SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Drop length necessary to convert molten silicon to shot reduced by proposed new process. Conversion of silicon from powder or chunks to shot often simplifies processing. Shot is more easily handled in most processing equipment. Drops of liquid silicon fall through protective cloud of argon, then through rapidly cooling bath of methanol, where they quickly turn into solid shot.
The chamber is a thermal gradient diffusion type with the upper plate at room temperature and the lower plate thermoelectrically cooled. The light from a 25W projector bulb is focused in a beam of approximations 1x3 mm in the central part of the chamber. The light scattered by drops is viewed in the forward direction (40 deg) by a microscope and a sensitive photodetector. Experiments were performed to relate the peak output from the photocell with the maximum number of drops in the beam recorded photographically. The microscope is used to check the calibration at low concentrations of CCN. The results of the experiments and the performance of the counter are reported.
The effect of hydrodynamic, aerodynamic and liquid surface forces on the mean drop diameter of water sprays that are produced by the breakup of nonswirling and swirling water sheets in quiescent air and in airflows similar to those encountered in gas turbine combustors is investigated. The mean drop diameter is used to characterize fuel sprays and it is a very important factor in determining the performance and exhaust emissions of gas turbine combustors.
Experiments were conducted on bubble migration in rotating liquid bodies contained in a sphere. Experiments were initiated on the migration of a drop in a slightly less dense continuous phase contained in a rotating sphere. A refined apparatus for the study of thermocapillar flow in a glass melt was built, and data were acquired on surface velocities in the melt. Similar data also were obtained from an ambient temperature fluid model. The data were analyzed and correlated with the aid of theory. Data were obtained on flow velocities in a pendant drop heated from above. The motion in this system was driven principally by thermocapillarity. An apparatus was designed for the study of volatilization from a glass melt.
The flow, atomization and spreading of flashing injector flowing liquids containing dissolved gases (jet/air) as well as superheated liquids (Freon II) were considered. The use of a two stage expansion process separated by an expansion chamber, ws found to be beneficial for flashing injection particularly for dissolved gas systems. Both locally homogeneous and separated flow models provided good predictions of injector flow properties. Conventional correlations for drop sizes from pressure atomized and airblast injectors were successfully modified, using the separated flow model to prescribe injector exit conditions, to correlate drop size measurements. Additional experimental results are provided for spray angle and combustion properties of sprays from flashing injectors.
This paper discusses the parachute subsystem used on an atmospheric entry probe that will descend through the clouds of Jupiter. The entry probe is a part of the Galileo Project to be launched in 1985 aboard the Space Shuttle; the entry probe will encounter the planet in 1988. The parachute subsystem consists of a pilot parachute and a main parachute, and both are of conventional conical ribbon design. Key considerations in the design of the parachutes and a summary of the parachute subsystem test program, which includes two air drop tests and a systems drop test (balloon launched), are presented.
Measurements in the 0.1-2.5 micron range are presented for the reflectance spectra of the frosts of several volatiles pertinent to the study of comet nuclei. The frost spectra have distinctive features permitting their identification by spectroscopic reflectance remote sensing, notably in the far UV. It is found that: (1) H2O has a minimum at 0.16 microns and a maximum at 0.13 microns; (2) CO2 has minima near 0.21, 0.18 and 0.125 microns, with maxima at 0.19, 0.135 and 0.120 microns; (3) NH3 is bright at wavelengths longer than 0.21 microns, where reflectance drops to a value of only a few per cent at shorter wavelengths; (4) SO2 has a sharp drop at 0.32 microns, with a minimum at 0.18 microns and a maximum at 0.13 microns. The features in the frost spectra largely correspond to absorption line bands in the gas phase.
Flashing injection involves expanding a fluid through an injector until a supersaturated state is reached, causing a portion of the fluid to flash to a vapor. This investigation considered the flow, atomization and spreading properties of flashing injectors flowing liquids containing dissolved gases (Jet A/air) as well as superheated liquids (Freon 11). The use of a two stage expansion process, separated by an expansion chamber, was found to be beneficial for good atomization properties of flashing injection - particularly for dissolved gas systems. Both locally homogeneous and separated flow models provided good predictions of injector flow properties. Conventional correlations for drop sizes from pressure atomized and airblast injectors were successfully modified, using the separated flow model to prescribe injector exit conditions, to correlate drop size measurements. Additional experimental results are provided for spray angle and combustion properties of sprays from flashing injectors.
It is suggested that small energy discharges of low differential voltage that are associated with internal buried charge may be an important mechanism by which sorted electrostatic energy is released from dielectrics on board orbiting spacecraft. The evidence from space given by Stevens (1980) is noted, and the laboratory experimental evidence of Frederickson is cited to demonstrate that discharges occur under circumstances with no external potential drop. Previous calculations indicating that significant internal electric fields can exist in dielectrics charged with multiple-kilovolt electron beams under conditions involving little or no external potential drop are reviewed. Attention is given to the internal discharge mechanism of Meulenberg (1976), and new calculations suggesting that the space environment is conducive to the formation of the conditions required by this mechanism are presented. Experimental procedures for checking the suggestions made are developed.
An inverted-V auroral arc structure plasma-kinetic model is extended to phenomenologically include the effects of electrostatic turbulence, with k-parallel/k-perpendicular being much less than unity. It is shown that, unless plasma sheet ions are very much more energetic than the electrons, anomalous resistivity is not a large contributor to parallel electrostatic potential drops, since the support of the observed potential drop requires a greater dissipation of energy than can be provided by the plasma sheet. Wave turbulence can, however, be present, with the ion cyclotron turbulence levels suggested by the ion resonance broadening saturation mechanism of Dum and Dupree (1970) being comparable to those observed on auroral field lines. The diffusion coefficient and net growth rate are much smaller than estimates based solely on local plasma properties.
Absolute spectrophotometric observations of 19 quasars with redshifts greater than 2.66 are reported. Observations were made with a multichannel spectrometer covering wavelengths from 3200 to 10000 A at low resolution and allowing accurate absolute fluxes to be determined for continuum and emission lines. Analysis of energy distribution measurements indicates the continuum spectral index redward of Lyman alpha to vary from -0.2 to -1.2. Average flux levels drop by 29% between Lyman alpha and Lyman beta, and by a further 10% below Lyman beta, and a drop or change of slope occurs near the Lyman limit, all of which are attributed to absorbing clouds at different redshifts. Estimations of a covering factor of 0.08 based on the Lyman alpha and He II 1640 lines are consistent with the production of these lines by recombination. The measured emission lines are observed to have intensities proportional to the continuum flux, with the exception of C IV, which shows the luminosity effect similar to that found by Baldwin (1977).
Linear shift-invariant spatial filtering is applied to inversion of radiometric measurements of the earth in both polarizations at the following frequencies: 6.6, 10.7, 18, 21, and 37 GHz. For purposes of radiative transfer calculations at these frequencies, the state of the ocean-atmosphere system is described by a seven-parameter model. The parameters are near-surface wind speed, sea surface temperature, integrated water vapor mass, scale height of water vapor in an exponential distribution, integrated liquid water mass, height of the liquid water, and characteristic drop radius in a Best (1950) drop size distribution. Also described is a spatial filtering algorithm by means of which geophysical parameters are retrieved from measurements made over the ocean by the scanning multichannel microwave radiometer on the Nimbus 7 satellite. The parameters here are near-surface wind speed, sea surface temperature, rain rate, integrated atmospheric water vapor content, and integrated liquid water content (including rain).
The incorporation in the 13.5 GHz Seasat-type radar altimeter of a mode to measure rain rate is investigated. Specifically, an algorithm is developed relating the echo power at the various range bins, to the rain rate taking into consideration Mie scattering and path attenuation. The dependence of the algorithm on rain drop size distribution and nonuniform rain structure are examined and associated uncertainties defined. A technique for obtaining drop size distribution through the measurements of power at the top of the raincell and power difference through the cell also is investigated together with an associated error analysis. A description of the minor hardware modifications to the basic Seasat design is given for implementing the rain measurements.
Helicopter drop tests were made of models of the Pioneer Venus probe descent configurations to characterize their unsteady forces and angular dynamics in equilibrium descent. The axial and normal forces were found to be unsteady in magnitude by about 10 and 5% of the mean axial force, respectively. A cycle of the axial variation takes place in flight distances of from 15 to 40 diameters. The unsteadiness almost certainly is associated with the wake. Angular motions which do not converge to zero angle of attack even in very long duration descent are excited by the unsteady pitching moments. The nearly spherical large probe model was aerodynamically more unsteady than the round-nosed conical small probe model. Data returned from Venus by the Pioneer Venus probes show unsteady axial forces and angular motions similar to those seen in the drop tests.
The theory of acoustic propagation in strained media is examined, with particular emphasis on rod (bolt) geometries. The continuous wave (CW) approach is the basis of the study, and the theory is developed from a frequency domain analysis standpoint in order to obtain an applied stress/normalized frequency shift relationship. CW measurements may be influenced by such factors as propagation effects, mode conversion, frequency, material properties, and geometry. After the first loading cycle, axial stress measurements for a preloading with an initial frequency of 4.995 36 MHz dropped to 4.989 19 MHz, indicating a 6.17 kHz change. CW and pseudo-CW ultrasonic techniques are found to be reliable for axial stress measurements, and acoustic attenuation measurements correlated to residual stress fields may possibly involve transducer phase cancellation. It is thus concluded that signal drop is an artifact of the transducer directivity, rather than an actual acoustic power decrease.
In large area, low cost solar cells of any type, the contact and grid structure metallization is an important factor which has an effect on the efficiency of the solar cell and its reliability. The present investigation is concerned with aspects of solar cell efficiency. An optimized metallization design leads to minimum total power loss, which is related to a simultaneous minimization of ohmic voltage drops and of shading of the front surface of the cell by the overlaid metal. The requirements regarding the design for a low-loss metallization pattern for the front surface of large area solar cells are represented by a set of design rules listed in a table. The total shading and voltage drop on such cells can be held to about 5%. However, not every metallization process is suited for meeting the requirements of the low-cost design. The low losses can be achieved only by use of several bus lines containing a bulk conductor, such as a wire.
Feedback system assures production of silicon shot of uniform size. Breakup of silicon stream into drops is controlled, in part, by varying frequency of vibrations imparted to stream by ultrasonic transducer. Drop size monitored by photodetector. Control method particularly advantageous in that constant size is maintained even while other process variables are changed deliberately or inadvertently. Applicable to materials other than silicon.
A study was performed by AiResearch Manufacturing Company, a division of The Garrett Corporation, on the development a high-temperature ceramic heat exchanger element to be integrated into a solar receiver producing heated air. A number of conceptual designs were developed for heat exchanger elements of differing configuration. These were evaluated with respect to thermal performance, pressure drop, structural integrity, and fabricability. The final design selection identified a finned ceramic shell as the most favorable concept. The shell is surrounded by a larger metallic shell. The flanges of the two shells are sealed to provide a leak-tight pressure vessel. The ceramic shell is to be fabricated by an innovative combination of slip casting the receiver walls and precision casting the heat transfer finned plates. The fins are bonded to the shell during firing. The unit is sized to produce 2150 F ar at 2.7 atm pressure, with a pressure drop of about 2 percent of the inlet pressure. This size is compatible with a solar collector providing a receiver input of 85 kw(th). Fabrication of a one-half scale demonstrator ceramic receiver has been completed.