Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Battery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Battery Relevant Cell Side Wall Rupture Characterization

The propensity for a cell design to experience can side wall rupture (SWR) during thermal runaway is highly influenced by how a battery design mechanically constrains its cells. Testing cells while unsupported has been found to yield false negative results that don't represent this risk in a battery configuration. This talk addresses how to verify the adequacy of battery design measures used to control SWR and how to get results relevant, accurate, and statistically defendable for a proposed battery design.

thermal runaway↗
NASA NTRSDate not supplied

Orion Power Transfer: Impacts of a Battery-on-Bus Power System Architecture

The Orion Multi-Purpose Crew Vehicle (MPCV) has the capability to transfer power to a co-manifested payload (CPL) during transit from low-Earth orbit to the lunar vicinity. This paper discusses a time-phased parametric power analysis to determine the Orion power transfer capability limit. Charge and discharge curves were generated for various power transfer conditions and measured against various minimum system voltage limits. The Orion electrical power system (EPS) utilizes an unregulated bus architecture, which has important implications when the system is operating under very high load demand conditions, such as during power transfer. This analysis highlights three important effects of this architecture. First, increasing load demand decreases the maximum state of charge (SOC) the batteries can reach when charging. Second, increasing load demand also decreases the allowable battery depth of discharge. These two together can significantly reduce the effective useable capacity of the batteries. Finally, low battery voltage decreases the power generation of the solar arrays. This can lead to significantly longer recharge times or even push the system out of energy balance. These effects have important implications for mission design and vehicle operations and must be accounted for when conducting sizing and design of an unregulated spacecraft EPS.

Electrical Power System↗
NASA NTRSDate not supplied

Material Property Estimation in Thin Battery Components Using Guided Wave Measurement, Experimental Dispersion Curve Extraction and Finite Element Modeling

At NASA, we are investigating nondestructive evaluation (NDE) and structural health monitoring (SHM) techniques to detect precursors of thermal runaway failure in lithium metal based lithium ion batteries (LIB). The approach is centered on computational simulation models to guide inspection and aid in interpretation of results. Since lithium metal LIBs have combinations of solid and fluid-filled porous materials, obtaining accurate material properties is both challenging and critical for successful simulation of battery inspection. To this end, we investigated a multi-verification approach for material characterization of thin battery components. First, a laser Doppler vibrometer (LDV) was used to measure guided wave fields in thin (microns-thick) battery components subject to broadband excitation. The time-space wavefield data was converted to frequency-wave number data to extract guided wave dispersion curves. A data visualization and post processing graphics user interface (GUI) was developed at NASA to aid the data exploration and analysis. Due to the thinness of the samples, low frequency-thickness-product plate wave approximations allowed for the calculation of closed-form solutions for material elastic property estimation. These approximations were then verified by calculating the Lamb wave solutions using the previously obtained material properties. Finally, the estimated elastic material properties were implemented in a COMSOL simulation model, and dispersion curves were extracted from simulation results. The dispersion curves and derived material properties were then compared to the analysis results from the experimental data. These comparisons informed on the accuracy of the measured material properties and helped demonstrate the accuracy of the finite element analysis (FEA) computational models. This assessment will prove vital when we start simulating more complex multi-layer components and poroelastic media. This paper gives a brief background of the problem space, outlines the workflow for data analysis and verification, shows results from the workflow, and gives an overview of future plans for simulation of lithium metal LIB inspection.

Peter Juarez↗
NASA NTRSDate not supplied

SIBatt-3D In-Space/On-Surface 3D Printing of Sodium Ion Batteries using ISRU Materials

Sustainable on-demand power solutions are an absolute necessity as humanity works to establish a permanent presence on the moon and make the journey to Mars. NASA’s SIBatt-3D Early Career Initiative project at MSFC is developing shape-conformable Sodium-Ion batteries that can be 3D printed in-space as needed during extended space missions. SIBatt-3D makes use of the unique advantages of 3D printing to create shape-conformable batteries with improved performance that reduce dead volume in devices and seeks to utilize materials found in Lunar/Martian regolith as feedstocks to provide sustainable power for surface operations on the Moon and Mars. SIBatt-3D’s batteries also have terrestrial implications such as improved battery safety and sustainability.

3D Printing↗
DOE OSTI2020

Embedded fiber optic cables for battery management

A battery includes a folded bicell battery stack with an embedded fiber optic cable and sensor. A cell casing encloses the bicell stack with at least one fiber optic cable is embedded within the battery. The fiber optic cable includes an internal portion disposed within the cell casing and having at least one optical sensor disposed thereon. An external portion of the fiber optic cable protrudes from the casing. A sealing gasket is disposed at least partially around the fiber optic cable and between the cell sealing edges at a point of entry of the fiber optic cable into the battery.

25 ENERGY STORAGE↗
DOE OSTI2021

Dendrite inhibiting electrolytes for metal-based batteries

A metal-based battery includes at least one metal electrode immersed within an electrolyte that includes: (1) an aprotic solvent; (2) a simple halogen containing material; and (3) optionally a metal salt that includes a complex halogen containing anion. The simple halogen containing material may include a metal halide salt that includes a metal cation selected from the group including but not limited to lithium and sodium metal cations. The metal halide salt may also include a halide anion selected from the group consisting of fluoride, chloride, bromide and iodide halide anions. The use of the metal halide salt within the metal-based battery provides enhanced cycling ability within the metal-based battery. Also contemplated are additional simple halogen containing material additives that may enhance cycling performance of a metal-based battery.

Archer, Lynden A.↗
DOE OSTI2021

Impact resistant battery enclosure systems

Battery enclosure arrangements for a vehicular battery system. The arrangements, capable of impact resistance include plurality of battery cells and a plurality of kinetic energy absorbing elements. The arrangements further include a frame configured to encase the plurality of the kinetic energy absorbing elements and the battery cells. In some arrangements the frame and/or the kinetic energy absorbing elements can be made of topologically interlocked materials.

Tsutsui, Waterloo↗
DOE OSTI2022

Next-Generation Cobalt-Free Cathodes – A Prospective Solution to the Battery Industry's Cobalt Problem*

Lithium-ion batteries are over-reliant on cobalt-containing cathodes. Current projections estimate hundreds of millions of electric vehicles (EVs) will be on the road by 2050, and this ever-growing demand threatens to deplete global cobalt reserves at an alarming rate. Moreover, cobalt supply-chain issues have significantly increased cobalt prices throughout the last decade. As such, energy storage research and development need to reduce reliance on cobalt to meet ever-growing demands for lithium-ion batteries. This chapter summarizes the science/technology gaps and potential of numerous cobalt-free Li-ion cathodes, including layered, spinel, olivine, and disordered rocksalt systems. Despite the promising performance of these Co-free cathodes, scale-up and manufacturing bottlenecks associated with these materials must also be addressed to enable widespread adoption in commercial batteries. Overall, this review broadly highlights the enormous promise of “zero-cobalt” Li-ion batteries to enable sustainable production of EVs in the coming decades.

Muralidharan, Nitin↗
DOE OSTI2022

Methods and system for a battery

Systems and methods for operating a redox flow battery system may include switching the redox flow battery system to an idle mode, wherein the idle mode includes operation of the redox flow battery system outside of a charging mode and outside of a discharge mode; in response to switching to the idle mode, repeatedly cycling operation of an electrolyte pump between an idling threshold flow rate less than a charging threshold flow rate and a deactivation threshold flow rate; and in response to switching to the charging mode, maintaining operation of the electrolyte pump at the charging threshold flow rate greater than the idling threshold flow rate. In this way, a responsiveness of the redox flow battery system to charging and discharging commands can be maintained while in idle, while reducing parasitic pumping losses due to pumping and heating, and reducing shunt current losses.

Song, Yang↗
DOE OSTI2022

Polybenzimidazole (PBI) membranes for redox flow batteries

Disclosed are redox flow battery membranes, redox flow batteries incorporating the membranes, and methods of forming the membranes. The membranes include a polybenzimidazole gel membrane that is capable of incorporating a high liquid content without loss of structure that is formed according to a process that includes in situ hydrolysis of a polyphosphoric acid solvent. The membranes are imbibed with a redox flow battery supporting electrolyte such as sulfuric acid and can operate at very high ionic conductivities of about 100 mS/cm or greater. Redox flow batteries incorporating the PBI-based membranes can operate at high current densities of about 100 mA/cm2 or greater.

Benicewicz, Brian C.↗
DOE OSTI2022

Redox-flow batteries employing oligomeric organic active materials and size-selective microporous polymer membranes

Intermittent energy sources, including solar and wind, require scalable, low-cost, multi-hour energy storage solutions to be effectively incorporated into the grid. Redox-flow batteries offer a solution, but suffer from rapid capacity fade and low Coulombic efficiency due to the high permeability of redox-active species across the battery's membrane. Here we show that active-species crossover can be arrested by scaling the membrane's pore size to molecular dimensions and in turn increasing the size of the active material to be above the membrane's pore-size exclusion limit. When oligomeric redox-active organic molecules were paired with microporous polymer membranes, the rate of active-material crossover was either completely blocked or slowed more than 9,000-fold compared to traditional separators at minimal cost to ionic conductivity. In the case of the latter, this corresponds to an absolute rate of ROM crossover of less than 3 μmol cm−2 day−1 (for a 1.0 M concentration gradient), which exceeds performance targets recently set forth by the battery industry. This strategy was generalizable to both high and low-potential ROMs in a variety of electrolytes, highlighting the importance of macromolecular design in implementing next-generation redox-flow batteries.

Helms, Brett A.↗
DOE OSTI2022

Detection of an internal short circuit in a battery

An electrical device comprises a battery cell; a pressure sensor for measuring swelling forces of the battery cell, optionally with voltage, temperature and current sensors, and a battery management system including a controller. The controller executes a program to: (i) determine a reference swelling force corresponding to a reference electrical signal received from the pressure sensor at an earlier reference time, (ii) determine a second swelling force corresponding to a second electrical signal received from the pressure sensor at a later second time, and (iii) determine whether a risk of internal short circuit of the battery cell exists by comparing a reference level of the reference electrical signal and a signal representative of the second electrical signal. When the signal representative of the second electrical signal exceeds the reference level of the reference electrical signal by a threshold amount, a risk of internal short circuit of the cell exists.

Stefanopoulou, Anna G.↗
DOE OSTI2022

In operando, non-invasive state-of-charge monitoring for redox flow batteries

This document describes techniques and systems for in operando, non-invasive SOC monitoring of redox flow batteries. The described techniques and systems allow for accurate, inexpensive, portable, and real-time methods to measure the SOC of redox flow batteries. System operators can monitor the SOC by measuring an acoustic attenuation coefficient of the electrolyte in the redox flow battery. The acoustic attenuation coefficient is measured using an ultrasonic transducer attached to a probing cell, which is connected to an electrolyte flow of a redox flow battery. The acoustic attenuation coefficient provides an accurate, real-time SOC measurement that is generally insensitive to varying operational temperatures of the electrolyte solution.

25 ENERGY STORAGE↗
DOE OSTI2022

Techniques for charging and/or discharging a battery using frequency modulation

Described herein are techniques that increase the charging and/or discharging rate of a rechargeable battery, at least in part, by using frequency modulated (FM) signals having a frequency in the megahertz (MHz) frequency range. In some embodiments, the MHz frequency range may include any frequency between 0.1 MHz and 1 gigahertz (GHz). In some embodiments, a battery charger described herein may be configured to generate and transmit, to a battery, an FM signal modulated over a frequency range during a period of time, the FM signal having a frequency of at least 0.5 MHz during at least a first portion of the period of time. In some embodiments, a method described herein includes transmitting an FM signal modulated over a frequency range during a period of time and having a frequency of at least 0.5 MHz during at least a first portion of the period of time to a battery.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Low permeability polybenzimidazole (PBI) gel membranes for redox flow batteries

Disclosed are redox flow battery membranes, redox flow batteries incorporating the membranes, and methods of forming the membranes. The membranes include a densified polybenzimidazole gel membrane that is capable of incorporating a high liquid content without loss of structure that is formed according to a process that includes in situ hydrolysis of a polyphosphoric acid solvent followed by densification of the gel membrane. The densified membranes are then imbibed with a redox flow battery supporting electrolyte such as sulfuric acid and can operate at very high ionic conductivities of about 50 mS/cm or greater and with low permeability of redox couple ions, e.g. vanadium ions, of about 10−7 cm2/s or less. Redox flow batteries incorporating the membranes can operate at current densities of about 50 mA/cm2 or greater.

Benicewicz, Brian C.↗
DOE OSTI2022

Lithium-sulfur battery with high sulfur loading

A lithium-sulfur battery cathode including conductive porous carbon particles vacuum infused with sulfur and a conductive collector substrate to which the sulfur infused porous carbon particles are deposited. The sulfur infused carbon particles are encapsulated by an encapsulation polymer, the encapsulation polymer having ionic conductivity, electronic conductivity, polysulfide affinity, or combinations thereof. A lithium-sulfur battery including the lithium-sulfur battery cathode, a lithium anode and an electrolyte disposed between the sulfur cathode and the lithium anode is also provided. Methods of producing the sulfur cathode for use in a lithium-sulfur battery by a hybrid vacuum-and-melt method are also provided.

Henslee, Brian E.↗
DOE OSTI2023

Thermal regulation of batteries

A battery thermal management system for an air vehicle includes a liquid heat exchange circuit. The system includes at least one battery in thermal communication with the liquid heat exchange circuit. The system includes a controller operatively connected to the liquid heat exchange circuit. The controller is configured and adapted to variably select whether heat will be rejected to the liquid heat exchange circuit. The system includes at least one heat exchanger positioned on the liquid heat exchange circuit. The at least one heat exchanger is a liquid-air heat exchanger or a liquid-liquid heat exchanger. A method for controlling a thermal management system for an air vehicle includes determining an expected temperature of at least one battery, and cooling the at least one battery with a cooling device if the expected temperature exceeds a pre-determined expected temperature threshold.

Rheaume, Jonathan↗