SEARCH · Engineering Papers

Results for “BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Transonic shock-induced dynamics of a flexible wing with a thick circular-arc airfoil

A simple flexible wing model with an 18-percent circular arc airfoil was constructed and tested in the Langley Transonic Dynamics Tunnel to investigate the dynamic characteristics that a wing might have under these conditions. In the region of shock-boundary layer oscillations, buffeting of the first bending mode was obtained. This mode was well separated in frequency from the shock boundary layer oscillations. A limit cycle oscillation was also measured in a 'third bending-like' mode, involving wing vertical bending and splitter plate motion, which was in the frequency range of the shock-boundary layer oscillations. Several model configurations were tested, and a few potential fixes were investigated.

Bennett, Robert M.↗

NASA NTRS1984

A modal model for SCOLE structural dynamics

Information on a modal model for the Spacecraft Control Laboratory (SCOLE) is given in viewgraph form. A partial differential equation model covering roll bending, pitch bending, torsion, shear forces, and bending moments is given.

Joshi, Suresh M.↗

NASA NTRS1992

Combined forced and free convection in a curved duct

The purpose of this study is to investigate the flow and heat transfer characteristics of a combined forced and free convection flow in a curved duct. Solutions are obtained by solving the low Mach number model of the Navier-Stokes equation using a control volume method. The finite-volume method was developed with the use of a predictor-corrector numerical scheme and some new variations of the classical projection method. Solutions indicated that the existence of a buoyancy force has changed the entire flow structure inside a curved duct. Reversed flow at both inner and outer bend is observed. For moderate Reynolds number, the upstream section of the duct was significantly influenced by the free convection processes. In general, heat transfer is strong at the inner bend of the beginning of the heated section and at the outer bend on the last half of the heated section. The maximum velocity location is strongly influenced by the combined effects of buoyancy and centrifugal forces. A strong buoyancy force can reduce the strength of the secondary flow where it plays an important role in mixing.

Yam, Clement G.↗

NASA NTRS1992

Power assist EVA glove development

Structural modeling of the EVA glove indicates that flexibility in the metacarpophalangeal (MCP) joint can be improved by selectively lowering the elasticity of the glove fabric. Two strategies are used to accomplish this. One method uses coil springs on the back of the glove to carry the tension in the glove skin due to pressurization. These springs carry the loads normally borne by the glove fabric, but are more easily deformed. An active system was also designed for the same purpose and uses gas filled bladders attached to the back of the EVA glove that change the dimensions of the back of the glove and allow the glove to bend at the MCP joint, thus providing greater flexibility at this joint. A threshold control scheme was devised to control the action of the joint actuators. Input to the controller was provided by thin resistive pressure sensors placed between the hand and the pressurized glove. The pressure sensors consist of a layer of polyester film that has a thin layer of ink screened on the surface. The resistivity of the ink is pressure dependent, so an extremely thin pressure sensor can be fabricated by covering the ink patch with another layer of polyester film and measuring the changing resistance of the ink with a bridge circuit. In order to sense the force between the hand and the glove at the MCP joint, a sensor was placed on the palmar face of the middle finger. The resultant signal was used by the controller to decide whether to fill or exhaust the bladder actuators on the back of the glove. The information from the sensor can also be used to evaluate the effectiveness of a given control scheme or glove design since the magnitude of the measured pressures gives some idea of the torque required to bend a glove finger at the MCP joint. Tests of this actuator, sensor, and control system were conducted in an 57.2 kPa glove box by performing a series of 90 degree finger bends with a glove without an MCP joint assembly, a glove with the coil spring assembly, and with the four fingered actuated glove. The tests of these three glove designs confirm the validity of the model.

Main, John A.↗

NASA NTRS1992

The effects of crushing surface roughness on the crushing characteristics of composite tubes

The effects of crushing-surface roughness on the energy-absorption capability of graphite and glass-epoxy composite tubes were investigated. Fifty different combinations of fiber, matrix, and specimen ply orientation were evaluated. Two different crushing surface roughnesses were used in this investigation. Crushing surface significantly influences the energy-absorption capability only of tubes that crush in the lamina bending crushing mode; tubes that crush in other modes are not influenced because their lamina bundles do not slide against the crushing surface. Those tubes that crush in the lamina bending mode can achieve higher, lower, or no change in energy-absorption capability as crushing surface roughness increases. If the fiber failure strain of tubes that crush in the lamina bending crushing mode exceeds the matrix failure strain then the energy-absorption capability increases as crushing surface roughness increases. However, if the matrix failure strain exceeds the fiber failure strain then the energy-absorption capability increases as crushing surface roughness decreases. Energy-absorption capability is uninfluenced by crushing surface roughness for tubes that have equal fiber and matrix failure strains.

Farley, Gary L.↗

NASA NTRS1993

Experimental evaluation of tailored chordwise deformable box beam and correlation with theory

This paper describes an experimental methodology based upon the use of a flexible sling support and load application system that has been created and utilized to evaluate a box beam which incorporates an elastic tailoring technology. The design technique used here for elastically tailoring the composite box beam structure is to produce exaggerated chordwise camber deformation of substantial magnitude to be of practical use in the new composite aircraft wings. The traditional methods such as a four-point bend test to apply constant bending moment with rigid fixtures inhibits the designed chordwise deformation from occurring and, hence, the need for the new test method. The experimental results for global camber and spanwise bending compliances correlate well with theoretical predictions based on a beam-like model.

Rehfield, Lawrence W.↗

NASA NTRS1992

Temporal averaging in a turbulent environment - Compensation for phase drifts in phase shifting interferometry

In an effort to improve the signal to noise in an interference experiment, we have developed a method to remove systematic phase drift between data sets acquired over long time intervals. Using this technique, it is possible to average repeatedly acquired phase measurements and improve the phase estimate without sacrificing spatial resolution. Results from tests using real-time phase stepping holographic interferometry applied to cantilever bending of a piezoelectric bimorph indicate that white noise has been reduced from 3 to less than 1 deg (lambda/360) by averaging 36 phase compensated data sets before object bending and 36 data sets after bending.

Ovryn, B.↗

NASA NTRS1943

Torsion of Flanged Members with Cross Sections Restrained Against Warping

The longitudinal stresses and the stiffness of flange members - I-beams, channels, and Z-bars - were investigated when these members were subjected to torque with constraint against cross-sectional warping. Measured angles of rotation agreed with corresponding calculated values in which the torsion bending factor of the cross section was involved; the agreement was better for the I-beam and the Z-bar than for the channel. Longitudinal stresses measured at the mid-span were found to agree with the calculated values that involved unit warping as well as the torsion-bending factors: the channel showed the greatest discrepancy between measured and calculated values. When commonly given expressions for rotations and maximum longitudinal stresses in a twisted I-beam were applied to the channel and to the Z-bar, values were obtained that were in reasonably good agreement with values obtained by the method of torsion-bending constant and unit warping.

Hill, H N↗

NASA NTRS1948

A unified theory of plastic buckling of columns and plates

On the basis of modern plasticity considerations, a unified theory of plastic buckling applicable to both columns and plates has been developed. For uniform compression, the theory shows that long columns which bend without appreciable twisting require the tangent modulus and that long flanges which twist without appreciable bending require the secant modulus. Structures that both bend and twist when they buckle require a modulus which is a combination of the secant modulus and the tangent modulus. (author)

PLATES - PLASTICITY↗

NASA NTRS1944

Aerodynamic Tests of a Full-scale TBF-1 Aileron Installation in the Langley 16-foot High-Speed Tunnel

The failure of wing panels on a number of TBF-1 and TBM-1 airplanes in flight has prompted several investigations of the possible causes of failure. This report describes tests in the Langley 16-foot high-speed tunnel to determine whether these failures could be attributed to changes in the aerodynamic characteristics of the ailerons at high speeds. The tests were made of a 12-foot-span section including the tip and aileron of the right wing of a TBF-1 airplane. Hinge moments, control-link stresses due to aerodynamic buffeting, and fabric-deflection photographs were obtained at true airspeeds ranging from 110 to 365 miles per hour. The aileron hinge-moment coefficients were found to vary only slightly with airspeed in spite of the large fabric deflections that developed as the speed was increased. An analysis of these results indicated that the resultant hinge moment of the ailerons as installed in the airplane would tend to restore the ailerons to their neutral position for all the high-speed flight conditions covered in the tests. Serious aerodynamic buffeting occurred at up aileron angles of -10 degrees or greater because of stalling of the sharp projecting lip of the Frise aileron. The peak stresses set up in the aileron control linkages in the buffeting condition were as high as three times the mean stress. During the hinge-moment investigation, flutter of the test installation occurred at airspeeds of about 150 miles per hour. This flutter condition was investigated in some detail and slow-motion pictures were made of the motion of the wing tip and aileron. The flutter was found to involve simultaneous normal bending and chordwise oscillation of the wing and flapping of the aileron. The aileron motion appeared to be coupled with this flutter condition and was investigated in some detail and slow-motion pictures were made of the motion of the wing tip and aileron. The flutter was found to involve simultaneous normal bending and chordwise oscillation of the wing and flapping of the aileron. The aileron motion appeared to be coupled with the motion of the wing through the mass unbalance of the aileron in the normal-to-chord plane due to location of the hinge line 2.17 inches below the center of gravity of the aileron. Flutter did not occur when the installation was stiffened to prevent chordwise motion or when the bending frequency of the aileron system was appreciably higher than that of the wing as in the complete airplane installation.

Becker, John V↗

NASA NTRS1948

A unified theory of plastic buckling of columns and plates

Stowell, Elbridge Z↗

NASA NTRS1927

Approximations for column effect in airplane wing spars

The significance attaching to "column effect" in airplane wing spars has been increasingly realized with the passage of time, but exact computations of the corrections to bending moment curves resulting from the existence of end loads are frequently omitted because of the additional labor involved in an analysis by rigorously correct methods. The present report represents an attempt to provide for approximate column effect corrections that can be graphically or otherwise expressed so as to be applied with a minimum of labor. Curves are plotted giving approximate values of the correction factors for single and two bay trusses of varying proportions and with various relationships between axial and lateral loads. It is further shown from an analysis of those curves that rough but useful approximations can be obtained from Perry's formula for corrected bending moment, with the assumed distance between points of inflection arbitrarily modified in accordance with rules given in the report. The discussion of general rules of variation of bending stress with axial load is accompanied by a study of the best distribution of the points of support along a spar for various conditions of loading.

Warner, Edward P↗

NASA NTRS1932

Resonance vibrations of aircraft propellers

On the basis of the consideration of various possible kinds of propeller vibrations, the resonance vibrations caused by unequal impacts of the propeller blades appear to be the most important. Their theoretical investigation is made by separate analysis of torsional and bending vibrations. This method is justified by the very great difference in the two natural frequencies of aircraft propeller blades. The calculated data are illustrated by practical examples. Thereby the observed vibration phenomenon in the given examples is explained by a bending resonance, for which the bending frequency of the propeller is equal to twice the revolution speed.

Liebers, Fritz↗

NASA NTRS1931

Flat sheet metal girders with very thin metal web. Part I : general theories and assumptions

The object of this report was to develop the structural method of sheet metal girders and should for that reason be considered solely from this standpoint. The ensuing methods were based on the assumption of the infinitely low stiffness in bending of the metal web. This simplifies the basis of calculations to such an extent that many questions of great practical importance can be examined which otherwise cannot be included in any analysis of the bending stiffness of the buckled plate. This report refers to such points as the safety in buckling of uprights to the effect of bending flexibility of spars, to spars not set parallel, etc.

Wagner, Herbert↗

NASA NTRS1994

Simple Creep Test For Ceramic Fibers

Simple bend-stress-relaxation test yields information on creep-related properties of polycrystalline ceramic fibers. Determination of these properties important part of efforts to develop ceramic composite materials that retain mechanical strength and resistance to creep at high temperatures. Present test measures effects of time, temperature, and applied strain on creep-related relaxation of bend stress in ceramic fiber of almost any diameter in almost any environment, without need for contact sensors. Degree of relaxation of bend stress determined from radii of curvature.

Dicarlo, James A.↗

NASA NTRS1993

Flexure and the role of inplane force around coronae on Venus

Large coronae on Venus, such as Artemis and Latona, are rimmed by conspicuous trenches and associated outer rises. Sandwell and Schubert have observed that these systems resemble terrestrial subduction zones in planform and have succeeded in fitting an elastic plate bending equation to the inferred flexural topography. However, the first zero crossing bending moments required are -2.5 x 10(exp 17) N for Artemis and -5.0 x 10(exp 16) N for Latona. Since these moments are similar in magnitude to those of subducting slabs on Earth, a rollback subduction mechanism was proposed to explain the flexure around the largest coronae, although a differential thermal subsidence model is sufficient to account for the topography around some coronae. The purpose is to investigate the effect of inplane force as a possible alternative to large applied moments in producing flexure at Artemis and Latona. The close correlation of gravity to topography on Venus implies the absence of a low viscosity zone and the strong coupling of the lithosphere to mantle convection. If coronae are the surface manifestations of mantle plumes, they may be the sites of active convective stress coupling. As the upwelling reaches the lithosphere, it spreads radially outward, inducing shear tractions on the base of the plate. In addition, the hot, expanding corona may load the surrounding plate horizonally. Both the basal shear stresses and radial loading can be treated as an equivalent compressive inplane force in the mechanical lithosphere, which contributes to the bending of the outlying plate. Using a model that relates inplane force to the measured gravity anomalies, a rough value of the inplane force at Artemis was calculated. Recent Pioneer Venus spherical harmonic gravity models indicate a geoid anomaly of about 75 m over Artemis, which corresponds to an estimated inplane force on the order of -1x10(exp 13) N/m. The gravity model is unable to resolve Latona, but an inplane force of similar dimensions is assumed. The maximum possible inplane force based on the expected rheology can be constrained by using the approximate 5 K/km thermal gradient inferred from the best fit 30 km elastic plate at Artemis and Latona. For a dry olivine flow law in the upper mantle, the compressional load limit of the 60 km thick mechanical lithosphere is -4 x 10(exp 13) N/m. This value is equivalent to a load of -8 x 10(exp 13) N/m on a 30 km thick elastic plate.

Brown, C. David↗

NASA NTRS1993

Foil bearings

The rolling element bearings (REB's) which support many turbomachinery rotors offer high load capacity, low power requirements, and durability. Two disadvantages of REB's are: (1) rolling or sliding contact within the bearing has life-limiting consequences; and (2) REB's provide essentially no damping. The REB's in the Space Shuttle Main Engine (SSME) turbopumps must sustain high static and dynamic loads, at high speeds, with a cryogenic fluid as lubricant and coolant. The pump end ball bearings limit the life of the SSME high pressure oxygen turbopump (HPOTP). Compliant foil bearing (CFB) manufacturers have proposed replacing turbopump REB's with CFB's CFB's work well in aircraft air cycle machines, auxiliary power units, and refrigeration compressors. In a CFB, the rotor only contracts the foil support structure during start up and shut down. CFB damping is higher than REB damping. However, the load capacity of the CFB is low, compared to a REB. Furthermore, little stiffness and damping data exists for the CFB. A rotordynamic analysis for turbomachinery critical speeds and stability requires the input of bearing stiffness and damping coefficients. The two basic types of CFB are the tension-dominated bearing and the bending-dominated bearing. Many investigators have analyzed and measured characteristics of tension-dominated foil bearings, which are applied principally in magnetic tape recording. The bending-dominated CFB is used more in rotating machinery. This report describes the first phase of a structural analysis of a bending-dominated, multileaf CFB. A brief discussion of CFB literature is followed by a description and results of the present analysis.

Elrod, David A.↗

NASA NTRS1994

Deflections of anisotropic sandwich beams with variable face sheets and core thicknesses

A sandwich construction consists of a low-density core material with high strength face sheets bounded to the top and bottom surfaces. The construction has been widely used in the aerospace and marine industries due to its outstanding characteristics such as noise absorption, weight minimization, heat insulation, and better bending stiffness. In sandwich structures used in high-performance aircraft, the face sheets are often made of fiber-reinforced composite materials and the core is made of honeycomb. The structures may also have variable thickness so as to satisfy aerodynamic requirements. In the stress analysis, the constant-thickness face sheets are usually considered as membrane and the core is assumed to be inextensible but deformable in the thickness direction. The static behavior of variable-thickness, isotropic and homogeneous sandwich beams was successfully studied by employing a constant-thickness theory but allowing stiffnesses to vary in accordance with local thickness variations. It has been recently found in a refined theory that the analyses based on the constant thickness theory locally can lead to significant errors in structural responses if the sandwich beam is thickness-tapered and the cores are deformable in transverse shear. The errors arise mainly from two factors: (1) the transverse shear components of the membrane forces in the face sheets alter the transverse shears carried by the core; and (2) the face-sheet membrane strains arise from transverse shear deformation of the core. In practice the variable thickness may not only exist in core but also in face sheets. The thickness-variations may even be a type of step function. In this case the transverse shear stress in the face sheets and bending stress in the core should be taken into account in the refined theory mentioned. In the present study, energy principles are employed in deriving governing equations for general bending of anisotropic sandwich beams with variable thickness in both face sheets and cores. Solutions to these equations are based on a finite difference scheme. As an example in application, a simply supported thickness-tapered sandwich beam subject to a concentrated load at its center is considered. Let W' be the maximum deflection of the beam in which face sheets are considered as membrane, while W'' is that based on using the modified refined theory. It is found that W' is always larger than W'', however, the magnitude of (W'- W'') appears to be insensitive to the change of the taper of the beam.

Lu, Chu-Ho↗