Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HARDNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A Feasibility Study on Use of an Accelerometer to Measure the Dynamic Forces in Turning

Metal cutting is a highly dynamic process that generates continuously varying forces. Measurement of these forces is essential to characterizing a cutting process and to fully utilize the machine tool. A force dynamometer is often used to measure these varying forces; however, it is limited by the natural frequency of the sensor and can sometimes be hard to set up on a machine. Therefore, this study aims to estimate the dynamic component of the cutting force using an accelerometer placed directly below the cutting edge. The placement of the sensor helps achieving better signal to noise ratio (S/N). The cutting tool is modelled as a single degree of freedom (SDOF) system relative to the workpiece and dynamic loads are experimentally simulated on it. The measured acceleration is numerically integrated to obtain velocity and deflection, which along with the natural frequency (ω n ) and damping ratio (ζ), is used to predict the dynamic load using the system equation. The dynamic forces tested over a wide range of frequencies, show good agreement with the data from simultaneous dynamometer measurement and the force estimated using the proposed method. The study shows the feasibility of this method in a real cutting scenario and the capability to apply it to a multi DOF system. One major limitation is the inability to capture the static or quasi-static component of the cutting force.

Cutting vibrations↗
DOE OSTI2025

Unit cell manufacture by blown powder directed energy deposition

Lattice structures manufactured by additive manufacturing show unique promise to alter existing components to improve the thermo-mechanical properties of the base structure. Here, in the present study, the manufacture of a self-supporting lattice structure by blown powder directed energy deposition was explored. Converging struts were manufactured using multiple lean angles to facilitate the self-supporting structure and to avoid machine-part collisions. The struts showed near uniform straightness relative to a fitted line with a maximum deviation of 1mm at a lean angle of 10°. Micro–hardness and porosity evaluation results showed no significant variation along the struts.

Additive manufacturing↗
DOE OSTI2025

Assessment of the grindability of robocast silicon carbide

The demand for high-performance lightweight optics has driven interest in silicon carbide (SiC) due to its exceptional thermal stability, hardness, and strength-to-weight ratio. This study investigates the potential of robocasting, an additive manufacturing process, as a viable method for producing lightweighted SiC components for optical applications. Four samples with varied starting powder phases (α and β) and sintering conditions were fabricated and evaluated. Post-sintering surface and form were assessed using coherence scanning interferometry (CSI) and coordinate measuring machine (CMM) techniques. A three-stage grinding process was applied to each sample, with surface roughness assessed at each stage. Results demonstrate that samples with predominantly α-phase SiC and smaller particle sizes achieved superior surface finish, particularly sample D2-α-2135 °C, which displayed the lowest post-grinding Sq value of 0.178 µm. The analysis also indicated no significant print-through effect from the lightweighting structure, or print artifacts, at this stage of grinding. However, β-phase samples showed poorer grindability, increased surface roughness, and pitting. These findings suggest that phase composition and particle size are critical for achieving the desired surface quality in robocast SiC optics. Future work will incorporate additional samples and finer grinding wheels to refine surface quality further, supporting the development of SiC for high-precision optical applications.

Barrett, Taylor [ORNL]↗
DOE OSTI2024

Gas-phase surface modification to control catalyst structure and yields in methane dehydroaromatization

Methane dehydroaromatization (MDA) is a promising approach for direct methane transformation to aromatics and hydrogen. The benchmark catalyst Mo/H-ZSM-5 struggles to find commercial adoption because of thermodynamically-limited yields and rapid coking on Brønsted acid and molybdenum carbide species, especially on zeolite external surfaces. Here, gas-phase atomic layer deposition (ALD) overcoats H-ZSM-5 external surfaces with SiO 2 or Al 2 O 3 . NH 3 -TPD, HRTEM, and textural properties show that these overcoats exclusively passivate zeolite external surfaces. Under MDA conditions, SiO 2 gives softer coke and increases cumulative benzene yields by 25%, while Al 2 O 3 strongly decreases yields. H 2 -TPR and UV-visible and Raman spectroscopy show how the overcoats redisperse the MoO x precatalysts, especially over multiple deactivation and isothermal oxidative regeneration cycles. Combined with 27 Al-MAS NMR, MoO x redistribution and dealumination are seen as the causes of long-term deactivation over multiple regeneration cycles, and this process continues to occur regardless of the overcoat. Altogether, the deposition of a small amount of silica on the outer surface of Mo/H-ZSM-5 reduces the formation of hard coke, which could be regenerated by milder methods such as hydrogen treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Evaluating switch lifetime in soft-switched single-stage differential-mode SST

The reliability of semiconductor switches in single-stage differential-mode solid-state transformers (DM-SSTs) has not been systematically evaluated under soft-switching operation and realistic grid conditions. This paper presents a switch-level reliability analysis for soft-switched and hard-switched DM-SST configurations by integrating converter-specific power loss modeling with empirical lifetime prediction. Analytical derivation of device current profiles specific to the DM-SST is used to characterize electrothermal stress, which is then mapped to lifetime using degradation models obtained from power cycling tests (PCTs). Applied to realistic SST load profiles and grid voltage variations, this approach provides a probabilistic prediction of switch lifetime for the DM-SST. Lifetime estimates for both SiC MOSFETs and Si IGBTs are presented, offering insight into device degradation under converter operating conditions. The results quantify the reliability benefits of soft switching in single-stage SSTs, highlighting how switching dynamics influence long-term switch degradation.

14 SOLAR ENERGY↗
DOE OSTI2023

Modeling aqueous association constants and mineral solubilities at subcritical and supercritical temperatures

The need for sustainable power generation has increased interest in the use of hydrothermal fluids for industrial applications. New high-enthalpy geothermal systems and biowaste-to-fuel processes are two relevant examples that employ supercritical fluids which require an in-depth understanding of complex chemical reactions occurring near the supercritical temperature of water (374 °C). As these processes operate in thermodynamic regimes that are not currently covered by a standard molar Gibbs energy of formation model, only empirical fits for single reaction systems are available which limit the use of multi-component phase equilibria calculations that are standard practice for less extreme environments. Here, in this paper, we advance a standard molar Gibbs energy of formation model able to operate in these otherwise inaccessible thermodynamic states to include species needed for key mineral solubility systems and ion association reactions. This work extends a model based on molecular statistical thermodynamics (MST) into four new systems (Na 3 PO 4 -H 2 O, LiOH-H 2 O, KOH-H 2 O, and BaSO 4 -H 2 O) by extending the model to cover 10 new species. For each of these systems, model predictions were consistently within the experimental uncertainties for the new systems covered. A breakdown of MST contributions to the model revealed that electrostatic and hard sphere contributions were key to reproducing density dependencies of standard molar Gibbs energy of formation values around the critical point of water.

42 ENGINEERING↗
DOE OSTI2020

Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting

In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Elevated temperature mechanical properties of Inconel 617 surface oxide using nanoindentation

Inconel 617 is a principal candidate material for helium gas cooled very-high-temperature reactors with outlet temperatures of 700–950 °C. Recent findings showed that this alloy develops unique surface oxide layers especially at high temperature (HT) helium environment with distinctive wear, friction and contact properties. This study investigates the elevated temperature mechanical properties of Inconel 617 top surface layers aged in HT helium environment. Nanoindentation technique is used to obtain load-displacement graphs of the alloy top surface oxide in temperatures ranging from 25 °C up to 600 °C. In addition, using finite element analysis along with an iterative regression technique, a semi-numerical method is developed to further measure and quantify the material parameters and, in particular, time-independent and creep characteristics of the oxide. Although Young's modulus of the oxide is found to be relatively close to the bulk for the tested temperatures, the yield strength and hardness, in comparison to the bulk material, increase significantly as the material is oxidized after aging. The oxide exhibits significant softening as the temperature increases to 600 °C. Unlike the bulk material, diffusion through the grains is found to be the dominant creep mechanism for the oxide. Considerable difference between the mechanical properties of the oxide and the bulk material shows the need for accurate measurements of near surface mechanical properties, if reliable predictive contact and tribological models are sought at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

AA2024/SiC metal matrix composites simultaneously improve ductility and cracking resistance during elevated temperature deformation

Here this study uses the stir-casting technique to combine a semi-solid AA2024 alloy directly with finely-sized β-SiC p embedded as a powder or with mechanically alloyed granules as a delivery agent. Liquid-state primary fabrication tends to form agglomerates of reinforcement particles, whereas rolling better distributes the composite constituents. Sub-micron reinforcements of low volume fractions do not significantly increase the hardness of the composite materials. Uniaxial tensile testing at elevated temperatures over a wide range of strain rates showed simultaneous increases in the ductility and crack resistance of AA2024 + SiC p granules embedded as a powder when compared to the non-reinforced control material at lower strain rates, with the same toughness as the control material. The maximum engineering strain of 252.7 ± 19.2% was observed in AA2024/SiCp at a strain rate of 10 -4 s -1 . This improvement in properties is attributed to grain refinement in the MMCs, leading to pinning events during the straining and ductility increases. The resultant impediments to grain growth and crack propagation allow the fine-sized reinforcements to control dynamic microstructural changes during fatigue. Cube {001}<100> is a dominant texture component in AA2024, whereas the Goss {011}<100> and S {123}<634> components mainly represent the texture of the discontinuously reinforced aluminum matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and mechanical properties of nanoscale Cu/(Ta50Nb25Mo25) multilayers

Nanoscale Cu/(Ta50Nb25Mo25) multilayers comprised of medium entropy alloy Ta50Nb25Mo25 and pure Cu are found to exhibit similar length-scale-dependent deformation mechanisms as metallic multilayers with elemental individual layers, i.e., confined layer slip at layer thickness of tens of nanometers and shear localization at several nanometers. The hardness of the nanoscale Cu/(Ta50Nb25Mo25) multilayers is higher as compared to the pure element FCC/BCC multilayers due to the extra solid solution strengthening contribution in the BCC layer. The synergy between the size effect and solid solution strengthening mechanism is discussed. In conclusion, this is an early report of the multi-component multilayers, which serves to provide directions for developing novel multilayer materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Prediction of softening kinetics and recrystallization texture in non-isothermally annealed bulged tubes using CPFEM and CA models

A hierarchically coupled cellular automata (CA) model, crystal plasticity finite element method (CPFEM), and thermal finite element (FE) model is developed to predict the softening kinetics of the bulged steel tube during non-isothermal annealing. Through the developed model, the kinetics of softening mechanisms including static recovery (SRV) and static recrystallization (SRX), as well as the recrystallization texture are predicted. Later, the Johnson-Mehl-Avrami-Kohnogorov (JMAK) model based on the predicted SRX data is developed to interpret the recrystallization behavior of the material. To perform this study, diverse experimental tests including tube hydroforming (THF), annealing, uniaxial tensile test, hardness test, as well as microstructure observations through optical microscopy and Electron Backscatter Diffraction (EBSD) tests on steel tube are performed. The obtained experimental data are utilized to calibrate and verify the implemented CPFEM model for simulation of THF process, thermal FE model for prediction of the local temperature over annealing time, and CA algorithm for modeling of the softening kinetics and texture evolution throughout the annealing process. The study shows that the predicted deformation characteristics, softening kinetics, recrystallization texture and temperature profile during non-isothermal annealing are in good agreement with experimental data. During the annealing process, a total of four stages for the kinetics of softening mechanisms is observed: No softening; SRV only; SRV dominant; and SRX dominant. During the progress of SRX, the behavior of recrystallization is abruptly changed, confirming that two different mechanisms are controlling the kinetics of transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Self-equilibrated backstresses induce compensation between hardening and softening: Micromechanical and microstructural features

For crystal plasticity formulation neglecting the strain gradients at the dislocation scale, backstresses are necessary to satisfy the mesoscopic stress equilibrium and strain compatibility requirements. Backstresses in a material point and those between neighboring points are treated separately. Physically backstresses can dynamically induce either hardening or softening effects to adjust the dislocation hardening of slip systems, whereas the sum of the stresses resulting in backstresses in the representative volume element (RVE) is zero. Backstress hardening suppresses certain slip activities, while backstress softening triggers excess dislocations. A two-phase brass is studied. Backstresses make the hard phase deform smaller and the soft phase deform more than those without employing backstresses in a model. In the former, more homogeneous lattice strain and higher yield stress are obtained. Backstress has limited effects on the evolution of the critical resolved shear stress and crystallographic texture. Furthermore, it is a major cause of the banded structures featuring sharp crystallographic contrasts which are not parallel to the slip planes. Tests indicate that backstress induces a serrated behavior at the early stages of deformation and induces the geometrically necessary bands (GNBs), which are parallel to the macroscopic axes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Deformation mechanisms in single crystal Ni-based concentrated solid solution alloys by nanoindentation

Nanoindentation is a critical technique to probe mechanical properties at the micrometer and sub-micrometer scales, accompanied by challenges from indentation size effect, pile-up/sink-in effect, and strain rate sensitivity. In this work, different nanoindentation techniques have been employed to explore Ni-based concentrated solid solution alloys (CSAs) with the addition of 3d transition metal elements including Co, Cr, Mn, and Fe, including unique single-crystal Ni, NiCo, NiFe, Ni 80 Cr 20 , and NiCoFeCr samples with (100) surfaces. A procedure of nanoindentation tests and data analysis/correction have been developed, and a data set of hardness, elastic modulus, strain rate sensitivity, and activation volume for Ni-based CSAs are provided, including the less explored binary alloys such as Ni 80 Cr 20 and Ni 80 Mn 20 . The results show that the type of alloying elements is more critical than the number of elements in strengthening: Co does not provide strengthening in NiCo, while Cr, Mn, and Fe are effective strengthening elements. Cr is the most effective among all the 3d transition metal elements. Furthermore, atomic-level lattice distortion is responsible for the strengthening and the role of stacking fault energy is insignificant in Ni-based CSAs at room temperature. In summary, nanoindentation shows increasing promise as a reliable and fast tool to provide comprehensive mechanical information for new alloy design and development.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and mechanical properties of hypoeutectic Al–6Ce–3Ni-0.7Fe (wt.%) alloy

Here, a hypoeutectic, Fe-modified Al–Ce–Ni alloy (Al–6Ce–3Ni-0.7Fe, wt.%) is studied in terms of microstructure, thermal stability, ambient temperature strengthening, and creep resistance. The as-cast microstructure consists of primary Al dendrites and interdendritic binary eutectic regions (Al–Al11Ce3 and/or Al–Al9(Fe,Ni)2), with micron/submicron lamellar spacing, depending on the location along the height of the ingot. The cast alloy exhibits excellent coarsening resistance at 400 °C, with mostly unchanged microstructure and microhardness after 6 weeks of aging, indicating good thermal stability of Al11Ce3 and Al9(Fe,Ni)2. Orowan strengthening and load transfer are identified as strengthening mechanisms at ambient and elevated temperature. A high volume fraction of the intermetallic phases (providing load transfer) and relatively coarse eutectic spacing (for modest Orowan strengthening) result in a moderate as-cast microhardness of 566 ± 32 MPa. Creep resistance at 300 and 350 °C is similar to a binary Al-12.5Ce eutectic alloy (with twice the Ce content) because of two countering effects: Al–6Ce–3Ni-0.7Fe shows a higher volume fraction of strengthening intermetallic phases, but it also exhibits a large fraction of primary Al dendrites which weaken the alloy. By contrast, the alloy, when laser-remelted at the surface, has a fully eutectic microstructure without primary aluminum dendrites achieved by high undercooling on solidification, with a refined network of eutectic phases that doubles the microhardness as compared to the cast alloy. Whereas coarsening is faster due to the shorter diffusion distances between the eutectic phases, hardness remains ~30% higher than the as-cast alloy after ~6 weeks aging at 400 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exceptional thermal stability of additively manufactured CoCrFeMnNi high-entropy alloy with cellular dislocation structures

CoCrFeMnNi high-entropy alloy (HEA) was additively manufactured (AM) by laser powder-bed fusion (L-PBF). The AM CoCrFeMnNi has prominent cellular dislocation structures with a small number of Mn-rich oxides. The thermal stability of the AM CoCrFeMnNi was investigated by isochronal annealing treatment at various temperatures from 400 to 1300°C for 1h. Microstructural analysis shows slow dislocation recovery, retarded recrystallization process, and precipitation of additional Cr-Mn based oxides during thermal annealing, resulting in exceptional thermal stability and retained high hardness at elevated temperatures. Further, by thermodynamic calculations, a low stored energy of 1.31 MJ/m 3 and a high activation energy of 353 kJ/mol for recrystallization were estimated for the AM CoCrFeMnNi. The exceptional thermal stability of the AM CoCrFeMnNi HEA is mechanistically attributed to the low crystallographic misorientations across the dislocation cell walls, sluggish atomic diffusion, and the pinning effects of the oxide nanoprecipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Alloying effects on the microstructure and properties of laser additively manufactured tungsten materials

A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in their application for extreme environments. However, cracking and additional embrittling features at grain boundaries have resulted in poorly performing materials, stymying the application of AM as a manufacturing technique for W. Several alloying strategies, such as ceramic particles and ductile elements, have emerged with the promise to eliminate cracking while simultaneously enhancing stability against recrystallization. Here, in this work, we provide new insights regarding the defects and microstructural features that result from the introduction of ZrC for grain refinement and NiFe as a ductile reinforcement phase – in addition to the resulting thermophysical and mechanical properties. ZrC is shown to promote microstructural stability with increased hardness due to the formation of ZrO 2 dispersoids. Conversely, NiFe forms into micron-scale FCC phase regions within a BCC W matrix, producing enhanced toughness relative to pure AM W. A combination of these effects is realized in the WNiFe + ZrC system and demonstrates that complex chemical environments coupled with the tuning of AM microstructures provides an effective pathway for enabling laser AM W materials with enhanced stability and performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗