Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additively Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Solidification dynamics in metal additive manufacturing: analysis of model assumptions

Solidification characteristics in the meltpool drive the process-microstructure relationship which helps dictate the material properties of as-built parts in additive manufacturing; therefore, being able to accurately and quickly simulate the size, shape, and solidification characteristics in the melt pool is of great interest to the field. In this study, we investigate various important physical phenomena (dynamic material properties, fluid-flow, radiation and vaporization) which can either be included or neglected in a continuum finite volume model (FVM) and their effect on the solidification conditions. Additionally, since the simplest form of such a model (conduction only) has an analytic solution which is much faster, its viability is also considered. Since the inclusion of some of these physical phenomena will inherently change the net energy input as well as the amount of energy needed to achieve melting of a control volume, each set of included phenomena had an effective absorption efficiency which was calibrated to closely match the dimensions of the melt pool to that of the ground truth data. The ground truth data for this study was defined to be the output of the FVM which included all the physical phenomena (OF). This study then goes on to compare the effects on solidification conditions each of these calibrated models has. It was found that most of the change in solidification conditions comes from the inclusion of latent heat. A posterior correlation factor (PCF) is then introduced to enable an analytic model to predict similar solidification conditions to OF model.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An additively manufactured AlCuMnZr alloy microstructure and tensile mechanical properties

In this study, selective laser melting (SLM) was used to fabricate an AlCuMnZr alloy. The microstructural features that resulted from additive manufacturing (AM) were significantly refined compared to the corresponding cast alloy features. A combination of fine equiaxed and columnar grains along with in-situ formation of θ' precipitates during AM leads to enhanced yield strength (up to 300°C) in the as-fabricated AM alloy. The refinement of brittle intermetallics and a bimodal grain size distribution leads to improved tensile elongation in the AM alloy. The results illustrate the microstructural advantages that can result from additive processing over conventionally processed microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the high-temperature stability of the Al 8 Cu 3 Ce intermetallic in an additively manufactured Al-Cu-Ce-Zr alloy

High-temperature resistant eutectic Al alloys are crucial materials for lightweight and energy efficient design in the automotive and aviation industries. Additive manufacturing offers a pathway to refine eutectic microstructures and develop novel alloys with superior high-temperature strength. High-volume fraction intermetallic Al-Cu-Ce alloys have been developed to deliver high-temperature strength in combination with reduced hot-tearing susceptibility. Zr is added to provide additional strengthening via nanoscale Al 3 Zr precipitation, and to stabilize and avoid coarsening of the Al 8 Cu 3 Ce phase. However, the detailed interaction between Zr and Al 8 Cu 3 Ce remains unexplored. In this work, we show with synchrotron X-ray diffraction that laser powder bed fusion fabricated Al-Cu-Ce and Al-Cu-Ce-Zr alloys contain predominantly the Al 8 Cu 3 Ce intermetallic in the as-fabricated condition. Heat treatment of the Al-Cu-Ce alloy results in the Al 8 Cu 3 Ce → Al 8 Cu 4 Ce phase transformation. In the Al-Cu-Ce-Zr alloy, minor fractions of (Al,Cu,Si) 4 Ce and Al 2 Cu-θ are found in the as-fabricated condition, while Al 8 Cu 3 Ce remains stable during heat treatment. Atom probe microscopy quantifies intermetallic stoichiometries and reveals how Zr is enriched at the Al-matrix/Al 8 Cu 3 Ce interface acting as a diffusion barrier against solute exchange. Calibrated thermodynamic modeling underpins this as a kinetic effect. Here, a qualitative microstructural model summarizes, how Zr stabilizes Al 8 Cu 3 Ce against phase transformations and coarsening.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Development of an Additively Manufactured Turbine Blade Tuned Mass Absorber

An innovative concept using a tuned mass absorber for resonant response reduction of turbine blades that is integrally fabricated into the blades using additive manufactured has been developed. Avoiding high resonant response and resulting high cycle fatigue failure is a major concern of the $100B worldwide turbine industry, which encompasses power generation, jet engines and rocket engine turbomachinery. Blade failure is potentially catastrophic, and although preventative measures using dampers do exist, these solutions are extremely expensive to develop and are not always effective. In addition, many of the existing techniques do not work for newer integrally bladed disks (or blisks), where there is no inherent damping in the assembly. The proposed concept, in which a tuned mass absorber re-arranges the structural dynamics and moves energy from the blade to the absorber, is designed specifically for blisks, and is intentionally linear, enabling accurate response prediction during design. Single blade prototypes have been analyzed, fabricated, and tested, and different absorber concepts have shown a reduction in response of up to 60%. After an extensive commercialization and prior art search, MSFC determined the innovation merited the generation and submission of a patent application in August ’21. Funding is now being sought to fabricate a 20-bladed blisk which would be spun at operational speeds with substantially higher and more realistic pressure loads in a special spin facility. Successful completion of this program would raise the TRL from 3/4 to 6/7, significantly improving the viability for adoption of the concept not only in rocket engines but other industrial applications as well.

Turbine Blades↗
DOE OSTI2022

Mechanical Behavior of Additively Manufactured Molybdenum and Fabrication of Microtextured Composites

Refractory metals are a class of high-melting-temperature materials suitable for use in extreme environment applications. Interestingly, during additive manufacturing many pure refractory metals exhibit a switch from (001) to (111) build direction fiber preference with increasing surface energy density. Here we exploit this solidification physics to fabricate material with “mesoscale composite” engineered structures consisting of features with contrasting (001) and (111) build direction microtextures. Separately, elevated temperature tensile testing of EBM fabricated material with a randomized distribution of mixed (001)/(111)-fiber grains is shown to exhibit excellent properties. These results are utilized to build a crystal plasticity model for evaluating the local inelastic response of the composite mesoscale structures. Analysis of printed microstructures and microstructure-scale simulations indicate that both macro-scale and localized material behavior may be tailored. This strategy can be potentially used to synthesize materials with optimized performance for high-temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structure-Property Relationships of Additively Manufactured Ni-Nb Alloys [Slides]

In this work, scratch and nanoindentation testing was used to determine hardness, fracture toughness, strain rate sensitivity, and activation volumes on additively manufactured graded and uniform Ni-Nb bulk specimens. Characterization showed the presence of a two phase system consisting of Ni 3 Nb and Ni 6 Nb 7 intermetallics. Intermetallics were multimodal in nature, having grain and cell sizes spanning from a few nanometers to 10s of micrometers. The unique microstructure resulted in impressively high hardness, up to 20 GPa in the case of the compositionally graded sample. AM methods with surface deformation techniques are a useful way to rapidly probe material properties and alloy composition space.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structure-Property Relationships of Additively Manufactured Ni-Nb Alloys [Slides]

In this work, scratch and nanoindentation testing was used to determine hardness, fracture toughness, strain rate sensitivity, and activation volumes on additively manufactured graded and uniform Ni-Nb bulk specimens. Characterization showed the presence of a two phase system consisting of Ni 3 Nb and Ni 6 Nb 7 intermetallics. Intermetallics were multimodal in nature, having grain and cell sizes spanning from a few nanometers to 10s of micrometers. The unique microstructure resulted in impressively high hardness, up to 20 GPa in the case of the compositionally graded sample. AM methods with surface deformation techniques are a useful way to rapidly probe material properties and alloy composition space.

36 MATERIALS SCIENCE↗
DOE OSTI2022

316L Stainless Steel Wire Arc Additive Manufacturing and Characterization for Potential SNF Canister Production

In this paper, 316L stainless steel (316L SS) straight walls, curved walls, and vessels were printed by wire arc additive manufacturing (WAAM) using the 316L SS welding wire, to demonstrate the feasibility of spent nuclear fuel (SNF) canisters using this advanced manufacturing technique. Helium leak test with leak tight criteria of 1 × 10-7 ref-cc/s were performed on printed vessels with various wall thickness, and testing pressures were from 0.345 MPa (50 psi) to 1.724 MPa (250 psi). Printed wall microstructures were characterized using optical microscopy (OM) and scanning electron microscopy (SEM). Tensile specimens were machined out from printed walls along the length, height, and thickness directions, respectively, and tested at different temperature conditions, room temperature, 80 °C, 150 °C and 250 °C, respectively. Results showed t hat, all five WAAM-printed canisters with different thickness passed the helium leaktight criteria of radioactive materials containers by the ANSI N14.5; Dispersed micrometer-level size inclusions/voids were observed at printed wall cross sections, dendritic microstructures were found with grain size variation through the welding torch shifting direction, and very small amount of δ-ferrite and σ-phase were also observed in those cross sections; The printed walls were ductile, all tensile specimens broke with large plastic deformation/elongation and without brittle failure, and printed specimens yield strengths and tensile strengths under room temperature and 80 °C conditions are higher than minimum values of 316L SS for pressure vessels and for general applications at room temperature required by the ASTM standard, respectively.

Tang, Wei↗
DOE OSTI2024

Method for producing neutron collimators using additive manufacturing

Collimators and other components for use in neutron scattering experiments or to provide neutron shielding in nuclear reactors or accelerator based neutron sources are produced by additive manufacturing from neutron absorbing material, such as boron carbide (B4C) or isotopically enriched boron carbide (10B).

Anderson, David C.↗
DOE OSTI2026

Process-driven roadmap for depositing super duplex stainless steel via wire Arc additive manufacturing

Here, this study systematically investigates the effects of shielding gas, bead spacing, weld mode, and travel speed on the phase balance, porosity, and hardness of wire arc additively manufactured (WAAM) super duplex stainless steel (ER2594). Robotic WAAM was employed to fabricate multilayer walls under systematically varied process conditions, followed by phase transformation simulations, X-ray computed tomography (XCT), electron backscatter diffraction (EBSD), and microhardness evaluation. Thermodynamic simulations predicted rapid cooling of AM process can suppress the potential formation of deleterious precipitates which was later validated via cross-sectional microstructure analyses of printed samples. XCT revealed porosity levels below 0.2% for all deposits, with reduced travel speed significantly lowering defect volume. Microstructural analyses revealed the evolution of various austenite precipitates, including grain boundary austenite (GBA), Widmanstätten austenite (WA), and intergranular austenite (IGA), sequentially upon cooling of the ferrite phase. Among all process parameters, weld transfer mode exhibited the strongest influence on phase balance; pulsed mode promoted higher ferrite retention (~ 36%) compared to RapidX mode. No consistent relationship between stabilized phase fraction and captured microhardness was observed. This work provides critical insights for optimizing WAAM parameters to control phase balance and mechanical performance, which is essential for producing high-integrity super duplex stainless-steel components for nuclear and marine applications.

Grain orientation↗
DOE OSTI2024

Effects of size, geometry, and testing temperature on additively manufactured Ti-6Al-4V titanium alloy

This article presents a comprehensive study concerning size and geometry effect on the ambient and high-temperature mechanical behavior of additively manufactured laser powder bed fusion Ti-6Al-4V alloy. Key mechanical property metrics are presented, including strain hardening rate, yield strength, and Young’s modulus as a function of thickness and testing temperature (ambient, 250 °C, and 450 °C). Here, the effect of specimen size on manufacturing-induced microstructural feature formation is demonstrated and discussed. A detailed analysis regarding Young’s modulus, yield strength, and strain hardening rate variation at elevated temperatures is also presented. Size effect and temperature-sensitive deformation mechanisms are linked to the underlying microstructural deformation mechanisms activated at respective temperatures. Counter-intuitively, this study determined that irrespective of the geometry, strain hardening rates increased as temperature increased. An in-depth microstructural examination is presented to explain the stated observation. The texture of Interrupted tensile test samples examined for ambient, 250 °C, and 450 °C post-yield was observed to be unchanged, indicating the strain hardening behavior was not texture dependent. Schmid factor analysis, coupled with experimental findings from previous work, was implemented to generate a hypothesis. This hypothesis suggests that the drop in critical resolved shear stress for basal and pyramidal slip systems, as temperature increases, paired with the high dislocation density of laser powder bed fusion Ti-6Al-4V, leads to dislocation entanglement and results in increased strain hardening at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Performance Testing of Additively Manufactured 316L Stainless Steel in Light Water Reactor Environment

This report summarizes research activities conducted at Argonne National Laboratory in support of the development, qualification and certification of additively manufactured (AM) metallic components for the long-term sustainability of light water reactors. In this program, AM 316L stainless steel (SS) has been evaluated in light water reactor (LWR) environments for their fatigue, environmentally assisted fatigue, and stress corrosion cracking performances on specimens in as-printed condition, aiming for facilitating the regulatory acceptance and ultimately adoption of AM components in aging LWRs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2024

Additively Manufactured Plastic Plasma Spectrometer

We report results in development and testing of a low resource top hat electrostatic analyzer (ESA) for space plasma measurements. This device has been additively manufactured (3D-printed) using fused deposition modeling. The classic top hat design is composed of four plastic pieces, without any surface coatings. The three conducting electrodes are printed from carbon nanotube infused polyether ether ketone (CNT-PEEK). The fourth piece, an insulating electrode support, uses pure PEEK. This ESA is designed to detect electrons in space from 10eV up to 30 keV. We demonstrate that the printed CNT-PEEK is sufficiently electrically conductive to support the fast high voltage slewing often required for high time resolution measurements. The plastic ESA has been successfully vibrated beyond standard pre-flight levels, tested under keV electron beam illumination over a wide range of temperatures, and tested under UV illumination, simulating the solar Ly-α flux. In comparison with an identical machined aluminum ESA, our CNT-PEEK ESA provides nominal energy/angle band passes, closely matching simulation. These band passes imply minimal impact from surface charging at beam energies of 2-3 keV, although more investigation is needed. We also find that the CNT-PEEK ESA provides far superior out-of-band electron rejection and UV photon rejection compared to the machined aluminum ESA. We do not detect any problems with trapped gases or outgassing. This development offers potential for significant mass savings, implementation of otherwise unattainable geometric configurations, and dramatic simplification in manufacturing and assembly processes required for development of space plasma instruments.

Quetzal Larrick↗
DOE OSTI2022

Creep behavior of $\gamma$-TiAl fabricated via electron beam additive manufacturing

$\gamma$-TiAl is a desirable structural engineering alloy with excellent high temperature specific strength. This material system has been shown to be processable at industrial scales via additive manufacturing. In this work we investigate the microstructure and properties of Ti48Al2Cr2Nb fabricated via electron beam melting. No significant anisotropy was observed from during creep testing under the considered conditions. Creep deformation resistance and rupture strength are comparable to material synthesized via traditional routes.

Fernandez-Zelaia, Patxi↗
DOE OSTI2024

Additive manufacturing of defect-free TiZrNbTa refractory high-entropy alloy with enhanced elastic isotropy via in-situ alloying of elemental powders

Laser powder-bed fusion (L-PBF) additive manufacturing presents ample opportunities to produce net-shape parts. The complex laser-powder interactions result in high cooling rates that often lead to unique microstructures and excellent mechanical properties. Refractory high-entropy alloys show great potential for high-temperature applications but are notoriously difficult to process by additive processes due to their sensitivity to cracking and defects, such as un-melted powders and keyholes. Here, we present a method based on a normalized model-based processing diagram to achieve a nearly defect-free TiZrNbTa alloy via in-situ alloying of elemental powders during L-PBF. Compared to its as-cast counterpart, the as-printed TiZrNbTa exhibits comparable mechanical properties but with enhanced elastic isotropy. This method has good potential for other refractory alloy systems based on in-situ alloying of elemental powders, thereby creating new opportunities to rapidly expand the collection of processable refractory materials via L-PBF.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling Nondestructive Defect Detection in Additively Manufactured Metallic Structures for Nuclear Applications

The future of quickly, economically produced metallic nuclear reactor parts with minimal supply-chain dependence lies in Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM): a 3D printing method involving laser melting and net shaping stainless steel and Inconel metallic powder into a solid structure. However, intrinsic features in LPBF frequently leads to the formation of materials defects, such as pores, within 3D printed structures. As safe long-term use in energy applications requires knowledge of all relevant defects before deployment in a reactor, we must develop methods for nondestructive detection of these defects. We are investigating Pulsed Thermal Tomography (PTT), which is a non-contact nondestructive imaging method scalable to arbitrary structure size. Thermal tomography (TT) is a computational method for 3D spatial reconstruction of material thermal effusivity from flash or pulsed thermography temperature data cube. Thermography data cube consists of 2D surface temperature measurements at different times. The objective of the present work is to investigate limits on defect detection in AM metallic structures with PTT. To this effect, we modeled PTT with COMSOL heat transfer computer simulations. We developed a layered media COMSOL simulation consisting of a Stainless Steel 316 (SS316) plate with an internal layer of un-sintered SS316 powder. Thermophysical properties of the powder layer were modeled with equivalent volume mixing model. To account for partial sintering at the boundary of the defect, the transition between solid and powder layers was modeled as a Gaussian. Using data from COMSOL simulations, we reconstructed depth-dependent thermal effusivity, which allowed defect visibility estimation. A series of parametric studies determined that at 1mm depth, 50µm is the smallest detectable defect. In addition, classification of the defects which can lead to early fatigue of the metallic structure in a reactor is briefly discussed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Additive manufacturing of multiscale NiFeMn multi-principal element alloys with tailored composition

Nanostructured multi-principal element alloys (MPEAs) have been explored as next-generation engineering materials due to unique mechanical and functional properties which have significant advantages over traditional dilute alloys. However, the practical applications of nanostructured MPEAs are still limited due to the lack of scalable processing approaches to prepare a large quantity of nanostructured MPEAs, as well as lack of an efficient pathway for high-throughput discovery of better functional nanostructured MPEAs within their vast compositional space. Here we tackle these challenges by presenting an integrated approach by combining direct-ink-writing-based additive manufacturing, solid-state sintering, and chemical dealloying to manufacture hierarchically porous MPEAs. The hierarchical structure is comprised of macro- and micro-scale pores introduced via extrusion printing and polymer decomposition during sintering, as well as nanoscale pores formed via chemical dealloying. The macro- and micro-scale pores allow efficient dealloying of a large mass of material as the diffusion length that the corroding medium must penetrate remains at the scale of the ligaments formed after sintering (∼10 μm), despite the large volume of the 3D-printed samples. In addition, this integrated approach enables versatile control of the alloy composition via precisely tuning the ratio of elemental powders in the starting ink, thus offering a pathway for high-throughput discovery of novel functional MPEAs. As a case study, multiscale macro/micro/nanoporous NiFeMn MPEAs with three different compositions were investigated as catalysts to reduce the overpotential of oxygen evolution reaction (OER), where NiFeMn-based electrocatalysts display composition-dependent performance such that the overpotential measured at a current of 0.5 A g −1 for OER increases in the order of Ni 58 Fe 29 Mn 13 ⩽ Ni 64 Fe 26 Mn 10 < Ni 76 Fe 18 Mn 6 . This introduced manufacturing process offers new opportunities for scalable fabrication and rapid screening of nanostructured multi-component complex alloys.

36 MATERIALS SCIENCE↗