Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLORIDA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

Indoor Climate and Moisture Durability Performances of Houses with Unvented Attic Roof Constructions in a Mixed-Humid Climate

A sealed or unvented attic is an energy-efficient envelope component that can reduce the amount of energy a house consumes for space conditioning if the air handler and/or ducts are located in the attic. The attic is typically sealed by using spray foam on the underside of the roof deck and covering the soffit, ridge and gable vents to minimize air leakage from the attic to the outside. This approach can save up to 10% in space-conditioning energy when ducts are located in the attic (DOE 2013). Past research done by ORNL and Florida Solar Energy Center suggests that in more hot, humid climates, an unvented attic could potentially create a more humid, uncomfortable living environment than a vented attic (Colon 2011, Boudreaux, Pallin et al. 2013). Research showed that controlling the higher indoor humidity could reduce the energy savings from the sealed, unvented attic, which in turn would decrease the energy savings payback. Research also showed that the roof assembly (5.5 inches of open-cell foam, 1inch of closed-cell foam, OSB, felt paper, and asphalt shingles) stored moisture, thus acting as a moisture buffer. During the fall and winter, the roof assembly stored moisture and during the spring and summer it released moisture. This phenomenon is not seen in a vented attic, in which the air exchange rate to the outside is greater and, in the winter, helps to dehumidify the attic air. It was also seen that in a vented attic, the direction of water vapor diffusion is on average from the attic to the interior of the house. Air leakage from the attic to the interior also occurs during more of the year in a house with an unvented attic than in one with a vented attic. These discoveries show that the moisture dynamics in a house with an unvented attic are much different from those in a house with a vented attic. This study reports on a series of computer model investigations completed to determine the key variables impacting indoor comfort and the durability of roof assemblies against moisture. The key variables investigated were the leakage area from the attic to the outside, leakage area from the attic to the interior, leakage area from the interior to the outside, supply duct leakage in the attic, and interior moisture generation. These investigations are described in this report.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Measured Performance of Occupied, Side-by-Side, South Texas Homes

The performance of three homes in San Antonio, Texas with identical floor plans and orientation were evaluated through a partnership between the Florida Solar Energy Center (FSEC), CPS Energy, and Woodside Homes of South Texas. Measurements included whole house gas and electric use as well as heating, cooling, hot water, major appliances and indoor and outdoor conditions. One home built to builder standard practice served as the control, while the other homes demonstrated high performance features. Utility peak electric load comparisons of these dual-fuel homes provide an assessment of envelope and equipment improvements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Expert Meeting Report: Key Innovations for Adding Energy Efficiency to Maintenance Projects

This report describes an expert meeting hosted by the Building America research team NAHB Research Center, which was held on February 8, 2012, in Orlando, Florida. The topic focused on efforts to increase the efficiency of existing homes, specifically for re-roofing and the opportunities for adding energy efficiency upgrades during this major home repair activity.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Assessing the Energy Savings of Tankless Water Heater Retrofits in Public Housing

This report describes the methodology, analysis, and findings from a case study of a 110 unit retrofit of gas tankless water heaters in a hot/humid climate in Alachua County, Florida. The gas-fired tank type water heaters in the housing units were replaced with gas-fired tankless water heaters as part of a federal program that targeted reduced energy use in public housing.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Variability in Measured Space Temperatures in 60 Homes

This report discusses the observed variability in indoor space temperature in a set of 60 homes located in Florida, New York, Oregon, and Washington. Temperature data were collected at 15-minute intervals for an entire year, including living room, master bedroom, and outdoor air temperature (Arena, et. al). The data were examined to establish the average living room temperature for the set of homes for the heating and cooling seasons, the variability of living room temperature depending on climate, and the variability of indoor space temperature within the homes. The accuracy of software-based energy analysis depends on the accuracy of input values. Thermostat set point is one of the most influential inputs for building energy simulation. Several industry standards exist that recommend differing default thermostat settings for heating and cooling seasons. These standards were compared to the values calculated for this analysis. The data examined for this report show that there is a definite difference between the climates and that the data do not agree well with any particular standard.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Short-Term Test Results: Transitional Housing Energy Efficiency Retrofit in the Hot Humid Climate

This project evaluates the renovation of a 5,800 ft2, multi-use facility located in St. Petersburg, on the west coast of central Florida, in the hot humid climate. An optimal package of retrofit measures was designed to deliver 30%-40% annual energy cost savings for this building with annual utility bills exceeding $16,000 and high base load consumption. Researchers projected energy cost savings for potential retrofit measures based on pre-retrofit findings and disaggregated, weather normalized utility bills as a basis for simulation true-up. A cost-benefit analysis was conducted for the seven retrofit measures implemented; adding attic insulation and sealing soffits, tinting windows, improving whole building air-tightness, upgrading heating and cooling systems and retrofitting the air distribution system, replacing water heating systems, retrofitting lighting, and replacing laundry equipment. The projected energy cost savings for the full retrofit package based on a post-retrofit audit is 35%. The building's architectural characteristics, vintage, and residential and commercial uses presented challenges for both economic projections and retrofit measure construction.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Advanced Precursor Reaction Processing for Cu(InGa)(SeS)2 Solar Cells

This project “Advanced Precursor Reaction Processing for Cu(InGa)(SeS)2 Solar Cells”, completed by the Institute of Energy Conversion (IEC) at the University of Delaware in collaboration with the Department of Chemical Engineering at the University of Florida, developed the fundamental understanding and technology to increase module efficiency and improve the manufacturability of Cu(InGa)(SeS)2 films using the precursor reaction approach currently being developed by a number of companies. Key results included: (1) development of a three-step H2Se/Ar/H2S reaction process to control Ga distribution through the film and minimizes back contact MoSe2 formation; (2) Ag-alloying to improve precursor homogeneity by avoiding In phase agglomeration, faster reaction and improved adhesion to allow wider reaction process window; (3) addition of Sb, Bi, and Te interlayers at the Mo/precursor junction to produce more uniform precursor morphology and improve adhesion with reduced void formation in reacted films; (4) a precursor structure containing Se and a reaction process to reduce processing time to 5 minutes and eliminate H2Se usage, thereby increasing throughput and reducing costs. All these results were supported by detailed characterization of the film growth, reaction pathways, thermodynamic assessment and device behavior.

25 ENERGY STORAGE↗

Power Hardware-in-the-Loop-Based Anti-Islanding Evaluation and Demonstration

The National Renewable Energy Laboratory (NREL) teamed with Southern California Edison (SCE), Clean Power Research (CPR), Quanta Technology (QT), and Electrical Distribution Design (EDD) to conduct a U.S. Department of Energy (DOE) and California Public Utility Commission (CPUC) California Solar Initiative (CSI)-funded research project investigating the impacts of integrating high-penetration levels of photovoltaics (PV) onto the California distribution grid. One topic researched in the context of high-penetration PV integration onto the distribution system is the ability of PV inverters to (1) detect islanding conditions (i.e., when the distribution system to which the PV inverter is connected becomes disconnected from the utility power connection) and (2) disconnect from the islanded system within the time specified in the performance specifications outlined in IEEE Standard 1547. This condition may cause damage to other connected equipment due to insufficient power quality (e.g., over-and under-voltages) and may also be a safety hazard to personnel that may be working on feeder sections to restore service. NREL teamed with the Florida State University (FSU) Center for Advanced Power Systems (CAPS) to investigate a new way of testing PV inverters for IEEE Standard 1547 unintentional islanding performance specifications using power hardware-in-loop (PHIL) laboratory testing techniques.

14 SOLAR ENERGY↗

Discovering the desirable alleles contributing to the lignocellulosic biomass traits in saccharum germplasm collections for energy cane improvement

Phenotyping Methods: The accessions (which includes 21 taxa and 1,177 accessions) in the World Collection of Sugarcane and Related Grasses (WCSRG) was evaluated for the following traits: arenchyma, internode length and diameter, pubescence, pith, Brix, stalk number and fiber. A core of 300 accessions that included each species in the World Collection was selected by using the Maximization Strategy in MStrat software. Results: The core had a higher diversity rating than random selections of 300 accessions. The Shannon–Weaver Diversity Index scores of the core and whole collection were similar indicating that the majority of the diversity was captured by the core collection. The ranges and medians between the core and WCSRG were similar; only two of the trait medians were not significant at P = 0.05 using the non-parametric Wilcoxon method and the coincidence rate (CR % = 96.2) was high (>80) indicating that extreme values were retained. Thus, the phenotypic diversity of these traits in the WCSRG was well represented by the core collection. Associations Methods: Genotypic and phenotypic data were collected for 1002 accessions of the WCSRG including 209 SSR markers. Association analysis was performed using both General Linear (GLM) and Maximum Likelihood (MLM) models. Different core collections with 300 accessions each were selected based on genotypic, phenotypic and combined data based on the Maximization Strategy in MStrat software. Results: A major portion of the genotyping involving SNPs is being conducted by Dr. Jianping Wang of the University of Florida under the DOE award DE-FG 02-11ER 65214 and the genotypic and phenotypic associations will be reported separately next year. In the current, study forty one and seventeen markers were found to be associated with traits using the GLM and MLM methods respectively including associations with arenchyma, internode length and diameter, pubescence, pith, and Sugar Cane Yellow Leaf Virus. The data indicates that each of the cores and the World Collection are similar to each other genotypically and phenotypically, but the core that was selected using only genotypic data was significantly different phenotypically. This indicates that there is not enough association between the genotypic and phenotypic diversity as to select using only genotypic diversity and get the full phenotypic diversity. Core Collection: Creation and Phenotyping Methods: To evaluate this germplasm for breeding purposes, a representative diversity panel selected from the WCSRG of approximately 300 accessions was planted at Canal Point, FL in three replications. These accessions were measured for stalk height and stalk number multiple times throughout the growing season and Brix and fresh biomass during harvest in 2013 and, stalk height, stalk number, stalk diameter, internode length, Brix and fresh and dry biomass was determined in the ratoon crop harvest in 2014. Results: In correlations of multiple measurements, there were higher correlations for early measurements of stalk number and stalk height with harvest traits like Brix and fresh weight. Hybrids had higher fresh mass and Brix while Saccharum spontaneum had higher stalk number and dry mass. The heritability of hybrid mass traits was lower in the ratoon crop. According to the principal component analysis, the diversity panel was divided into two groups. One group had accessions with high stalk number and high dry biomass like S. spontaneum and the other groups contained accessions with higher Brix and fresh biomass like S. officinarum. Mass traits correlated with each other as expected but hybrids had lower correlations between fresh and dry mass. Stalk number and the mass traits correlated with each other except in S. spontaneum and hybrids in the first ratoon. There were 110 accessions not significantly different in Brix from the commercial sugarcane checks including 10 S. spontaneum accessions. There were 27 dry and 6 fresh mass accessions significantly higher than the commercial sugarcane checks. Core Collection: Fiber analysis Methods: A biomass sample was taken from each accession then shredded and dried. Fiber analysis was then performed on each sample. The acetyl groups, acid insoluble lignin, acid soluble lignin, arabinan, glucan, holocellulose, total lignin, structural ash, and xylan were quantified on a % fiber basis and nonstructural ash on a % total basis. Results: There were significant, but not large differences between species for holocellulose, lignin, acetyl, acid soluble lignin, nonstructural ash, and glucan. For each trait, S. spontaneum had significantly more holocellulose, glucan, lignin, and nonstructural ash and less acetyl and acid soluble lignin than the other species. In all populations, glucan and was positively correlated with holocellulose were positively correlated and glucan and and holocellulose were negatively correlated with lignin. In hybrids, internode length correlated positively with holocellulose and nonstructural ash and negatively with lignin. The heritability estimates for each of the fiber component traits is low indicating that environment is an important factor in fiber composition. Principal component analysis indicated that a large amount of diversity exists within each of the species.

09 BIOMASS FUELS↗

Validation of Heliovolt Modules at the RTCs

The purpose of the project is to design, construct, and commission up to 10 kW DC of Heliovolt’s module technologies. These PV demonstration systems are targeted for installation at: (1) Sandia’s RTC site located in Albuquerque, New Mexico, (2) Sandia’s RTC site located at Florida Solar Energy Center (FSEC) in Cocoa, FL, and (3) at NREL’s RTC site located in Aurora, CO. 5kW of PV was installed at each of these sites, but before the other 5 kW could be installed, Heliovolt Corporation ceased operations and liquidated all assets. The assets remaining at each RTC site have been legally abandoned. Sandia is currently assessing how these assets can be reused to benefit future research projects.

14 SOLAR ENERGY↗

Permafrost Active Layer Seismic Interferometry Experiment (PALSIE).

We present findings from a novel field experiment conducted at Poker Flat Research Range in Fairbanks, Alaska that was designed to monitor changes in active layer thickness in real time. Results are derived primarily from seismic data streaming from seven Nanometric Trillium Posthole seismometers directly buried in the upper section of the permafrost. The data were evaluated using two analysis methods: Horizontal to Vertical Spectral Ratio (HVSR) and ambient noise seismic interferometry. Results from the HVSR conclusively illustrated the method's effectiveness at determining the active layer's thickness with a single station. Investigations with the multi-station method (ambient noise seismic interferometry) are continuing at the University of Florida and have not yet conclusively determined active layer thickness changes. Further work continues with the Bureau of Land Management (BLM) to determine if the ground based measurements can constrain satellite imagery, which provide measurements on a much larger spatial scale.

54 ENVIRONMENTAL SCIENCES↗

Task Parallel Incomplete Cholesky Factorization using 2D Partitioned-Block Layout

We introduce a task-parallel algorithm for sparse incomplete Cholesky factorization that utilizes a 2D sparse partitioned-block layout of a matrix. Our factorization algorithm follows the idea of algorithms-by-blocks by using the block layout. The algorithm-byblocks approach induces a task graph for the factorization. These tasks are inter-related to each other through their data dependences in the factorization algorithm. To process the tasks on various manycore architectures in a portable manner, we also present a portable tasking API that incorporates different tasking backends and device-specific features using an open-source framework for manycore platforms i.e., Kokkos. A performance evaluation is presented on both Intel Sandybridge and Xeon Phi platforms for matrices from the University of Florida sparse matrix collection to illustrate merits of the proposed task-based factorization. Experimental results demonstrate that our task-parallel implementation delivers about 26.6x speedup (geometric mean) over single-threaded incomplete Choleskyby- blocks and 19.2x speedup over serial Cholesky performance which does not carry tasking overhead using 56 threads on the Intel Xeon Phi processor for sparse matrices arising from various application problems.

2D layout↗

Single-Crystal Sapphire Optical Fiber Sensor Instrumentation

This report summarizes technical progress on the program “Single-Crystal Sapphire Optical Fiber Sensor Instrumentation,” funded by the National Energy Technology Laboratory of the U.S. Department of Energy, and performed by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering at Virginia Tech. This project was completed in three phases, each with a separate focus. Phase I of the program, from October 1999 to April 2002, was devoted to development of sensing schema for use in high temperature, harsh environments. Different sensing designs were proposed and tested in the laboratory. Phase II of the program, from April 2002 to April 2009, focused on bringing the sensor technologies, which had already been successfully demonstrated in the laboratory, to a level where the sensors could be deployed in harsh industrial environments and eventually become commercially viable through a series of field tests. Also, a new sensing scheme was developed and tested with numerous advantages over all previous ones in Phase II. Phase III of the program, September 2009 to December 2013, focused on development of the new sensing scheme for field testing in conjunction with materials engineering of the improved sensor packaging lifetimes. In Phase I, three different sensing principles were studied: sapphire air-gap extrinsic Fabry-Perot sensors; intensity-based polarimetric sensors; and broadband polarimetric sensors. Black body radiation tests and corrosion tests were also performed in this phase. The outcome of the first phase of this program was the selection of broadband polarimetric differential interferometry (BPDI) for further prototype instrumentation development. This approach is based on the measurement of the optical path difference (OPD) between two orthogonally polarized light beams in a single-crystal sapphire disk. At the beginning of Phase II, in June 2004, the BPDI sensor was tested at the Wabash River coal gasifier facility in Terre Haute, Indiana. Due to business conditions at industrial partner and several logistical problems, this field test was not successful. An alternative high-temperature sensing system using sapphire wafer-based extrinsic Fabry-Perot interferometry was then developed as a significant improvement over the BPDI solution. From June 2006 to June 2008, three consecutive field tests were performed with the new sapphire wafer sensors at the TECO coal gasifier in Tampa, Florida. One of the sensors survived in the industrial coal gasifier for 7 months, over which time the existing thermocouples were replaced twice. The outcome of these TECO field tests suggests that the sapphire wafer sensor has very good potential to be commercialized. However packaging and sensor protection issues need additional development. During Phase III, several major improvements in the design and fabrication process of the sensor have been achieved through experiments and theoretical analysis. Studies on the property of the key components in the sensor head, including the sapphire fiber and sapphire wafer, were also conducted, for a better understanding of the sensor behavior. A final design based on all knowledge and experience has been developed, free of any issues encountered during the entire research. Sensors with this design performed well as expected in lab long-term tests, and were deployed in the sensing probe of the final coal-gasifier field test. Sensor packaging and protection was improved through materials engineering through testing of packaging designs in two blank probe packaging tests at Eastman Chemical in Kingsport, TN. Performance analysis of the blank probe packaging resulted in improve package designs culminating in a 3rd generation probe packaging utilized for the full field test of the sapphire optical sensor and materials designed sensor packaging.

47 OTHER INSTRUMENTATION↗

Development of Innovative Accident Tolerant High Thermal Conductivity UO 2 -Diamond Composite Fuel Pellets

The University of Florida (UF) evaluated a composite fuel consisting of UO 2 powder mixed with diamond micro particles as a candidate as an accident-tolerant fuel (ATF). The research group had previous extensive experience researching with diamond micro particles as an addition to reactor coolant for improved plant thermal performance. The purpose of this research work was to utilize diamond micro particles to develop UO 2 -Diamond composite fuel pellets with significantly enhanced thermal properties, beyond that already being measured in the previous UF research projects of UO 2 – SiC and UO 2 – Carbon Nanotube fuel pins. UF is proving with the current research results that the addition of diamond micro particles to UO 2 may greatly enhanced the thermal conductivity of the UO 2 pellets producing an accident-tolerant fuel. The Beginning of life benefits have been proven and fuel samples are being irradiated in the ATR reactor to confirm that the thermal conductivity improvements are still present under irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nuclear Physics Research at Jefferson Lab

The Florida International University (FIU) experimental nuclear physics group consists of four to five faculty, four to eight graduate students, at times one postdoctoral scholar, and several undergraduate students. Our research is mainly conducted at Jefferson Lab's Continuous Electron Accelerator Beam Facility. We are studying the electroprodcution of strangeness and also the interaction of strange baryons, hyperons, with nuclear matter; the effects of two-photon exchange on nuclear form factor measurements; the short range correlations in nuclei; and the production of exotic mesons. Over the entire period of this project, members of the group have been leading the data acquisition and analysis efforts as co-spokespersons of 12 Jefferson Lab experiments, as well as contributed to the efforts of the broader JLab user community. This has resulted in the publication of over 300 papers in peer reviewed journals and conference proceedings. Twelve students received their Ph.D. and four their M.S. based on analysis of data collected during this project.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Phased Array Ultrasonic Examination of Reactor Coolant System (Carbon Steel-to-CASS) Dissimilar Metal Weld Mockup Specimen

In the summer of 2009, Pacific Northwest National Laboratory (PNNL) staff traveled to the Electric Power Research Institute (EPRI) NDE Center in Charlotte, North Carolina, to conduct phased-array ultrasonic testing on a large bore, reactor coolant pump nozzle-to-safe-end mockup. This mockup was fabricated by FlawTech, Inc. and the configuration originated from the Port St. Lucie nuclear power plant. These plants are Combustion Engineering-designed reactors. This mockup consists of a carbon steel elbow with stainless steel cladding joined to a cast austenitic stainless steel (CASS) safe-end with a dissimilar metal weld and is owned by Florida Power & Light. The objective of this study, and the data acquisition exercise held at the EPRI NDE Center, were focused on evaluating the capabilities of advanced, low-frequency phased-array ultrasonic testing (PA-UT) examination techniques for detection and characterization of implanted circumferential flaws and machined reflectors in a thick-section CASS dissimilar metal weld component. This work was limited to PA-UT assessments using 500 kHz and 800 kHz probes on circumferential flaws only, and evaluated detection and characterization of these flaws and machined reflectors from the CASS safe-end side only. All data were obtained using spatially encoded, manual scanning techniques. The effects of such factors as line-scan versus raster-scan examination approaches were evaluated, and PA-UT detection and characterization performance as a function of inspection frequency/wavelength, were also assessed. A comparative assessment of the data is provided, using length-sizing root-mean-square-error and position/localization results (flaw start/stop information) as the key criteria for flaw characterization performance. In addition, flaw signal-to-noise ratio was identified as the key criterion for detection performance.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High Resolution Model Development to Quantify the Impact of Icebergs on the Stability of the Atlantic Meridional Overturning Circulation

In the present-day North Atlantic Ocean, relatively warm and salty water moves northwards from the tropics to the high latitudes, sinks, and returns southward towards the equator as North Atlantic Deep Water, forming the so called Atlantic Meridional Overturning Circulation (AMOC). It has been found that the stability of the AMOC is non-linearly related to the freshwater budget of the North Atlantic. In this way, additional fresh water can be added to the ocean with little impact, until a tipping point is reached that causes the AMOC to suddenly weaken and the Northern Hemisphere to abruptly cool. A great deal of uncertainty still remains over the sensitivity of the AMOC to changes in freshwater discharge as a result of the unrealistic manner in which freshwater has historically been added to climate models. Frequently, freshwater is discharged in ocean models entirely as liquid water, but in reality a large fraction of freshwater entering the ocean is ice calving from marine glaciers (half for Antarctica and two-thirds for Greenland). To more accurately quantify AMOC sensitivity to past and future changes in freshwater input, this project developed a comprehensive iceberg model to more realistically simulate the interaction between the cryosphere and the oceans at high-latitudes. The iceberg model created is written in Fortran90 and designed to scale efficiently on High Performance Computing (HPC) clusters so that tens-of-thousands of icebergs can be simulated at any time. Experiments performed with our model showed that in the Pleistocene there would have been enormous floods of freshwater released into the North Atlantic that would have transported icebergs and meltwater along the entire east coast of the United States, as far south as Florida Keys. In addition, high-resolution, modern-day, model simulations showed that if the Greenland Ice Sheet continues to melt at its current rate then there will be a 6-fold increase in the number of icebergs drifting in the North Atlantic in the next 30 years, and that the strength of the AMOC could weaken by 3.5%.

54 ENVIRONMENTAL SCIENCES↗