Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Development and applications of supersonic unsteady consistent aerodynamics for interfering parallel wings

The analytical development of unsteady supersonic aerodynamic influence coefficients for isolated and nearly parallel interfering coplanar and noncoplanar wings is described. Numerical formulations based on triangular discretizations of wings and diaphragms are handled in a kinematically consistent manner. Examples of isolated wing cases are compared with respect to aerodynamic influence coefficients and flutter boundaries. Aerodynamic influence coefficients for interfering wings are compared where corresponding results are available.

Appa, K.↗
NASA NTRS1972

Aerodynamic characteristics of a swept augmentor wing

A brief outline of augmentor wing research is presented and is followed by a discussion of large scale wind tunnel test results for a swept augmentor wing configuration. The results show that the augmentor wing can be applied to high speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.

Koenig, D. G.↗
NASA NTRS1973

Engine-over-the-wing noise research

Acoustic measurements for large model eingine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdb quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 db quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗
NASA NTRS1973

Laser Doppler velocimeter investigation of trailing vortices behind a semi-span swept wing in a landing configuration

Measured axial and tangential velocity profiles in the near wake vortices of a semi-span model of the Convair 990 wing in the NASA-Ames 7- by 10-foot wind tunnel are presented. A scanning laser Doppler velocimeter was used to obtain data at two different downstream stations (0.49 and 1.25 wing spans) at various angles of attack and configurations from wing alone to wing plus nacelles, anti-shock bodies, and flaps deflected 27 deg (landing configuration). It is shown that the velocity distributions within the wake are quite sensitive to span loading. Specifically, it is illustrated that an aircraft flying at given lift coefficient (C SUB L), can substantially reduce its trailing vortex upset potential by deploying its flaps and altering its flight attitude to maintain the same C SUB L. This might be taken into consideration along with performance and noise considerations in the selection of aircraft approach lift over drag.

Ciffone, D. L.↗
NASA NTRS1972

An experimental investigation of an oblique-wing and body combination at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot wind tunnel to determine the aerodynamic characteristics of an oblique high aspect ratio wing in combination with a high fineness-ratio Sears-Haack body. Longitudinal and lateral-directional stability data were obtained at wing yaw angles from 0 deg to 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 6 deg and 9 deg. The effects of changes in Reynolds number, dihedral, and trailing-edge angle were studied along with the effects of a roughness strip on the upper and lower surfaces of the wing. Flow-visualization studies were made to determine the nature of the flow on the wing surfaces.

Graham, L. A.↗
NASA NTRS1972

Aerodynamic characteristics of a swept augmentor wing

A brief outline of augmentor wing research sponsored by Ames Research Center is presented and is followed by a discussion of large-scale wind-tunnel test results for a swept augmentor wing configuration. The results showed that the augmentor wing could be applied to high-speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.

Koenig, D. G.↗
NASA NTRS1973

Wind tunnel tests of an F-8 airplane model equipped with an oblique wing

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to study the lift, drag and stability characteristics of a 0.087-scale model of an operational airplane fitted with an oblique wing. The model wing was of elliptical planform with an unswept aspect ratio of 12.7 and a thickness of 10 percent. All other external geometric features of the model were scaled to the basic full size operational airplane with the engine inlet faired closed. Longitudinal and lateral-directional stability data were obtained with the wing at sweep angles of 0 deg, 45 deg and 60 deg Test Mach numbers ranged from 0.6 to 1.4 deg Angles of attack were between minus 4 deg and 8 deg at zero sideslip. Angles of sideslip were between plus and minus 4 degrees for two angles of attack depending upon the wing configuration. Tests were conducted at a Reynolds number of 6 million per foot except for a few runs when balance capacity limited the Reynolds number to 4 million per foot.

Graham, L. A.↗
NASA NTRS1973

Analysis of high aspect ratio jet flap wings of arbitrary geometry.

Paper presents a design technique for rapidly computing lift, induced drag, and spanwise loading of unswept jet flap wings of arbitrary thickness, chord, twist, blowing, and jet angle, including discontinuities. Linear theory is used, extending Spence's method for elliptically loaded jet flap wings. Curves for uniformly blown rectangular wings are presented for direct performance estimation. Arbitrary planforms require a simple computer program. Method of reducing wing to equivalent stretched, twisted, unblown planform for hand calculation is also given. Results correlate with limited existing data, and show lifting line theory is reasonable down to aspect ratios of 5.

Lissaman, P. B. S.↗
NASA NTRS1973

Flutter of pairs of aerodynamically interfering delta wings.

To examine the effect on flutter of the aerodynamic interference between pairs of closely spaced delta wings, several structurally uncoupled 1/80th-scale models were studied by experiment and analysis. Flutter test boundaries obtained in NASA Langley's 26-in. transonic blowdown wind tunnel were compared with subsonic analytical results generated using the doublet lattice method. Trends for several combinations of vertical and longitudinal wing separation were determined, showing flutter speed significantly affected in the closely spaced configurations. A new flutter mechanism coupling one wing's first bending mode with the other wing's first torsion mode was predicted and observed.

Chipman, R. R.↗
NASA NTRS1973

Engine-over-the-wing noise research.

Acoustic measurements for large model engine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdB quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 dB quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗
NASA NTRS1973

Noise tests on an externally blown flap with the engine in front of the wing

Noise tests were conducted with a nozzle exhausting over a small scale model of an externally blown flap (EBF) lift-augmentation system, with exhaust impingement on the wing leading edge. Two series of tests were conducted: with wing leading edge inside the nozzle; and with leading edge set back from the nozzle exit plane 1 diameter on the jet axis. The results indicated no significant differences in spectral shape, level, or directivity pattern. Static lift and thrust tests were conducted on the same model indicated considerable flow attachment on both configurations, with slightly greater attachment and turning for the wing outside the nozzle. Finally, a comparison with engine-above- and engine-below-the-wing EBF's tested by previous investigators shows the acoustic performance of the configurations tested for this report to lie between the other two.

Karchmer, A. M.↗
NASA NTRS1973

Wind tunnel investigation of a large-scale 25 deg swept-wing jet transport model with an external blowing triple-slotted flap

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally blown triple-slotted flap. The lift of the model was augmented by the turbofan engine exhaust impingement on the flap surface. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The model was tested with two flap extents. One extended from 0.11 to 1.00 of the wing semispan, and the other extended from 0.11 to 0.75 of the wing semispan with a single-slotted aileron from 0.75 to 1.00 of the wing semispan. The results were obtained for several flap deflections with and without the horizontal tail at gross thrust coefficients from 0 to 4.0. Longitudinal and lateral data are presented with three and four engines operating.

Aoyagi, K.↗
NASA NTRS1974

An analytical study of the effects of jets located more than one jet diameter above a wing at subsonic speeds

A procedure has been developed to calculate the effects of blowing two jets over a swept tapered wing at low subsonic speeds. The algorithm used is based on a vortex lattice representation of the wing lifting surface and a line sink-source distribution to simulate the effects of the jet exhaust on the wing lift and drag. The method is limited to those cases where the jet exhaust does not intersect or wash the wing. The predictions of this relatively simple procedure are in remarkably good agreement with experimentally measured interference lift and interference induced drag.

Putnam, L. E.↗
NASA NTRS1974

Preliminary performance estimates of an oblique, all-wing, remotely piloted vehicle for air-to-air combat

A computerized aircraft synthesis program has been used to assess the effects of various vehicle and mission parameters on the performance of an oblique, all-wing, remotely piloted vehicle (RPV) for the highly maneuverable, air-to-air combat role. The study mission consists of an outbound cruise, an acceleration phase, a series of subsonic and supersonic turns, and a return cruise. The results are presented in terms of both the required vehicle weight to accomplish this mission and the combat effectiveness as measured by turning and acceleration capability. This report describes the synthesis program, the mission, the vehicle, and results from sensitivity studies. An optimization process has been used to establish the nominal RPV configuration of the oblique, all-wing concept for the specified mission. In comparison to a previously studied conventional wing-body canard design for the same mission, this oblique, all-wing nominal vehicle is lighter in weight and has higher performance.

Nelms, W. P., Jr.↗
NASA NTRS1974

An analytical study of the effects of jets located more than one jet diameter above a wing at subsonic speeds

A procedure has been developed for calculating the effects of blowing two jets over a swept tapered wing at low subsonic speeds. The algorithm used is based on a vortex-lattice representation of the wing lifting surface and a line sink-source distribution to simulate the effects of the jet exhaust on the wing lift and drag. The method is limited to those cases in which the jet exhaust does not intersect or wash the wing. The predictions of this relatively simple procedure are in remarkably good agreement with experimentally measured interference lift and interference induced drag.

Putnam, L. E.↗
NASA NTRS1974

Aerodynamic characteristics of three slender sharp-edge 74 degrees swept wings at subsonic, transonic, and supersonic Mach numbers

Slender sharp-edge wings having leading-edge sweep angles of 74 deg have been studied at Mach numbers from 0.60 to 2.80, at angles of attack from about minus 4 deg to 22 deg, and at angles of sideslip from 0 deg to 5 deg. The wings had delta, arrow, and diamond planforms. The experimental tests were made in the Langley 8-foot transonic pressure tunnel and the Langley Unitary Plan wind tunnel test section number 1. The theoretical predictions were made using the theories of NASA TN D-3767 and NASA TN D-6243. The results of the study indicated that the lift and drag characteristics as affected by planform and Mach number could be reasonably well predicted for the delta wing in the subsonic and transonic Mach number range. In the supersonic range, the delta and diamond wings were about equally good in the degree of agreement between experiment and theory. In making drag-due-to-lift predictions the vortex lift effects must be taken into account if reasonable results are to be obtained at moderate or high lift coefficients.

Davenport, E. E.↗
NASA NTRS1974

Analysis of three-dimensional unsteady flow around oscillating wings

A method based on the Navier-Stokes equations was developed for determining analytically the three-dimensional unsteady flow patterns around oscillating wings. The Helmholz vorticity transport equations were discretized in three-dimensional finite element form from a variational formulation and integrated numerically. At each time step of the numerical integration the velocity field was calculated from the representation of the three-dimensional wing by a system of optimized distribution of vortices in space. During the numerical integration of the vorticity transport equations the time-dependent boundary conditions on the wing were specified as external constraint conditions. Examples of obtained results describing the three-dimensional unsteady flow around a wing were presented.

Bratanow, T.↗
NASA NTRS1973

The role of wind tunnel testing in the development of advanced rotary-wing aircraft

The relations of wind tunnel test objectives to wind tunnel test requirements are reviewed in an assessment of the current role of wind tunnel testing in the development of advanced rotary-wing aircraft. Elements of typical development programs are examined, and a comparison of fixed wing and rotary wing aircraft programs is presented. Proposed new test facilities for fixed wing aircraft and typical aircraft program costs are discussed, along with the use of wind tunnels for tilt rotor research aircraft and the role of 40 x 80 ft wind tunnels in tilt rotor aircraft development. Some changes in current programs and methods are outlined for bringing about desired improvements.

Kelly, M. W.↗