Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LAND”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Comparison of flying qualities derived from in-flight and ground-based simulators for a jet-transport airplane for the approach and landing pilot tasks

The primary objective was to provide information to the flight controls/flying qualities engineer that will assist him in determining the incremental flying qualities and/or pilot-performance differences that may be expected between results obtained via ground-based simulation (and, in particular, the six-degree-of-freedom Langley Visual/Motion Simulator (VMS)) and flight tests. Pilot opinion and performance parameters derived from a ground-based simulator and an in-flight simulator are compared for a jet-transport airplane having 32 different longitudinal dynamic response characteristics. The primary pilot tasks were the approach and landing tasks with emphasis on the landing-flare task. The results indicate that, in general, flying qualities results obtained from the ground-based simulator may be considered conservative-especially when the pilot task requires tight pilot control as during the landing flare. The one exception to this, according to the present study, was that the pilots were more tolerant of large time delays in the airplane response on the ground-based simulator. The results also indicated that the ground-based simulator (particularly the Langley VMS) is not adequate for assessing pilot/vehicle performance capabilities (i.e., the sink rate performance for the landing-flare task when the pilot has little depth/height perception from the outside scene presentation).

Grantham, William D.↗

Pinpoint landing concepts for the Mars Rover Sample Return mission

From knowledge of hazards gained following Viking, several approaches are being pursued for making the Mars Rover Sample Return (MRSR) landing safer. With the pinpoint landing capability approach, a single landing site would be certified in advance of initiating the descent orbit, using pictures transmitted to earth from the orbiter. Onboard instruments would guide the lander to follow mapped terrain to the selected site. If navigation proves insufficiently accurate, a small number of scattered sites would be certified, and the lander would select the most accessible one in real time. Some early-site certification and navigation concepts are discussed. Some of the key problems to overcome include how to recognize hazards too small to be transmitted to earth, how to represent terrain features in the flight computer, how to overcome errors in inertial measurements during landing of over 12-hour duration, how to find the selected site in real time, and how to navigate to the selected site once it is found.

Klumpp, Allan R.↗

Flight evaluations of several hover control and display combinations for precise blind vertical landings

Several control and display concepts were evaluated on a variable-stability helicopter prior to future evaluations on a modified Harrier. The control and display concepts had been developed to enable precise hover maneuvers, station keeping, and vertical landings in simulated zero-visibility conditions and had been evaluated extensively in previous piloted simulations. Flight evaluations early in the program revealed several inadequacies in the display drive laws that were later corrected using an alternative design approach that integrated the control and display characteristics with the desired guidance law. While hooded, three pilots performed landing-pad captures followed by vertical landings with attitude-rate, attitude, and translation-velocity-command control systems. The latter control system incorporated a modified version of state-rate-feedback implicit-model following. Precise landing within 2 ft of the desired touchdown point were achieved.

Schroeder, J. A.↗

Autonomous landing on Mars

Long communication times between earth and Mars demand autonomous landing capabilities. If high-resolution imagery acquired from an orbiter is available to select and certify a specific safe landing site or sites, navigational updates relative to the surface can be used to achieve the necessary accuracy to land within these certified sites. Autonomous registrations of the orbiter's imagery with photographs of the landing area taken by the lander during descent can provide the necessary accuracy and robustness. If orbital imagery is not available, autonomous hazard recognition and avoidance will be required to guide the lander to a hazard-free site. Feature extraction and matching algorithms, applied to visible light imagery and optimized to the terrain discovered by the Viking landers, can provide both an accurate surface-relative navigational update capability and a hazard recognition capability.

Stevenson, John↗

Lunar base launch and landing facilities conceptual design

The purpose of this study was to perform a first look at the requirements for launch and landing facilities for early lunar bases and to prepared conceptual designs for some of these facilities. The emphasis of the study is on the facilities needed from the first manned landing until permanent occupancy, the Phase 2 lunar base. Factors including surface characteristics, navigation system, engine blast effects, and expected surface operations are used to develop landing pad designs, and definitions fo various other elements of the launch and landing facilities. Finally, the dependence of the use of these elements and the evolution of the facilities are established.

Phillips, Paul G.↗

Understanding land surface evapotranspiration with satellite multispectral measurements

Quantitative use of remote multispectral measurements to study and map land surface evapotranspiration has been a challenging issue for the past 20 years. Past work is reviewed against process physics. A simple two-layer combination-type model is used which is applicable to both vegetation and bare soil. The theoretic analysis is done to show which land surface properties are implicitly defined by such evaporation models and to assess whether they are measurable as a matter of principle. Conceptual implications of the spatial correlation of land surface properties, as observed by means of remote multispectral measurements, are illustrated with results of work done in arid zones. A normalization of spatial variability of land surface evaporation is proposed by defining a location-dependent potential evaporation and surface temperature range. Examples of the application of remote based estimates of evaporation to hydrological modeling studies in Egypt and Argentina are presented.

Menenti, M.↗

Modeling the effect of land use on carbon storage in the forests of the Pacific Northwest

There is concern as to how the balance of carbon in the terrestrial ecosystem will change in response to a variety of land use practices. A study is described in which a methodology is being developed to help narrow this uncertainty for the temperate forets of the Pacific Northwest region of the US. A carbon storage model is being developed to respond to forest harvesting, the dominant use of land in the region. By linking the carbon model to satellite imagery and a climate simulation model, the current amount of carbon stored in the forests of the Pacific northwest is estimated. The archive of Landsat multispectral scanner (MSS) images permits a 20-year historical perspective of land use changes in the region. With these data, the recent impact of regional land use in forest carbon stores is assessed.

Cohen, Warren B.↗

The Effect of Propellers and Nacelles on the Landing Speeds of Tractor Monoplanes

This paper reports wind-tunnel tests giving the lift coefficients of large-scale wing-nacelle combinations both with and without the propeller. The tests were made to show the effect of nacelles, and idling and stopped propellers on the landing speeds of tractor monoplanes. Four types of nacelles with various cowlings were used in numerous positions with respect to both a Clark Y and a thick airfoil. The effect of both the idling and stopped propeller on lift, and consequently on landing speed, was negligible. A nacelle with exposed engine cylinders when placed directly in front of an airfoil caused a slight reduction in lift, consequently an increase in landing speed, over the condition with the wing alone. With this exception no appreciable effect on landing speed was indicated for any of the other combinations.

Windler, Ray↗

First Landing of Bell X-2 Research Airplane

The Bell X-2 supersonic research airplane is equipped with a skid main landing gear and a nose wheel. Pending completion of the rocket engine, glide flights are being performed to determine low-speed handling qualities of the airplane and the landing characteristics with the skid-type landing gear. The present paper presents data obtained during the approach and landing of the X-2 airplane on its first flight .

Richard E. Day↗

Dynamic and Flight Tests on Rubber-Cord and Oleo-Rubber-Disk Landing Gears for an F6C-4 Airplane

The investigation described in this report was conducted for the purpose of comparing an oleo-rubber-disk and a rubber-cord landing gear, built for use on an F6C-4 airplane. The investigation consisted of drop tests under various loading conditions and flight tests on an F6C-4 airplane. In the drop tests the total work done on each gear and the work done on each of the shock-absorbing units were determined. For both drop tests and flight tests the maximum loads and accelerations were determined. The comparative results showed that the oleo gear was slightly superior in reducing the ordinary landing shocks, that it had a greater capacity for work, and that it was very superior in the reduction of the rebound. The results further showed that for drops comparable to very severe landings, the rubber-cord gear was potentially more effective as a shock-reducing mechanism. However, due to the construction of this chassis, which limited the maximum elongation of the cords, this gear was incapable of withstanding as severe tests as the oleo gear. The action of the oleo gear was greatly inferior to the action of an ideal gear. The maximum accelerations encountered during the flight tests for severe landings were 3.64g for the rubber-cord gear and 2.27g for the oleo gear. These were less than those experienced in free drops of 7 inches on either gear.

Peck, William C↗

An evaluation with the Fourier Amplitude Sensitivity Test (FAST) of which land-surface parameters are of greatest importance in atmospheric modeling

Land-surface parameterizations based on a statistical-dynamical have been suggested recently to improve the representation of the surface forcing from heterogeneous land in atmospheric models. With this approach, land-surface characteristics are prescribed by probability density functions (PDFs) rather than single 'representative' values as in 'big-leaf' parameterizations. Yet the use of many PDFs results in an increased computational burden and requires the complex problem of representing covariances between PDFs to be addressed. In this study, a sensitivity analysis of a land-surface parameterization for atmospheric modeling was performed to evaluate the surface parameters most important to the variability of surface heat fluxes. The Fourier amplitude sensitivity test (FAST) used for this analysis determines the relative contribution of individual input parameters to the variance of energy fluxes resulting from a heterogeneous surface. By simultaneously varying all parameters according to their individual probability density functions, the number of computations needed is very much reduced by this technique. This analysis demonstrates that most of the variability of surface heat fluxes may be described by the distributions of relative stomatal conductance and surface roughness. Thus, the statistical-dynamical approach may be simplified by the use of only these two probability density functions.

Collins, Dan C.↗

Mars Pathfinder Landing Site Workshop

The Mars Pathfinder Project is an approved Discovery-class mission that will place a lander and rover on the surface of the Red Planet in July 1997. The Mars Pathfinder Landing Site Workshop was designed to allow the Mars scientific community to provide input as to where to land Pathfinder on Mars. The workshop was attended by over 60 people from around the United States and from Europe. Over 20 landing sites were proposed at the workshop, and the scientific questions and problems concerning each were addressed. The workshop and the discussion that occured during and afterward have significantly improved the ability to select a scientifically exciting but safe landing site on Mars.

Golombek, Matthew↗

Pathfinder landing sites at candidate SNC impact ejection sites

If Mars Pathfinder were able to land at a site on Mars from which the SNC meteorites were ejected by impact, the Pathfinder mission would essentially represent a very inexpensive sample return mission. Geologic units that contain four potential impact craters from which SNC meteorites could have been ejected from Mars are accessible to the Mars Pathfinder lander. Determining that SNC meteorites came from a particular spot on Mars raises the intriguing possibility of using Pathfinder as a sample return mission and providing a radiometric age for the considerably uncertain martian crater-age timescale. Pathfinder instruments are capable of determining if the rock type at the landing site is similar to that of one or more of the SNC meteorites, which would strengthen the hypothesis that the SNC meteorites did, in fact, come from Mars. Unfortunately, instrument observations from Pathfinder are probably not capable of determining if the geologic unit sampled by the lander is definitively the unit from which a SNC meteorite came from as opposed to Mars in general or perhaps a particular region on Mars. This abstract evaluates the possibility of landing at potential SNC ejection sites and the ability of Pathfinder to identify the landing site as the place from which an SNC meteorite came.

Golombek, Matthew P.↗

Scientific rationale for selecting northwest Isidis Planitia (14 deg - 17 deg N latitude, 278 deg - 281 deg longitude) as a potential Mars Pathfinder landing site

The northwest Isidis Basin offers a unique opportunity to land near a fretted terrain lowland/upland boundary that meets both the latitudinal and elevation requirements imposed on the spacecraft. The landing site lies east of erosional scarps and among remnant massif inselbergs of the Syrtis Major volcanic plains. The plains surface throughout Isidis exhibits abundant, low-relief mounds that are the local expression of the 'thumbprint terrain' that is common within a few hundred kilometers of the lowland/upland boundary. The massif inselbergs are not as numerous nor as massive as those fretted terrains to the northwest, so local slopes are not expected to be steep. Neither feature should pose a serious threat to the lander. Landing on or adjacent to one of these features would enhance the science return and would help to pinpoint the landing site in Viking and subsequent orbiter images by offering views of landmarks beyond the local horizon.

Parker, Tim J.↗

Rocket-based combined-cycle (RBCC) powered spaceliner class vehicle can advantageously employ vertical takeoff and landing (VTOL)

The subject is next generation orbital space transporation, taken to be fully reusable non-staged 'aircraft like' systems targeted for routine, affordable access to space. Specifically, the takeoff and landing approach to be selected for such systems is considered, mainly from a propulsion viewpoint. Conventional wisdom has it that any transatmospheric-class vehicle which uses high-speed airbreathing propulsion modes (e.g., scramjet) intrinsically must utilize horizontal takeoff and landing, HTOHL. Although this may be true for all-airbreathing propulsion (i.e., no rocket content as in turboramjet propulsion), that emerging class of powerplant which integrally combines airbreathing and rocket propulsion, referred to as rocket-based combined-cycle (RBCC) propulsion, is considerably more flexible with respect to selecting takeoff/landing modes. In fact, it is proposed that any of the modes of interest may potentially be selected: HTOHL, VTOHL, VTOVL. To illustrate this surmise, the case of a previously documented RBCC-powered 'Spaceliner' class space transport concept, which is designed for vertical takeoff and landing, is examined. The 'RBCC' and 'Spaceliner' categories are first described for background. Departing form an often presumed HTOHL baseline, the leading design and operational advantages of moving to VTOVL are then elucidated. Technical substantiation that the RBCC approach, in fact, enables this capability (but also that of HTOHL and VTOVL) is provided, with extensive reference to case-in-point supporting studies. The paper closes with a set of conditional surmises bearing on its set of conclusions, which point up the operational cost advantages associated with selecting the vertical takeoff and landing mode combination (VTOL), uniquely offered by RBCC propulsion.

Escher, William J. D.↗

Vertical landing on an asteroid

This work is concerned with the final approach phase and vertical landing on an asteroid with a power-limited, electrically propelled spacecraft. With gravitational effects taken into account, a new solution to the fuel optimal vertical landing on an asteroid was obtained. In this solution, the spacecraft commanded acceleration is explicitly expressed as a function of vehicle velocity and time to go. Based on qualitative methods of analysis, the guidance strategy and the resulting trajectories were studied. It is shown that these fuel-optimal trajectories effectively assure a vertical soft landing on the asteroid. Results of numerical simulations for the vertical landing, starting from an elliptical orbit are presented.

Harel, D.↗

The NASA landing gear test airplane

A tire and landing gear test facility has been developed and incorporated into a Convair 990 aircraft. The system can simulate tire vertical load profiles to 250,000 lb, sideslip angles to 15 degrees, and wheel braking on actual runways. Onboard computers control the preprogrammed test profiles through a feedback loop and also record three axis loads, tire slip angle, and tire condition. The aircraft to date has provided tire force and wear data for the Shuttle Orbiter tire on three different runways and at east and west coast landing sites. This report discusses the role of this facility in complementing existing ground tire and landing gear test facilities, and how this facility can simultaneously simulate the vertical load, tire slip, velocity, and surface for an entire aircraft landing. A description is given of the aircraft as well as the test system. An example of a typical test sequence is presented. Data collection and reduction from this facility are discussed, as well as accuracies of calculated parameters. Validation of the facility through ground and flight tests is presented. Tests to date have shown that this facility can operate at remote sites and gather complete data sets of load, slip, and velocity on actual runway surfaces. The ground and flight tests have led to a successful validation of this test facility.

Carter, John F.↗

The Aggregate Representation of Terrestrial Land Covers Within Global Climate Models (GCM)

This project had four initial objectives: (1) to create a realistic coupled surface-atmosphere model to investigate the aggregate description of heterogeneous surfaces; (2) to develop a simple heuristic model of surface-atmosphere interactions; (3) using the above models, to test aggregation rules for a variety of realistic cover and meteorological conditions; and (4) to reconcile biosphere-atmosphere transfer scheme (BATS) land covers with those that can be recognized from space; Our progress in meeting these objectives can be summarized as follows. Objective 1: The first objective was achieved in the first year of the project by coupling the Biosphere-Atmosphere Transfer Scheme (BATS) with a proven two-dimensional model of the atmospheric boundary layer. The resulting model, BATS-ABL, is described in detail in a Masters thesis and reported in a paper in the Journal of Hydrology Objective 2: The potential value of the heuristic model was re-evaluated early in the project and a decision was made to focus subsequent research around modeling studies with the BATS-ABL model. The value of using such coupled surface-atmosphere models in this research area was further confirmed by the success of the Tucson Aggregation Workshop. Objective 3: There was excellent progress in using the BATS-ABL model to test aggregation rules for a variety of realistic covers. The foci of attention have been the site of the First International Satellite Land Surface Climatology Project Field Experiment (FIFE) in Kansas and one of the study sites of the Anglo-Brazilian Amazonian Climate Observational Study (ABRACOS) near the city of Manaus, Amazonas, Brazil. These two sites were selected because of the ready availability of relevant field data to validate and initiate the BATS-ABL model. The results of these tests are given in a Masters thesis, and reported in two papers. Objective 4: Progress far exceeded original expectations not only in reconciling BATS land covers with those that can be recognized from space, but also in then applying remotely-sensed land cover data to map aggregate values of BATS parameters for heterogeneous covers and interpreting these parameters in terms of surface-atmosphere exchanges.

Shuttleworth, W. James↗