SEARCH · Engineering Papers

Results for “direct current”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Preliminary study of a large span-distributed-load flying-wing cargo airplane concept

An aircraft capable of transporting containerized cargo over intercontinental distances is analyzed. The specifications for payload weight, density, and dimensions in essence configure the wing and establish unusually low values of wing loading and aspect ratio. The structural weight comprises only about 18 percent of the design maximum gross weight. Although the geometric aspect ratio is 4.53, the winglet effect of the wing-tip-mounted vertical tails, increase the effective aspect ratio to approximately 7.9. Sufficient control power to handle the large rolling moment of inertia dictates a relatively high minimum approach velocity of 315 km/hr (170 knots). The airplane has acceptable spiral, Dutch roll, and roll-damping modes. A hardened stability augmentation system is required. The most significant noise source is that of the airframe. However, for both take-off and approach, the levels are below the FAR-36 limit of 108 db. The design mission fuel efficiency is approximately 50 percent greater than that of the most advanced, currently operational, large freighter aircraft. The direct operating cost is significantly lower than that of current freighters, the advantage increasing as fuel price increases.

Jernell, L. S.↗

NASA NTRS1994

Numerical simulation of large-scale field-aligned current generation from finite-amplitude magnetosonic waves

A two-dimensional numerical simulation of finite-amplitude magnetohydrodynamic (MHD) magnetosonic waves is performed under a finite-velocity background convection condition. Isothermal cases are considered for simplicity. External dissipation is introduced by assuming that the field-aligned currents are generated in proportion to the accumulated charges. The simulation results are as follows: Paired field-aligned currents are found from the simulated waves. The flow directions of these field-aligned currents depend on the angle between the background convection and the wave normal, and hence two pairs of field-aligned currents are found from a bowed wave if we look at the overall structure. The majority of these field-aligned currents are closed within each pair rather than between two wings. These features are not observed under slow background convection. The result could be applied to the cusp current system and the substorm current system.

Yamauchi, M.↗

DOE OSTI2022

Development of a Gibbs Energy Minimiser for the MOOSE-based Corrosion Modelling App Yellowjacket and Validation of MSTDB

Nuclear materials are highly complex multiscale, multiphysics systems,and an effective prediction of nuclear reactor performance and safety requires simulation capabilities that tightly couple different physical phenomena. The Idaho National Laboratory’s Multiphysics Object Oriented Simulation Environment (MOOSE) provides the computational foundation for performing such simulations. With the move towards advanced reactors, such as the Molten Salt Reactor (MSR), that employ high temperature fluids compared to conventional reactors, corrosion has become a problem of great interest. A new application called Yellowjacket is currently under development to directly couple thermodynamic equilibrium and kinetics with phase field models in order to model corrosion in MSRs. As part of Yellowjacket, a Gibbs energy minimiser is being developed to perform thermochemical equilibrium calculations for a range of different materials, which is currently in its infancy. This report describes the further progress towards the development of Yellowjacket Gibbs energy minimiser. Ontario Tech University is developing a new Gibbs energy minimiser for Yellowjacket which is the primary contribution of this work. The aim to develop a thermochemistry solver for the MOOSE framework following the same development philosophy and using the same tools and libraries. A special focus is on performance, documentation and SQA. Furthermore through a scope extension partway through the fiscal year a thorough assessment of the MSTDB-TC v1.3 was performed at Ontario Tech University in the context of continuous improvement and quality assurance. The objective of the work was to have an arm’s length review of the database to give confidence that the database is performing as it was intended while assessing its current state to give recommendations to future developments. This assessment involved two parts: A) a quantitative assessment, and B) a qualitative assessment. Part A involved developing an automated test-suite that would compute values from the database using Thermochimica with comparisons to experimental measurements for validation purposes, which gives confidence to the database’s stakeholders that its functioning properly. Part B involved reviewing all binary systems in the database and making a qualitative assessment with two performance indicators: comprehensiveness and overall confidence. It is important to note that the models in the database are empirical, which is to say that the quality of any model is highly dependent on the experimental data used to inform its development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1978

The feasibility of inflight measurement of lightning strike parameters

The appearance of nonmetallic structural materials and microelectronics in aircraft design has resulted in a need for better knowledge of hazardous environments such as lightning and the effects these environments have on the aircraft. This feasibility study was performed to determine the lightning parameters in the greatest need of clarification and the performance requirements of equipment necessary to sense and record these parameters on an instrumented flight research aircraft. It was found that electric field rate of change, lightning currents, and induced voltages in aircraft wiring are the parameters of greatest importance. Flat-plate electric field sensors and resistive current shunts are proposed for electric field and current sensors, to provide direct measurements of these parameters. Six bit analog-to-digital signal conversion at a 5 nanosecond sampling rate, short-term storage of 85000 bits and long term storage of 5 x 10 to the 7th power bits of electric field, current and induced voltage data on the airplane are proposed, with readout and further analysis to be accomplished on the ground. A NASA F-106B was found to be suitable for use as the research aircraft because it has a minimum number of possible lightning attachment points, space for the necessary instrumentation, and appears to meet operational requirements. Safety considerations are also presented.

Crouch, K. E.↗

DOE OSTI2025

Divertor characterization and access to dissipative divertor conditions in negative triangularity discharges in DIII-D

Reduced radial transport, short midplane-to-target parallel connection lengths, and a strong effect of cross-field drifts were responsible for the high densities required for detachment in strong negative triangularity (NT) configurations in DIII-D. Dissipative divertor conditions were achieved in NT discharges at different triangularity, injected power, plasma current, and toroidal field direction. Differences between negative and positive triangularity (PT) discharges are analyzed in this paper to understand the requirements for access to detached divertor conditions: power balance, geometry, radial transport and effect of cross-field particle drifts. Parametric dependencies of access to detachment on plasma current and power flowing into the scrape-off layer remained similar in negative and PT and impurity seeding was observed to reduce the density needed to detach by up to 30% at the expense of core impurity dilution. The impact of triangularity on core-edge integration was tested varying bottom triangularity at fixed top triangularity. The high density needed to detach was not intrinsic to the NT edge as shapes with positive lower triangularity and negative upper triangularity were able to detach at lower upstream densities while maintaining an ELM-free NT edge. Confinement degradation at deeper detachment levels was however observed in all NT shapes, often associated with radiation instabilities.

detachment↗

DOE OSTI2024

Carbon Mineralization in Fractured Mafic and Ultramafic Rocks: A Review

Mineral carbon storage in mafic and ultramafic rock masses has the potential to be an effective and permanent mechanism to reduce anthropogenic CO 2 . Several successful pilot-scale projects have been carried out in basaltic rock (e.g., CarbFix, Wallula), demonstrating the potential for rapid CO 2 sequestration. However, these tests have been limited to the injection of small quantities of CO 2 . Thus, the longevity and feasibility of long-term, large-scale mineralization operations to store the levels of CO 2 needed to address the present climate crisis is unknown. Moreover, CO 2 mineralization in ultramafic rocks, which tend to be more reactive but less permeable, has not yet been quantified. In these systems, fractures are expected to play a crucial role in the flow and reaction of CO 2 within the rock mass and will influence the CO 2 storage potential of the system. Therefore, consideration of fractures is imperative to the prediction of CO 2 mineralization at a specific storage site. In this review, we highlight key takeaways, successes, and shortcomings of CO 2 mineralization pilot tests that have been completed and are currently underway. Laboratory experiments, directed toward understanding the complex geochemical and geomechanical reactions that occur during CO 2 mineralization in fractures, are also discussed. Experimental studies and their applicability to field sites are limited in time and scale. Many modeling techniques can be applied to bridge these limitations. We highlight current modeling advances and their potential applications for predicting CO 2 mineralization in mafic and ultramafic rocks.

25 ENERGY STORAGE↗

NASA NTRS1993

Stormtime transport of ring current and radiation belt ions

A dynamical guiding-center simulation model is used to study the stormtime ion transport which leads to the formation of the ring current and diffusion in the radiation belts. Representative ions guiding-center motion in response to model storm-associated impulses in the convection electric field is traced for a range of ion mu values. The present numerical results are compared with previously formulated limiting idealization of particle transport in order to assess the limits of validity of these approximations. For ions having drift periods that exceed the duration of the main phase of the storm, their inward transport to form the stormtime ring current is appropriately described as direct convective access. For ions having drift periods comparable to the duration of the main phase of the storm, there is a transition between direct convective access and transport that resembles radial diffusion. Lower-energy ring-current ions at L of about 3 are freshly injected there from open adiabatic trajectories, whereas the higher-energy ring-current population consists of a mixture of freshly injected and previously trapped ions.

Chen, Margaret W.↗

DOE OSTI2025

Extending the dark matter reach of water Cherenkov detectors using Jupiter

We propose the first method for water Cherenkov detectors to constrain GeV-scale dark matter (DM) below the solar evaporation mass. While previous efforts have highlighted the Sun and Earth as DM capture targets, we demonstrate that Jupiter is a viable target. Jupiter’s unique characteristics, such as its lower core temperature and significant gravitational potential, allow it to capture and retain light DM more effectively than the Sun, particularly in the mass range below 4 GeV where direct detection sensitivity diminishes. Our calculations provide the first sensitivity estimates to GeV-scale annihilating DM within Jupiter, predicting Hyper-K can reach spin dependent cross sections as low as $𝜎^{SD}_{𝑝⁢𝜒}$ = 2×10 −35 cm 2 for DM masses below 2 GeV. This surpasses current solar limits and direct detection results. We additionally provide estimates for Super-K ORCA, and the IceCube-Upgrade, showing that these experiments could provide complimentary bounds to direct detection experiments.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1972

Effects of microcratering on the lunar surface.

Based on new laboratory impact data and current best estimates of the lunar micrometeoroid flux, calculations have been made of (1) the survival times of rocks on the lunar surface before they are catastrophically ruptured by meteoritic impacts; and (2) the rate of mass wasting by single particle abrasion. The calculated results are in systematic disagreement with observations in a direction suggesting that the current micrometeoroid flux may be greater than the long-term average integrated over the past several tens of millions of years. Most of the mass in the micrometeoroid flux is concentrated in particles with masses between .01 and 100 micrograms.

Gault, D. E.↗

DOE OSTI2022

Method of coating an electrical current collector and electrodes resulting therefrom

The present invention is directed to a method of coating an electrical current collector comprising treating a portion of a surface of the electrical current collector with an adhesion promoting composition to deposit a treatment layer over the portion of the surface of the electrical current collector, wherein the resulting surface of the electrical current collector comprises (a) a treated portion comprising the treatment layer and (b) a non-treated portion that lacks the treatment layer; electrodepositing an electrodeposited coating layer from an electrodepositable coating composition onto the surface of the electrical current collector to form a coated electrical current collector; and rinsing the coated electrical current collector, wherein the electrodeposited coating layer substantially adheres to the treated portion of the surface and does not adhere to the non-treated portion of the surface. Also disclosed are electrodes and electrical storage devices.

Oakes, Landon J.↗

DOE OSTI2022

Solar Photovoltaics: Supply Chain Deep Dive Assessment

This is one of a series of reports and deep dive assessments produced in response to Executive Order 14017 “America’s Supply Chains,” which directs the Secretary of Energy to submit a report on supply chains for the energy sector industrial base. The Executive Order is helping the federal government to build more secure and diverse U.S. supply chains, including energy supply chains. Over the past decade, solar power has gone from an emerging, niche technology to a mature energy industry. By 2035, solar power could supply 40% or more of U.S. electricity demand, dramatically accelerating the decarbonization of buildings, transportation, and industry; and, if current technology trends continue, it could do so without increasing the price of electricity. The rapid expansion of solar energy has the potential to yield broad benefits in the form of economic activity and workforce development. The solar industry already employs roughly 230,000 people in the United States, at an average wage that is higher than the national average for most comparable positions. By decarbonizing the electricity sector by 2035, the U.S. solar industry could employ 500,000–1,500,000 people by 2030. The components that are assembled to install a photovoltaic power system are produced by a global supply chain. Photovoltaic (PV) modules (also called panels) are made of cells that use a variety of technologies. There are two leading types of solar modules used in the United States, with crystalline silicon (c-Si) modules representing 84% of the market and cadmium telluride (CdTe) modules representing 16% of the market. Modules of either type require mounting structures to provide mechanical support (racking), which may be configured to follow the sun (tracking). The output of any PV module is direct current (dc), which is almost always converted to alternating current (ac) by an inverter.

14 SOLAR ENERGY↗

DOE OSTI2020

Reinterpretation of LHC Results for New Physics: Status and recommendations after Run 2

We report on the status of efforts to improve the reinterpretation of searches and measurements at the LHC in terms of models for new physics, in the context of the LHC Reinterpretation Forum. We detail current experimental offerings in direct searches for new particles, measurements, technical implementations and Open Data, and provide a set of recommendations for further improving the presentation of LHC results in order to better enable reinterpretation in the future. We also provide a brief description of existing software reinterpretation frameworks and recent global analyses of new physics that make use of the current data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2020

Reinterpretation of LHC Results for New Physics: Status and Recommendations after Run 2

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1998

Electrodynamic Tether Propulsion for Spacecraft and Upper Stages

Relatively short electrodynamic tethers can use solar power to 'push' against a planetary magnetic field to achieve propulsion without the expenditure of propellant. The groundwork has been laid for this type of propulsion. Important recent milestones include retrieval of a tether in space (TSS-1, 1992), successful deployment of a 20-km-long tether in space (SEDS-1, 1993), and operation of an electrodynamic tether with tether current driven in both directions (PMG, 1993). The planned Propulsive Small Expendable Deployer System (ProSEDS) experiment will use the flight-proven Small Expendable Deployer System (SEDS) to deploy a 5 km bare copper tether from a Delta II upper stage to achieve approximately 0.4 N drag thrust, thus deorbiting the stage. The experiment will use a predominantly 'bare' tether for current collection in lieu of the endmass collector and insulated tether approach used on previous missions. The flight experiment is a precursor to utilization of the technology on the International Space Station for reboost and the electrodynamic tether upper stage demonstration mission which will be capable of orbit raising, lowering and inclination changes, all using electrodynamic thrust. In addition, the use of this type of propulsion may be attractive for future missions at Jupiter.

Johnson, Les↗

NASA NTRS1987

High latitude currents in the 0600 to 0900 MLT sector - Observations from Viking and DMSP-F7

High-resolution magnetic field and charged-particle data acquired on March 25, 1986 by the Viking and DMSP-F7 satellites, as they traversed the dawn sector auroral zone on nearly antiparallel trajectories within 40 min of each oher, are analyzed. Magnetic field measurements by Viking at 0850 MLT and by DMSP at 0630 MLT indicate the presence of a large-scale earthward-directed region 1 Birkeland current and an upward-flowing region 2 current. Both satellites also observed a third Birkeland current adjacent to and poleward of the region 1 system with opposite flow. This poleward system is about 0.5 deg invariant latitude wide and has a current density comparable to the region 1 and 2 systems. The highest-latitude current is identified as region 0. Its charged-particle signatures were used to infer field line mapping to the equatorial plane.

Bythrow, P. F.↗

DOE OSTI2026

iDDS: intelligent distributed dispatch and scheduling for workflow orchestration

The intelligent distributed dispatch and scheduling (iDDS) service is a versatile workflow orchestration system designed for large-scale, distributed scientific computing. iDDS extends traditional workload and data management by integrating data-aware execution, conditional logic, and programmable workflows, enabling automation of complex and dynamic processing pipelines. Originally developed for the ATLAS experiment at the large hadron collider, iDDS has evolved into an experiment-agnostic platform that supports both template-driven workflows and a Function-as-a-Task model for Python-based orchestration. This paper presents the architecture and core components of iDDS, highlighting its scalability, modular message-driven design, and integration with systems such as PanDA and Rucio. We demonstrate its versatility through real-world use cases: fine-grained tape resource optimization for ATLAS, orchestration of large Directed Acyclic Graph (DAG) workflows for the Rubin Observatory, distributed hyperparameter optimization for machine learning applications, active learning for physics analyses, and AI-assisted detector design at the electron–ion collider. By unifying workload scheduling, data movement, and adaptive decision-making, iDDS reduces operational overhead and enables reproducible, high-throughput workflows across heterogeneous infrastructures. We conclude with current challenges and future directions, including interactive, cloud-native, and serverless workflow support.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

Theoretical Study of High Harmonic Generation in Monolayer NbSe 2

High harmonic generation (HHG) is a powerful probe of electron dynamics on attosecond to femtosecond time scales and has been successfully used to detect electronic and structural changes in solid-state quantum materials, including transition-metal dichalcogenides (TMDs). Among TMDs, bulk NbSe 2 exhibits charge density wave (CDW) order below 33 K and becomes superconducting below 7.3 K. Monolayer NbSe 2 also has superconducting and CDW behavior and is therefore interesting as a material whose different structural and electronic properties could be probed via HHG. Here, we predict the HHG response of the pristine 2H and CDW phases of monolayer NbSe 2 using real-time time-dependent density functional theory under the application of a simulated laser pulse excitation. We find that due to the lack of inversion symmetry in both monolayer phases, it is possible to excite even harmonics and that the even harmonics appear as the transverse components of the current response under excitations polarized along the zigzag direction of the monolayer, while odd harmonics arise from the longitudinal current response in all excitation directions. This suggests that the even and odd harmonic responses can be controlled via the polarization of the probing field, opening an avenue for potentially useful applications in optoelectronic devices.

36 MATERIALS SCIENCE↗

NASA NTRS1978

Future thrusts of the NASA space power program

General objectives and plan directions are given for current program support in the following areas: (1) solar cells and arrays; (2) batteries and fuel cells; (3) thermoelectric, thermionic, and Brayton cycle conversion systems; (4) circuits and subsystems for the management and distribution of power; and (5) the interactions of the environment with the power system and the spacecraft. Particular emphasis is given to the electrochemical energy conversion storage portion of the program where efforts are directed to improving the energy density and life of nickel cadmium batteries, to validating flight-weight silver hydrogen cells, to promoting the safe use of lithium primary batteries, to completing the silver zinc batteries and the orbital transfer fuel cell technology, to increasing the capacity of space batteries, to and to evaluating new electrochemical concepts for very high energy density. The use of the fuel cell electrolyzer concept for energy storage in both the dedicated and the truly regenerative mode is also being investigated.

Holcomb, L.↗