Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VOLT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Wear Trends of the HERMeS Thruster as a Function of Throttle Point

A series of short-duration (200 hour) wear tests were conducted with two Hall Effect Rocket with Magnetic Shielding (HERMeS) technology demonstration units (TDU). Front pole covers, cathode keeper, and discharge channel wear were characterized as a function of discharge voltage, magnetic field strength, and chamber pressure. No discharge channel erosion was observed. Inner pole cover erosion was shown to be a weak function of discharge voltage with most erosion occurring at the lowest value, 300 volts. The TDU-3 keeper electrode eroded with each operating condition, with high magnetic field yielding the greatest erosion rate. The TDU-1 keeper electrode exhibited net deposition suggesting its configuration is more consistent with meeting overall HERMeS service life requirements. Ratios of molybdenum to graphite erosion rates suggests, with high uncertainty, that the sputtering ions are originating downstream of the thruster exit plane, striking the surface with small angles of incidence.

life (durability)↗

Generation of High Pressure Oxygen via Electrochemical Pumping in a Multi-Stage Electrolysis Stack

An oxygen pump can produce high-purity high-pressure oxygen. Oxygen ions (O(2-)) are electrochemically pumped through a multi-stage electrolysis stack of cells. Each cell includes an oxygen-ion conducting solid-state electrolyte between cathode and anode sides. Oxygen dissociates into the ions at the cathode side. The ions migrate across the electrolyte and recombine at the anode side. An insulator is between adjacent cells to electrically isolate each individual cell. Each cell receives a similar volt potential. Recombined oxygen from a previous stage can diffuse through the insulator to reach the cathode side of the next stage. Each successive stage similarly incrementally pressurizes the oxygen to produce a final elevated pressure.

Setlock, John A↗

Production of Negative Hydrogen Ions Within the MMS Fast Plasma Investigation Due to Solar Wind Bombardment

The particle data delivered by the Fast Plasma Investigation instrument aboard National Aeronautics and Space Administration's Magnetospheric Multiscale (MMS) mission allow for exceptionally high-resolution examination of the electron and ion phase space in the near-Earth plasma environment. It is necessary to identify populations which originate from instrumental effects. Using Fast Plasma Investigation's Dual Electron Spectrometers, we isolate a high-energy (approximately kiloelectron volt) beam, present while the spacecraft are in the solar wind, which exhibits an azimuthal drift with period associated with the spacecraft spin. We show that this population is consistent with negative hydrogen ions H− generated by a double charge exchange interaction between the incident solar wind H+ ions and the metallic surfaces within the instrument. This interaction is likely to occur at the deflector plates close to the instrument aperture. The H− density is shown to be approximately 0.2-0.4% of the solar wind ion density, and the energy of the negative ion population is shown to be 70% of the incident solar wind energy. These negative ions may introduce errors in electron velocity moments on the order of 0.2-0.4% of the solar wind velocity and significantly higher errors in the electron temperature.

Magnetospheric Multiscale↗

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗

Predicting Global Ground Geoelectric Field With Coupled Geospace and Three-Dimensional Geomagnetic Induction Models

We forecast the global effects of space weather on the geoelectric and geomagnetic fields using a novel combination of methods. We use a realistic three-dimensional (3-D) model of Earth's electrical conductivity and a realistic representation of magnetospheric and ionospheric current systems. Our scheme involves the following steps: (1) We run a global magnetohydrodynamic model of the magnetosphere coupled to an electrostatic model of the ionosphere. (2) We calculate a global time series of the ground magnetic field resulting from the ionospheric, field-aligned, and magnetospheric currents of the global magnetohydrodynamic model. (3) We approximate this external field by an equivalent source current flowing in a thin shell above Earth. (4) We calculate a global time series of geoelectric and geomagnetic fields from the equivalent current and a 3-D conductivity model of Earth that also takes into account the coast effect due to large horizontal conductivity gradient. We verify our implementation by comparing the results against known analytic and numeric solutions, and then apply our scheme to the geomagnetic storm of 14 and 15 December 2006. In particular, we show that accounting for 3-D structure of Earth's conductivity results in significantly enhanced geoelectric field at large lateral gradients of conductivity, especially in coastal regions, both at middle and high latitudes. In the studied geomagnetic storm the largest values of 3-D geoelectric field are detected at high latitudes reaching 2.5 volts per kilometer and the 3-D effect extends inland by a few hundred kilometers.

Honkonen, I.↗

Direct Observation of Electron Distributions Inside Millisecond Duration Electron Holes

Despite the importance of millisecond duration spatial structures [chorus wave nonlinearity or time domain structures (TDS)] to plasma dynamics, there have been no direct observations of the generation and interaction of these waves and TDS with electrons at the millisecond timescale required for their understanding. Through superposition of 0.195 ms Magnetospheric Multiscale Satellite electron measurements inside 37 superposed, millisecond duration electron holes, the first observations of electron spectra and pitch angle distributions on a submillisecond timescale have been obtained. They show that keV electrons inside the superposed electron hole are accelerated by several hundred volts and that the spectrum of electrons inside the electron hole contain several maxima and minima that are explained by a model of electron energy changes on entering the holes. We report the first observation of trapped electrons inside the TDS, in accordance with the theoretical requirement that such electrons must be present in order to form the phase space holes. Mechanisms of electron acceleration by electron holes (through perpendicular energy gain as the TDS moves into a converging magnetic field) and scattering (due to the perpendicular electric field) are discussed.

Mozer, F. S.↗

Characterizing Microfluidic Operations Underlying an Electrowetting Heat Pipe on the International Space Station

Electrowetting heat pipes (EHPs) are a newly conceptualized class of heat pipes, wherein the adiabatic wick section is replaced by electrowetting-based pumping of the condensate (as droplets) to the evaporator. Specific advantages include the ability to transport high heat loads over long distances, low thermal resistance and power consumption, and the absence of moving mechanical parts. In this work, we describe characterization of key microfluidic operations (droplet motion and splitting) underlying the EHP on the International Space Station (ISS). The testing was performed under the Advanced Passive Thermal eXperiment (APTx) project, a project to test a suite of passive thermal control devices funded by the ISS Technology Demonstration Office at NASA JSC (Johnson Space Center). A rapid manufacturing method was used to fabricate the electrowetting device on a printed circuit board. Key device-related considerations were to ensure reliability and package the experimental hardware within a confined space. Onboard the ISS, experiments were conducted to study electrowetting-based droplet motion and droplet splitting, by imaging droplet manipulation operations via pre-programmed electrical actuation sequences. An applied electric field of 36 Volts per micron resulted in droplet speeds approaching 10 millimeters per second. Droplet splitting dynamics were observed and the time required to split droplets was quantified. Droplet motion data was analyzed to estimate the contact line friction coefficient. Overall, this demonstration is the first-ever electrowetting experiment in space. The obtained results are useful for future design of the EHP and other electrowetting-based systems for microgravity applications.

Electrowetting↗

Plasma Science in Planetary Entry

Spacecraft entering a planetary atmosphere dissipate a great deal of energy into the surrounding gas. In the frame of reference of the vehicle, the atmospheric gas suddenly decelerates from hypersonic (Mach ~5-50) to subsonic velocities. The kinetic energy of the gas is rapidly converted to thermal and chemical energy, forming a bow shock behind which a plasma with energies on the order of one electron volt (eV) is produced. The resulting shock layer relaxes from strong thermal non-equilibrium that is translationally hot but internally cold and un-ionized toward a thermochemically equilibrated plasma over a distance of a few centimeters. Composition is dependent upon the planetary atmosphere – Air for Earth, CO2/N2 for Mars and Venus, N2/CH4 for Titan and H2/He/CH4 for Saturn, Neptune and Jupiter. Typical velocities of entry may range from 3-7 km/s (4-25 MJ/kg) for Titan/Mars, 8-14 km/s (30-100 MJ/kg) for Earth/Venus, and 25-40 km/s (300-800 MJ/kg) for outer planets. The equilibrium plasmas produced from these conditions are highly dissociated (up to and above 99%) and ionized (0.1- 15%), with temperatures from 7,000-15,000K and pressures from 0.1-1.0 bar. Understanding the behavior of these plasmas – the way in which they approach equilibrium, how they radiate, and how they interact with materials – is an active area of research necessitated by requirements to predict and test the performance of thermal protection systems (TPS) that enable spacecraft to deliver scientific instruments, and people, to foreign worlds and back to Earth. The endeavor is a multi-physics problem, with key processes highlighted in Fig. 1. This white paper describes the current state of the art in simulating shock layer plasmas both computationally and in ground test facilities. Gaps requiring further research and development are identified.

Cruden, Brett A.↗

Lunar Plant Experiment: Testing Plant Germination in Lunar Gravity and Ionizing Radiation

We present an open design for a first plant growth module on the Moon (LPX). The primary science goal of lunar habitat is to investigate germination and initial plant growth when subject to the combined effects of lunar gravity and lunar surface radiation. The LPX module has been designed to be a flexible base unit that can be adapted to fly to the lunar surface on a variety of landers and rovers. LPX has size and shape of a 1 Unit CubeSat (10 centimeters on a side) and a total mass of 0.3 kilograms. The base will contain a seed module holding around 50 Arabidopsis seeds and provide approximately 0.5 liters of normal air at standard pressure. By the action of a small pump, water will be released after landing to initiate germination. Images will document the germination, initial growth, phototropism, and circumnutation of the small plants while sunlight remains available. A CO2 sensor tracks the release of CO2 during germination and the subsequent uptake of CO2 by photosynthesis. Simulations indicate that the CO2 peak level will be an increase by 2250 parts per million after 2 earth-days and then decline to about 1000 parts per million after 7 earth-days. The camera and CO2 sensor interfaces are USB. The water pump initiation requires a 5-volt signal. After initiation of germination by the addition of water, the habitat must be maintained above 22 degrees Centigrade to allow for plant growth and below 27 degrees Centigrade to prevent damage to the plants. This relatively tight temperature tolerance will require thermal control systems using reflecting surfaces and insulation that must be specifically designed for each lander or rover. The plant growth unit will function to tilt angles of 20 degrees along any axis. Total image data volume required to gauge the plant growth rate and leaf area is 1 megabyte (minimum data required) to 40 megabytes (preferred data). The lid of the habitat will allow adequate sunlight for plant growth. To provide for optimum growth, light levels in the plant growth stage need to be between 75 and 150 micromoles per meter squared per second interval.

first plant growth↗

Flight Readiness of Mochii S: Portable Spectroscopic Scanning Electron Microscope Facility on the International Space Station (ISS)

The ISS (International Space Station) currently lacks the capability to image and chemically analyze nano-to-micron scale particles from numerous engineering systems. To identify these particles, we must wait for a re-entry vehicle to return them from low earth orbit for ground-based SEM (Scanning Electron Microscope) / EDS (Energy Dispersive X-Ray Spectroscopy) analysis. This may take months, potentially delaying the affected system. Having an EDS-equipped SEM (Mochii S) aboard the ISS will accelerate response time thereby enhancing crew and vehicle safety by rapid and accurate identification of microscopic threats, especially in time-critical situations.The Mochii S payload will be stationed in the Japanese Experiment Module (JEM) powered by 120 VAC (Volts Alternating Current) inverter and connected to station Ethernet and WiFi (Fig. 1). To date the Mochii S payload has undergone testing for command and data handling, power quality, flight vibration, and radiation testing at Johnson Space Center (JSC). Mochii's high-RPM (Revolutions Per Minute) rotating vacuum pumps and high voltage systems have been reviewed to meet safety standards by JSC (Johnson Space Center) Engineering. Topology of the system in the JEM module has been baselined by ISS Safety and JAXA (Japan Space Exploration Agency). Digital controls to and from ISS over Joint Station LAN (Local Area Network) uplink have been simulated and the latencies and data rates have been found to be sufficient for successful operation of the payload from ground.Transporting sensitive electron optical instruments aboard a rocket that sustains 7G acceleration for 8 minutes and then operating it the unique microgravity (micro-g) environment is no trivial matter. To meet strict safety requirements and increase robustness for mission success, over 500 unique verifications must be completed before the payload is certified for spaceflight. Two of which will be discussed in detail are: vibroacoustic testing and magnetic susceptibility shielding and validation.

Mochii↗

Formation of the Potential Jump over the Geomagnetically Quiet Sunlit Polar Cap Region

We consider the formation of a potential drop over the Earth's polar cap during geomagnetically quiet daytime. The observed potential drop is primarily defined by the hydrogen, photoelectron, and polar rain fluxes ratios and depends strongly on the energy distribution of the photoelectron flux. Polar rain is an essential component of the model required for plasma quasineutrality. The potential distribution along the magnetic field line has two regions, with a small, gradual, potential drop of 3 to 4 volts and a potential jump. The value of the potential jump depends on the hydrogen ion to photoelectron flux ratio and is also controlled by polar rain electrons. With quasineutrality required at its upper boundary, the jump only occurs in the presence of polar rain and its location depends on the polar rain flux. Model predictions compare well with FAST (Fast Auroral SnapshoT) observations presented by Kitamura et al.(2012, https://doi.org/10.1029/2011JA017459).

Khazanov, G. V.↗

Firbimatic Vacuum Degreaser Cleaning Study

The purpose of this cleaning study was to establish the baseline of contaminants that can be removed using the Firbimatic Multisolvent 50-volt vacuum degreaser using Kyzen’s Metalnox® M6386 Solvent on 2219 aluminum alloy panels. Four different cleaning methods were used with six known contaminants. For each contaminant, five panels were contaminated—one was kept as a control, and the remaining four were cleaned using the vacuum degreaser. All applicable NASA, company, laboratory, and test-specific standard test practices were followed. Pre- and post-test results and photographs can be found in the appendices.

Morris, B. D.↗

The Formation of Electron Heat Flux in the Region of Diffuse Aurora

Whistler and electrostatic electron cyclotron harmonics waves are responsible for scattering and precipitating the energetic plasma sheet electrons that drive the diffuse aurora. These primary electrons with energies in the kiloelectron volt range, simultaneously precipitating in magnetically conjugate regions, produce the secondary electron population and can be reflected by the atmosphere back through the magnetosphere and precipitate into the conjugate region with additional follow‐up atmospheric backscatter. Primary, degraded, and secondary electrons can be trapped back into the magnetosphere as they travel back and forth between the two magnetically conjugate ionospheres and continuously delivering their energy to the cold plasma sheet electrons and form the electron thermal fluxes that deposit this energy at the upper ionospheric altitudes. We consider the formation of these heat fluxes focusing on the magnetosphere‐ionosphere energy interplay of the entire superthermal electron spectra from 1 eV up to 10 keV and discuss the efficiency of the different spectral energy intervals that contribute to the electron plasma heating at the magnetospheric altitudes. Our parametric studies at L = 6.8, with lower and upper band chorus whistler wave amplitudes of 10 pT and electron cyclotron harmonic wave amplitudes of 1 mVm−1, indicate the dominant role of the whistler mode in the formation of the electron heat flux coming from the magnetosphere to the ionosphere.

George V. Khazanov↗

Gateway Power Quality Lessons Learned

Power Quality is a physical description of the electrical characteristics that allow the system to function properly without significant loss of performance or life. This physical description includes steady state voltage limits, transient voltage limits in normal/abnormal conditions, ripple voltage, stability, fault conditions, and more. All which are vital for improving reliability, ensuring stable operation, defining proper fault recovery, and ensuring a ‘plug and play’ approach to design and integration. Typically, a specification for Power Quality is created based on expected system performance or an existing standard, such as the International Space Power System Interoperability Standards (ISPSIS). One example of such a specification is the Gateway Power Quality Specification. It defines the requirements and characteristics of the 120 Volt direct current electrical power system for the Gateway Electrical Power System (EPS) and the Gateway Electrical Power Consuming Equipment (EPCE). This specification also maintains a separate requirement verification section that defines test methods for requirement verification. The test methods include analysis, test, inspection, and demonstration. These test methodologies and requirements are used to ensure that the loads operate when connected to the specified power quality and performance as defined by this specification. The challenge with developing a specification is that desired system characteristics are not always fully matured before the specification is needed and many performance requirements may be application specific. This drives the need to utilize lessons learned through extensive analysis and testing as well as historical knowledge to finalize requirements. Some example requirements where this is important are Small and Large Signal Stability, Ripple Voltage, Inrush/Surge Currents, and Fault Containment. Lessons learned are also important in the testing, analysis, and verification to ensure consistent and accurate results to verify performance. This presentation will cover the lessons learned for power quality relative to ripple, inrush/surge, fault containment, testing/verification, and more.

Power Quality↗

40kW Fission Surface Power System (FSPS) Deployability

Continuous power at the kilowatt level will be imperative for future lunar users including crew infrastructure, future science, and in-situ resource utilization (ISRU). The Compass Team explored both 10 kilowatt electric (kWe) and 40 kWe concepts, assuming planned lander and rover capabilities. Both concepts found that a crew pressurized rover chassis, repurposed for deploying reactor power components, could place a fission surface power system (FSPS) at least one kilometer from users. While the 10 kWe fission power system (FPS) could be deployed as a single unit, the 40 kWe system was too large and had to be deployed in multiple trips with the same rover. Key technologies and design approaches included a high-assay low-enriched uranium (HALEU), yttrium hydride (YH) moderated heat pipe reactor, Stirling convertors, deployable radiators based on International Space Station (ISS) designs, and power conversion/transmission at ±2800 volts of direct current (VDC).

Lunar reactor 40kW fission deployable↗

Artemis IV Docking in Radiation Belt Charging Environment

NASA’s Artemis IV mission is planned to deliver the International Habitation Module (I-Hab) to the Gateway space station in lunar orbit. The I-Hab will be launched aboard the Space Launch System (SLS) vehicle as a co-manifested payload with the Orion spacecraft. After translunar injection begins, the Orion spacecraft will separate from the SLS Exploration Upper Stage (EUS) and then dock with the I-Hab to extract it from the EUS. Because of the altitude, orientation, and time for this to occur, the vehicle-to-vehicle potential between the I-Hab/EUS vehicle and Orion spacecraft could exceed several thousand volts. The docking of these two spacecrafts with such large differential potentials presents a challenge for the vehicles. This presentation describes the space environments at the docking altitude, the calculated vehicle-to-vehicle potential, and the possible impacts of the resulting voltage and current transients occurring at first contact. Additionally, possible risk mitigation tests to demonstrate compatibility with the transient current and voltages will be presented.

Matthew Mccollum↗

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗