion clouds released in the ionosphere; and 2) equatorial spread F. Finally, we discuss the numerical challenges faced in attempting to numerically simulate these instabilities, and the role played by shock-capturing algorithms therein.

Zalesak, Steven T.↗

Evaluation of the Combined Effects of Gamma Radiation and High Dietary Iron on Peripheral Leukocyte Distribution and Function

NASA is concerned with the health risks to astronauts, particularly those risks related to radiation exposure. Both radiation and increased iron stores can independently increase oxidative damage, resulting in protein, lipid and DNA oxidation. Oxidative stress increases the risk of many health problems including cancer, cataracts, and heart disease. This study, a subset of a larger interdisciplinary investigation of the combined effect of iron overload on sensitivity to radiation injury, monitored immune parameters in the peripheral blood of rats subjected to gamma radiation, high dietary iron or both. Specific immune measures consisted of (A) peripheral leukocyte distribution; (B) plasma cytokine levels; (C) cytokine production profiles following whole blood stimulation of either T cells or monocytes.

Crucian, Brian E.↗

The role of focusing geometry in MeV x-ray production from petawatt laser–solid interaction

Relativistic laser–plasma interactions provide a compact and flexible route to generating bright, ultrashort pulses of MeV x rays, with applications in high-energy density science, nuclear physics, and radiography. Despite extensive study of intensity scaling in laser-driven electron acceleration, the role of focusing geometry and focal-volume effects in MeV radiation production remains insufficiently understood. Here, we present experimental and kinetic simulation results from the Texas Petawatt Laser (120 J, 140 fs) in which the focusing geometry (f/3 or f/1.5) is varied, while the laser energy and pulse duration are fixed. Experimentally, the f/3 geometry produces approximately three times more MeV radiation than the f/1.5 geometry, despite its twofold lower nominal vacuum intensity. This result is based on the time-integrated radiation per unit solid angle, as measured along the diagnostic line of sight. Three-dimensional particle-in-cell simulations reproduce this trend when a modest (10s of μm) effective focal plane shift is introduced, demonstrating that relativistic laser–plasma coupling is highly sensitive to focal geometry in the presence of a preplasma. This behavior is consistent with differences in interaction length and effective intensity at the critical surface between the two configurations. The sensitivity of the tightly focused f/1.5 configuration ($z_R ≈$⁠ 5 μ m) reflects the combined influence of thermal lensing and an extended preplasma, while the f/3 geometry (⁠$z_R ≈$ 80 μ m) remains comparatively robust. These results demonstrate a breakdown of conventional intensity scaling and identify focusing geometry as a critical control parameter for MeV electron and x-ray generation at petawatt powers. Implications for laser–plasma-based radiographic facilities are also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Particle-in-cell with Monte Carlo collision modeling of the electron and negative hydrogen ion transport across a localized transverse magnetic field

The control of the electron temperature and charged particle transport in negative hydrogen ion sources has a crucial role for the performance of the system. It is usually achieved by the use of a magnetic filter--localized transverse magnetic field, which reduces the electron temperature and enhances the negative ion yield. There are several works in literature on modeling of the magnetic filter effects based on fluid and kinetic modeling, which, however, suggest rather different mechanisms responsible for the electron cooling and particle transport through the filter. Here a kinetic modeling of the problem based on the particle-in-cell with Monte Carlo collisions method is presented. The charged particle transport across a magnetic filter is studied in hydrogen plasmas with and without including volume production of negative ions, in a one-dimensional Cartesian geometry. The simulation shows a classical (collisional) electron diffusion across the magnetic filter with reduction in the electron temperature but no selective effect in electron energy is observed (Coulomb collisions are not considered). When a bias voltage is applied, the plasma is split into an upstream electropositive and a downstream electronegative regions. Different configurations with respect to bias voltage and magnetic field strength are examined and discussed. Although the bias voltage allows negative ion extraction, the results show that volume production of negative ions in the downstream region is not really enhanced by the magnetic filter.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Technical Feasibility Assessment of LED Roadway Lighting on the Golden Gate Bridge

Subsequent to preliminary investigations by the Golden Gate Bridge Highway & Transportation District (GGB), in coordination with Pacific Gas & Electric (PG&E), the GATEWAY Demonstration program was asked to evaluate the technical feasibility of replacing existing roadway lighting on the bridge with products utilizing LED technology. GGB and PG&E also indicated interest in induction (i.e., electrodeless fluorescent) technology, since both light source types feature rated lifetimes significantly exceeding those of the existing high-pressure sodium (HPS) and low-pressure sodium (LPS) products. The goal of the study was to identify any solutions which would reduce energy use and maintenance without compromising the quantity or quality of existing illumination. Products used for roadway lighting on the historic bridge must be installed within the existing amber-lensed shoebox-style luminaire housings. It was determined that induction technology does not appear to represent a viable alternative for the roadway luminaires in this application; any energy savings would be attributable to a reduction in light levels. Although no suitable LED retrofit kits were identified for installation within existing luminaire housings, several complete LED luminaires were found to offer energy savings of 6-18%, suggesting custom LED retrofit kits could be developed to match or exceed the performance of the existing shoeboxes. Luminaires utilizing ceramic metal halide (CMH) were also evaluated, and some were found to offer 28% energy savings, but these products might actually increase maintenance due to the shorter rated lamp life. Plasma technology was evaluated, as well, but no suitable products were identified. Analysis provided in this report was completed in May 2012. Although LED technologies are expected to become increasingly viable over time, and product mock-ups may reveal near-term solutions, some options not currently considered by GGB may ultimately merit evaluation. For example, it would be preferable in terms of performance to simply replace existing luminaires (some of which may already be nearing end of life) with fully-integrated LED or CMH luminaires rather than replacing internal components. Among other benefits, this would allow reputable manufacturers to offer standard warranties for their products. Similarly, the amber lenses might be reformulated such that they do not render white light sources in a greenish cast, thereby allowing the use of off-the-shelf LED or CMH products. Last, it should be noted that the existing amber-lensed shoeboxes bear no daytime resemblance to the LPS luminaires originally used to light the roadway.

ceramic metal halide↗

Magnetohydrodynamic Stability of a Toroidal Plasma's Separatrix

Large tokamaks capable of fusion power production such as ITER, should avoid large edge localized modes (ELMs), thought to be triggered by an ideal magnetohydrodynamic instability due to current at the plasma's separatrix boundary. Unlike analytical work in a cylindrical approximation, numerical work finds the modes are stable. The plasma's separatrix might stabilize modes, but makes analytical and numerical work difficult. We generalize a cylindrical model to toroidal separatrix geometry, finding one parameter {delta}{sup '} determines stability. The conformal transformation method is generalized to allow nonzero derivatives of a function on a boundary, and calculation of the equilibrium vacuum field allows {delta}{sup '} to be found analytically. As a boundary more closely approximates a separatrix, we find the energy principle indicates instability, but the growth rate asymptotes to zero.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

2D imaging of absolute methyl concentrations in nanosecond pulsed plasma by photo-fragmentation laser-induced fluorescence

The methyl radical plays a central role in plasma-assisted hydrocarbon chemistry but is challenging to detect due to its high reactivity and strongly pre-dissociative electronically excited states. In this work, we report the development of a photo-fragmentation laser-induced fluorescence (PF-LIF) diagnostic for quantitative 2D imaging of methyl profiles in a plasma. This technique provides temporally and spatially resolved measurements of local methyl distributions, including in near-surface regions that are important for plasma-surface interactions such as plasma-assisted catalysis. The technique relies on photo-dissociation of methyl by the fifth harmonic of a Nd:YAG laser at 212.8 nm to produce CH fragments. These photofragments are then detected with LIF imaging by exciting a transition in the B-X(0, 0) band of CH with a second laser at 390 nm. Fluorescence from the overlapping A-X(0, 0), A-X(1, 1), and B-X(0, 1) bands of CH is detected near 430 nm with the A-state populated by collisional B-A electronic energy transfer. This non-resonant detection scheme enables interrogation close to a surface. The PF-LIF diagnostic is calibrated by producing a known amount of methyl through photo-dissociation of acetone vapor in a calibration gas mixture. We demonstrate PF-LIF imaging of methyl production in methane-containing nanosecond pulsed plasmas impinging on dielectric surfaces. Absolute calibration of the diagnostic is demonstrated in a diffuse, plane-to-plane discharge. Measured profiles show a relatively uniform distribution of up to 30 ppm of methyl. Relative methyl measurements in a filamentary plane-to-plane discharge and a plasma jet reveal highly localized intense production of methyl. The utility of the PF-LIF technique is further demonstrated by combining methyl measurements with formaldehyde LIF imaging to capture spatiotemporal correlations between methyl and formaldehyde, which is an important intermediate species in plasma-assisted oxidative coupling of methane.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cold crucible induction melter test for crystalline ceramic waste form fabrication: A feasibility assessment

The first scaled proof-of-principle cold crucible induction melter (CCIM) test to process a multiphase ceramic waste form from a simulated combined (Cs/Sr, lanthanide and transition metal fission products) commercial used nuclear fuel waste stream was recently conducted in the United States. X-ray diffraction, 2-D X-ray absorption near edge structure (XANES), electron microscopy, inductively coupled plasma-atomic emission spectroscopy (and inductively coupled plasma-mass spectroscopy for Cs), and product consistency tests were used to characterize the fabricated CCIM material. Characterization analyses confirmed that a crystalline ceramic with a desirable phase assemblage was produced from a melt using a CCIM. We identified primary hollandite, pyrochlore/zirconolite, and perovskite phases in addition to minor phases rich in Fe, Al, or Cs. The material produced in the CCIM was chemically homogeneous and displayed a uniform phase assemblage with acceptable aqueous chemical durability.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Perspectives on relativistic electron–positron pair plasma experiments of astrophysical relevance using high-power lasers

The study of relativistic electron–positron pair plasmas is both of fundamental physics interest and important to understand the processes that shape the magnetic field dynamics, particle acceleration, and radiation emission in high-energy astrophysical environments. Although it is highly desirable to study relativistic pair plasmas in the laboratory, their generation and control constitutes a critical challenge. Significant experimental and theoretical progress has been made over recent years to explore the use of intense lasers to produce dense relativistic pair plasma in the laboratory and study the basic collective plasma processes associated with these systems. Important challenges remain in terms of improving the number of pairs, system size, and control over the charge neutrality required to establish laboratory platforms that can expand our understanding of relativistic pair plasma and help validate underlying models in conditions relevant to high-energy astrophysical phenomena. Furthermore, we highlight recent progress in this field, discuss the main challenges, and the exciting prospects for studying relativistic pair plasmas and astrophysics relevant instabilities in the laboratory in the near future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fast ion relaxation in ITER mediated by Alfvén instabilities

Abstract We address the critical issue for future burning plasmas of whether high-energy fusion products or auxiliary heating-beam ions will be confined for a sufficiently long time to compensate for thermal plasma energy losses. This issue can be mitigated by one of the most deleterious collective phenomena—the instability of low, sub-cyclotron frequency Alfvén eigenmodes (AEs), such as toroidicity-induced AEs and reversed-shear AEs in the ITER steady-state scenario. Using a revised quasi-linear (QL) theory applied to energetic particle (EP) relaxation in the presence of AEs, we find that the AE instabilities can affect both neutral beam ions and alpha particles, although the resulting fast ion transport is expected to be modest if classical particle slowing down is assumed. On the other hand, the QL theory predicts that the AE amplitudes will be enhanced by the background microturbulence, although this topic remains outside our scope due to the significant numerical effort required to evaluate these effects. We report our results for EP relaxation dynamics obtained utilizing several tools: (i) a comprehensive linear stability study of the sub-cyclotron Alfvénic spectrum as computed by ideal magnetohydrodynamic NOVA simulations for the AE eigenproblem, (ii) drift kinetic NOVA-C calculations for wave–particle interaction and AE growth/damping rates, and (iii) predictive QL modeling coupled with the global transport code TRANSP to assess the EP relaxation on the equilibrium timescale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma-Assisted Chemical-Looping Combustion: Low-Temperature Methane and Ethylene Oxidation with Nickel Oxide

The chemical reaction network of low-temperature plasma-assisted oxidation of methane (CH 4 ) and ethylene (C 2 H 4 ) with nickel oxide (NiO) was investigated in a heated plasma reactor through time-dependent species measurements by electron-ionization molecular beam mass spectrometry (EI-MBMS). Methane (ethylene) oxidation by NiO was explored in temperature ranges from 300-700 °C (300-500 °C) and 300-800 °C (300-600°C) for the plasma and non-plasma conditions, respectively. Significant enhancement of methane oxidation was observed with plasma between 400 and 500 °C, where no oxidation was observed under non-plasma conditions. For the oxidation of methane at higher temperatures three different oxidation stages were observed: I) a period of complete oxidation, II) a period of incomplete CO oxidation, and III) a period of carbon buildup. For the C 2 H 4 experiments, and unlike the CH 4 experiments, the plasma resulted in a significant amount of new intermediate oxygenated species, such as CH 2 O, CH 3 OH, C 2 H 4 O, and C 2 H 6 O. Carbon deposits were observed under both methane and ethylene conditions and verified by X-ray photoelectron spectroscopy (XPS). ReaxFF simulations were performed for the oxidation of CH 4 and C 2 H 4 in a non-plasma environment. The simulated intermediates and products largely agree with the species measured in the experiments, though the predicted intermediate oxygenated species such as CH 2 O and C 2 H 6 O were not observed in experiments under non-plasma conditions. A reaction pathway analysis for CH 4 and C 2 H 4 reacting with NiO was created based on the observed species from the MBMS spectra, along with ReaxFF simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Formation of PtSi Schottky barrier MOSFETs using plasma etching

PtSi Schottky barrier (SB) MOSFETs were fabricated and their device performance was characterized. PtSi was selected instead of NiSi to form the p-type SB junction since such a configuration would be easy to fabricate through SF{sub 6} based plasma etching. The addition of He-O{sub 2} in SF{sub 6} decreases the etching rate of PtSi while the etching rate of Pt remains unchanged. The retardation in the etching rate of PtSi in He-O{sub 2}/SF{sub 6} is attributed to the formation of a metal oxide on the etched PtSi surface, as evidenced by the x-ray photoelectron spectroscopy results. Optical emission spectroscopy was conducted to establish the endpoint where the wavelength from the feed gas was traced instead of tracing the etching by-products since the by-products have little association with the plasma reaction. The I{sub DS}–V{sub DS} curves at various V{sub G}–V{sub TH} indicate that plasma etching resulted in the successful removal of the Pt on the sidewall region, with negligible damage to the S/D area.

42 ENGINEERING↗

Plasma enhanced atomic layer batch processing of aluminum doped titanium dioxide

Among many promising high-k dielectrics, TiO{sub 2} is an interesting candidate because of its relatively high k value of over 40 and its easy integration into existing semiconductor manufacturing schemes. The most critical issues of TiO{sub 2} are its low electrical stability and its high leakage current density. However, doping TiO{sub 2} with Al has shown to yield significant improvement of layer quality on Ru electrodes [S. K. Kim et al., Adv. Mater. 20, 1429 (2008)]. In this work we investigated if atomic layer deposition (ALD) of Al doped TiO{sub 2} is feasible in a batch system. Electrical characterizations were done using common electrode materials like TiN, TaN, or W. Additionally, the effect of plasma enhanced processing in this reactor was studied. For this investigation a production batch ALD furnace has been retrofitted with a plasma source which can be used for post deposition anneals with oxygen radicals as well as for directly plasma enhanced ALD. After evaluation of several Ti precursors a deposition process for AlTiO{sub x} with excellent film thickness and composition uniformity was developed. The effects of post deposition anneals, Al{sub 2}O{sub 3} interlayers between electrode and TiO{sub 2}, Al doping concentration, plasma enhanced deposition and electrode material type on leakage current density are shown. An optimized AlTiO{sub x} deposition process on TaN electrodes yields to leakage current density of 5 x 10{sup -7} A/cm{sup 2} at 2 V and k values of about 35. Thus, it could be demonstrated that a plasma enhanced batch ALD process for Al doped TiO{sub 2} is feasible with acceptable leakage current density on a standard electrode material.

36 MATERIALS SCIENCE↗

Technical Feasibility Assessment of LED Roadway Lighting on the Golden Gate Bridge

Subsequent to preliminary investigations by the Golden Gate Bridge Highway & Transportation District (GGB), in coordination with Pacific Gas & Electric (PG&E), the GATEWAY Demonstration program was asked to evaluate the technical feasibility of replacing existing roadway lighting on the bridge with products utilizing LED technology. GGB and PG&E also indicated interest in induction (i.e., electrodeless fluorescent) technology, since both light source types feature rated lifetimes significantly exceeding those of the existing high-pressure sodium (HPS) and low-pressure sodium (LPS) products. The goal of the study was to identify any solutions which would reduce energy use and maintenance without compromising the quantity or quality of existing illumination. Products used for roadway lighting on the historic bridge must be installed within the existing amber-lensed shoebox-style luminaire housings. It was determined that induction technology does not appear to represent a viable alternative for the roadway luminaires in this application; any energy savings would be attributable to a reduction in light levels. Although no suitable LED retrofit kits were identified for installation within existing luminaire housings, several complete LED luminaires were found to offer energy savings of 6-18%, suggesting custom LED retrofit kits could be developed to match or exceed the performance of the existing shoeboxes. Luminaires utilizing ceramic metal halide (CMH) were also evaluated, and some were found to offer 28% energy savings, but these products might actually increase maintenance due to the shorter rated lamp life. Plasma technology was evaluated, as well, but no suitable products were identified. Analysis provided in this report was completed in May 2012. Although LED technologies are expected to become increasingly viable over time, and product mock-ups may reveal near-term solutions, some options not currently considered by GGB may ultimately merit evaluation. For example, it would be preferable in terms of performance to simply replace existing luminaires (some of which may already be nearing end of life) with fully-integrated LED or CMH luminaires rather than replacing internal components. Among other benefits, this would allow reputable manufacturers to offer standard warranties for their products. Similarly, the amber lenses might be reformulated such that they do not render white light sources in a greenish cast, thereby allowing the use of off-the-shelf LED or CMH products. Last, it should be noted that the existing amber-lensed shoeboxes bear no daytime resemblance to the LPS luminaires originally used to light the roadway.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗