Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reflection data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Optimization of the information content of multitemporal Landsat TM data sets for monitoring forest cover disturbance

Procedures that were developed to optimize the information content of multitemporal thematic mapper (TM) data sets for forest cover disturbance monitoring in Minnesota are described. TM imagery from three different years was calibrated to exoatmospheric reflectance. An atmospheric correction routine was applied combining two major components, atmospheric normalization over time and transformation to ground reflectance. Atmospheric conditions were modeled over time using regression functions derived from five ground features known to be unchanged over the time interval of interest and spanning the entire image reflectance range. The correlation between digital data and the forest cover was subsequently maximized and irrelevant information content was reduced by converting the band-specific reflectances into seven vegetation indices that were assumed to carry unique information. The application of two change detection algorithms to these seven indices ultimately resulted in 14 change features for each time interval of interest. Results show that the preprocessing sequence is vital to forest cover monitoring methodology.

Coppin, Pol R.↗
NASA NTRS1990

Comparison of in situ and satellite-derived reflectances of Forbindels Glacier, Greenland

In situ and Landsat Thematic Mapper (TM)-derived reflectances of the Forbindels Glacier, Greenland, were acquired in August of 1986. Reflectance was measured in situ using a portable spectrometer and calculated using TM data and ancillary information. Atmospheric corrections were applied to the at-satellite reflectances resulting in a 5-17 percent increase in reflectance relative to the calculated at-satellite reflectances. The satellite-derived, corrected reflectances obtained from the non-saturated TM bands corresponded to within 6 percent of the in situ reflectances measured at the nadir viewing angle with a portable spectrometer. Measurement of nadir reflectances using Landsat-TM data appears to be a viable method to obtain physically meaningful reflectances of ice and snow.

Hall, D. K.↗
NASA NTRS1991

Recovery of reflectance from imaging spectrometer measured radiance using a radiative transfer code

Radiance data were acquired over part of the Clark Mountain Range, California in 1990 by the Airborne Visible Infrared Imaging Spectrometer (AVIRIS). From these calibrated radiance data, the lateral distribution of water vapor in precipitable mm was recovered through analysis of the 940 nm water absorption. Surface pressure height was calculated from the 760 nm oxygen absorption band in the AVIRIS data. Surface slopes are estimated from relative elevations derived from the equivalent water vapor elevation for a standard atmosphere. Atmospheric optical depths measured at the Mountain Pass site in these data are extended to the entire region and varied based on the calculated surface pressure elevation. These parameters, derived from every AVIRIS spatial element, are used to constrain the LOWTRAN 7 radiative transfer code for the recovery of surface reflectance. Once transformed to reflectance, the imaging spectrometer data may be analyzed quantitatively for determination of surface composition, and compared with reflectance measurements acquired from different locations, times, and instruments.

Green, Robert O.↗
NASA NTRS1992

Magnetic resonance imaging and electromyography as indexes of muscle function

A hypothesis is tested that exercise-induced magnetic resonance (MR) contrast shifts would relate to electromyography (EMG) amplitude if both measures reflect muscle use during exercise. Both magnetic resonance images (MRI) and EMG data were obtained for separate eccentric (ECC) and cocentric (CON) exercise of increasing intensity for seven subjects 30-32 yr old. CON and ECC actions caused increased integrated EMG (IEMG) and T2 values which were strongly related with relative resistance. The rate of increase and absolute value of both T2 and IEMG were found to be greater for CON than for ECC actions. For both actions IEMG and T2 were correlated. Data obtained suggest that surface IEMG accurately reflects the contractile behavior of muscle and exercise-induced increases in MRI T2 values reflect certain processes that scale with muscle use.

Adams, Gregory R.↗
NASA NTRS2007

Method for Constructing Composite Response Surfaces by Combining Neural Networks with Polynominal Interpolation or Estimation Techniques

A method and system for data modeling that incorporates the advantages of both traditional response surface methodology (RSM) and neural networks is disclosed. The invention partitions the parameters into a first set of s simple parameters, where observable data are expressible as low order polynomials, and c complex parameters that reflect more complicated variation of the observed data. Variation of the data with the simple parameters is modeled using polynomials; and variation of the data with the complex parameters at each vertex is analyzed using a neural network. Variations with the simple parameters and with the complex parameters are expressed using a first sequence of shape functions and a second sequence of neural network functions. The first and second sequences are multiplicatively combined to form a composite response surface, dependent upon the parameter values, that can be used to identify an accurate mode

Rai, Man Mohan↗
NASA NTRS2011

Coupling Between Doppler Radar Signatures and Tornado Damage Tracks

On April 27, 2011, the southeastern United States was raked with several episodes of severe weather. Numerous tornadoes caused extensive damage, and tragically, the deaths of over 300 people. In Alabama alone, there were 61 confirmed tornados, 4 of them produced EF5 damage, and several were on the ground an hour or more with continuous damage tracks exceeding 80km. The use of Doppler radars covering the region provided reflectivity and velocity signatures that allowed forecasters to monitors the severe storms from beginning to end issuing hundreds of severe weather warnings throughout the day. Meteorologists from the the NWS performed extensive surveys to assess the intensity, duration, and ground track of tornadoes reported during the event. Survey activities included site visits to the affected locations, analysis of radar and satellite data, aerial surveys, and interviews with eyewitnesses. Satellite data from NASA's MODIS and ASTER instruments played a helpful role in determining the location of tornado damage paths and in the assessment. High resolution multispectral and temporal composites helped forecasters corroborate their damage assessments, determine starting and ending points for tornado touchdowns, and helped to provide forecasters with a better big-picture view of the damage region. The imagery also helped to separate damage from the April 27th tornados from severe weather that occurred earlier that month. In a post analysis of the outbreak, tornado damage path signatures observed in the NASA satellite data have been correlated to "debris ball" signatures in the NWS Doppler radars and a special ARMOR dual-polarization radar operated by the University of Alabama Huntsville during the event. The Doppler radar data indicates a circular enhanced reflectivity signal and rotational couplet in the radial velocity likely associated with the tornado that is spatially correlated with the damage tracks in the observed satellite data. An algorithm to detect and isolate the "debris ball" from precipitation signatures in the dual polarization radar data has been developed and verified using the NASA damage track data.

Jedlovec, Gary J.↗
NASA NTRS1978

Comparison of aerodynamic data measured in air and Freon-12 wind-tunnel test mediums

An experimental investigation was carried out to measure two dimensional static aerodynamic characteristics of a 65 sub l-213 airfoil in air and Freon-12 (dichlorodifluoromethane) test mediums at corresponding test conditions. The purpose of the tests was to compare measurements in the two test mediums and to evaluate reported methods of converting Freon-12 data to equivalent air values. The test article was a two dimensional wing instrumented to measure chordwise surface pressure distributions. The parameters considered were Mach numbers from 0.6 to 1.0, angles of attack of zero deg and 1 deg, and Reynolds numbers based on model chord from 2,000,000 to 21,000,000. The agreement between data measured in the two test mediums is further improved by application of the transonic or area ratio similarity laws. Where flow conditions are characterized by surface shocks or stall, the effects of flow separation may not be identically reflected in the Freon-12 data, even when converted in accordance with existing similarity laws.

Weller, W. H.↗
NASA NTRS2005

Comparing Goldstone Solar System Radar Earth-based Observations of Mars with Orbital Datasets

The Goldstone Solar System Radar (GSSR) has collected a self-consistent set of delay-Doppler near-nadir radar echo data from Mars since 1988. Prior to the Mars Global Surveyor (MGS) Mars Orbiter Laser Altimeter (MOLA) global topography for Mars, these radar data provided local elevation information, along with radar scattering information with global coverage. Two kinds of GSSR Mars delay-Doppler data exist: low 5 km x 150 km resolution and, more recently, high (5 to 10 km) spatial resolution. Radar data, and non-imaging delay-Doppler data in particular, requires significant data processing to extract elevation, reflectivity and roughness of the reflecting surface. Interpretation of these parameters, while limited by the complexities of electromagnetic scattering, provide information directly relevant to geophysical and geomorphic analyses of Mars. In this presentation we want to demonstrate how to compare GSSR delay-Doppler data to other Mars datasets, including some idiosyncracies of the radar data. Additional information is included in the original extended abstract.

Haldemann, A. F. C.↗
NASA NTRS1978

Landsat spectral signatures - Studies with soil associations and vegetation

The effect of soils and vegetation upon Landsat spectral properties was investigated for a 12,950 hectare area. Six soil associations used for corn, small grains, and grass were analyzed for two dates during the 1974 growing season. Landsat scenes for April 19 and June 30 were studied to separate categories of agricultural land use and to assess the influence of soil association on the spectral signatures of vegetation and bare ground. The April 19 data were useful to separate cropland from grassland and to locate areas of open water. The June 30 data showed that soil associations could not consistently be separated within the data of a single vegetative type; however, the results showed that soils did influence all vegetative spectral reflectances to some degree. Because soils did influence vegetative spectral reflectance, a generalized training set containing data points from each of the six soil associations was used to separate four categories of agricultural land use in the 12,950 hectare test area. An accuracy of about 94% was obtained.

Westin, F. C.↗
NASA NTRS1992

Program For Logarithmic Interpolation Of Test Data

DATASPACE program establishes logarithmically increasing time interval in relaxation data. First takes logarithm of abscissa values, then uses cubic-spline interpolation routine to create evenly spaced array from log values. As result of interpolation, data increasingly spaced. Experimental data curve retained, and interpolated points reflect desired spacing. Applicable to any situation with need for increasingly spaced abscissa values in set of data. Written in FORTRAN 77.

Ledbetter, Frank E., II↗
DOE OSTI2017

Experimental studies of the effects of atomic ordering in epitaxial Ga{sub x}In{sub 1–} {sub x}P alloys on their optical properties

The properties of epitaxial Ga{sub x}In{sub 1–} {sub x}P alloys with an ordered arrangement of atoms in the crystal lattice are studied by a number of spectroscopic methods. The alloys are grown by metal-organic chemical vapor deposition onto single-crystal GaAs(100) substrates. It is shown that, under conditions of the coherent growth of an ordered Ga{sub x}In{sub 1–} {sub x}P alloy on a GaAs(100) substrate, atomic ordering results in radical modifications of the optical properties of the semiconductor compared to the properties of disordered alloys. Among these modifications are a decrease in the band gap and an increase in the luminescence intensity. From the data of dispersion analysis of the infrared dispersion spectra and from ultraviolet spectroscopy data obtained in the transmittance–reflection mode of measurements, the basic optical characteristics, specifically, the dispersion of the refractive index and the high-frequency permittivity of Ga{sub x}In{sub 1–} {sub x}P alloys with ordering are determined. All of the experimental data are in good agreement with the developed theoretical concepts.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Elastohydrodynamic film thickness model for heavily loaded contacts

An empirical elastohydrodynamic (EHD) film thickness formula for predicting the minimum film thickness occurring within heavily loaded contacts (maximum Hertz stresses above 150,000 psi) was developed. The formula was based upon X-ray film thickness measurements made with synthetic paraffinic, fluorocarbon, Type II ester and polyphenyl ether fluids covering a wide range of test conditions. Comparisons were made between predictions from an isothermal EHD theory and the test data. The deduced relationship was found to adequately reflect the high-load dependence exhibited by the measured data. The effects of contact geometry, material and lubricant properties on the form of the empirical model are also discussed.

Loewenthal, S. H.↗
NASA NTRS1973

Elastohydrodynamic film thickness model for heavily loaded contacts

An empirical elastohydrodynamic (EHD) film thickness formula for predicting the minimum film thickness occurring within heavily loaded contacts (maximum Hertz stresses above 1.04 GN/sq m (150,000 psi)) was developed. The formula was based upon X-ray film thickness measurements made with synthetic paraffinic, fluorocarbon, Type II ester, and polyphenyl ether fluids covering a wide range of test conditions. Comparisons were made between predictions from an isothermal EHD theory and the test data. The deduced relationship was found to adequately reflect the high-load dependence exhibited by the measured data. The effects of contact geometry, material, and lubricant properties on the form of the empirical model are also discussed.

Loewenthal, S. H.↗
NASA NTRS1982

The life cycle of thunderstorm gust fronts as viewed with Doppler radar and rawinsonde data

This paper presents the time-dependent analysis of the thunderstorm gust front with the use of Project NIMROD data. RHI cross sections of reflectivity and Doppler velocity are constructed to determine the entire vertical structure. The life cycle of the gust front is divided into four stages: (1) the formative stage; (2) the early mature stage; (3) the late mature stage; and (4) the dissipation stage. A new finding is a horizontal roll detected in the reflectivity pattern resulting from airflow that is deflected upward by the ground, while carrying some of the smaller precipitation ahead of the main echo core of the squall line. This feature is called a 'precipitation roll'. As determined from rawinsonde data, the cold air behind the gust front accounts for the observed surface pressure rise. Calculations confirm that the collision of two fluids produce a nonhydrostatic pressure at the leading edge of the outflow. The equation governing the propagation speed of a density current accurately predicts the movement of the gust front.

Wakimoto, R. M.↗
NASA NTRS1990

Experimental characterization of the effects of pneumatic tubing on unsteady pressure measurements

Advances in aircraft control system designs have, with increasing frequency, required that air data be used as flight control feedback. This condition requires that these data be measured with accuracy and high fidelity. Most air data information is provided by pneumatic pressure measuring sensors. Typically unsteady pressure data provided by pneumatic sensing systems are distorted at high frequencies. The distortion is a result of the pressure being transmitted to the pressure sensor through a length of connective tubing. The pressure is distorted by frictional damping and wave reflection. As a result, air data provided all-flush, pneumatically sensed air data systems may not meet the frequency response requirements necessary for flight control augmentation. Both lab and flight test were performed at NASA-Ames to investigate the effects of this high frequency distortion in remotely located pressure measurement systems. Good qualitative agreement between lab and flight data are demonstrated. Results from these tests are used to describe the effects of pneumatic distortion in terms of a simple parametric model.

Whitmore, Stephen A.↗
NASA NTRSDate not supplied

Application of Lidar-Radar Combined Data Products during the IMPACTS 2020 Field Campaign

The Investigation of Microphysics and Precipitation for Atlantic Coast-Threatening Snowstorms (IMPACTS) is a three-year field campaign investigating the formation and lifecycle of banded, precipitation structures within intense wintertime cyclones impacting the highly-populated northeast United States. Unlike previous campaigns in the region, IMPACTS mission scientists have access to and coordinate the NASA ER-2 and P-3 aircraft to collect observations from both a remote sensing and in-situ perspective, respectively. For IMPACTS, the ER-2 aircraft was equipped with lidar (CPL), radar (CRS, HIWRAP, EXRAD), microwave radiometer (CoSMIR, AMPR) instruments, each with their own unique capabilities and limitations. Our on-going work effort aims to develop IMPACTS lidar and radar merged data products, which can be used to supplement the raw data sources, tease out additional aspects of the mechanisms underpinning wintertime cyclones, and enhance our understanding of microphysical properties in sensor overlap regions. Preliminary merged data products combine CPL lidar with any one of the NASA High Altitude Radar (HAR) radar products (CRS, HIWRAP, EXRAD) and represent these data as both normalized values and translated to reflectivity signal (dB). Continuing work will further refine our merged data product algorithm to provide additional information on hydrometeor species identification, ice crystal habit, and ice-water content, which will help IMPACTS achieve its mission goal of improving microphysical properties retrievals from both airborne and spaceborne platforms.

Stephen D. Nicholls↗
NASA NTRS1977

The LARSYS Educational Package: Instructor's Notes for Use with the Data 100

The LARSYS Educational Package is a set of instructional materials developed to train people to analyze remotely sensed multispectral data using LARSYS, a computer software system. The materials included in this volume have been designed to assist LARSYS instructors as they guide students through the LARSYS Educational Package. All of the materials have been updated from the previous version to reflect the use of a Data 100 Remote Terminal.

Lindenlaub, J. C.↗
NASA NTRS2005

Support for the Harvard University Water Vapor and Total Water Instruments for the 2004 NASA WB57 Middle Latitude Cirrus Experiment

In order to improve our understanding of the role clouds play in the climate system, NASA is investing considerable effort in characterizing clouds with instruments ranging from passive remote sensors on board the EOS platforms, to the forthcoming active remote sensors on Cloudsat and Calipso. These missions, when taken together, have the capacity to advance our understanding of the coupling between various components of the hydrologic cycle and the atmospheric circulation, and hold the additional potential of leading to significant improvements in the characterization of cloud feedbacks in global models. This is especially true considering that several of these platforms will be flown in an identical orbit within several minutes of one another-a constellation of satellites known as the A-Train. The algorithms that are being implemented and developed to convert these new data streams from radiance and reflectivity measurements into geophysical parameters invariably rely on some set of simplifymg assumptions and empirical constants. Uncertainties in these relationships lead to poorly understood random and systematic errors in the retrieved properties. This lack of understanding introduces ambiguity in interpreting the data and in using the global data sets for their intended purposes. In light of this, a series of flights with the W57F was proposed to address certain specific issues related to the basic properties of mid latitude cirrus clouds: the NASA WE357 Middle Latitude Cirrus Experiment ("MidCiX"). The science questions addressed are: 1) Can cloud property retrieval algorithms developed for A-Train active and passive remote sensing measurements accurately characterize the microphysical properties of synoptic and convectively generated cirrus cloud systems? 2) What are the relationships between the cirrus particle mass, projected area, and particle size spectrum in various genre of cirrus clouds? 3) Does the present compliment of state of the art in situ cloud probes provide the level of precision and accuracy needed to develop and validate algorithms and to contribute to our understanding of the characteristics and microphysical processes operating in cirrus clouds?

Anderson, James G.↗