Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CORROSIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Corrosion sensitivity of nickel-based Alloy Inconel 600 in pressurized water reactor water chemistry: Can KOH replace LiOH?

Lithium hydroxide (LiOH) has been used to balance water acidity against boric acid moderators in the primary water of Western pressurized water reactor (PWR) designs for decades. However, the demand and the cost of lithium-7 has grown significantly since 2015. Potassium hydroxide (KOH) has been identified as a suitable and cost-effective substitute for LiOH and has been used successfully in Russian PWR designs for more than 40 years. However, it is important to know if alloys and water conditions used in Western PWR’s (Alloy 600) are similarly compatible with KOH additions. This work is focused on the aqueous corrosion behaviors of Alloy 600 with LiOH versus KOH additions at normal operating concentrations and crevice water chemistry at simulated PWR primary water conditions. TEM was used to characterize the formed oxide through diffraction analysis; SIMS was used to probe the cation ingress into the material; Atom probe tomography was used to determine the 3D elemental distribution within the oxide/metal structures; finally electrochemical impedance spectroscopy was used to discuss the structure and corrosion resistance of the oxide films. These advanced characterization techniques complement the weight measurments which showed lower mass gain in KOH than LiOH crevice water due to less oxide formation. Overall, the use of KOH as a potential alternative to LiOH in PWR is discussed.

Alloy 600↗
DOE OSTI2022

Electrochemical noise studies on localized corrosion of Ni and Ni-20Cr in molten ZnCl 2

The electrochemical noise (ECN) technique was employed to study corrosion of two model systems, i.e. pure Ni and a binary Ni-20 wt%Cr (Ni20Cr) alloy in molten ZnCl 2 at 623 K. Here we measured ECN transients in current and open-circuit potential from two nominally identical Ni-Ni and Ni20Cr-Ni20Cr electrodes and one galvanic Ni-Ni20Cr electrode pair. The behavior of ECN is quite distinct among the three-electrode systems, and it is correlated with the various microscopic observations of micro- and nano-scale morphological features. Based on the ECN study coupled with the microstructural analysis, the origins of ECN in the molten salt environment as well as the mechanisms of localized corrosion in the three systems are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Corrosion of stainless steels in the riser during co-processing of bio-oils in a fluid catalytic cracking pilot plant

Co-processing of bio-oils with conventional petroleum-based feedstocks is an attractive initial option to make use of renewable biomass as a fuel source while leveraging existing refinery infrastructures. But, bio-oils and their processing intermediates have high concentrations of organic oxygenates, which, among their other negative qualities, can result in increased corrosion issues. A range of stainless steel alloys (409, 410, 304L, 316L, 317L, and 201) was exposed at the base of the riser in a fluid catalytic cracking pilot plant while co-processing vacuum gas oil with pine-derived pyrolysis bio-oils that had been catalytically hydrodeoxygenated to ~ 2 to 28% oxygen. We studied the processing using a catalyst temperature of 704 °C, a reaction exit temperature of 520 °C, and total co-processing run times of 57–75 h. External oxide scaling 5–30 μm thick and internal attack 1–5 μm deep were observed in these short-duration exposures. The greatest extent of internal attack was observed for co-processing with the least stabilized bio-oil, and more so for types 409, 410, 304L, 316L, 317L stainless steel than for type 201. Finally, the internal attack involved porous Cr-rich oxide formation, associated with local Ni-metal enrichment and S-rich nanoparticles, primarily containing Cr or Mn. Implications for alloy selection and corrosion are discussed.

09 BIOMASS FUELS↗
DOE OSTI2019

A space-time adaptive finite element method with exponential time integrator for the phase field model of pitting corrosion

In this paper we propose a space-time adaptive finite element method for the phase field model of pitting corrosion, which is a parabolic partial differential equation system consisting of a phase variable and a concentration variable. A major challenge in solving this phase field model is that the problem is very stiff, which makes the time step size extremely small for standard temporal discretizations. Another difficulty is that a high spatial resolution is required to capture the steep gradients within the diffused interface, which results in very large number of degrees of freedom for uniform meshes. To overcome the stiffness of this model, we combine the Rosenbrock–Euler exponential integrator with Crank–Nicolson scheme for the temporal discretization. Moreover, by exploiting the fact that the speed of the corroding interface decreases with time, we derive an adaptive time stepping formula. For the spatial approximation, we propose a simple and efficient strategy to generate adaptive meshes that reduces the computational cost significantly. Thus, the proposed method utilizes local adaptivity and mesh refinement for efficient simulation of the corrosive dissolution over long times in heterogeneous media with complex microstructures. We also present an extensive set of numerical experiments in both two and three dimensional spaces to demonstrate efficiency and robustness of the proposed method.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Network structure in alteration layer of boroaluminosilicate glass formed by aqueous corrosion

Exogenously-added LiCl has been shown to slightly accelerate the corrosion rate of a boroaluminosilicate glass called International Simple Glass (ISG) in aqueous solutions over forward- and residual-rate regimes, while KCl and CsCl impede. To understand the effect of exogenously added electrolytes on resulting hydrous species and the network structure of alteration layers, infrared spectroscopy was implemented. It was found that the fraction of molecular water relative to the surface-bound hydroxyl species is lower in the KCl and CsCl conditions compared to the LiCl and pure water conditions. An approximation for the spectral features of the thin surface films from an experimentally-obtained specular-reflectance infrared (SR-IR) spectrum was proposed; results indicate no significant difference in the Si-O bonding network of the alteration layers formed in the presence of exogenously added LiCl, KCl and CsCl. Furthermore, the observed change in corrosion rates might be linked to the relative abundance of molecular water species in the porous network, rather than the silicate bonding structure.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2014

Superior Corrosion Resistance Properties of TiN-Based Coatings on Zircaloy Tubes in Supercritical Water

Thin films of TiN and Ti0.35Al0.65N nanocomposite were deposited on polished Zircaloy-4 tubes. After exposure to supercritical water for 48 h, the coated tubes are remarkably intact, while the bare uncoated tube shows severe oxidation and breakaway corrosion. X-ray diffraction patterns, secondary electron images, backscattered electron images, and energy dispersive X-ray spectroscopy data from the tube surfaces and cross-sections show that a protective oxide, formed on the film surface, effectively prevents further oxidation and corrosion to the Zircaloy-4 tubes. This result demonstrates the effectiveness of thin film ceramics as protective coatings under extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Corrosion behavior of Fe–Cr–Si alloys in simulated PWR primary water environment

Fe–Cr–Si alloys are potential candidates as accident tolerant fuel (ATF) cladding, which could offer similar benefits as Fe–Cr–Al alloys. The corrosion and oxidation behaviors of three Fe–Cr–2Si alloys with various chromium content (12 wt. %, 16 wt. %, 20 wt. %) in simulated primary water chemistry of a pressurized water reactor (PWR) were investigated. Post-test characterization included weight change, scanning electron microscopy (SEM), and X-ray Photoelectron Spectroscopy (XPS). The results showed that Fe12Cr2Si had the worst corrosion/oxidation resistance among the three alloys, while Fe16Cr2Si and Fe20Cr2Si showed excellent oxidation resistance due to their thin, continuous, dense oxide layers grown in simulated PWR conditions. These results bring insight into the corrosion behavior of Fe–Cr–Si alloys with varying chromium content exposed to the primary water environment during normal operating conditions found in PWRs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effects of neutron and ionizing irradiation on the aqueous corrosion of SiC

Chemical vapor deposited (CVD) SiC and nuclear-grade SiC/SiC composite materials were exposed to light water reactor (LWR) conditions at the MIT Nuclear Reactor (MITR) here. Three sets of samples were exposed within flowing PWR-chemistry-coolant under either 1) neutron and ionizing irradiation with resulting radiolysis products, 2) radiolysis products without neutron flux, 3) loop coolant. Post-irradiation examination (PIE) exhibited an increase in corrosion from radiolysis products (particularly H 2 O 2 ), and potentially a further increase from radiation damage. For CVD SiC, regardless of exposure location, the in-situ observed corrosion rate was less than 1 µm per year, potentially within acceptable limits for LWR application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Hydrothermal corrosion of laser printed SiC fibers under extreme environment

We report SiC/SiC fiber composites are proposed cladding materials to improve the accident tolerance of commercial light water nuclear reactor fuel. To evaluate their viability, understanding the kinetics of corrosion under irradiation and high-temperature, high-pressure aqueous environment is critical. In the present work, the microstructure and mechanical properties of novel SiC fibers manufactured by Laser Chemical Vapor Deposition (LCVD) are introduced. The LCVD technology has control over microstructure and stoichiometry while allowing for high purity manufacturing, all key qualities needed in search of an optimum SiC fiber for nuclear energy applications. The isolated hydrothermal corrosion of commercially available carbon-rich Hi-Nicalon Type-S fibers is compared to the LCVD stoichiometric and LCVD silicon-rich fibers. Autoclave testing was carried out at 310°C and 14 MPa in the absence of irradiation. In a separate study, the effect of gamma irradiation on the fibers in the room-temperature environment was analyzed. It was observed from the experiments that the dissolution of the fibers was highly dependent on the stoichiometric ratio, fiber surface morphology and thermal pre-treatment of fibers. Contrary to previous findings, fiber dissolution was also visible under low-temperature gamma irradiation in aqueous environment with LCVD fibers showing lower dissolution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Corrosion behavior of a series of combinatorial physical vapor deposition coatings on SiC in a simulated boiling water reactor environment

Here, the simulated boiling water condition corrosion properties of multilayer and combinatorial physical vapor deposition metal coatings (Zr, Cr, and/or Ti) deposited on a SiC f -SiC composite were investigated. Various compositions within the ternary system were corroded to the most suitable composition preventing underlying SiC f -SiC from further attack. Mass measurements and visual observations were conducted to identify which coatings formed protective oxides and which coatings spalled. Transmission electron microscopy was conducted to observe the microstructure of the physical vapor deposition metal layer before and after corrosion as well as identify the oxide which were forming.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of corrosion layer composition and thermal pretreatment on the radiolytic generation of molecular hydrogen from aluminum alloys

To fully evaluate the feasibility of extending the dry storage of aluminum-clad spent nuclear fuel (ASNF) in helium-backfilled cannisters, the amount of radiation-induced molecular hydrogen (H 2 ) generated and the impact of absorbed radiation dose on the ASNF corrosion layer composition must be accurately assessed. Here, in this study, we report a slowing in the rate of radiolytic H 2 generation for pre-corroded AA1100 and AA6061 aluminum alloy coupons irradiated to up to 53 MGy of absorbed cobalt-60 gamma dose. By exploring a variety of thermal pretreatment conditions for AA6061 coupons, we find that the “steady-state” yield of H 2 depends more on the aluminum alloy used than on the treatments applied prior to dry storage. Scanning electron microscopy and positron annihilation lifetime spectroscopy techniques also provided evidence for gamma radiation-induced defects in the corrosion layers of the investigated aluminum alloy coupons for high absorbed doses (~50 MGy), the consequences of which on cladding integrity and H 2 generation should be explored in future works.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗
DOE OSTI2018

Crystallography of intergranular corrosion in sensitized austenitic stainless steel

Highlights: • Intergranular corrosion (IGC) in stainless steel was crystallographically discussed. • Grain boundaries (GBs) were classified based on the coincidence site lattice (CSL). • Influence of the Σ value on their IGC susceptibility had a wide range scatter. • IGC susceptibility was characterized by the Σ value and unit cell area of CSL GBs. - Abstract: This study deals with the susceptibility to intergranular corrosion (IGC) in type 304 austenitic stainless steel from a crystallographic viewpoint. An IGC test was conducted using oxalic acid and sensitized stainless steel, whose crystal orientation was analyzed by electron backscattered diffraction (EBSD). GBs were classified according to the misorientation of adjacent grains, and subclassified using the Σ value based on the coincidence site lattice (CSL) model. The width of corroded groove was measured for each GB category, and the effect of GB category on the susceptibility to IGC was examined. Then, the area of the unit cell of CSL boundaries was used to characterize the susceptibility to IGC of CSL boundaries. It was found that no IGC occurred in low-angle GBs with a misorientation of 15°, the width of corroded groove at each Σ boundary exhibited large scatter. The relationship between the width and unit cell area was characterized by a sigmoid curve, and the susceptibility to IGC was well described by the unit cell area.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure evolution during low-strain thermo-mechanical processing and its repercussion on intergranular corrosion in alloy 600H

Highlights: • GBE microstructure in alloy 600H is realized through the sole activation of SIBM. • Higher TRD size and lower fractal dimension are characteristics of GBE microstructure. • Partially/fully recrystallized specimen shows higher DOS than as-received condition. • GBE specimen shows remarkable resistance against percolation and grain dropping. • Extent of percolation is governed by residual strain and random HAGBs connectivity. - Abstract: The current investigation deals with the evolution of microstructures as a consequence of varying processing parameters viz. extent of deformation, annealing temperature and time during grain boundary engineering (GBE) type thermo-mechanical processing in alloy 600H. Furthermore, the influence of the various product microstructures (viz. partially recrystallized, fully recrystallized and GBE) on intergranular corrosion is evaluated and compared with the as-received condition. Detailed characterization of the as-processed specimens have revealed that lower extent of deformation (7.5%) followed by a longer annealing treatment (i.e. 60 min) at a higher temperature (1373 K) could lead to a GBE microstructure with a higher proportion of Σ3{sup n} boundaries (~72%) due to the predominant activation of multiple twinning. In contrast, the specimens associated with moderately higher extent of deformation (10% and 15%) have revealed the occurrence of static recrystallization. The GBE specimen has demonstrated an excellent resistance against percolation essentially due to its discontinuous random high angle boundaries (HAGBs) network. In contrast, the nucleation of the finer grains in the recrystallized specimens caused the regeneration of random HAGBs network (as substantiated by the fractal analysis) that leads to higher percolation and severe grain dropping. In spite of the similar grain boundary character distribution, the severity of corrosion is relatively lesser in the as-received condition than the completely recrystallized specimen owing to its coarse-grained microstructure that commendably retarded the diffusion of chromium from the grain interior to the boundary.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Air-stable, earth-abundant molten chlorides and corrosion-resistant containment for chemically-robust, high-temperature thermal energy storage for concentrated solar power

A dramatic reduction in man-made CO 2 emissions could be achieved if the cost of electricity generated from concentrated solar power (CSP) plants could become competitive with fossil-fuel-derived electricity. The solar heat-to-electricity conversion efficiency of CSP plants may be significantly increased (and the associated electricity cost decreased) by operating CSP turbines with inlet temperatures ≥750 °C instead of ≤550 °C, and by using thermal energy storage (TES) at ≥750 °C to allow for rapidly dispatchable and/or continuous electricity production. Unfortunately, earth-abundant MgCl 2 -KCl-based liquids currently being considered as low-cost media for large-scale, high-temperature TES are susceptible to oxidation in ambient air, with associated undesired changes in liquid composition and enhanced corrosion of metal alloys in pipes and tanks containing such liquids. In this paper, alternative high-temperature, earth-abundant molten chlorides that are resistant to oxidation in ambient air are identified via thermodynamic calculations. Here, the oxidation resistance, and corrosion-resistant containment, of such molten chlorides at 750 °C are then demonstrated. Such an air-tolerant strategy, involving chemically-robust, low-cost TES media paired with effective containment materials, provides a critical advance towards the higher-temperature operation of, and lower-cost electricity generation from, CSP plants.

14 SOLAR ENERGY↗
DOE OSTI2018

Nonlinear resonant ultrasound spectroscopy of stress corrosion cracking in stainless steel rods

Stainless steel containers are susceptible to stress corrosion cracking (SCC) under certain stress and corrosion conditions. Nonlinear ultrasonic techniques are very sensitive to the early presence of damage, more so than linear techniques. Nonlinear Resonant Ultrasound Spectroscopy (NRUS) is used here to measure a nonlinear shift in the resonance frequency due to a cumulative amount of SCC. Steel rods are immersed in a heated magnesium chloride solution and removed after different exposure times. NRUS measurements are conducted using the fundamental longitudinal mode of vibration. Rods exposed longer generally have a larger resonance frequency shift and are therefore more nonlinear. Thus NRUS might offer a means of detecting a cumulative SCC damage in a sample.

36 MATERIALS SCIENCE↗
DOE OSTI2024

How irradiation promotes intergranular stress corrosion crack initiation

Irradiation assisted stress corrosion cracking (IASCC) is a form of intergranular stress corrosion cracking that occurs in irradiated austenitic alloys. It requires an irradiated microstructure along with high temperature water and stress. The process is ubiquitous in that it occurs in a wide range of austenitic alloys and water chemistries, but only when the alloy is irradiated. Despite evidence of this degradation mode that dates back to the 1960s, the mechanism by which it occurs has remained elusive. Here, using high resolution electron backscattering detection to analyze local stress-strain states, high resolution transmission electron microscopy to identify grain boundary phases at crack tips, and decoupling the roles of stress and grain boundary oxidation, we are able to unfold the complexities of the phenomenon to reveal the mechanism by which IASCC occurs. The significance of the findings impacts the mechanical integrity of core components of both current and advanced nuclear reactor designs worldwide.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Amorphous and partially-amorphous metal coatings for corrosion resistance in molten chloride salt

In this study, amorphous metal coatings were developed to improve the corrosion resistance of structural alloys in molten salts for use as salt-facing materials in concentrating solar power (CSP) and molten salt reactor (MSR) applications. Three coatings were tested. One Fe-based, fully amorphous coating, and two Ni-based partially amorphous coatings. The candidate coatings were applied to samples made from Ni-based alloy 230, and exposed to KCl–MgCl 2 at 750 °C for 300 h in sealed Mo capsules. After exposure, uncoated alloy 230 samples were depleted in chromium near the surface, as measured by SEM-EDS. The attack had an average depth of 33 μm. Lastly, all three coatings performed well, showing no observable degradation during exposure, despite chromium contents between 20% and 40%. XRD and TEM measurements showed the coatings were fully crystallized after exposure, so the excellent corrosion resistance can likely be attributed to the recrystallized microstructure of the coatings.

14 SOLAR ENERGY↗
DOE OSTI2018

Extraordinary Corrosion Protection from Polymer–Clay Nanobrick Wall Thin Films

Metals across all industries demand anticorrosion surface treatments and drive a continual need for high-performing and low-cost coatings. Here we demonstrate polymer–clay nanocomposite thin films as a new class of transparent conformal barrier coatings for protection in corrosive atmospheres. Films assembled via layer-by-layer deposition, as thin as 90 nm, are shown to reduce copper corrosion rates by >1000× in an aggressive H 2 S atmosphere. Furthermore, these multilayer nanobrick wall coatings hold promise as high-performing anticorrosion treatment alternatives to costlier, more toxic, and less scalable thin films, such as graphene, hexavalent chromium, or atomic-layer-deposited metal oxides.

36 MATERIALS SCIENCE↗