Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

An aerodynamic model for one and two degree of freedom wing rock of slender delta wings

The unsteady aerodynamic effects due to the separated flow around slender delta wings in motion were analyzed. By combining the unsteady flow field solution with the rigid body Euler equations of motion, self-induced wing rock motion is simulated. The aerodynamic model successfully captures the qualitative characteristics of wing rock observed in experiments. For the one degree of freedom in roll case, the model is used to look into the mechanisms of wing rock and to investigate the effects of various parameters, like angle of attack, yaw angle, displacement of the separation point, and wing inertia. To investigate the roll and yaw coupling for the delta wing, an additional degree of freedom is added. However, no limit cycle was observed in the two degree of freedom case. Nonetheless, the model can be used to apply various control laws to actively control wing rock using, for example, the displacement of the leading edge vortex separation point by inboard span wise blowing.

Hong, John↗

Unstructured mesh algorithms for aerodynamic calculations

The use of unstructured mesh techniques for solving complex aerodynamic flows is discussed. The principle advantages of unstructured mesh strategies, as they relate to complex geometries, adaptive meshing capabilities, and parallel processing are emphasized. The various aspects required for the efficient and accurate solution of aerodynamic flows are addressed. These include mesh generation, mesh adaptivity, solution algorithms, convergence acceleration, and turbulence modeling. Computations of viscous turbulent two-dimensional flows and inviscid three-dimensional flows about complex configurations are demonstrated. Remaining obstacles and directions for future research are also outlined.

Mavriplis, D. J.↗

Structural and aerodynamic considerations for an oblique all-wing aircraft

A key design issue for the Oblique All-Wing aircraft is the packaging of the payload compartment, the fuel tanks, and the other internal components within the airfoil. The internal arrangement of such vehicles is strongly coupled to the exterior vehicle geometry. For example, the height requirements of a passenger cabin directly influence the aircraft thickness and span. As a result, the internal arrangement strongly affects aerodynamic performance and structural weight. Configuration criteria are defined and/or discussed, and a baseline aircraft is developed. Also, some of the major tradeoffs that affect structural weight and aerodynamic performance are presented.

Waters, M. H.↗

Taking the measure of aerodynamic testing

A review is presented of the major challenges for aerodynamic measurement created by advanced aircraft systems that range from turbulence modeling to scramjet engines. Three diverse examples typically challenge current capabilities: modeling of compressible turbulence, validation of complex 3D flow predictions, and thermochemical characterization of chemically active high-enthalpy flows. Various techniques being explored and under development to realize the aerodynamic measurements required are discussed.

Erbland, Peter J.↗

A new technique for aerodynamic noise calculation

A novel method for the numerical analysis of aerodynamic noise generation is presented. The method involves first solving for the time-dependent incompressible flow for the given geometry. This fully nonlinear method that is tailored to extract the relevant acoustic fluctuations seems to be an efficient approach to the numerical analysis of aerodynamic noise generation.

Hardin, J. C.↗

Variable-complexity aerodynamic-structural design of a high-speed civil transport wing

A variable-complexity strategy of combining simple and detailed analysis methods is presented for the design optimization of a high-speed civil transport (HSCT) wing. Two sets of results are shown: the aerodynamic design of the wing using algebraic weight equations for structural considerations, and optimization results of the internal wing structure for a fixed wing configuration. We show example results indicating that using simple analysis methods alone for the calculation of a critical constraint can allow an optimizer to exploit weaknesses in the analysis. The structural optimization results provide a valuable check for the weight equations used in the aerodynamic design. In addition, these results confirm the need for using simple, algebraic models in conjunction with more detailed analysis methods. A strategy of interlaced aerodynanic-structural design is proposed.

Hutchison, M. G.↗

Integrated aerodynamic-structural-control wing design

The aerodynamic-structural-control design of a forward-swept composite wing for a high subsonic transport aircraft is considered. The structural analysis is based on a finite-element method. The aerodynamic calculations are based on a vortex-lattice method, and the control calculations are based on an output feedback control. The wing is designed for minimum weight subject to structural, performance/aerodynamic and control constraints. Efficient methods are used to calculate the control-deflection and control-effectiveness sensitivities which appear as second-order derivatives in the control constraint equations. To suppress the aeroelastic divergence of the forward-swept wing, and to reduce the gross weight of the design aircraft, two separate cases are studied: (1) combined application of aeroelastic tailoring and active controls; and (2) aeroelastic tailoring alone. The results of this study indicated that, for this particular example, aeroelastic tailoring is sufficient for suppressing the aeroelastic divergence, and the use of active controls was not necessary.

Rais-Rohani, M.↗

Current status of computational methods for transonic unsteady aerodynamics and aeroelastic applications

The current status of computational methods for unsteady aerodynamics and aeroelasticity is reviewed. The key features of challenging aeroelastic applications are discussed in terms of the flowfield state: low-angle high speed flows and high-angle vortex-dominated flows. The critical role played by viscous effects in determining aeroelastic stability for conditions of incipient flow separation is stressed. The need for a variety of flow modeling tools, from linear formulations to implementations of the Navier-Stokes equations, is emphasized. Estimates of computer run times for flutter calculations using several computational methods are given. Application of these methods for unsteady aerodynamic and transonic flutter calculations for airfoils, wings, and configurations are summarized. Finally, recommendations are made concerning future research directions.

Edwards, J. W.↗

Aerodynamic predictions and experimental results for an Advanced Manned Launch System orbiter configuration

The results from a series of wind-tunnel tests are presented along with predictions of the aerodynamic characteristics for a proposed Advanced Manned Launch System orbiter configuration. The predicted characteristics were made using the Aerodynamic Preliminary Analysis System (APAS), and were shown to be of sufficient accuracy for use in preliminary configuration analysis. Various methods of analysis were used in the APAS system, and the results of each were compared with the wind-tunnel dam. The accuracy of the predicted data varied over the Mach range studied. The best agreement between the wind-tunnel data and the APAS predictions occurr4ed in the low subsonic and the high supersonic regimes, while the low supersonic predictions resulted in only fair agreement. The APAS paneled-body analysis method (low speed) and the HABP impact analysis method (high speed) gave the most accurate results when compared against the experimental data.

Engelund, Walter C.↗

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed in this paper using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated in this paper by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-18 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

Brenner, Martin J.↗

Aerodynamics of Shuttle Orbiter at high altitudes

The high-altitude/high-Knudsen number aerodynamics of the Shuttle Orbiter are computed from Low-Earth Orbit down to 100 km using three-dimensional direct simulation Monte Carlo and free molecule codes. Results are compared with Blanchard's latest Shuttle aerodynamic model, which is based on in-flight accelerometer measurements, and bridging formula models. Good comparison is observed, except for the normal force and pitching moment coefficients. The present results were obtained for a generic Shuttle geometry configuration corresponding to a zero deflection for all control surfaces.

Rault, Didier F. G.↗

Grid and aerodynamic sensitivity analyses of airplane components

An algorithm is developed to obtain the grid sensitivity with respect to design parameters for aerodynamic optimization. The procedure is advocating a novel (geometrical) parameterization using spline functions such as NURBS (Non-Uniform Rational B-Splines) for defining the wing-section geometry. An interactive algebraic grid generation technique, known as Two-Boundary Grid Generation (TBGG) is employed to generate C-type grids around wing-sections. The grid sensitivity of the domain with respect to geometric design parameters has been obtained by direct differentiation of the grid equations. A hybrid approach is proposed for more geometrically complex configurations such as a wing or fuselage. The aerodynamic sensitivity coefficients are obtained by direct differentiation of the compressible two-dimensional thin-layer Navier-Stokes equations. An optimization package has been introduced into the algorithm in order to optimize the wing-section surface. Results demonstrate a substantially improved design due to maximized lift/drag ratio of the wing-section.

Sadrehaghighi, Ideen↗

Estimation of effective aerodynamic roughness with altimeter measurements

A new method is presented for estimating the aerodynamic roughness length of heterogeneous land surfaces and complex landscapes using elevation measurements performed with an airborne laser altimeter and the Seasat radar altimeter. Land surface structure is characterized at increasing length scales by considering three basic landscape elements: (1) partial to complete canopies of herbaceous vegetation; (2) sparse obstacles (e.g., shrubs and trees); and (3) local relief. Measured parameters of land surface geometry are combined to obtain an effective aerodynamic roughness length which parameterizes the total atmosphere-land surface stress.

Menenti, M.↗

Dynamic-overlapped-grid simulation of aerodynamically determined relative motion

Currently, there is a need to develop a means of analyzing and studying unsteady flowfields which involve multiple component configurations with at least one of the components in relative motion with respect to the others. Two of the important phenomena that such analyses can help to understand are the unsteady aerodynamic interference and the boundary-induced component of the flowfield. With this motivation, a computational method is developed which couples the governing equations of the unsteady flowfield and the rigid-body dynamics in six degrees-of-freedom. These equations are solved on composite meshes of overlapped subdomain grids which can move with respect to each other. Initially, several measures that reduce the numerical error are studied and compared with the exact solution of a moving normal shock in a tube. It is concluded that a second-order accurate method, for spatial and temporal discretizations as well as for the moving subdomain interpolations, is needed as a minimum measure. Furthermore, the CFL numbers should be restricted to unity. Then, the method is used to simulate the flowfield history and predict the aerodynamically determined trajectory of a store dropped from its initial position under a wing.

Yen, Guan-Wei↗

Kinematics and aerodynamics of the velocity vector roll

The velocity vector roll is an angular rotation of an aircraft about its instantaneous velocity vector, constrained to be performed at constant angle-of-attack (AOA), no sideslip, and constant velocity. Consideration of the aerodynamic force equations leads to requirements for body-axis yawing and pitching rotations that satisfy these constraints. Here, the body axis rotations, and the constraints, are used in the moment equations to determine the aerodynamic moments required to perform the velocity vector roll. For representative tactical aircraft, the conditions for maximum pitching moment are a function of orientation, occurring at about 90 deg of bank in a level trajectory. Maximum required pitching moment occurs at peak roll rate, and is achieved at AOA above 45 deg. The conditions for maximum rolling moment depend on the value of the roll mode time constant. For a small time constant (fast response) the maximum rolling moment occurs at maximum roll acceleration and zero AOA, largely independent of aircraft orientation; for a large time constant, maximum required rolling moment occurs at maximum roll rate, at maximum AOA, and at 180 deg of bank in level flight. Maximum yawing moment occurs at maximum roll acceleration, maximum AOA, and is largely independent of airplane orientation.

Durham, Wayne C.↗

Simulated rarefied aerodynamics of the Magellan spacecraft during aerobraking

Aerodynamic loads upon the Magellan spacecraft during aerobraking through the atmosphere of Venus are computed at off-design attitudes with a direct simulation Monte Carlo (DSMC) particle method. Simulated rarefied flows at nominal altitudes near 140 km and an entry speed of 8.6 km/s were compared to simulated and analytic free molecular results. Aerodynamic moments, forces, and heating for rarefied entry at all attitudes were 7-10 percent below free molecular results. All moments acted to restore the vehicle to its nominal zero-pitch, zero-yaw attitude. Suggested canting of the solar panels is an innovative configuration to assess gas-surface interaction during aerobraking. The resulting roll torques about the central body-axis as predicted in rarefied flow simulations were nearly twice that predicted for free molecular flow, although differences became less distinct for thermal accommodation coefficients well below unity. Roll torques increased dramatically with reduced accommodation coefficients employed in the simulation. In the DSMC code, periodic free-molecule boundary conditions and a coarse computational grid and body resolution served to minimize the simulation size and cost while retaining solution validity.

Haas, Brian L.↗

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Morris, Stephen James↗

Efficient optimization of integrated aerodynamic-structural design

The introduction of composite materials is having a profound effect on the design process. Because these materials permit the designer to tailor material properties to improve structural, aerodynamic and acoustic performance, they require a more integrated multidisciplinary design process. Because of the complexity of the design process numerical optimization methods are required. The present paper is focused on a major difficulty associated with the multidisciplinary design optimization process - its enormous computational cost. We consider two approaches for reducing this computational burden: (1) development of efficient methods for cross-sensitivity calculation using perturbation methods; and (2) the use of approximate numerical optimization procedures. Our efforts are concentrated upon combined aerodynamic-structural optimization. Results are presented for the integrated design of a sailplane wing. The impact of our computational procedures on the computational costs of integrated costs of integrated designs are discussed.

Haftka, R. T.↗