SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Monitor improves complex network reliability in computer data links and command transmission lines. System evaluates circuit performance against preselected criteria, identifies and stores data indicating out-of-tolerance conditions, conducts closed loop testing, and provides for operation under command of digital computer that determines restoration priorities.
An overall systems evaluation was made of five candidate navigation systems in support of earth orbit missions. The five systems were horizon sensor system, unkown landmark tracking system, ground transponder system, manned space flight network, and tracking and data relay satellite system. Two reference missions were chosen: a low earth orbit mission and a transfer trajectory mission from low earth orbit to geosynchronous orbit. The specific areas addressed in the evaluation were performance, multifunction utilization, system mechanization, and cost.
The tracking and data system support of the launch, near-earth, and deep space phases of the Pioneer 10 mission, which sent a Pioneer spacecraft into a flyby of Jupiter that would eventually allow the spacecraft to escape the solar system is discussed. The support through the spacecraft's second trajectory correction is reported. During this period, scientific instruments aboard the spacecraft registered information relative to interplanetary particles and fields, and radiometric data generated by the network continued to improve knowledge of the celestial mechanics of the solar system. In addition to network support activity detail, network performance and special support activities are covered.
The Tracking and Data System supported the deep space phases of the Pioneer 6, 7, 8, and 9 missions, with two spacecraft in an inward trajectory and two spacecraft in an outward trajectory from the earth in heliocentric orbits. Scientific instruments aboard each of the spacecraft continued to register information relative to interplanetary particles and fields, and radio metric data generated by the network continued to improve our knowledge of the celestial mechanics of the solar system. In addition to network support activity detail, network performance and special support activities are covered.
A study which may guide the operations of existing computer installations, as well as the design of future networks, is described. Performance data and evaluations are considered with reference to interarrival time, users' habits, waiting time for execution, time spent in a partition, figures of merit, and states of the system. The analysis of the variables proceeds from examination of typical data with appropriate statistical tests to conclusions about the possible state of nature.
In this annotated and indexed listing of works on teleconferencing, emphasis has been placed upon teleconferencing as real-time, two way audio communication with or without visual aids. However, works on the use of television in two-way or multiway nets, data transmission, regional communications networks and on telecommunications in general are also included.
The Tracking and Data System supported the deep space phases of the Pioneer 6, 7, 8, and 9 missions, with two spacecraft in an inward trajectory and two spacecraft in an outward trajectory from the earth in heliocentric orbits. During the period of this report, scientific instruments aboard each of the spacecraft continued to register information relative to interplanetary particles and fields, and radiometric data generated by the network continued to contribute to knowledge of the celestial mechanics of the solar system. In addition, to network support activity detail, network performance and special support activities are covered.
The feasibility of having a common information management network for space shuttle data, is studied. Identified are the information types required, sources and users of the information, and existing techniques for acquiring, storing and retrieving the data. The study concluded that a decentralized system is feasible, and described a recommended development plan for it.
The proceedings of a symposium on significant accomplishments in science and technology are presented. The symposium was held at the Goddard Space Flight Center in December 1973. The subjects discussed are as follows: (1) cometary physics, (2) X-ray and gamma ray astronomy, (3) solar and terrestrial physics, (4) spacecraft technology, (5) Earth Resources Technology Satellite, (6) earth and ocean physics, (6) communications and navigation, (7) mission operations and data systems, and (8) networks systems and operations.
A prototype data acquisition and dissemination network and its effectiveness in improving and/or solving hydrologic problems in southern Florida are evaluated. The network utilized LANDSAT MSS imagery and in situ monitoring by LANDSAT-DCS. Results show water level and rain fall measurements were collected and disseminated in less than two hours, a significant improvement over conventional methods which took up to two months. Improved network performance has also aided the development of water budgets and water distribution to the people, funa, and flora in the area. Imagery from LANDSAT was also found to enhance the utility of ground measurements.
The University of Illinois and the U.S. Department of Agriculture have collaborated to examine the feasibility of Landsat imagery analysis for USDA crop-acreage estimation purposes. The region chosen for the experiment was ten western counties of Illinois. Preliminary crop-acreage estimates derived from the ILLIAC IV-ARPA Network analysis of Landsat data are presented for these ten counties. Assuming the practicality of similar analyses covering the entire state, a procedure is discussed for evaluating statistically the information to be gained by estimating state crop-acreage totals from Landsat imagery classification results where SRS sample survey data are used as ground truth information for classification training as opposed to estimating state crop-acreage totals directly from SRS survey data alone.
Atmospheric acoustic probes located either at shore locations near the Chesapeake Bay or on large surface buoys could obtain profiles of wind velocity and turbulence and the temperature and humidity of the atmosphere. At or near the buoy locations, underwater probes located on the bottom could be used to profile current velocity, density, and turbulence and also to determine tide level, wave height, spectrum, and direction. The physical parameter profiles at these earth-surface stations could be used with surface observations by satellite. The most obvious use of data from such a network is to verify and calibrate models of energy exchange between the water of the Bay and the atmosphere.
The status of the Viking Deep Space Network Mark 3 '77 data subsystem implementation project and related testing at DSS 42/43 from 1 September through 31 October 1977 are reported. The Viking DSN discrepancy reporting system, Viking command support, tracking support, and periodic tests conducted with the Viking spacecraft are also discussed.
The onset of auroral breakup was studied by using a variety of instruments with time resolution of some tens of second. Rapid sequences of all-sky photographs, and fast meridian scans by photometers, show that breakup is usually preceded by moderate brightening, followed by fading of the auroral brightness lasting one or two minutes, before the actual breakup itself. This optical activity is closely correlated with the development of auroral radar echoes. Data from a magnetometer network provide some indication of a correlated response by the local auroral and ionospheric currents. Riometer recordings show a slow decrease in ionspheric radio wave absorption over a period of about ten minutes prior to breakup, with the largest decrease essentially to quiet-time values in the region of auroral fading and subsequent breakup.
A program of ALSEP-quasar very-long-baseline interferometry (VLBI) is being carried out. These observations employ primarily a 'four-antenna' technique whereby simultaneous observations with two antennas at each end of an intercontinental baseline are used to derive the differential interferometric phase between a compact extragalactic radio source (usually a quasar) and a number of ALSEP transmitters on the lunar surface. A continuous ALSEP-quasar differential phase history over a period of a few hours will lead to milliarcsecond angular accuracy in measuring the lunar position against the quasar reference frame if suitable calibration measurements are obtained. Development of this application of the four-antenna technique has been underway for more than a year and is producing high-quality data utilizing Deep Space Network stations. These high-accuracy observations are of value to tie the lunar ephemeris to a nearly inertial extragalactic reference frame, to test gravitational theories, and to measure the earth-moon tidal friction interaction.
Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM), a highly interactive software, has been implemented on minicomputers at the NASA Langley Research Center. CAD/CAM software integrates many formerly fragmented programs and procedures into one cohesive system; it also includes finite element modeling and analysis, and has been interfaced via a computer network to a relational data base management system and offline plotting devices on mainframe computers. The CAD/CAM software system requires interactive graphics terminals operating at a minimum of 4800 bits/sec transfer rate to a computer. The system is portable and introduces 'interactive graphics', which permits the creation and modification of models interactively. The CAD/CAM system has already produced designs for a large area space platform, a national transonic facility fan blade, and a laminar flow control wind tunnel model. Besides the design/drafting element analysis capability, CAD/CAM provides options to produce an automatic program tooling code to drive a numerically controlled (N/C) machine. Reductions in time for design, engineering, drawing, finite element modeling, and N/C machining will benefit productivity through reduced costs, fewer errors, and a wider range of configuration.
The need for detailed specifications is addressed. Candidates for standardization include hardware interfaces, communication protocols, and data exchange services. Atmosphere, Ocean, and Resource pilot programs, utilization of current techniques and technologies in the use and exchange of data and to facilitate access to data are discussed. Pilot objectives aim to: (1) demonstrate the use of advanced technologies, (2) provide a test bed environment for data handling technique evaluation, (3) evolve requirements and capabilities, and (4) document validated methodologies as standards and guidelines for data systems planning use. A user oriented catalog system, data set management, a network communication system, and a user interface are also discussed.
Computer programs for degaussing, magnetic field calculation, low speed wing flap systems aerodynamics, structural panel analysis, dynamic stress/strain data acquisition, allocation and network scheduling, and digital filters are discussed.