Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Effects of buoyancy-driven flow and thermal boundary conditions on physical vapor transport

A 2D numerical model was developed in order to ascertain if reduced gravity conditions are beneficial to physical vapor transport (PVT) and to determine its tolerance limits to residual accelerations. This was solved using the PHOENICS finite-volume code. Reduction of gravitational accelerations to less than 0.1 g0 was found to be sufficient to suppress buoyancy-driven convection to an extent that diffusion was the dominant transport mode, whence a greater uniformity in the growth rate could be obtained. It is shown that a uniform temperature gradient on the ampoule walls causes the vapor to be supersaturated throughout the ampoule, potentially resulting in undesirable nucleation at the walls. A 'hump' in the wall temperature profile can be used to avoid this. The prevailing transport conditions determine the size of the hump needed.

Nadarajah, Arunan↗
NASA NTRS1979

Convective instability when the temperature gradient and rotation vector are oblique to gravity. I - Fluids without diffusion

A linear stability analysis of fluid layers under uniform rotation (generally oblique to gravity) which possess both vertical and horizontal temperature gradients is made by considering ideal fluids without diffusion within a Boussinesq approximation. This simplified configuration is used to assess the preferred convective modes as a function of latitude on a planet like Jupiter. The tilted rotation vector introduces a preference for roll-like disturbances with north-south orientations, while the horizontal temperature gradient produces a thermal wind shear which favors convective rolls oriented parallel to the flow in an east-west direction. It is found that the horizontal temperature gradient needed to produce a preference for the axisymmetric or east-west rolls increases with an increasing rotation rate and a decreasing latitude. The parameter values for Jupiter are estimated with the use of a simple radiative convective model, indicating a preference for axisymmetric rolls at nearly all latitudes if the convection zone depth is greater than about 200 km below the one atmosphere pressure level and convective roll characteristics which contribute to an equatorial acceleration.

Hathaway, D. H.↗
NASA NTRS1983

Electrical resistivity of composite superconductors

In addition to its superconducting properties, a superconductor is usually characterized by poor thermal conductivity and relatively high electrical resistivity in the normal state. To remedy this situation a study of superconducting properties of Cu-rich CU-Nb wires prepared by directionally solidified and cold-rolled technique was conducted. Some of the specimens were prepared by melting, directional solidification and diffusing in Tin. A total of 12 wire specimens was tested. Each specimen was analyzed by plotting experimental data into the following curves: the graph of the residual resistivity as a function of the specimen current at 4.3 K; and the graph of the electrical resistivity as a function of the temperature at a constant current.

Davis, J. H.↗
NASA NTRS1994

Spectral emissivity measurements of land-surface materials and related radiative transfer simulations

Spectral radiance measurements have been made in the laboratory and in the field for deriving spectral emissivities of some land cover samples with a spectroradiometer and an auxiliary radiation source in the wavelength range 2.5-14.5 micrometers. A easy and quick four-step method (four steps to measure the sample and a diffuse reflecting plate surface under sunshine and shadowing conditions, respectively) has been used for simultaneous determination of surface temperature and emissivity. We emphasized in-situ measurements in combination with radiative transfer simulations, and an error analysis for basic assumptions in deriving spectral emissivity of land-surface samples from thermal infrared measurements.

Wan, Z.↗
NASA NTRS2020

Inverse Compton Cooling in the Coronae of Simulated Black Hole Accretion Flows

We present a formulation for a local cooling function to be employed in the diffuse, hot corona region of 3D GRMHD simulations of accreting black holes. This new cooling function calculates the cooling rate due to inverse Compton scattering by considering the relevant microphysics in each cell in the corona and approximating the radiation energy density and Compton temperature there by integrating over the thermal seed photon flux from the disk surface. The method either assumes ion and electron tem- peratures are equal (1T), or calculates them separately (2T) using an instantaneous equilibrium approach predicated on the actual relevant rate equations (Coulomb and Compton). The method is shown to be consistent with a more detailed ray-tracing calculation where the bulk of the cooling occurs, but is substantially less costly to per- form. As an example, we apply these methods to a harm3d simulation of a 10M⊙, non-spinning black hole, accreting at nominally 1% the Eddington value. Both 1T and 2T approaches lead to increased radiative efficiency and a larger fraction of total cooling in the corona as compared to the original target-temperature cooling function used by harm3d, especially in the 1T case. Time-averaged post-processing reveals that the continuum spectral observations predicted from these simulations are qualitatively similar to actual X-ray binary data, especially so for the 1T approach which yields a harder power-law component (Γ = 2.25) compared to the 2T version (Γ = 2.53).

Brooks E. Kinch↗
NASA NTRS2023

Aqua MODIS: 20 Years of On-orbit Calibration and Performance

Since its launch in May 2002, Aqua MODIS has successfully operated for more than 20 years and has continuously generated a wide range of data products that have enabled and supported the remote sensing community and users worldwide for their studies of the Earth’s system by monitoring changes in its key environmental parameters. Although Aqua MODIS, designed with a lifetime requirement of 6 years, is currently operated in its extended mission phase, it continues to make high quality global observations of the Earth’s surface via its 36 spectral bands that cover wavelengths from visible to long-wave infrared. To date, all instrument on-board calibrators (OBC) remain capable of performing their design functions, providing various calibration data sets to help monitor on-orbit changes in sensor responses and performance characteristics. In addition to the OBC, regularly scheduled lunar observations and select Earth-view targets are used extensively to support sensor on-orbit calibration, especially for the calibration of the visible channels (or bands). In this paper, we provide an overview of Aqua MODIS on-orbit calibration activities and methodologies for both reflective solar bands (RSB) and thermal emissive bands (TEB), illustrate its on-orbit performance over the past 20 years using examples derived from OBC measurements, lunar observations, and Earth-view response trends, and describe various calibration improvements made over its entire mission. We focus on key issues identified since launch, such as solar diffuser degradation, electronic crosstalk, and on-orbit changes in sensor response versus scan-angle, along with approaches and strategies developed to mitigate their impact on sensor calibration quality. Also discussed in this paper are some of the key calibration enhancements incorporated recently in the Collection 6.1 and the upcoming Collection 7 Level-1B algorithms.

Polarization↗
NASA NTRS1980

Copernicus observations of C I and CO in diffuse interstellar clouds

Copernicus was used to observe absorption lines of C I in its ground state and excited fine structure levels and CO toward 29 stars. We use the C I data to infer densities and pressures within the observed clouds, and because our results are of higher precision than previous work, much more precise estimates of the physical conditions in clouds are obtained. In agreement with previous work, the interstellar thermal pressure appears to be variable, with most clouds having values of p/k between 1000/cu cm K and 10,000/cu cm K, but there are some clouds with p/k as high as 100,000/cu cm K. Our results are consistent with the view that the interstellar thermal pressure is so variable that the gas undergoes continuous dynamic evolution. Our observations provide useful constraints on the physical processes on the surfaces of grains. In particular, we find that grains are efficient catalysts of interstellar H2 in the sense that at least half of the hydrogen atoms that strike grains come off as part of H2. Results place strong constraints on models for the formation and destruction of interstellar CO. In many clouds, an order of magnitude less CO than predicted in some models was found.

Jenkins, E. B.↗
NASA NTRS1971

Exploratory screening tests of several alloys and coatings for automobile thermal reactors

A total of 23 materials (including uncoated ferritic and austenitic iron-base alloys, uncoated nickel and cobalt-base superalloys, and several different coatings on AISI 304 stainless steel) were screened as test coupons on a rack in an automobile thermal reactor. Test exposures were generally 51 hours including 142 thermal cycles of 10 minutes at 1010 + or - 30 C test coupon temperature and 7-minutes cool-down to about 510 C. Materials that exhibited corrosion resistance better than that of Hastelloy X include: a ferritic iron alloy with 6 weight percent aluminum; three nickel-base superalloys; two diffused-aluminum coatings on AISI 304; and a Ni-Cr slurry-sprayed coating on AISI 304. Preliminary comparison is made on the performance of the directly impinged coupons and a reactor core of the same material.

Oldrieve, R. E.↗
NASA NTRS1979

Mechanisms of boron fiber strengthening by thermal treatment

The fracture strain for boron on tungsten fibers was studied for improvement by heat treatment under vacuum or argon environments. The mechanical basis for this improvement is thermally-induced axial contraction of the entire fiber, whereby strength-controlling core flaws are compressed and fiber fracture strain increased by the value of the contraction strain. By highly sensitive measurements of fiber density and volume, the physical mechanism responsible for contraction under both environments was identified as boron atom diffusion out of the fiber sheath. The fiber contracts because the average volume of the resulting microvoid was determined to be only 0.26 plus or minus 0.09 the average atomic volume of the removed atom. The basic and practical implications of these results are discussed with particular emphasis on the theory, use, and limitations of heat-induced contraction as a simple cost-effective secondary processing method.

Dicarlo, J. A.↗
NASA NTRS1979

Mechanisms of boron fiber strengthening by thermal treatment

The fracture strain for boron on tungsten fibers can be improved by heat treatment under vacuum or argon environments. The mechanical basis for this improvement is thermally-induced axial contraction of the entire fiber, whereby strength-controlling core flaws are compressed and fiber fracture strain increased by the value of the contraction strain. By highly sensitive measurements of fiber density and volume, the physical mechanisms responsible for contraction under both environments was identified as boron atom diffusion out of the fiber sheath. The fiber contracts because the average volume of the resulting microvoid was determined to be only 0.26 + or - 0.09 the average atomic volume of the removed atom. The basic and practical implications of these results are discussed with particular emphasis on the theory, use, and limitations of heat-induced contraction as a simple cost-effective secondary processing method.

Dicarlo, J. A.↗
NASA NTRS1981

Hot oxygen atoms in the upper atmosphere of Venus

Using data obtained by an ultraviolet spectrometer on the Pioneer-Venus Orbiter, energy and altitude distribution of nonthermal oxygen atoms in the Venus atmosphere for typical daytime and nighttime conditions are calculated using two different numerical methods. Agreement is found between results obtained by the two-stream transport method and the diffusion equation technique. Dissociative recombination of molecular oxygen ions and charge exchange of atomic oxygen ions with the neutral hydrogen and oxygen gas are the source terms, and calculations show that the dissociative recombination term is the dominant one. It is shown that measured hot atom concentrations exceed estimates of the thermal hydrogen atom concentrations derived from Brinton et al. (1980) over most of the daytime exosphere, and the calculated concentrations do so to an even greater extent. It is concluded that hot oxygen atoms are an important component of the dayside exosphere of Venus, their most important effect being the absorption of solar wind.

Nagy, A. F.↗
NASA NTRS1990

Simple model of plasma acceleration in a magnetic nozzle

A collisionless, steady-state, cold-plasma model is used to calculate the three-dimensional trajectory of a plasma as it is accelerated through a diverging magnetic field. The magnetic field is assumed to be axisymmetric with nonzero radial and axial components and zero azimuthal component. Although random thermal motion of plasma species is neglected in the cold plasma approximation, an important effect of plasma thermal energy is accounted for in the model as the kinetic energy of electrons in their Larmor motion about magnetic field lines. Calculations based on this model confirm previous studies which suggested that plasma separation from the field of a magnetic nozzle can take place even in the absence of collisional diffusion. It is shown that plasma divergence in a magnetic nozzle can be controlled by tailoring the field geometry.

Sercel, Joel C.↗
NASA NTRS1992

Chemical vapor deposition fluid flow simulation modelling tool

Accurate numerical simulation of chemical vapor deposition (CVD) processes requires a general purpose computational fluid dynamics package combined with specialized capabilities for high temperature chemistry. In this report, we describe the implementation of these specialized capabilities in the spectral element code NEKTON. The thermal expansion of the gases involved is shown to be accurately approximated by the low Mach number perturbation expansion of the incompressible Navier-Stokes equations. The radiative heat transfer between multiple interacting radiating surfaces is shown to be tractable using the method of Gebhart. The disparate rates of reaction and diffusion in CVD processes are calculated via a point-implicit time integration scheme. We demonstrate the use above capabilities on prototypical CVD applications.

Bullister, Edward T.↗
NASA NTRS1997

Radiative Effects of Aerosols

During the Atlantic Stratocumulus Transition Experiment (ASTEX) in June 1992, two descents in cloud-free regions allowed comparison of the change in aerosol optical depth as determined by an onboard total-direct-diffuse radiometer (TDDR) to the change calculated from measured size resolved aerosol microphysics and chemistry. Both profiles included pollution haze layer from Europe but the second also included the effect of a Saharan dust layer above the haze. The separate contributions of supermicrometer (coarse) and submicrometer (fine) aerosol were determined and thermal analysis of the pollution haze indicated that the fine aerosol was composed primarily of a sulfate/water mixture with a refractory soot-like core.

Valero, Francisco P. J.↗
NASA NTRS2012

An Overview of MODIS On-orbit Operation, Calibration, and Lessons

Two nearly identical copies of the Moderate Resolution Imaging Spectroradiometer (MODIS) have successfully operated onboard the Terra and Aqua spacecraft for more than II years and 9 years since their launch in December 1999 and May 2002, respectively. MODIS is a key instrument for the NASA's Earth Observing System (EOS) missions. MODIS observations have produced an unprecedented amount and a broad range of data products and significantly benefited the science and user community. Its follow-on instrument, the Visible/Infrared Imager Radiometer Suite (VIIRS) on-board the NPOESS Preparatory Project (NPP) spacecraft, is currently scheduled for launch in late October, 2011. The NPP serves as a bridge mission between EOS and the Joint Polar Satellite System (JPSS). MODIS collects data in 36 spectral bands, covering spectral regions from visible (VIS) to long-wave infrared (L WIR), and at three different spatial resolutions. Because of its stringent design requirements, MODIS was built with a complete set of onboard calibrators, including a solar diffuser (SO), a solar diffuser stability monitor (SDSM), a blackbody (BB), a spectroradiometric calibration assembly (SRCA), and a space view (SV) port. Except for tbe SRCA, VIlRS carries the same set of onboard calibrators as MODIS. The SD/SDSM system is used together to calibrate tbe reflective solar bands (RSB). The BB is designed for the thermal emissive bands (TEB) calibration. Similar to Terra and Aqua MODIS, VIlRS will also make regular lunar observations to monitor RSB radiometric calibration stability. In this paper, we provide an overview of MODIS on-orbit operation and calibration activities and present issues identified and lessons learned from mission-long instrument operations and implementation of various calibration and characterization strategies. Examples of both Terra and Aqua MODIS instrument on-orbit performance, including their similarities and unique characteristics, are discussed in tbe context of what might be expected from and benefited to tbe NPP VIlRS operation and calibration. It is anticipated that MODIS experience and lessons will also provide valuable information for other earth observing missions/sensors.

Xiong, Jack↗
NASA NTRS2013

Bismuth Passivation Technique for High-Resolution X-Ray Detectors

The Athena-plus team requires X-ray sensors with energy resolution of better than one part in 3,000 at 6 keV X-rays. While bismuth is an excellent material for high X-ray stopping power and low heat capacity (for large signal when an X-ray is stopped by the absorber), oxidation of the bismuth surface can lead to electron traps and other effects that degrade the energy resolution. Bismuth oxide reduction and nitride passivation techniques analogous to those used in indium passivation are being applied in a new technique. The technique will enable improved energy resolution and resistance to aging in bismuth-absorber-coupled X-ray sensors. Elemental bismuth is lithographically integrated into X-ray detector circuits. It encounters several steps where the Bi oxidizes. The technology discussed here will remove oxide from the surface of the Bi and replace it with nitridized surface. Removal of the native oxide and passivating to prevent the growth of the oxide will improve detector performance and insulate the detector against future degradation from oxide growth. Placing the Bi coated sensor in a vacuum system, a reduction chemistry in a plasma (nitrogen/hydrogen (N2/H2) + argon) is used to remove the oxide and promote nitridization of the cleaned Bi surface. Once passivated, the Bi will perform as a better X-ray thermalizer since energy will not be trapped in the bismuth oxides on the surface. A simple additional step, which can be added at various stages of the current fabrication process, can then be applied to encapsulate the Bi film. After plasma passivation, the Bi can be capped with a non-diffusive layer of metal or dielectric. A non-superconducting layer is required such as tungsten or tungsten nitride (WNx).

Chervenak, James↗
NASA NTRS2023

Homogeneity Study of ZrC, NbC, and TaC Binary Carbide Fuels for the Application of Nuclear Thermal Propulsion

In alignment with NASA and DARPA goals, efforts towards Nuclear Thermal Propulsion (NTP) have increased in recent years. As progress is made, a main challenge still exists; the fuel in an NTP system must survive the extreme environment experienced during operating conditions. Three fuel forms have been studied including a ceramic-metallic matrix, a ceramic-ceramic matrix, and solid solution carbides. Solid solution carbides were studied previously as a fuel for NTP and was shown to be a promising technology; however, the programs were canceled before demonstration in an NTP engine test. Of the refractory metal carbides of interest, zirconium carbide (ZrC), niobium carbide (NbC) and tantalum carbide (TaC) were studied. ZrC, NbC, and TaC powders were consolidated in monocarbide (ZrC, NbC, TaC) and bi-carbide (ZrC-NbC, ZrC-TaC, NbC-TaC) forms using spark plasma sintering (SPS), with 50-50 mol% compositions of the bi-carbides of interest. The time and temperature conditions to achieve a completely homogeneous solid solution for the mixed carbides is of interest for NTP fuel applications, since this homogeneity is considered to be essential for this fuel form. Homogeneity is typically not achieved during sintering, as surface diffusion (predominant for sintering to near ideal density) tends to occur at lower temperatures than bulk volumetric diffusion (required for solute interdiffusion to achieve a homogeneous solid solution). High temperature isochronal annealing was performed to identify the conditions to achieve a chemically homogeneous sample. The solute interpenetration vs annealing temperature was quantified using energy dispersion spectroscopy (EDS) in a scanning electron microscope (SEM). X-ray diffraction (XRD) was used to accurately measure the phase stability and lattice parameter as a function of annealing conditions. The diffusion data from each sample was then used to determine self-diffusion coefficients for interdiffusion of the Nb, Zr, and Ta solutes and compared to existing literature values. The minimum annealing conditions to achieve complete chemical homogeneity for each carbide was determined.

nuclear thermal propulsion↗
NASA NTRS2012

Constraints on the Galactic Halo Dark Matter from Fermi-LAT Diffuse Measurements

We have performed an analysis of the diffuse gamma-ray emission with the Fermi Large Area Telescope (LAT) in the Milky Way halo region, searching for a signal from dark matter annihilation or decay. In the absence of a robust dark matter signal, constraints are presented. We consider both gamma rays produced directly in the dark matter annihilation/decay and produced by inverse Compton scattering of the e+/e− produced in the annihilation/decay. Conservative limits are derived requiring that the dark matter signal does not exceed the observed diffuse gamma-ray emission. A second set of more stringent limits is derived based on modeling the foreground astrophysical diffuse emission using the GALPROP code. Uncertainties in the height of the diffusive cosmic-ray halo, the distribution of the cosmic-ray sources in the Galaxy, the index of the injection cosmic-ray electron spectrum, and the column density of the interstellar gas are taken into account using a profile likelihood formalism, while the parameters governing the cosmic-ray propagation have been derived from fits to local cosmic-ray data. The resulting limits impact the range of particle masses over which dark matter thermal production in the early universe is possible, and challenge the interpretation of the PAMELA/Fermi-LAT cosmic ray anomalies as the annihilation of dark matter.

DIFFUSE MEASUREMENTS↗