Results for “parameter identification” — Page 77

DOE OSTI2020

Identification of a network of nonlinear interactions as a mechanism triggering the onset of edge localized modes

Edge localized modes (ELMs) remain a critical issue for the lifetime of in-vessel components of fusion reactors such as ITER. We study ELMs triggered when the pedestal parameters are below the peeling-ballooning limit. These ELMs occur while the pedestal recovers after an ELM crash. We identify a mechanism by which a non-linear perturbation involving many active triads—a network of non-linear interactions – leads to the triggering of these ELMs. Each active triad leads to the non-linear transfer of energy between three waves, such that the network of non-linear interactions lead to a transfer of energy between many waves. The triggering of this non-linear perturbation systematically coincides with a pedestal perturbation induced by the neutral beam injection beams and localized near the magnetic surface of safety factor q = 5. Among the non-linear interactions detected during the ELM by a bi-coherence analysis, the most active triad involves a slow frequency that is qualitatively consistent with a geodesic acoustic mode located at the same location, i.e., near the q = 5 surface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1975

Parameter estimation of powered-lift STOL aircraft characteristics including turbulence and ground effects

Longitudinal aerodynamic coefficients are estimated from data recorded during flight tests of a powered-lift STOL aircraft. A comparison is made between the coefficient values determined by the regression and quasilinearization identification techniques from records taken during elevator pulse maneuvers. The results show that for these tests the regression method provides less scatter in coefficient estimates and provides better correlation with the predicted values. Special techniques are developed which allow identification of the coefficients from records taken during landing maneuvers in which the aircraft encounters turbulence while flying in ground effect. Flight test results are presented to illustrate the effects of air turbulence and ground proximity on the estimated coefficient values.

Wingrove, R. C.↗

NASA NTRS2020

Aircraft System Identification from Multisine Inputs and Frequency Responses

The identification of aircraft flight dynamics is often performed using frequency responses, which are nonparametric models that quantify the steady-state magnitude and phase of a dynamic system response to sinusoidal inputs, as a function of frequency. Frequency responses are computed from measured input and output data, and then model parameters, such as stability and control derivatives, are estimated to best fit a parametric model to the empirical frequency response data. The utility of this approach is due to the familiarity of engineers with frequency responses, a number of theoretical and practical advantages under specific conditions, the availability of software packages, and many other reasons.

System identification↗

NASA NTRS1995

Dissipative rendering and neural network control system design

Model-based control system designs are limited by the accuracy of the models of the plant, plant uncertainty, and exogenous signals. Although better models can be obtained with system identification, the models and control designs still have limitations. One approach to reduce the dependency on particular models is to design a set of compensators that will guarantee robust stability to a set of plants. Optimization over the compensator parameters can then be used to get the desired performance. Conservativeness of this approach can be reduced by integrating fundamental properties of the plant models. This is the approach of dissipative control design. Dissipative control designs are based on several variations of the Passivity Theorem, which have been proven for nonlinear/linear and continuous-time/discrete-time systems. These theorems depend not on a specific model of a plant, but on its general dissipative properties. Dissipative control design has found wide applicability in flexible space structures and robotic systems that can be configured to be dissipative. Currently, there is ongoing research to improve the performance of dissipative control designs. For aircraft systems that are not dissipative active control may be used to make them dissipative and then a dissipative control design technique can be used. It is also possible that rendering a system dissipative and dissipative control design may be combined into one step. Furthermore, the transformation of a non-dissipative system to dissipative can be done robustly. One sequential design procedure for finite dimensional linear time-invariant systems has been developed. For nonlinear plants that cannot be controlled adequately with a single linear controller, model-based techniques have additional problems. Nonlinear system identification is still a research topic. Lacking analytical models for model-based design, artificial neural network algorithms have recently received considerable attention. Using their universal approximation property, neural networks have been introduced into nonlinear control designs in several ways. Unfortunately, little work has appeared that analyzes neural network control systems and establishes margins for stability and performance. One approach for this analysis is to set up neural network control systems in the framework presented above. For example, one neural network could be used to render a system to be dissipative, a second strictly dissipative neural network controller could be used to guarantee robust stability.

Gonzalez, Oscar R.↗

DOE OSTI2022

Surface parameters and bedrock properties covary across a mountainous watershed: Insights from machine learning and geophysics

Bedrock property quantification is critical for predicting the hydrological response of watersheds to climate disturbances. Estimating bedrock hydraulic properties over watershed scales is inherently difficult, particularly in fracture-dominated regions. Our analysis tests the covariability of above- and belowground features on a watershed scale, by linking borehole geophysical data, near-surface geophysics, and remote sensing data. We use machine learning to quantify the relationships between bedrock geophysical/hydrological properties and geomorphological/vegetation indices and show that machine learning relationships can estimate most of their covariability. Although we can predict the electrical resistivity variation across the watershed, regions of lower variability in the input parameters are shown to provide better estimates, indicating a limitation of commonly applied geomorphological models. Our results emphasize that such an integrated approach can be used to derive detailed bedrock characteristics, allowing for identification of small-scale variations across an entire watershed that may be critical to assess the impact of disturbances on hydrological systems.

58 GEOSCIENCES↗

DOE OSTI2024

Residual Stress Measurements of Cr-coated Cladding

Accident-tolerant fuel concepts for light-water reactor applications have been developed and tested in diverse research programs around the world. Industry teams have developed coated cladding concepts using different coating application methods, such as physical vapor deposition and coldspraying. Recently, variations in thickness and application method were investigated, and their effects on the microstructure and mechanical properties were reported. The results suggest an increase in performance in an unirradiated state, however, it remains unclear what phenomenon drove this performance. One explanation to this performance is associated with the coating process imparting a residual stress. Residual stress analysis was performed on coatings produced with various process parameters to understand how a thin layer of Cr impacts the mechanical properties after coating application and after simulated operating conditions. The gathered information is intended to address safety concerns or support margin identification related to accident-tolerant fuels and to support subsequent modeling and simulation efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Techno-Economic Evaluation of Electrified Vehicle Options in Drayage Fleets

The electrification of drayage fleets offers potential economic and operational benefits, but the financial viability of electrified vehicles remains sensitive to battery cost, energy price, and fleet usage patterns. While total cost of ownership (TCO) is a useful benchmark, fleet operators and investors are equally concerned with investment performance metrics such as payback period (PB) and Internal Rate of Return (IRR), which better reflect financial risks and investment return timelines. This study develops a unified techno-economic framework that jointly evaluates TCO, PB, and IRR to determine when electrified trucks become cost-effective alternatives to diesel trucks. Building on a previously developed cost modeling tool and using real-world telematics data from a Class 8 drayage fleet at the Port of Savannah, the analysis incorporates projected battery cost trajectories, electricity and diesel price trends, vehicle efficiency improvements, and multiple battery capacities. Parameter ranges reflect widely cited projections and observed drayage-duty-cycle variability. A surrogate-modeling method approximates economic performance across thousands of battery cost–electricity price combinations, enabling high-resolution identification of conditions that achieve TCO parity, acceptable PB thresholds, and target IRR levels. Additionally, the study estimates the evolving share of the fleet that can feasibly electrify over time under multiple economic metrics. This integrated framework offers a novel, data-driven approach to inform risk-aware decision-making for fleet electrification and supports investment planning under evolving cost and operational conditions.

Sun, Ruixiao [ORNL] (ORCID:0000000341768676)↗

NASA NTRS1984

A supercluster catalog

The largest available complete redshift sample of rich clusters of galaxies is used to construct a three-dimensional catalog of superclusters complete to redhsift of about 0.08 or less. The criterion of membership in the catalog is the density enhancement of clusters over the mean density; the catalog is presented for various values of this parameter. The dependence of the identified sample of superclusters on the overdensity is studied, and the sensitivity of the identified superclusters to various quantities and selection procedures is investigated. The validity of the identification procedure is established by comparisons with random catalogs.

Bahcall, N. A.↗

NASA NTRS1988

Dual adaptive control: Design principles and applications

The design of an actively adaptive dual controller based on an approximation of the stochastic dynamic programming equation for a multi-step horizon is presented. A dual controller that can enhance identification of the system while controlling it at the same time is derived for multi-dimensional problems. This dual controller uses sensitivity functions of the expected future cost with respect to the parameter uncertainties. A passively adaptive cautious controller and the actively adaptive dual controller are examined. In many instances, the cautious controller is seen to turn off while the latter avoids the turn-off of the control and the slow convergence of the parameter estimates, characteristic of the cautious controller. The algorithms have been applied to a multi-variable static model which represents a simplified linear version of the relationship between the vibration output and the higher harmonic control input for a helicopter. Monte Carlo comparisons based on parametric and nonparametric statistical analysis indicate the superiority of the dual controller over the baseline controller.

Mookerjee, Purusottam↗

NASA NTRS1990

Real-time diagnostics of the reusable rocket engine using on-line system identification

A model-based failure diagnosis system has been proposed for real-time diagnosis of SSME failures. Actuation, sensor, and system degradation failure modes are all considered by the proposed system. In the case of SSME actuation failures, it was shown that real-time identification can effectively be used for failure diagnosis purposes. It is a direct approach since it reduces the detection, isolation, and the estimation of the extent of the failures to the comparison of parameter values before and after the failure. As with any model-based failure detection system, the proposed approach requires a fault model that embodies the essential characteristics of the failure process. The proposed diagnosis approach has the added advantage that it can be used as part of an intelligent control system for failure accommodation purposes.

Guo, T.-H.↗

NASA NTRS2004

Enhanced Boiling on Micro-Configured Composite Surfaces Under Microgravity Conditions

Two experimental setups: High Heat Flux Pool Boiling Setup and Optical system of Measuring Contact Angle and Spreading Parameters were established and a series of experiments was conducted. The experimental work on the nucleate boiling performance of both Freon-113 and water on the composite surfaces has been finished and the results show that the composite surface with 25% volume fraction of graphite fibers in the copper matrix has the best enhancing performance. Stronger enhancement was obtained for water compared to Freon-113. The wall superheat initiating boiling was reduced 40% and 35% and the heat flux of the nucleate boiling was augmented up to ten times and 6.7 times, respectively. A bubble departure model has been presented to explain the enhancement mechanism of the boiling heat transfer on the composite surfaces. A powerful optical method to measure contact angle and spreading parameters of liquids on solid surfaces, including both transparent and non-transparent substrates, has been developed and successfully used in the measurements for various liquid-solid systems. The experimental work on identification of profiles near three-phase line by laser shadowgraphy method has been finished and the characteristics of the three-phase line for different liquid-solid systems were unveiled, which is very important to understand the mechanism of boiling under microgravity conditions. The four basic patterns of sessile profile were discovered through caustics and caustic-diffraction analysis by applying wave theory in shadowgraphy technology, which contributes to clearly explain the different characteristics of wetting and spreading of various liquids on a solid surface, and therefore to further understand the bubble departure mechanisms. A new working pattern of heat pipes using working fluids with positive surface-tension gradient against temperature was discovered and analyzed, and then the new heat pipe systems using this kind of working fluids have been presented. Two patent devices, i.e. Shadowgraphic Method to Measure Properties of Sessile Drops and Heat Pipe Systems Using New Working Fluids, have been developed; the former has been approved by The United States Patent & Trademark Office and the latter is being examined.

Source record↗

DOE OSTI2023

Towards a Circular Economy for PET Bottles in the US

The United States generates the most plastic waste of any country. Along with that GHG emissions from the global plastic economy are expected to increase to 15% of the global carbon budget by 2050. It is imperative that plastic recycling is made a reality to reduce both plastic pollution in the environment and GHG emissions. A portfolio of end-of-life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different utility and lifetime. Plastic use reduction, reuse and recycling are thus increasingly important, but making informed policy and research decisions within this space can be challenging given the diverse range of available solutions. The novel analysis framework, Plastic Parallel Pathways Platform (4P) has been equipped with consequential life cycle assessment, techno-economic analysis, and a plastic circularity indicator to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) down-cycling to lower-quality resin, closed-loop recycling to food-grade PET bottles, up-cycling to fiber-reinforced plastic (FRP), and conversion to non-plastic products (electricity, oil) on a United States economy-wide basis. Integrating system dynamics into this robust plastics model that already incorporates techno-economics, circularity, and environmental impacts will enable identification of key bottlenecks between manufacturers, waste sorters, and reclaimers that currently prevent rapid decarbonization of the plastics economy. System dynamics (SD) explore the evolution of activities and technologies based on changed macro parameters such as plastic demand and supply, market shifts, and cross-sectoral interactions. This project particularly aims to explore the interplay between, waste collection, plastic waste sorting, recycling, and manufacturing, as well as the effect of plastic bale quality and plastic reuse initiatives on the surrounding process stages. This functionality will facilitate combinatory analysis in which a portfolio of end-of-life pathways are assessed simultaneously, with the exact makeup of that portfolio affected by parameters such as technology scales, resource constraints, and waste mitigation efforts. Integrating SD with the 4P framework enables analyzing the effect of increased revenue and reinvestment into improving process efficiencies, sorting and collection quantities. Through that, market effects of increased recycled resin availability can be studied for the plastics systems model for the US. The results will help identify technical or economic bottlenecks that currently limit efforts to decarbonize the U.S. plastics economy.

circular economy↗

DOE OSTI2024

Towards a Circular Economy for PET Bottles in the U.S. - 4P Model

The United States generates the most plastic waste of any country. Along with that GHG emissions from the global plastic economy are expected to increase to 15% of the global carbon budget by 2050. It is imperative that plastic recycling is made a reality to reduce both plastic pollution in the environment and GHG emissions. A portfolio of end-of-life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different utility and lifetime. Plastic use reduction, reuse and recycling are thus increasingly important, but making informed policy and research decisions within this space can be challenging given the diverse range of available solutions. The novel analysis framework, Plastic Parallel Pathways Platform (4P) has been equipped with consequential life cycle assessment, techno-economic analysis, and a plastic circularity indicator to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) down-cycling to lower-quality resin, closed-loop recycling to food-grade PET bottles, up-cycling to fiber-reinforced plastic (FRP), and conversion to non-plastic products (electricity, oil) on a United States economy-wide basis. Integrating system dynamics into this robust plastics model that already incorporates techno-economics, circularity, and environmental impacts will enable identification of key bottlenecks between manufacturers, waste sorters, and reclaimers that currently prevent rapid decarbonization of the plastics economy. System dynamics (SD) explore the evolution of activities and technologies based on changed macro parameters such as plastic demand and supply, market shifts, and cross-sectoral interactions. This project particularly aims to explore the interplay between, waste collection, plastic waste sorting, recycling, and manufacturing, as well as the effect of plastic bale quality and plastic reuse initiatives on the surrounding process stages. This functionality will facilitate combinatory analysis in which a portfolio of end-of-life pathways are assessed simultaneously, with the exact makeup of that portfolio affected by parameters such as technology scales, resource constraints, and waste mitigation efforts. Integrating SD with the 4P framework enables analyzing the effect of increased revenue and reinvestment into improving process efficiencies, sorting and collection quantities. Through that, market effects of increased recycled resin availability can be studied for the plastics systems model for the US. The results will help identify technical or economic bottlenecks that currently limit efforts to decarbonize the U.S. plastics economy.

carbon↗

DOE OSTI2024

Towards a Circular Economy for PET Bottles in the U.S. - 4P Framework

The United States generates the most plastic waste of any country. Along with that GHG emissions from the global plastic economy are expected to increase to 15% of the global carbon budget by 2050. It is imperative that plastic recycling is made a reality to reduce both plastic pollution in the environment and GHG emissions. A portfolio of end-of-life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different utility and lifetime. Plastic use reduction, reuse and recycling are thus increasingly important, but making informed policy and research decisions within this space can be challenging given the diverse range of available solutions. The novel analysis framework, Plastic Parallel Pathways Platform (4P) has been equipped with consequential life cycle assessment, techno-economic analysis, and a plastic circularity indicator to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) down-cycling to lower-quality resin, closed-loop recycling to food-grade PET bottles, up-cycling to fiber-reinforced plastic (FRP), and conversion to non-plastic products (electricity, oil) on a United States economy-wide basis. Integrating system dynamics into this robust plastics model that already incorporates techno-economics, circularity, and environmental impacts will enable identification of key bottlenecks between manufacturers, waste sorters, and reclaimers that currently prevent rapid decarbonization of the plastics economy. System dynamics (SD) explore the evolution of activities and technologies based on changed macro parameters such as plastic demand and supply, market shifts, and cross-sectoral interactions. This project particularly aims to explore the interplay between, waste collection, plastic waste sorting, recycling, and manufacturing, as well as the effect of plastic bale quality and plastic reuse initiatives on the surrounding process stages. This functionality will facilitate combinatory analysis in which a portfolio of end-of-life pathways are assessed simultaneously, with the exact makeup of that portfolio affected by parameters such as technology scales, resource constraints, and waste mitigation efforts. Integrating SD with the 4P framework enables analyzing the effect of increased revenue and reinvestment into improving process efficiencies, sorting and collection quantities. Through that, market effects of increased recycled resin availability can be studied for the plastics systems model for the US. The results will help identify technical or economic bottlenecks that currently limit efforts to decarbonize the U.S. plastics economy.

circular economy↗

DOE OSTI2016

High Energy Neutrino Physics with NOvA

Knowledge of the position of energy deposition in “hit” detector cells of the NOvA neutrino detector is required by algorithms for pattern reconstruction and particle identification necessary to interpret the raw data. To increase the accuracy of this process, the majority of NOvA's 350 000 far detector cell shapes, including distortions, were measured as they were constructed. Using a special laser scanning system installed at the site of the NOvA far detector in Ash River, MN, we completed algorithmic development and measured shape parameters for the far detector. The algorithm and the measurements are “published” in NOνA’s document database (doc #10389, “Cell Center Finder for the NOνA Far Detector Modules”).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS1985

A cluster analysis method for identification of subpopulations of cells in flow cytometric list-mode arrays

A specialized program was developed for flow cytometric list-mode data using an heirarchical tree method for identifying and enumerating individual subpopulations, the method of principal components for a two-dimensional display of 6-parameter data array, and a standard sorting algorithm for characterizing subpopulations. The program was tested against a published data set subjected to cluster analysis and experimental data sets from controlled flow cytometry experiments using a Coulter Electronics EPICS V Cell Sorter. A version of the program in compiled BASIC is usable on a 16-bit microcomputer with the MS-DOS operating system. It is specialized for 6 parameters and up to 20,000 cells. Its two-dimensional display of Euclidean distances reveals clusters clearly, as does its 1-dimensional display. The identified subpopulations can, in suitable experiments, be related to functional subpopulations of cells.

Li, Z. K.↗

NASA NTRS1993

A new method for the identification of non-Gaussian line profiles in elliptical galaxies

A new parameterization for the line profiles of elliptical galaxies, the Gauss-Hermite series, is proposed. This approach expands the line profile as a sum of orthogonal functions which minimizes the correlations between the errors in the parameters of the fit. This method also make use of the fact that Gaussians provide good low-order fits to observed line profiles. The method yields measurements of the line strength, mean radial velocity, and the velocity dispersion as well as two extra parameters, h3 and h4, that measure asymmetric and symmetric deviations of the line profiles from a Gaussian, respectively. The new method was used to derive profiles for three elliptical galaxies which all have asymmetric line profiles on the major axis with symmetric deviations from a Gaussian. Results confirm that elliptical galaxies have complex structures due to their complex formation history.

Van Der Marel, Roeland P.↗

NASA NTRSDate not supplied

Frequency Domain Quasi Maximum Likelihood Identification of Low Order Aeroservoelastic Models from Flight-Test Data

In this paper a quasi maximum likelihood method for estimating a low order model of a flexible vehicle has been developed and demonstrated. The quasi maximum likelihood method uses a large number of sensors to estimate the parameters and covariance in a method consistent with the maximum likelihood filter-error method. The cost function has been defined in a frequency domain to improve computational efficiency and to enable estimation of an unstable plant. The method has been demonstrated using flight data from the National Aeronautics and Space Administration X-56A Multi-Utility Technology Testbed flex wing tests, which include unstable flutter modes. The method was able to effectively estimate the frequency and damping of the dynamics of the aircraft and generate a transfer function that is useful for control system evaluations.

Jeffrey Ouellette↗