Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrode interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Nanoparticle Surface Passivation Strategies to Improve the Cycle and Calendar Lifetime of Silicon Anodes in Standard Carbonate Electrolytes

Silicon Lithium alloys (SiLix) as the anode active material in a Li-Ion battery configuration offer possible energy densities paralleled only by pure lithium metal. However, the extreme mechanical deformation of alloying and dealloying SiLix through charge/discharge cycles paired with the highly reactive interface of SiLix which generates an interfacial layer known as the solid-electrolyte-interphase are large barriers to industrial adoption of high-silicon-content negative electrodes. Moreover, these challenges are magnified when the thickness of the electrode is brought to relevant levels (>3 mg/cm2). Here, I describe our efforts to address these challenges by utilizing single-nanometer-scale silicon nanoparticles to reduce capacity fade related to mechanical failure. I also detail our efforts to modify the silicon surface through interfacial chemical engineering strategies to passivate the silicon surface. This development three different majority silicon electrodes (50-74 wt%) to achieve cycle capacity retention of greater than 73% through 1000 charge/discharge cycles against capacity-matched NMC-based cathodes and calendar lifetimes greater than one year. This research is a part of the multi-national lab Silicon Consortium Project.

anodes↗

Practically Accessible All-Solid-State Batteries Enabled by Organosulfide Cathodes and Sulfide Electrolytes

The combination of organic electrode materials and sulfide electrolytes is expected to enable the development of all-solid-state organic batteries featuring high energy density and long-term sustainability. In this work, thiuram hexasulfide is reported as a low-cost and high-capacity organic cathode for solid-state batteries based on sulfide electrolytes, delivering a capacity of ~600 mAh g -1 and retaining 80.8 % capacity after 500 cycles. An electrochemically reversible change of the cathode interface was revealed upon cycling. Full cell displays an oscillating stress change up to 0.6 MPa during cycling, predominated by the anode side. The energy density is 1140 Wh kg -1 at the material level and 376 Wh kg -1 at the electrode level, which are among the best-reported organic cathodes to date. A high areal capacity of 10.4 mAh cm -2 is reached with a high mass loading cathode. A dry-film approach is further explored to manufacture sheet-type cells. Free-standing electrolyte film is merely ~48 μm thick and demonstrates an ultralow areal resistance of 3.9 Ω cm 2 , significantly boosts the cell-level energy density and reduces the cell internal resistance.

25 ENERGY STORAGE↗

Iterative redox activation promotes interfacial synergy in an Ag/Cu x O catalyst for oxygen reduction

In this study, an iterative electrochemical activation process is demonstrated to maximize the interface between Ag and Cu x O. Morphological reconstruction and phase transformation of Cu x O occurs through the iterative electrochemical redox reaction, as indicated by energy-dispersive spectroscopy and X-ray photoelectron spectroscopy. The activated Ag/Cu x O/C catalysts exhibits enhanced oxygen reduction reaction performance, with an onset potential of 0.86 V vs. the reversible hydrogen electrode, a Tafel slope of 46mV dec -1 , and a high stability as compared to Ag/C. A mechanistic study using density functional theory shows that the weakened binding energy of the OH intermediate, originating from the charge transfer from Ag to Cu x O, improves the ORR activity at the interface sites of the Ag/Cu x O electrocatalysts. Ag/Cu x O shows a higher limiting potential of 0.14V for interface sites than isolated Ag nanoparticles. The interfacial charge transfer between Ag and CuO is verified experimentally.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conformal hetero-electrolyte interface between soft oxyhalides and garnet enables low-pressure lithium-reservoir-free solid-state batteries

The operation of solid-state batteries with a lithium metal anode and a high voltage cathode requires solid electrolytes (SEs) that are chemically stable with lithium, have a wide electrochemical window, and accommodate volume changes in the electrodes. Unfortunately, no SE has exhibited satisfactory mechanical and electrochemical properties that fit these requirements to date. Dual solid electrolyte systems that use a different SE for the anolyte and catholyte present a viable solution. Here, we focus on oxyhalide SEs that demonstrate superior ionic conductivity and cathode compatibility, where their lithium metal reactivity and poor reduction stability can be resolved using a lithium garnet (Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 , LLZTO) separator. Nonetheless, this imposes a new hetero-electrolyte (H-E) interface at the anolyte|catholyte contact that defines the ion transport across the boundary. We report its promising properties, which are deconvoluted from the electrical measurements of bilayer symmetric cells, for three representative oxyhalide catholytes, LiNbOCl 4 , LiTaOCl 4 , and Li 3 Al 3 O 2 Cl 8 . Pressure-dependent measurements reveal that the relative softness of the oxyhalides (hardness ≤0.4 GPa) enables H-E resistances lower than 150 Ω cm 2 at 2–3 MPa. Mesoscale modelling reveals that the transfer-active contact area of oxyhalides with LLZTO is about 2–3-fold higher than that of argyrodite, Li 6 PS 5 Cl. The low H-E resistance of the LiNbOCl 4 |Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 dual electrolyte enables the cycling of a Li|LiNi 0.82 Mn 0.07 Co 0.11 O 2 full cell with a high discharge capacity (200 mA h g −1 ) at 60 °C and ∼7 MPa. Importantly, we demonstrate a Li-reservoir-free full cell with high Coulombic efficiency (>99.5%) and capacity at 1 MPa using this approach coupled with a garnet-silver interlayer.

Palmer, Max [University of California, Santa Barba↗

Effect of Pressurization on Solid Oxide Cell Oxygen Electrodes: the Role of PrO x Nanoparticle Infiltration

Pressurization of solid oxide cells improves performance by reducing electrode polarization resistance (R P ) and facilitates system integration with balance of plant components such as pressurized storage tanks. However, there are few reports on pressurization effects for electrodes designed for low-temperature operation and utilizing infiltrated catalysts. Here we report an electrochemical impedance spectroscopy study of high performing oxygen electrode materials, SrTi 0.3 Fe 0.63 Co 0.07 O 3-∂ (STFC) and PrO x infiltrated STFC, for oxygen partial pressures ($p$ $o$ 2 ) from 0.1 to 8 atm and temperatures from 550 to 650 °C. decreases more with pressurization for STFC:PrO x , fitting well to with an exponent n~0.3, compared to n~0.25 for STFC. The combination of PrO x infiltration and pressurization yields a substantial R P decrease, e.g., at 600 °C by ~7 times from 0.36 Ω cm 2 at $p$ $o$ 2 = 0.2 atm for STFC to 0.055 Ω cm 2 at $p$ $o$ 2 = 4 atm for STFC:PrO x . Here, a transmission-line-based circuit model impedance fit reveals that the significant oxygen surface reaction (R surf ) resistance contribution decreases substantially with PrO x infiltration; and its $p$ $o$ 2 dependence become more pronounced, with n increasing from ~0.25 to ~0.5. R surf for STFC:PrO x decreases so much at elevated $p$ $o$ 2 that the electrode/electrolyte interface resistance dominates.

25 ENERGY STORAGE↗

Influence of GaAs surface termination on GaSb/GaAs quantum dot structure and band offsets

We have investigated the influence of GaAs surface termination on the nanoscale structure and band offsets of GaSb/GaAs quantum dots (QDs) grown by molecular-beam epitaxy. Transmission electron microscopy reveals both coherent and semi-coherent clusters, as well as misfit dislocations, independent of surface termination. Cross-sectional scanning tunneling microscopy and spectroscopy reveal clustered GaSb QDs with type I band offsets at the GaSb/GaAs interfaces. We discuss the relative influences of strain and QD clustering on the band offsets at GaSb/GaAs interfaces.

36 MATERIALS SCIENCE↗

Tuning the interfacial spin-orbit coupling with ferroelectricity

Detection and manipulation of spin current lie in the core of spintronics. Here we report an active control of a net spin Hall angle, θ SHE (net), in Pt at an interface with a ferroelectric material PZT (PbZr 0.2 Ti 0.8 O 3 ), using its ferroelectric polarization. The spin Hall angle in the ultra-thin Pt layer is measured using the inverse spin Hall effect with a pulsed tunneling current from a ferromagnetic La 0.67 Sr 0.33 MnO 3 electrode. The effect of the ferroelectric polarization on θ SHE (net) is enhanced when the thickness of the Pt layer is reduced. When the Pt layer is thinner than 6 nm, switching the ferroelectric polarization even changes the sign of θ SHE (net). This is attributed to the reversed polarity of the spin Hall angle in the 1 st -layer Pt at the PZT/Pt interface when the ferroelectric polarization is inverted, as supported by the first-principles calculations. These findings suggest a route for designing future energy efficient spin-orbitronic devices using ferroelectric control.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Three-Dimensional Mathematical Model of Oxygen Transport Behavior in Electroslag Remelting Process

A transient three-dimensional model has been proposed to investigate the oxygen transport behavior in electroslag remelting process. The electromagnetism, heat transfer, multiphase flow, and species transport were calculated simultaneously by finite volume method. The volume of fluid approach was adopted to trace the metal–slag–air three-phase flow. Based on the necessary thermodynamics of oxygen transport behavior, a kinetic model was established to predict the mass source terms in species transport equation. The kinetic correction factor was proposed to account for the effect of the oxide scale formed on the electrode on the FeO content in slag. Finally, the effect of applied current on the oxygen transfer was studied. The predicted result agrees well with the measured data when the kinetic correction factor is set to be 0.5. The temperature distribution that affects the thermodynamics differs at the interfaces. The oxygen in air is absorbed into slag due to the oxidation at the slag/air interface. The Fe{sub 2}O{sub 3} in slag and the oxide scale contribute to the increase of FeO content in slag, and the latter one plays the leading role. The oxygen transfer from slag to metal mainly occurs during the formation of the droplet at the slag/metal droplet interface. With the current increasing from 1200 to 1800 A, the oxygen content increases from 76.4 to 89.8 ppm, and then slightly declines to 89.2 ppm when the current increases to 2100 A.

36 MATERIALS SCIENCE↗

Real-time interface investigation on degradation mechanism of organic light-emitting diode by in-operando X-ray spectroscopies

Understanding the chemical evolution at the interface of organic light-emitting diodes (OLEDs) under working conditions is critical for addressing device failure and further improving performance. In this work, an in-operando approach was developed employing synchrotron-based X-ray absorption spectroscopy (XAS) to investigate the electronic structures and chemical degradation mechanisms of a model tris(8-hydroxyquinoline) aluminum (Alq 3 )-based OLED device under working condition. The results identify that Mg atoms from the electrode migrate into the Alq 3 organic layer under a potential bias and replace Al atom sites, forming the unstable Mgq 3 species which lead to device degradation. Here, the findings from the classic and simple model device elucidate the degradation mechanisms occurred at the interface of OLED devices, which may facilitate the development of more efficient and stable OLED devices with complex structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct Observation of Photoexcited Charge Carrier Dynamics and Electrostatic Fields at Photocatalytic Semiconductor/liquid Interfaces

Photoelectrochemical conversion of solar energy to fuels at semiconductor-liquid interfaces involves a complex set of processes, which include band bending, built-in electric fields, surface recombination of photoexcited carriers, and ultimately charge transfer to the ions in solution, in which the electrostatic fields within the depletion region of the semiconductor plays an important role. There are loss mechanisms associated with each of these key components in the overall photoelectrochemical conversion efficiency. Direct probe of these elementary processes is key to the rational improvement of photoeletrochemical cells and electrodes. In this collaborative project, Tianquan Lian at Emory University, Steve Cronin at University of Southern California and their students and postdoctoral fellows carried out a series of studies that are aimed at direct observation of photoexcited charge carrier dynamics at photocatalytic semiconductor/liquid interfaces. The collaborative work led to the development of transient reflectance spectroscopy as a tool for in situ probing of carrier dynamics in planar photoelectrode/electrode interface; and the demonstration that this tool can be used to study oxide protected GaP to identify key efficiency limiting factors in these photoelectrodes. This work has led to the development a tool for in situ probing of carrier dynamics in planar photoelectrodes, which will facilitate the mechanistic study of photoelectrochemical cells. This work informs the development of better photoelectrode materials for solar water splitting and CO 2 reduction. This work has contributed to the training of three PhD students in the area of photoelectrochemistry, ultrafast spectroscopy and solar energy conversion

14 SOLAR ENERGY↗

Intrinsic Ion Transport Properties of Block Copolymer Electrolytes

Knowledge of intrinsic properties is of central importance for materials design and assessing suitability for specific applications. Self-assembling block copolymer electrolytes (BCEs) are of great interest for applications in solid-state energy storage devices. A fundamental understanding of ion transport properties, however, is hindered by the difficulty in deconvoluting extrinsic factors, such as defects, from intrinsic factors, such as the presence of interfaces between the domains. Here, we quantify the intrinsic ion transport properties of a model BCE system consisting of poly(styrene-block-ethylene oxide) (SEO) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt using a generalizable strategy of depositing thin films on interdigitated electrodes and self-assembling fully connected parallel lamellar structures throughout the films. Comparison between conductivity in homopolymer poly(ethylene oxide) (PEO)-LiTFSI electrolytes and the analogous conducting material in SEO over a range of salt concentrations (r, molar ratio of lithium ion to ethylene oxide repeat units) and temperatures reveals that between 20% and 50% of the PEO in SEO is inactive. Using mean-field theory calculations of the domain structure and monomer concentration profiles at domain interfaces-both of which vary substantially with salt concentration-the fraction of inactive PEO in the SEO, as derived from conductivity measurements, can be quantitatively reconciled with the fraction of PEO that is mixed with greater than a few volume percent of polystyrene. Despite the detrimental interfacial effects for ion transport in BCEs, the intrinsic conductivity of the SEO studied here (ca. 10 -3 S/cm at 90 degrees C, r = 0.085) is an order of magnitude higher than reported values from bulk samples of similar molecular weight SEO (ca. 10 -4 S/cm at 90 degrees C, r = 0.085). Finally, this work provides motivation and methods for pursuing improved BCE chemical design, interfacial engineering, and processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Observing the Electrochemical Oxidation of Co Metal at the Solid/Liquid Interface Using Ambient Pressure X-ray Photoelectron Spectroscopy

Some rcent advances of ambient pressure X-ray photoelectron spectroscopy (AP-XPS) have enabled the chemical composition and the electrical potential profile at a liquid/electrode interface under electrochemical reaction conditions to be directly probed. In this work, we apply this operando technique to study the surface chemical composition evolution on a Co metal electrode in 0.1 M KOH aqueous solution under various electrical biases. It is found that an ~12.2 nm-thick layer of Co(OH) 2 forms at a potential of about -0.4 V Ag/AgCl , and upon increasing the anodic potential to about +0.4 V Ag/AgCl , this layer is partially oxidized into cobalt oxyhydroxide (CoOOH). A CoOOH/Co(OH) 2 mixture layer is formed on the top of the electrode surface. Finally, the oxidized surface layer can be reduced to Co0 at a cathodic potential of -1.35 VAg/Cl. Our observations indicate that the ultrathin layer containing cobalt oxyhydroxide is the active phase for oxygen evolution reaction (OER) on a Co electrode in an alkaline electrolyte, consistent with previous studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular Junctions: Control of the Energy Gap Achieved by a Pinning Effect

Single-molecule junctions are the constitutive components of molecular electronics circuits. For any potential application, the energy gap in the junction, i.e., the accumulated energy difference between the electrode Fermi level and the two frontier energy levels of the molecule, is a key property. In this study, using the nonequilibrium Green’s function coupled to the density functional theory framework (NEGF-DFT) method, we show that the gap of the molecule inserted between electrodes can differ largely from the gap of the same molecule, at the isolated level. It can be widely compressed by tuning the alignment mechanism at each metal/molecule interface. In the context of molecular rectification, we show that this mechanism relates to the pinning effect. We discuss the different parameters affecting the compression of the gap and its efficiency. Interestingly, we find that the structure both of the molecule and of the anchoring group plays an important role. Finally, we investigate the evolution of these features out-of-equilibrium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ammonium Additives to Dissolve Lithium Sulfide through Hydrogen Binding for High-Energy Lithium–Sulfur Batteries

In rechargeable Li-S batteries, the uncontrollable passivation of electrodes by highly insulating Li2S limits sulfur utilization, increases polarization and decreases cycling stability. Dissolving Li2S in organic electrolyte is a facile solution to maintain the active reaction interface between electrolyte and sulfur cathode, and thus address the above issues. Herein, ammonium salts are demonstrated as effective additives to promote the dissolution of Li2S to 1.25 M in DMSO solvent at room temperature. NMR measurements show that the strong hydrogen binding effect of N-H groups plays a critical role in dissolving Li2S by forming complex ligands with S2- anions coupled with the solvent’s solvating surrounding. Ammonium additives in electrolyte can also significantly improve the oxidation kinetics of Li2S, therefore enables the direct use of Li2S as cathode material in Li-S battery system in the future. This provides a new approach to manage the solubility of lithium sulfides through cation coordination with sulfide anion.

Environmental Molecular Sciences Laboratory↗

Operando Freezing Cryogenic Electron Microscopy of Active Battery Materials

Abstract Understanding structural and chemical evolution of battery materials during operation is critical to achieving safe, efficient, and long-lasting energy storage. Cryogenic electron microscopy (cryo-EM) has become a valuable tool in battery characterization, leveraging low temperatures to improve stability of sensitive materials under electron beam irradiation. However, typical cryo-EM sample preparations leave extended time between the electrochemical point of interest and ex situ freezing of samples, during which active structures may relax, degrade, or otherwise evolve. Here, we detail a method for operando freezing cryo-EM to preserve and characterize native electrode and interfacial structures that arise during battery cycling, based on an operando plunge freezer and cold sample removal process. We validate the method on multiple electrode materials and quantify and discuss the freezing rate achieved. Operando freezing cryo-EM can be used to directly visualize transient features that arise at active electrochemical interfaces, to enable deeper understanding of structural evolution and interfacial chemistry in batteries and other electrochemical systems.

25 ENERGY STORAGE↗