SEARCH · Engineering Papers

Results for “WALLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Optimization studies for the development of adaptive wall wind tunnel

The development of adaptive wall wind tunnels makes it possible to establish interference-free boundaries in the region of the model. It is, therefore, feasible to simulate free air conditions. However, the amount of total testing time involved in establishing the required conditions and the complexity of the needed instrumentation prevent currently the use of such methods for routine production testing. Optimization studies have been proposed with the objective to find approaches which will make a more extended application of adaptive wall techniques possible. A new 25cm x 11cm adaptive wall test section was designed and installed to carry out some of these studies. Investigations envisaged are related to the development of a one step convergence method to reduce total testing time, and to measurement procedures which will permit a simplification of the instrumentation. Attention is given to the proposed concept, the test section, instrumentation, and the influence coefficients.

Bodapati, S.↗

NASA NTRS1986

Noise radiation directivity from a wind-tunnel inlet with inlet vanes and duct wall linings

The acoustic radiation patterns from a 1/15th scale model of the Ames 80- by 120-Ft Wind Tunnel test section and inlet have been measured with a noise source installed in the test section. Data were acquired without airflow in the duct. Sound-absorbent inlet vanes oriented parallel to each other, or splayed with a variable incidence relative to the duct long axis, were evaluated along with duct wall linings. Results show that splayed vans tend to spread the sound to greater angles than those measured with the open inlet. Parallel vanes narrowed the high-frequency radiation pattern. Duct wall linings had a strong effect on acoustic directivity by attenuating wall reflections. Vane insertion loss was measured. Directivity results are compared with existing data from square ducts. Two prediction methods for duct radiation directivity are described: one is an empirical method based on the test data, and the other is a analytical method based on ray acoustics.

Soderman, P. T.↗

NASA NTRS1987

Molded Concrete Center Mine Wall

Proposed semiautomatic system forms concrete-foam wall along middle of coal-mine passage. Wall helps support roof and divides passage into two conduits needed for ventilation of coal face. Mobile mold and concrete-foam generator form sections of wall in place.

Lewis, E. V.↗

NASA NTRS1986

Modeling the effects of wind tunnel wall absorption on the acoustic radiation characteristics of propellers

Finite element theory is used to calculate the acoustic field of a propeller in a soft walled circular wind tunnel and to compare the radiation patterns to the same propeller in free space. Parametric solutions are present for a 'Gutin' propeller for a variety of flow Mach numbers, admittance values at the wall, microphone position locations, and propeller to duct radius ratios. Wind tunnel boundary layer is not included in this analysis. For wall admittance nearly equal to the characteristic value of free space, the free field and ducted propeller models agree in pressure level and directionality. In addition, the need for experimentally mapping the acoustic field is discussed.

Baumeister, K. J.↗

NASA NTRS1986

Construction of a 2- by 2-foot transonic adaptive-wall test section at the NASA Ames Research Center

The development of a new production-size, two-dimensional, adaptive-wall test section with ventilated walls at the NASA Ames Research Center is described. The new facility incorporates rapid closed-loop operation, computer/sensor integration, and on-line interference assessment and wall corrections. Air flow through the test section is controlled by a series of plenum compartments and three-way slide vales. A fast-scan laser velocimeter was built to measure velocity boundary conditions for the interference assessment scheme. A 15.2-cm- (6.0-in.-) chord NACA 0012 airfoil model will be used in the first experiments during calibration of the facility.

Morgan, Daniel G.↗

NASA NTRS1987

Turbulent heat transfer in corrugated-wall channels with and without fins

A numerical study is performed examining flow and heat transfer characteristics in a channel with periodically corrugated walls. The complexity of the flow in this type of channel is demonstrated by such phenomena as flow impingement on the walls, separation at the bend corners, flow reattachment, and flow recirculation. Because of the strong nonisotropic nature of the turbulent flow in the channel, the full Reynolds-stress model was employed for the evaluation of turbulence quantities. Computations are made for several different corrugation periods and for different Reynolds numbers. The results computed by using the present model show excellent agreement with experimental data for mean velocities, the Reynolds stresses, and average Nusselt numbers. The study was further extended to a channel flow where fins are inserted at bends in the channel. It was observed that the insertion of fins in the flow passage has a visible effect on flow patterns and skin friction along the channel wall.

Amano, R. S.↗

NASA NTRS1988

Adaptive-Wall Wind Tunnel

Side vents controlled automatically to compensate for interference by walls. Improved test station for 2- by 2-Foot Adaptive-Wall Wind Tunnel at Ames Research Center equipped for automatic sensing and correction of effects of walls on airflow in vicinity of test model. New facility well suited for advanced research and development. Velocities measured along lines near model used to calculate velocities observed along lines farther from model if model were in free air. Calculated values compared with velocities measured along farther lines.

Morgan, Daniel G.↗

NASA NTRS1988

Compound Walls For Vacuum Chambers

Proposed compound-wall configuration enables construction of large high-vacuum chambers without having to use thick layers of expensive material to obtain necessary strength. Walls enclose chambers more than 1 m in diameter and several kilometers long. Compound wall made of strong outer layer of structural-steel culvert pipe welded to thin layer of high-quality, low-outgassing stainless steel.

Frazer, Robert E.↗

NASA NTRS1988

Theoretical and Experimental Studies of the Transonic Flow Field and Associated Boundary Conditions near a Longitudinally-Slotted Wind-Tunnel Wall

A theoretical examination of the slotted-wall flow field is conducted to determine the appropriate wall pressure drop (or boundary condition) equation. This analysis improves the understanding of the fluid physics of these types of flow fields and helps in evaluating the uncertainties and limitations existing in previous mathematical developments. It is shown that the resulting slotted-wall boundary condition contains contributions from the airfoil-induced streamline curvature and the non-linear, quadratic, slot crossflow in addition to an often neglected linear term which results from viscous shearing in the slot. Existing and newly acquired experimental data are examined in the light of this formulation and theoretical developments.

Everhart, Joel Lee↗

NASA NTRS1987

Conditionally-averaged structures in wall-bounded turbulent flows

The quadrant-splitting and the wall-shear detection techniques were used to obtain ensemble-averaged wall layer structures. The two techniques give similar results for Q4 events, but the wall-shear method leads to smearing of Q2 events. Events were found to maintain their identity for very long times. The ensemble-averaged structures scale with outer variables. Turbulence producing events were associated with one dominant vortical structure rather than a pair of counter-rotating structures. An asymmetry-preserving averaging scheme was devised that allowed a picture of the average structure which more closely resembles the instantaneous one, to be obtained.

Guezennec, Yann G.↗

NASA NTRS1988

Space Station pressure wall repair techniques

Space Station components are susceptible to hypervelocity impact damage from orbital debris and meteoroids. An especially vulnerable and critical space station component is the module pressure wall. Even with shielding, sufficiently large impacting particles can create penetrations ranging from pinholes to large jagged holes. This paper describes pressure wall damage repair patches along with procedures and tools for performing the repair. One patch incorporates an aluminum foil protected from the jagged hole edge with a Kevlar or foam pad. An adhesive holds the patch in place. Another patch uses a stiff plate held away from the damaged area by a low durrometer rubber ring which also seals the plate edge. An adhesive will also secure this patch in place. Procedures were developed to prepare the punctured wall surface and apply the patch under weightless and unpressurized conditions. The procedures were tested in a laboratory and in the MSFC Neutral Buoyancy Simulator with models of the patches and tools.

Gibbins, Martin N.↗

NASA NTRS1988

A panel method procedure for interference assessment in slotted-wall wind tunnels

This paper describes a method for three-dimensional wind tunnel interference assessment developed specifically for slotted-wall tunnels. The method is an adaptation to the assessment problem of a previously published high-order panel method procedure for simulating the flow in slotted-wall tunnel test sections. The method uses a mixed outer boundary condition, primarily a Neumann condition, with measured pressure constraints used to control only those boundary phenomena which can not be specified accurately a priori. Assessment results are illustrated from a calibration test with variations in wall geometry, and from tests of a generic subsonic transport aircraft configuration.

Kemp, William B., Jr.↗

NASA NTRS1988

Structure of rough-wall turbulent boundary layers

Recent experiments have shown that, in rough-wall turbulent boundary layers, drag varies systematically with the spanwise aspect ratio lambda(z) (span/height) of roughness elements. In this paper, the effect of lambda(z) on turbulence structure has been examined. Based on lambda(z), the roughness in a transversely grooved surface with lambda(z) much greater than 1 is the opposite extreme of model plant canopies with lambda(z) much less than 1, studied in wind tunnels, whereas sandgrain is an intermediate type. Second-, third-, and fourth-order turbulence moments have been measured in turbulent boundary layers over transversely grooved and smooth surfaces and compared with available turbulence structure measurements over other types of surfaces. The near-wall turbulence structure is found to vary with lambda(z). The instantaneous motions involved in the flux of shear stress near the wall in smooth and transversely grooved surfaces are opposite in sign to those in three-dimensional roughness. The former is explained in terms of hairpin vortices alone, while the latter group is modeled to have an additional vortex (the so-called necklace vortex which straddles a three-dimensional roughness element near its base).

Bandyopadhyay, Promode R.↗

NASA NTRS1988

Theoretical model for VITA-educed coherent structures in the wall region of a turbulent boundary layer

Experiments on wall-bounded shear flows (channel flows and boundary layers) have indicated that the turbulence in the region close to the wall exhibits a characteristic intermittently formed pattern of coherent structures. For a quantitative study of coherent structures it is necessary to make use of conditional sampling. One particularly successful sampling technique is the Variable Integration Time Averaging technique (VITA) first explored by Blackwelder and Kaplan (1976). In this, an event is assumed to occur when the short time variance exceeds a certain threshold multiple of the mean square signal. The analysis presented removes some assumptions in the earlier models in that the effects of pressure and viscosity are taken into account in an approximation based on the assumption that the near-wall structures are highly elongated in the streamwise direction. The appropriateness of this is suggested by the observations but is also self consistent with the results of the model which show that the streamwise dimension of the structure grows with time, so that the approximation should improve with the age of the structure.

Landahl, Marten T.↗

NASA NTRS1989

Acoustic propagation in curved ducts with extended reacting wall treatment

A finite-element Galerkin formulation was employed to study the attenuation of acoustic waves propagating in two-dimensional S-curved ducts with absorbing walls without a mean flow. The reflection and transmission at the entrance and the exit of a curved duct were determined by coupling the finite-element solutions in the curved duct to the eigenfunctions of an infinite, uniform, hard wall duct. In the frequency range where the duct height and acoustic wave length are nearly equal, the effects of duct length, curvature (duct offset) and absorber thickness were examined. For a given offset in the curved duct, the length of the S-duct was found to significantly affect both the absorptive and reflective characteristics of the duct. A means of reducing the number of elements in the absorber region was also presented. In addition, for a curved duct, power attenuation contours were examined to determine conditions for maximum acoustic power absorption. Again, wall curvature was found to significantly effect the optimization process.

Baumeister, Kenneth J.↗

NASA NTRS1989

OTVE combustor wall condition monitoring

Conventional ultrasonics, eddy current, and electromagnetic acoustic transduction (EMAT) technologies were evaluated to determine their capability of measuring wall thickness/wear of individual cooling channels in test specimens simulating conditions in the throat region of an OTVE combustion chamber liner. Quantitative results are presented for the eddy current technology, which was shown to measure up to the optimum 20-mil wall thickness with near single channel resolution. Additional results demonstrate the capability of the conventional ultrasonics and EMAT technologies to detect a thinning or cracked wall. Recommendations for additional eddy current and EMAT development tests are presented.

Szemenyei, Brian↗

NASA NTRS1988

Transmission loss of double wall panels containing Helmholtz resonators

Data and an analysis are presented on the use of Helholtz resonators in double wall panels (i.e., aircraft sidewalls). Several wall materials and resonator configurations were tested, and the resonators were found to substantially increase the transmission loss of the double wall system at the tuning frequency.

Prydz, R. A.↗

NASA NTRS1989

Is the great attractor really a great wall?

Some of the cosmological consequences of a late-time phase transition which produces light domain walls are discussed. The observed peculiar velocity field of the universe and the observed isotropy of the microwave backgroud radiation severely constrain the wall surface density in such as scenario: G(omega) less than about 0.0001 H0 (H0 is the present value of the Hubble parameter). The most interesting consequence of such a phase transition is the possibility that the local, coherent streaming motion of about 600 km/s reported by Dressler et al (1987) could be explained by the repulsive effect of a relic domain wall within the Hubble volume provided that G(omega)/H0 = 0.0001.

Stebbins, Albert↗