Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Single-ion magnetism in the extended solid-state: insights from X-ray absorption and emission spectroscopy

Large single-ion magnetic anisotropy is observed in lithium nitride doped with iron. The iron sites are two-coordinate, putting iron doped lithium nitride amongst a growing number of two coordinate transition metal single-ion magnets (SIMs). Uniquely, the relaxation times to magnetisation reversal are over two orders of magnitude longer in iron doped lithium nitride than other 3d-metal SIMs, and comparable with high-performance lanthanide-based SIMs. To understand the origin of these enhanced magnetic properties a detailed characterisation of electronic structure is presented. Access to dopant electronic structure calls for atomic specific techniques, hence a combination of detailed single-crystal X-ray absorption and emission spectroscopies are applied. Together K-edge, L 2,3 -edge and Kβ X-ray spectroscopies probe local geometry and electronic structure, identifying iron doped lithium nitride to be a prototype, solid-state SIM, clean of stoichiometric vacancies where Fe lattice sites are geometrically equivalent. Extended X-ray absorption fine structure and angular dependent single-crystal X-ray absorption near edge spectroscopy measurements determine Fe I dopant ions to be linearly coordinated, occupying a D 6h symmetry pocket. The dopant engages in strong 3dπ-bonding, resulting in an exceptionally short Fe–N bond length (1.873(7) Å) and rigorous linearity. It is proposed that this structure protects dopant sites from Renner–Teller vibronic coupling and pseudo Jahn–Teller distortions, enhancing magnetic properties with respect to molecular-based linear complexes. The Fe ligand field is quantified by L 2,3 -edge XAS from which the energy reduction of 3d z 2 due to strong 4s mixing is deduced. Quantification of magnetic anisotropy barriers in low concentration dopant sites is inhibited by many established methods, including far-infrared and neutron scattering. We deduce variable temperature L 3 -edge XAS can be applied to quantify the J = 7/2 magnetic anisotropy barrier, 34.80 meV (~280 cm –1 ), that corresponds with Orbach relaxation via the first excited, M J = ±5/2 doublet. The results demonstrate that dopant sites within solid-state host lattices could offer a viable alternative to rare-earth bulk magnets and high-performance SIMs, where the host matrix can be tailored to impose high symmetry and control lattice induced relaxation effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal decomposition of t-butylamine borane studied by in situ solid state NMR

Development of suitable materials to store hydrogen for automotive use has received pointed attention over the past decade. Significant progress has been made with the discovery of novel chemical hydrides, complex metal hydrides, and adsorption substrates which continue to optimize both thermodynamics and kinetics of hydrogen sorption. Chemical hydrides typically offer the largest theoretical gravimetric capacities. Autrey et al. have recently shown that mechanical milling of alkali metal hydrides with ammonia borane can further lower the decomposition temperature. In all cases, however, many challenges remain in order to meet the current US DOE performance targets. Amine boranes are being considered for hydrogen storage materials since they contain significant quantities of hydrogen which potentially can be released at low temperatures (80-150 C) via chemical reactions. Ammonia borane, NH{sub 3}BH{sub 3}, is one of the most promising in this class as it decomposes to release greater than two moles of pure hydrogen gas (14 wt%) below 160 C. Although isoelectronic to ethane, NH{sub 3}BH{sub 3} is a solid at room temperature due to the di-hydrogen bonding network formed between the amine protons and boron hydrides in the solid state lattice. Further, it has been shown that the hydrogen release mechanism involves transformation and isomerization to an ionic dimer where a hydride migrates from one boron to the adjacent boron in the dimer. The greatest challenge to the use of ammonia borane as a hydrogen fuel is the regeneration path from spent fuel to ammonia borane again. The proposed chemical synthesis involves complicated organometallic reactions to form boron hydrogen bonds from the thermodynamically stable polyimidoborane products (BNH){sub n}. Recent theoretical calculations suggested that incorporation of carbon atoms into the (BNH)n product would be less thermodynamically stable. These (CBNH)n compounds are potentially less energy intensive making regeneration of the amine borane fuel more feasible [22]. In the present study, tert-butylamine borane is investigated by heteronuclear in situ solid state NMR to understand hydrogen release from a hydrocarbon containing amine borane. tbutylamine borane has similar physical properties to amine borane with a melting point of 96 C. A single proton has been replaced with a t-butylamine group resulting in a weakening of the dihydrogen bonding framework. t-butylamine borane has a theoretical gravimetric hydrogen density of 15.1%; however, isobutane can also be evolved rather than hydrogen. If decomposition yields one mole isobutane and two moles hydrogen, 4.5 wt% H2 gas will be evolved. More importantly for the present work, the resulting spent fuel should be comprised of both (BNH)n and (CBNH)n polyimidoboranes.

08 HYDROGEN↗

Cassini Solid State Recorder: A High Capacity, Radiation Tolerant High-Performance Unit

Onboard the Cassini spacecraft, and the subject of this paper, are two Solid State Recorders designed and built by TRW, Inc., of Redondo Beach, California, for NASA's Jet Propulsion Laboratory. These recorders, which were the first ones designed and selected by NASA for a space program, represent the new frontier and a new beginning for spaceborne data storage.

Cassini↗

Self-powered solid-state photodetector based on TiO{sub 2} nanorod/spiro-MeOTAD heterojunction

A nanostructured solid-state photodetector based on an inorganic/organic semiconductor heterojunction of TiO{sub 2} nanorod/spiro-MeOTAD is constructed. Spiro-MeOTAD serves as the active absorption layer and TiO{sub 2} offers a direct pathway for electron transport. A maximum photoresponsivity of 0.01 A/W was observed under illumination of 410 nm at 0 V bias. The time response (decay time is 0.06 s and rise time is 0.12 s) was observed to be rapid. The self-powered device is a promising candidate for application in high-sensitivity and high-speed blue light photodetectors. These results provided a simple way to fabricate low-cost, high spectrum selectivity hybrid photodetector with large area.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Electrochemical reactivity of atomic and molecular species under solid-state confinement

The nanoconfinement of electrochemically-active guest species in host solid state electrode materials provides opportunities to tune mass transport between the bulk electrolyte and inner surface of the electrode, enhance electron-transfer rates, and/or improve the stability and dispersion of active material. Here, this review summarizes recent experimental and theoretical electrochemical studies of three types of nanoconfined guest species: (1) ion adsorption of electrolyte ions, (2) confined redox-active molecules, and (3) electrocatalytic reactions of confined ions/solvents and catalytic particles. The examples discussed in this review illustrate how the confinement of guest species within enclosed spaces with nanoscale dimensions – such as pores, pockets, channels, and interlayers – can lead to improved electrochemical performance.

25 ENERGY STORAGE↗

Solid-State NMR Examination of Alteration Layers on a Nuclear Waste Glasses

Solid-state NMR is a powerful tool for probing the role and significance of alteration layers in determining the kinetics for the corrosion of nuclear waste glass. NMR methods are used to probe the chemical structure of the alteration layers to elucidate information about their chemical complexity, leading to increased insight into the mechanism of altered layer formation. Two glass compositions were examined in this study: a glass preliminarily designed for nuclear waste immobilization (called AFCI) and a simplified version of this AFCI glass (which we call SA1R). Powdered glasses with controlled and known particles sizes were corroded at 90 °C for periods of one and five months with a surface-area to solution-volume ratio of 100,000 m-1. 1H-29Si CP-CPMG MAS NMR, 1H-27Al CP-MAS NMR, 1H-11B CP-MAS NMR, and 1H-23Na CP-MAS NMR experiments provide isolated structural information about the alteration layers, which differ in structure from that of the pristine glass. Both glasses studied here develop alteration layers composed primarily of [IV]Si species. Aluminum is also retained in the alteration layers, perhaps facilitated by the observed increase in coordination from [IV]Al to [VI]Al, which correlates with a loss of charge balancing cations. 1H-11B CP-MAS NMR observations indicated a retention of boron in hydrated glass layers, which has not been characterized by previous work. For the AFCI glass, secondary phase formation begins during the corrosion times considered here, and these neophases are detected within the alteration layers. We identify precursor phases as crystalline sodium metasilicates. An important finding is that layer thickness depends on the length of the initial alteration stages and varies only with respect to silicon species during the residual rate regime.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Solid state synthesis of water-dispersible silicon nanoparticles from silica nanoparticles

A solid state synthesis for obtaining nanocrystalline silicon was performed by high temperature reduction of commercial amorphous nanosilica with magnesium powder. The obtained silicon powder contains crystalline silicon phase with lattice spacings characteristic of diamond cubic structure (according to high resolution TEM), and an amorphous phase. In {sup 29}Si CP MAS NMR a broad multicomponent peak corresponding to silicon is located at -61.28 to -69.45 ppm, i.e. between the peaks characteristic of amorphous and crystalline Si. The powder has displayed red luminescence while excited under UV illumination, due to quantum confinement within the nanocrystals. The silicon nanopowder was successfully dispersed in water containing poly(vinyl alcohol) as a stabilizing agent. The obtained dispersion was also characterized by red photoluminescence with a band maximum at 710 nm, thus enabling future functional coating applications. - Graphical abstract: High temperature reduction of amorphous nanosilica with magnesium powder results in the formation of powder containing crystalline silicon phase The powder displays red luminescence while excited under UV illumination, due to quantum confinement within the Si nanocrystals, and can be successfully dispersed in water containing poly(vinyl alcohol) as a stabilizing agent. The obtained dispersion was also characterized by red photoluminescence, thus enabling future functional coating applications.

36 MATERIALS SCIENCE↗

L70 life prediction for solid state lighting using Kalman Filter and Extended Kalman Filter based models

Solid-state lighting (SSL) luminaires containing light emitting diodes (LEDs) have the potential of seeing excessive temperatures when being transported across country or being stored in non-climate controlled warehouses. They are also being used in outdoor applications in desert environments that see little or no humidity but will experience extremely high temperatures during the day. This makes it important to increase our understanding of what effects high temperature exposure for a prolonged period of time will have on the usability and survivability of these devices. Traditional light sources “burn out” at end-of-life. For an incandescent bulb, the lamp life is defined by B50 life. However, the LEDs have no filament to “burn”. The LEDs continually degrade and the light output decreases eventually below useful levels causing failure. Presently, the TM-21 test standard is used to predict the L70 life of LEDs from LM-80 test data. Several failure mechanisms may be active in a LED at a single time causing lumen depreciation. The underlying TM-21 Model may not capture the failure physics in presence of multiple failure mechanisms. Correlation of lumen maintenance with underlying physics of degradation at system-level is needed. In this paper, Kalman Filter (KF) and Extended Kalman Filters (EKF) have been used to develop a 70-percent Lumen Maintenance Life Prediction Model for LEDs used in SSL luminaires. Ten-thousand hour LM-80 test data for various LEDs have been used for model development. System state at each future time has been computed based on the state space at preceding time step, system dynamics matrix, control vector, control matrix, measurement matrix, measured vector, process noise and measurement noise. The future state of the lumen depreciation has been estimated based on a second order Kalman Filter model and a Bayesian Framework. The measured state variable has been related to the underlying damage using physics-based models. Life prediction of L70 life for the LEDs used in SSL luminaires from KF and EKF based models have been compared with the TM-21 model predictions and experimental data.

Lall, Pradeep↗

Solid-State Lighting 2017 Suggested Research Topics

A 2017 update to the Solid-State Lighting R&D Plan that is divided into two documents. The first document describes a list of suggested SSL priority research topics and the second document provides context and background, including information drawn from technical, market, and economic studies. Widely referenced by industry and government both here and abroad, these documents reflect SSL stakeholder inputs on key R&D topics that will improve efficacy, reduce cost, remove barriers to adoption, and add value for LED and OLED lighting solutions over the next three to five years, and discuss those applications that drive and prioritize the specific R&D.

47 OTHER INSTRUMENTATION↗

Solid-State Lighting 2017 Suggested Research Topics

A 2017 update to the Solid-State Lighting R&D Plan that is divided into two documents. The first document describes a list of suggested SSL priority research topics and the second document provides context and background, including information drawn from technical, market, and economic studies. Widely referenced by industry and government both here and abroad, these documents reflect SSL stakeholder inputs on key R&D topics that will improve efficacy, reduce cost, remove barriers to adoption, and add value for LED and OLED lighting solutions over the next three to five years, and discuss those applications that drive and prioritize the specific R&D.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Beam breakup in a solid state powered linear induction accelerator

It has been proposed to use solid-state pulsed-power modules to power the new Scorpius accelerator. Since this highcurrent accelerator would have 360 gaps (more than five times the number of cells as present radiography LIAs), it is natural to be concerned about the beam-breakup (BBU) instability. Earlier calculations of this effect used a half-scale model of the accelerator to avoid the limitation to 200 gaps in the code. We have now updated the code to accommodate the extraordinary number of gaps in this proposed LIA. The results of these early simulations are presented here. They indicate that BBU can only be suppressed to the same level as in designs powered by conventional pulsed power, if the calculated cell impedance can truly be achieved in practice. The magnetic focusing field required for this is of the same order as the field required for a conventionally powered LIA only if the transverse impedance can indeed be constrained to the values obtained in some simulations of the cell.

42 ENGINEERING↗

A solid-state converter for measurement of aircraft noise and sonic boom

A solid-state converter, used in a system of instrumentation for measuring aircraft noise and sonic boom, features a dual-gate FET mixer and an output stage designed for compatibility with a zero drive amplifier. With a half-inch condenser microphone the converter itself has an operating frequency range from dc-28 kHz (-3 dB), a dynamic range of 72 dB, and a noise floor of 50 dB in the band from 22.4 Hz to 22.4 kHz; the system requires no impedance matching networks and is insensitive to cable length up to at least 3000 ft.

Zuckerwar, A. J.↗

Kilovolt dc solid state remote power controller development

The experience gained in developing and applying solid state power controller (SSPC) technology at high voltage dc (HVDC) potentials and power levels of up to 25 kilowatts is summarized. The HVDC switching devices, power switching concepts, drive circuits, and very fast acting overcurrent protection circuits were analyzed. A 25A bipolar breadboard with Darlington connected switching transistor was built. Fault testing at 900 volts was included. A bipolar transistor packaged breadboard design was developed. Power MOSFET remote power controller (RPC) was designed.

Mitchell, J. T.↗

Characterization of a 30-GHz IMPATT solid state amplifier

Described are the characterization and testing of a 20 W solid state amplifier operating in the Ka band to be used in low cost experimental ground terminals. The amplifier was developed by the TRW Electronic Systems Group under NASA Contract NAS3-23266 as a proof-of-concept (POC) device in support of the Advanced Communications Technology Satellite (ACTS) program. Additional goals were development of high-power IMPATT devices and circulators, and multistage diode circuits, which are an integral part of the amplifier. The amplifier underwent acceptance testing at the NASA Lewis Research Center, Cleveland, Ohio. Characteristics measured include the output power of 42 dB m, gain of 30 dB, an injection-locking RF bandwidth of 260 MHz, and an overall direct current-to-radiofrequency (dc-to-RF) efficiency of 6.7 percent.

Wald, Lawrence W.↗