Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Temperature modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Preliminary Measurements on the BOLT Geometry in the Supersonic Low Disturbance Tunnel

Experiments were performed in the Mach 3.5 Supersonic Low Disturbance Tunnel on the BOundary-Layer Transition (BOLT) geometry. The goal of this campaign was to assess changes to the transition front by varying the freestream noise and the model surface quality. The model was printed of polycarbonate and is 30% scale of the flight geometry. It was tested under noisy and quiet conditions at different streamwise positions in the tunnel and was also tested before and after improvements were made to the model surface through sanding and gap reduction. Pitch and yaw angles were nominally zero. The model surface temperature was measured using infrared thermography and thermocouples as the unit Reynolds number was swept from 4.75 – 15.8 × 10 6 m −1 . Boundary-layer transition was observed near the midspan of the model for unit Reynolds numbers above 10×10 6 m −1 in quiet flow, while transition was already observed on the shoulders below 5×10 6 m −1 in noisy flow. The model surface enhancements improved the symmetry of the transition front for quiet flow but made only slight differences for noisy flow. In quiet flow, the impact of streamwise positioning on transition was more significant on the model shoulders compared to the central region. The difference in the shoulder heating was likely due to variation in noise radiated from the nozzle sidewalls. The total temperature and initial wall temperatures were near 300 K and 293 K, respectively, which generally resulted in negative convective heat-flux values into the model. Hot-wire anemometry was also utilized to characterize the freestream and to conduct a planar survey near the base of the model for the 7.92 × 10 6 m −1 quiet condition. The survey captured the thickening of the boundary layer at the centerline and the vortical nature of the flow outboard of it. Spectral analysis of the mass-flux fluctuations near the midspan demonstrates that the boundary layer is laminar and suggests that the thick boundary layer caused the relatively warm centerline observed in the infrared images.

boundary layer transition↗

Testing a dynamical model for mid-latitude sea surface temperature anomalies

The present investigation is concerned with the development and testing of a dynamical model for sea surface temperature (SST) anomalies in the midlatitudes. The model is an extension of the stochastic forcing model, suggested by Frankignoul and Hasselmann (1977), in which SST anomalies arise naturally as a response of the slowly varying upper ocean to the rapidly varying air-sea fluxes. The conducted analysis confirms strongly the validity of this model. The results suggest that advection by mean ocean currents plays an important role in some regions. Attention is given to the governing equations, a statistical model, SST anomaly advection, heat flux anomalies, wind-driven mass transport in the mixed layer, mixed-layer depth, aspects of model testing, and the atmospheric forcing.

Frankignoul, C.↗

Preliminary Measurements on the BOLT Geometry in the Supersonic Low Disturbance Tunnel

Experiments were performed in the Mach 3.5 Supersonic Low Disturbance Tunnel on the BOundary-Layer Transition (BOLT) geometry. The goal of this campaign was to assess changes to the transition front by varying the freestream noise and the model surface quality. The model was printed of polycarbonate and is 30% scale of the flight geometry. It was tested under noisy and quiet conditions at different streamwise positions in the tunnel and was also tested before and after improvements were made to the model surface through sanding and gap reduction. Pitch and yaw angles were nominally zero. The model surface temperature was measured using infrared thermography and thermocouples as the unit Reynolds number was swept from 4.75 -- 15.8 x 10^6 m^{-1}. Boundary-layer transition was observed near the midspan of the model for unit Reynolds numbers above 10 x 10^6 m^{-1} in quiet flow, while transition was already observed on the shoulders below 5 x 10^6 m^{-1} in noisy flow. The model surface enhancements improved the symmetry of the transition front for quiet flow but made only slight differences for noisy flow. In quiet flow, the impact of streamwise positioning on transition was more significant on the model shoulders compared to the central region. The difference in the shoulder heating was likely due to variation in noise radiated from the nozzle sidewalls. The total temperature and initial wall temperatures were near 300 K and 293 K, respectively, which generally resulted in negative convective heat-flux values into the model. Hot-wire anemometry was also utilized to characterize the freestream and to conduct a planar survey near the base of the model for the 7.92 x 10^6 m^{-1} quiet condition. The survey captured the thickening of the boundary layer at the centerline and the vortical nature of the flow outboard of it. Spectral analysis of the mass-flux fluctuations near the midspan demonstrates that the boundary layer is laminar and suggests that the thick boundary layer caused the relatively warm centerline observed in the infrared images.

boundary layer transition↗

Human and Natural Influences on the Changing Thermal Structure of the Atmosphere

Since the late 1970s, satellite-based instruments have monitored global changes in atmospheric temperature. These measurements reveal multidecadal tropospheric warming and stratospheric cooling, punctuated by short-term volcanic signals of reverse sign. Similar long- and short-term temperature signals occur in model simulations driven by human-caused changes in atmospheric composition and natural variations in volcanic aerosols. Most previous comparisons of modeled and observed atmospheric temperature changes have used results from individual models and individual observational records. In contrast, we rely on a large multimodel archive and multiple observational datasets. We show that a human-caused latitude/altitude pattern of atmospheric temperature change can be identified with high statistical confidence in satellite data. Results are robust to current uncertainties in models and observations. Virtually all previous research in this area has attempted to discriminate an anthropogenic signal from internal variability. Here, we present evidence that a human-caused signal can also be identified relative to the larger "total" natural variability arising from sources internal to the climate system, solar irradiance changes, and volcanic forcing. Consistent signal identification occurs because both internal and total natural variability (as simulated by state-of-the-art models) cannot produce sustained global-scale tropospheric warming and stratospheric cooling. Our results provide clear evidence for a discernible human influence on the thermal structure of the atmosphere.

Santer, Benjamin D.↗

Economic Dispatch Model of Nuclear High-Temperature Reactor with Hydrogen Cogeneration in Electricity Market

Hydrogen produced without carbon emissions could be a useful fuel as nations look to decarbonize their electricity, transport, and industry sectors. Using the iodine–sulfur (IS) cycle coupled with a nuclear heat source is one method for producing hydrogen without the use of fossil fuels. An economic dispatch model was developed for a nuclear-driven IS system to determine hydrogen sale prices that would make such a system profitable. The system studied is the HTTR-GT/H2, a design for power and hydrogen cogeneration at the Japan Atomic Energy Agency’s High Temperature Engineering Test Reactor. This study focuses on the development of the economic model and the role that input data plays in the final calculated values. Using a historical price duration curve shows that the levelized cost of hydrogen (LCOH) or breakeven sale price of hydrogen would need to be 98.1 JPY/m3 or greater. Synthetic time histories were also used and found the LCOH to be 67.5 JPY/m3. The price duration input was found to have a significant effect on the LCOH. As such, great care should be used in these economic dispatch analyses to select reasonable input assumptions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Investigating Kinetic Mechanisms of Soot Formation in Plasma Pyrolysis of Methane via Active Learning (Final Technical Report)

Plasma pyrolysis of methane is an effective route for zero-carbon hydrogen production. Yet, soot generated from pyrolysis of hydrocarbons is detrimental to the climate and human health. There is ample experimental and theoretical evidence that suggests polycyclic aromatic hydrocarbons (PAHs) are the molecular precursors to soot particles. The reaction pathways of PAH formation are intricately dependent on a multitude of process parameters, whose kinetic mechanisms are not well-understood in plasma pyrolysis. This project aims to leverage advances in the kinetic modeling of soot formation in combustion, as well as in surrogate modeling and active learning, to systematically investigate the effects of process parameter on the kinetics of PAH formation in plasma pyrolysis of methane. To this end, we propose to use the PAH formation kinetics model developed by the PPPL/PU group based on the well-established ABF and HACA mechanisms, coupled with low-temperature plasma models. We will develop an active learning (AL) framework based on Bayesian optimization to systematically and data-efficiently explore the complex and multivariable parameter space of plasma pyrolysis in order to quantify the effects of plasma and feed parameters on the ABF and HACA kinetic pathways. AL is the branch of machine learning concerned with systematically querying samples from a system (experimental or computational) to train a data-driven model that maps design parameters to a performance criterion. We will use the data generated via AL to perform global sensitivity analysis, combined with uncertainty quantification, to elucidate the impact of different reaction pathways on minimizing formation of soot precursors. This study will result in an improved understanding of kinetics of PAH formation in plasma pyrolysis and can pave the way for more advanced mechanistic studies (e.g., soot nucleation mechanisms). Additionally, the findings will be useful for establishing practical strategies for increasing the pyrolysis efficiency and producing high-grade carbon for synthesis of nanomaterials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

IMPACT OF REDUCING THE 100 C LIQUIDUS TEMPERATURE OFFSET ON WASTE LOADING TARGETS

The objective of this report is to assess the potential impact of reducing conservatism in the implementation of the current liquidus temperature (TL) model in the Product Composition Control System (PCCS) on the ability to target higher waste loadings (WLs) for future sludge batches. No changes to the TL model or the associated uncertainties (model or measurement) are proposed, rather only changes in the magnitude of the offset used between the nominal melt pool temperature (1150 C) and the Property Acceptance Region (PAR) value (1050 C). This strategy is consistent with that outlined and initially assessed by Brown et al. (2001). In that report, the authors stated even a fairly conservative change in this safety factor could have a significant impact on waste loading. The results of this study clearly indicate that the implementation of an 1100 C TL PAR criterion (which translates into a reduction in the TL offset from 100 C to 50 C) can have significantly positive impacts on the ability to gain access to WLs exceeding 45%. This is especially true for those frit and sludge systems that are TL limited using the current 1050 C TL criterion, and are not limited by a second constraint (such as viscosity, nepheline, or durability) until much higher WLs. Examples of various glass forming systems are provided that are currently limited to maximum WLs in the mid-40s, but could be processed in the lower 50s through implementation of this new strategy. One example is in the Sludge Batch 10 (SB10) system, where for a specific glass forming system the projected operating window of 38-41% WL (using the current constraints) became 38-52% WL with the use of an 1100 C TL PAR value. This change both provided access to significantly higher WLs, and transitioned a once infeasible flowsheet to a system that could potentially be processed in the Defense Waste Processing Facility (DWPF). This potential change in the TL constraint also provides access to frit compositions (or glass forming regions) that are not accessible under the current limitations. These new composition regions not only provide access to higher WLs, but may also allow frit development efforts to target other specific properties to support enhanced melter operations. It should be noted that under certain flowsheet conditions, the implementation of the 1100 C TL PAR must be accompanied by a shifting categorization of what is deemed an acceptable operating window for DWPF operation. For example, the use of a 50 C offset may not be effective if access to WLs < 30% are still required. Assuming the intent of implementing the 1100 C PAR criterion is to gain access to higher WLs (> 45%), the need to identify frit and sludge systems that are predicted to form acceptable glasses at these lower WLs (< 30%) should no longer be of concern. Although this strategy could have a significant impact on DWPF's ability to target higher WLs (> 45%), its implementation is not risk free. The reduction in the TL offset does reduce the conservatism currently implemented, which is aimed at minimizing or eliminating the potential for massive devitrification within the melt pool. Prior to implementation of this alternative strategy, DWPF should perform a risk-based assessment or review of this alternative approach to ensure it aligns with needs and processing strategies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Model atmospheres for cool stars

This report contains an extensive series of model atmospheres for cool stars having a wide range in chemical composition. Model atmospheres (temperature, pressure, density, etc.) are tabulated, along with emergent energy flux distributions, limb darkening, and information on convection for selected models. The models are calculated under the usual assumptions of hydrostatic equilibrium, constancy of total energy flux (including transport both by radiation and convection) and local thermodynamic equilibrium. Some molecular and atomic line opacity is accounted for as a straight mean. While cool star atmospheres are regimes of complicated physical conditions, and these atmospheres are necessarily approximate, they should be useful for a number of kinds of spectral and atmospheric analysis.

Johnson, H. R.↗

A Micromechanics Finite Element Model for Studying the Mechanical Behavior of Spray-On Foam Insulation (SOFI)

A micromechanics model has been constructed to study the mechanical behavior of spray-on foam insulation (SOFI) for the external tank. The model was constructed using finite elements representing the fundamental repeating unit of the SOFI microstructure. The details of the micromechanics model were based on cell observations and measured average cell dimensions discerned from photomicrographs. The unit cell model is an elongated Kelvin model (fourteen-sided polyhedron with 8 hexagonal and six quadrilateral faces), which will pack to a 100% density. The cell faces and cell edges are modeled using three-dimensional 20-node brick elements. Only one-eighth of the cell is modeled due to symmetry. By exercising the model and correlating the results with the macro-mechanical foam behavior obtained through material characterization testing, the intrinsic stiffness and Poisson s Ratio of the polymeric cell walls and edges are determined as a function of temperature. The model is then exercised to study the unique and complex temperature-dependent mechanical behavior as well as the fracture initiation and propagation at the microscopic unit cell level.

Ghosn, Louis J.↗

Hot-Carrier Degradation in GaN HEMTs Due to Substitutional Iron and Its Complexes

We report the experimental data, quantum-mechanical calculations, and engineering-level modeling that provide insight into the atomic-scale processes that underlie the hot-electron degradation of AlGaN/GaN high-electron-mobility transistors during electrical stress at moderate drain bias. There is relatively large degradation (up to 20%) of the peak transconductance (g m ) in the semi-ON state, along with a small shift of the threshold voltage (V T ). The V T shift and g m degradation increase with temperature. A model of the degradation is presented, based on the hot-carrier-induced defect generation. The model considers carrier energy distributions for different temperatures obtained using an ensemble Monte Carlo (EMC) approach. The Ensemble Monte-Carlo results show that the concentration of energetic carriers is maximum at the end of the gate on the gate-drain access side in the semi-ON state of operation. The degradation is directly related to the number of carriers with sufficient energy to generate defects, and the carrier energy distribution depends strongly on the device temperature. The first-principles density functional theory calculations and the analysis suggest that the dehydrogenation of substitutional iron and its complexes is the dominant cause of the observed degradation in these devices.

Engineering↗

Comparison of theoretical and measured brightness temperature of a soybean canopy

A model for the brightness temperature of a canopy which is based on the physical characteristics of the vegetation is being developed. This model uses the Peake model to relate the scattering coefficient of the vegetation to its radiometric brightness temperature and a discrete scattering model to computer the scattering coefficient. A distorted Born approximation is used to provide a tractable solution to the scattering problem. To verify the theory a comparison has been made with experiments. Radiometric measurements of brightness temperature were made at L- and C-bands over a crop of mature soybeans, along with ground truth measurements. All model input parameters were measured; there were no free parameters to adjust to obtain agreement with the measurements. Results showed that agreement between theory and measurements was reasonable for horizontal polarization at both L- and C-bands with dry underlying soil.

Lang, R. H.↗

Thermal modeling of the NASA-Ames Research Center Cryogenic Optical Test Facility and a single-arch, fused-natural-quartz mirror

A thermal model of the dewar and optical system of the Cryogenic Optical Test Facility at NASA-Ames Research Center was developed using the computer codes SINDA and MONTE CARLO. The model was based on the geometry, boundary conditions, and physical properties of the test facility and was developed to investigate heat transfer mechanisms and temperatures in the facility and in test mirrors during cryogenic optical tests. A single-arch, fused-natural-quartz mirror was the first mirror whose thermal loads and temperature distributions were modeled. From the temperature distribution, the thermal gradients in the mirror were obtained. The model predicted that a small gradient should exist for the single arch mirror. This was later verified by the measurement of mirror temperatures. The temperatures, predicted by the model at various locations within the dewar, were in relatively good agreement with the measured temperatures. The model is applicable to both steady-state and transient cooldown operations.

Ng, Y. S.↗

N=1 Wess-Zumino model in d=3 at zero and finite temperature

Supersymmetric renormalization group flow equations for the effective superpotential of the three-dimensional Wess-Zumino model are derived at zero and non-zero temperature. This model with fermions and bosons interacting via a Yukawa term possesses a supersymmetric analogue of the Wilson-Fisher fixed-point. At zero temperature we determine the phase-transition line in coupling-constant space separating the supersymmetric from the nonsupersymmetric phase. At finite temperature we encounter dimensional reduction from 3 to 2 dimensions in the infrared regime. We determine the finite-temperature phase diagram for the restoration of the global Z{sub 2}-symmetry and show that for temperatures above the Z{sub 2} phase transition the pressure obeys the Stefan-Boltzmann law of a gas of massless bosons in 2+1 dimensions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Model Implementation of Boron Removal Using CaCl{sub 2}-CaO-SiO{sub 2} Slag System for Solar-Grade Silicon

A new CaCl{sub 2}-CaO-SiO{sub 2} slag system was recently proposed to remove boron from metallurgy-grade silicon by oxidized chlorination and evaporation. To further investigate the boron transformation process at a high temperature, a model implementation to present the transfer of boron from molten silicon to the gas phase via slag is introduced. Heat transfer, fluid flow, the chemical reactions at the interface and surface, the mass transfer and diffusion of boron in the molten silicon and slag, and the evaporation of BOCl and CaCl{sub 2} were coupled in this model. After the confirmation of the thermal field, other critical parameters, including the boron partition ratios (L{sub B}) for this slag from 1723 K to 1823 K (1450 °C to 1550 °C), the thicknesses of the velocity boundary layer at the surface and interface, the mass transfer coefficients of the boundary layer at the surface and interface, and partial pressure of BOCl in the gas phase were analyzed to determine the rate-limiting step. To verify this model implementation, boron removal experiments were carried out at various temperatures and with various initial mass ratios of slag to silicon (μ). The evaporation rate of CaCl{sub 2} was also measured by thermogravimetry analysis (TGA).

36 MATERIALS SCIENCE↗

Theoretical studies of a molecular beam generator

We consider the problem of modeling a high temperature diatomic gas N2 flowing through a converging-diverging high expansion nozzle. The problem is modeled in two ways. The first model uses a single temperature with variable specific heats as functions of this temperature. For the second model we assume that the various degrees of freedom all have a Boltzmann population distribution which means that each degree of freedom has its own temperature and consequently each system state can be characterized by these temperatures. This suggests the formulation of a second model with a vibrational degree of freedom as having its own temperature along with a rotational-translational degree of freedom with its own temperature. Initially the vibrational degree of freedom is excited by heating the gas to a high temperature. As the high temperature gas expands through the nozzle throat there is a sudden drop in the rotational-translational temperature along with a finite relaxation time for the vibrational degree of freedom to achieve equilibrium with the rotational-translational degree of freedom. That is, the temperature change that occurs when the N2 gas passes through the nozzle throat is so great that the changes in the vibrational degree of freedom lags behind the rotational-translational energy changes. The resulting relaxation time is finite. It is in this context that the term nonequilibrium is used. That is, the term nonequilibrium denotes the fact that the energy content of the various degrees of freedom are characterized by two temperatures. We neglect any chemical reactions resulting from the high temperatures which could also add nonequilibrium effects. We develop the basic equations for the two models in various forms in order to check the derivations with other sources. The final form which is solved numerically consists of the scaled equations in a conservative dimensionless form.

Heinbockel, John H.↗

A comprehensive experimental and kinetic modeling study of di-isobutylene isomers: Part 1

We report di-isobutylene has received significant attention as a promising fuel blendstock, as it can be synthesized via biological routes and is a short-listed molecule from the Co-Optima initiative. Di-isobutylene is also popularly used as an alkene representative in multi-component surrogate models for engine studies of gasoline fuels. However, there is limited experimental data available in the literature for neat di-isobutylene under engine-like conditions. Hence, most existing di-isobutylene models have not been extensively validated, particularly at lower temperatures (< 1000 K). Most gasoline surrogate models include the di-isobutylene sub-mechanism published by Metcalfe et al. with little or no modification. The current study is undertaken to develop a detailed kinetic model for di-isobutylene and validate the model using a wide range of relevant experimental data. Part 1 of this study exclusively focuses on the low- to intermediate temperature kinetics of di-isobutylene. An upcoming part 2 discusses the high-temperature model development and validation of the relevant experimental targets. Ignition delay time measurements for the di-isobutylene isomers were performed at pressures ranging from 15 - 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 diluted in air and in the temperature range 650 - 900 K using two independent rapid compression machine facilities. In addition, measurements of species identified during the oxidation of these isomers were performed in a jet-stirred reactor and in a rapid compression machine. A detailed kinetic model for the di-isobutylene isomers is developed to capture the wide range of new experimental targets. For the first time, a comprehensive low-temperature chemistry submodel is included. The differences in the important reaction pathways for the accurate prediction of the oxidation of the two DIB isomers are compared using reaction path analysis. In conclusion, the most sensitive reactions controlling the ignition delay times of the DIB isomers under the pressure and temperature conditions necessary for autoignition in engines are identified.

09 BIOMASS FUELS↗