Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Segregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Analysis of Brazing Effect on Hot Corrosion Behavior of a Nickel-Based Aerospace Superalloy

The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium-depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration are necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.

36 MATERIALS SCIENCE↗

Influence of Melt Superheating Treatment on Solidification Characteristics and Rupture Life of a Third-Generation Ni-Based Single-Crystal Superalloy

The influence of melt superheating treatment on the melt properties, solidification characteristics, and rupture life of a third-generation Ni-based single-crystal superalloy was investigated to reveal the critical temperature range of melt structure evolution and its effect on rupture life. The results showed that the viscosity of superalloy decreased but the surface tension increased with increasing superheating temperature. Two characteristic temperature points where the melt viscosity and undercooling degree suddenly change were determined to be 1600 °C and 1700 °C, respectively. Similarly, the stability of the solidification interface firstly improved and then weakened with increasing superheating temperature. The dendrite arms were well refined and the segregation was reduced at 1700 °C. In addition, the rupture life obtained at 1100 °C and 137 MPa increased by approximately 30 pct, approaching the rupture life of the corresponding superalloy containing 2 pct Ru, with increasing superheating temperature from 1500 °C to 1700 °C. When the melt was further heated to 1800 °C, the rupture life decreased. The evolutions of solidification characteristics and rupture life with increasing melt superheating temperature were attributed to changes in the melt structure.

36 MATERIALS SCIENCE↗

Solidification of Calcium Ferrite Melt Using Ultrasonic Vibration: Effect and Mechanism

Calcium ferrite (CF) is a very important binder phase in iron ore sintering processes. To improve the microstructure of CF, power ultrasound was introduced during its solidification process, and the effect of immersion depth of ultrasonic probe (IDUP) on the properties of CF was investigated in detail. The results indicated that the microstructure of CF was greatly refined; the grain size decreased from 2864 μm without ultrasonic vibration to 841 μm with ultrasonic vibration at an immersion depth of 30 mm. Without ultrasonic vibration, the density and compressive strength of CF slag were 3904 kg/m{sup 3} and 38.3 MPa, respectively. When the IDUP was increased from 10 to 30 mm, the density and compressive strength of CF increased from 4049 to 4452 kg/m{sup 3} and 52.5 to 87.3 MPa, respectively. Further, the reducibility of CF was examined. The reduction time, at the same reduction rate, decreased from 347 minutes without ultrasonic vibration to 200 minutes with ultrasonic vibration at an IDUP of 30 mm. The rate-limiting step was obviously improved, which may be attributable to the grain refinement of CF and composition segregation in the slag. In general, the properties of CF were greatly improved due to the cavitation and acoustic streaming of ultrasonic waves.

36 MATERIALS SCIENCE↗

Solidification Behavior of Calcium Ferrite Under Ultrasonic Vibration

Ultrasonic vibration was applied to the solidification process of calcium ferrite (CF) to modify the grain size and improve the homogeneity of the solidified microstructure. The effects of ultrasound on microstructure, density, compressive strength, and reducibility were studied. The acoustic pressure decreased and then increased along the axis symmetry due to the attenuation of acoustic pressure and reflection of ultrasonic waves in the melt under a fixed power. When the ultrasonic power was increased, the general acoustic pressure increased, which was beneficial to the avoidance of macropores and to improvement of the microstructure. Coarse acicular CF grains were significantly refined; the grain size decreased from 1967 to 442 μm when the ultrasonic power was increased from 0 to 300 W. The density of the samples increased from 4370 to 4680 kg/m{sup 3} due to cavitation and acoustic streaming effects. Ultrasonic vibration greatly improved the ultimate compressive strength of CF; the values were 41.8 ± 2.1 to 67.3 ± 3.4 MPa for ultrasonic powers of 100 to 300 W, respectively. Without ultrasonic treatment, it was only 37.4 ± 1.9 MPa. Ultrasonic vibration also influenced the reduction time of CF due to the composition segregation in the slag during solidification.

36 MATERIALS SCIENCE↗

Microsegregation Measurement: Methods and Applications

Microsegregation is chemical variation at the microstructural level in a solidified ingot, which can cause undesirable effects on material properties. Its formation is driven by different levels of solute elemental solubility between solid and liquid phases, resulting in solute buildup or depletion in the liquid phase during solidification. Characterization of microsegregation can be essential for understanding its formation and removing it through heat treatment. Measurement is frequently carried out via scanning electron microscope (SEM), though metallographic analysis, mechanical testing and optical radiography have been used. SEM analysis can consist of point measurements on single dendrites, line scans across or along dendrites, elemental maps, and extended line-based or grid-based analyses extending over many dendrites, which can generate large amounts of data. Line-based or grid-based data can be analyzed using scatterplots of element concentrations to visualize segregation behavior and sorting/ranking of data by a single element or a combination of elements, to give compositional profiles as a function of extent of solidification. For both qualitative and quantitative analyses, effects of phase transformations and secondary phases need to be considered as well as sorting of measurement errors when generating compositional profiles. Applications of analysis include determination of partition ratios, examination of solute–element interactions, determination of effects of cooling rate and back diffusion, applications to freckling studies, validations of modeling, and development of heat-treatment profiles.

36 MATERIALS SCIENCE↗

Unexpected Charpy Impact Toughness Spike of 1.25Cr-0.5Mo Steel After Simulated Postweld Heat Treatment

The present study elaborates on the effect of simulated postweld heat treatment (SPWHT) on microstructure and mechanical property variations of 1.25Cr-0.5Mo steel. With the increase in SPWHT holding time, lath ferrite tends to morph into blocky ferrite, and carbides aggregate along grain boundaries. Although tensile strength keeps decreasing, Charpy impact toughness undergoes a spike, followed by a sharp decrease. Such an interesting phenomenon is explained by the competition between high-angle grain boundary population and carbide segregation, and bodes well to the pressure vessel industry for optimized PWHT.

36 MATERIALS SCIENCE↗

Assessing the Influence of NaCl on the Reduction of a Siliceous Laterite Nickel Ore Under Caron Process Conditions

The reduction by hydrogen and the thermal decomposition of a siliceous nickel laterite ore in the presence of NaCl were studied using thermogravimetric analysis (TGA). Reduction tests on H{sub 2} atmosphere in rotary kiln were performed in the presence of NaCl and the product of the reaction was leached in ammoniacal solution. The presence of only 1 pct of NaCl in the furnace increased the nickel extraction values from ≈ 3 to ≈ 90 pct when the experiment was carried out at 850 °C. According to the results of X-ray diffractometry and TGA, the presence of NaCl in the system and the reducing atmosphere of H{sub 2} promote the segregation of nickel according to the following steps: (1) Nickel oxide reduction by hydrogen: NiO + H{sub 2(g)} → Ni + H{sub 2}O{sub (g)}. (2) Formation of HCl: Al{sub 2}SiO{sub 5} + 2NaCl + SiO{sub 2} + H{sub 2}O → 2HCl(g) + 2NaAlSiO{sub 4}. (3) Chlorination of metallic nickel by HCl: Ni + 2HCl{sub (g)} → NiCl{sub 2} + H{sub 2(g)}. (4) Reduction of nickel chloride by hydrogen: NiCl{sub 2} + H{sub 2(g)} → Ni + 2HCl{sub (g)}.

36 MATERIALS SCIENCE↗

Porosity Prediction in A356 Wheel Casting

A FLUENT™-based thermal-fluid-compositional model has been developed and applied to a low-pressure, die-cast, A356 aluminum alloy wheel to explore the effects of macro-segregation of hydrogen and late-stage liquid encapsulation on pore formation during solidification. Based on the evolution of temperature, pressure, and hydrogen concentration in the liquid output from FLUENT, the porosity size distribution has been predicted at a number of locations in a commercially produced wheel using an in-house micro-porosity model. The porosity model incorporates pore nucleation kinetics based on hydrogen supersaturation, and two modes of pore growth: the first, occurring at low solid fractions is based on hydrogen diffusion; and the second, occurring at high solid fractions is based on conservation of volume. Samples from a commercially cast wheel have been analyzed using X-ray micro-tomography to provide basic validation of the micro-porosity model. The predicted results showed that the evolution in pressure has the dominant effect on pore growth, but only under conditions where pores have nucleated prior to late-stage liquid encapsulation. Otherwise, the cooling rate appears to have the dominant effect. The accuracy of the model is discussed in terms of the predicted pore size distribution and number density of pores. Areas for continued development are presented.

36 MATERIALS SCIENCE↗

Structure and Reactivity of Low-Rank Coal Chars Prepared from Fluidized Bed and Moving Bed Pyrolyzers and the Potential for Using Them in Pulverized Coal Injection (PCI)

Utilizing pyrolysis chars as the injection fuel in a blast furnace can reduce the dependence on high-quality pulverized coal injection (PCI) coal. In this study, the physical properties and reaction characteristics of chars prepared from two different industrial-scale pyrolyzers (fluidized bed and moving bed) are investigated. The results reveal remarkable component segregation in the char particles with different particle sizes. The properties of large-size char particles are found to better satisfy the PCI fuel requirement in a blast furnace. Compared with PCI coal, the char particles exhibit a rough surface, well-developed pore structure, and less-ordered chemical structure of carbon. Results from isothermal combustion, isothermal gasification, and drop tube furnace experiments show that both types of chars exhibit a better reactivity than PCI coal. The excellent reactivity of chars is closely related to its high Brunauer–Emmett–Teller surface area and relatively poor chemical ordering during conversion. Based on these characteristics, both fluidized bed char (FBC) and moving bed char (MBC) have a great potential to be used as PCI fuels. The application method of chars for PCI in a blast furnace is proposed finally.

01 COAL, LIGNITE, AND PEAT↗

Effect of Diffusion Length in Modeling of Equiaxed Dendritic Solidification under Buoyancy Flow in a Configuration of Hebditch–Hunt Experiment

Modeling of equiaxed solidification is vital for understanding the solidification process of metallic alloys. In this work, an extended literature review is given for the models currently used for equiaxed solidification simulations. Based on this analysis, we present a three-phase multiscale equiaxed solidification model in which some approximations regarding solute transport at microscopic scale are put together in a new way and incorporated into macroscopic transport equations. For the latter, a term relating to the momentum exchange between the two phases is revised, and a modification for the grain packing algorithm is proposed. A modernized model for equiaxed dendrite growth is tested using a case of solidification of Sn-5 wt pct Pb alloy in a parallelepiped cavity that mimics the Hebditch–Hunt experiment. The results obtained using two approaches to calculate diffusion length are presented and compared both with each other and with numerical results from elsewhere. It is demonstrated that diffusion length has a crucial effect on the final segregation pattern.

36 MATERIALS SCIENCE↗

Investigations of Cadmium Manganese Telluride Crystals for Room-temperature Radiation Detection

Cadmium manganese telluride (CMT) has high potential as a material for room-temperature nuclear-radiation detectors. We investigated indium-doped CMT crystals taken from the stable growth region of the ingot and compared its characteristics with that from the last-to-freeze region. We employed different techniques, including synchrotron white-beam x-ray topography (SWBXT), current-voltage (I-V) measurement, and low-temperature photoluminescence spectra, and we also assessed their responses as detectors of radiation exposure. The crystal from the stable growth region proved to be superior to that from the last-to-freeze region; it is a single-grain crystal, free of twins, and displayed a resistivity higher by one order of magnitude. The segregation of indium dopant in the ingot might be responsible for its better resistivity. Furthermore, we recorded a good response in the detector fabricated from the crystal taken from the stable growth region; its ({mu}{tau})e value was 2.6 x 10{sup -3} cm{sup 2}/V, which is acceptable for thin detectors, including their application in medicine.

36 MATERIALS SCIENCE↗

Precipitation Kinetics of M{sub 23}C{sub 6} Carbides in the Super304H Austenitic Heat-Resistant Steel

The precipitation kinetics of M{sub 23}C{sub 6} carbides in Super304H and TP304H steels were investigated using the selective-etching method, SEM backscattered electron images and Image-Pro-Plus 6.0 software. Precipitation–temperature–time (PTT) diagrams of M{sub 23}C{sub 6} carbides in the as-received Super304H (fine grains), coarsened Super304H (coarse grains) and TP304H (coarse grains) steels all show the typical C-shaped character with nose temperature range from 800 to 850 °C. Compared with the TP304H steel, the same trend is found of the PTT curve of M{sub 23}C{sub 6} carbides for both kinds of Super304H steels, but their start lines move to the right and finish lines to the left. The preferential formation of Nb(C,N) phase at grain boundaries in the Super304H steels inhibited the nucleation of M{sub 23}C{sub 6} carbides in the early stage of precipitation, causing the right shift of the start line of PTT curve. The main reason for the left shift of the finish line of the two Super304H steels was the quicker growing and coarsening rate of M{sub 23}C{sub 6} in the later precipitation stage due to their higher C content than in TP304H. For the difference in PPT curves between the two grain sizes of the Super304H steel, the lower diffusion rate of atoms in the coarse-grained Super304H steel may explain its righter finish line than the fine-grained counterpart, while the reason for its lefter start line is due to the higher solute segregation along coarse-grained boundaries.

36 MATERIALS SCIENCE↗

Effect of Mo-rich Fillers in Pulsed Current Gas Tungsten Arc Welding of Inconel 718 for Improved Strength and Hot Corrosion Resistance

The formation of Laves phase in the fusion zone of Inconel 718 welds is considered to be detrimental and requires major attention, as this phase deteriorates the mechanical properties and high-temperature corrosion resistance. This present study addresses the use of current pulsing technique on the gas tungsten arc welding of 5-mm-thick Inconel 718 plates. Nb-free fillers, namely ERNiCrMo-10 and ERNiCrMo-14, are chosen for joining these plates. Microstructure studies revealed the segregation of Mo-rich phases at the inter-dendritic regions of the fusion zone of both the weldments. Further, the occurrence of detrimental Laves phase was minimized while employing Mo-rich fillers. It is inferred from the tensile studies that the fractures occurred in the parent metal for ERNiCrMo-10 filler and at the fusion zone while employing ERNiCrMo-14. Room-temperature Charpy impact studies also affirm that the impact toughness of ERNiCrMo-10 welds is significantly greater than that of ERNiCrMo-14. Hot corrosion studies were performed on the coupons by exposing them to a synthetic molten salt environment comprising Na{sub 2}SO{sub 4} + 60%V{sub 2}O{sub 5} at 800 °C for 50 h. Owing to the presence of higher amounts of Cr{sub 2}O{sub 3} and NiO, both fusion zones exhibited better hot corrosion resistance than the parent metal. The novel outcome of the study reiterates that with the use of current pulsing and Mo-rich fillers, the detrimental phase shall be controlled.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Three-Layer TIG-Welded 2219 Aluminum Alloys with Dissimilar Heat Treatments

2219-C10S and 2219-CYS aluminum alloys are 2219 aluminum alloys with different heat treatment processes, and they have been widely used in the aerospace industry. In the present study, 2219-C10S and 2219-CYS aluminum alloys were butt-welded by three-layer tungsten inert gas arc welding (with the welding center of the third layer shifted toward the CYS side), and the microstructure characteristics and mechanical properties of the welded joint were investigated. The lamellar θ′ phases, the bulk or rod θ phases, and the coarse rod-shaped or pancake-shaped Al-Cu-Fe-Mn phases coexisted in the two aluminum alloys. The Cu content of the α-Al matrix and the distribution of eutectic structures of different welding layers in the weld zone (WZ) were varied, implying that the segregation degrees of the Cu element were different due to the different welding thermal cycles in different welding layers. The microhardness values of the CYS side were much higher than those of the C10S side in each region on both sides of the joint. The tensile test deformation was concentrated mainly in the regions of WZ and the over aged zone (OAZ), where the microhardness values were relatively low. The main deformation concentrated region was transferred from the CYS side to the C10S side with the increase in the tensile load during the tensile test. The fracture behavior of the tensile test showed that the macroscopic crack initiated near the front weld toe had gone through the crack blunt region, the shear fracture region of the partially melted zone (PMZ), and the shear fracture region of OAZ. Meanwhile, the fracture characteristics gradually evolved from brittle to ductile. The concentrated stress and the dense eutectic structure in the region near the front weld toe of the C10S side contributed to the fracture of the joint. The shift of the welding center of the third layer to the CYS side resulted in two effects: (i) the microhardness values from the middle layer to the top layer in the PMZ of the CYS side were the most significantly increased and (ii) the distance between the front weld toe and the fusion line of the CYS side was significantly larger.

36 MATERIALS SCIENCE↗

Microstructural Characterization, Mechanical Properties, and Corrosion Resistance of Dental Co-Cr-Mo-W Alloys Manufactured by Selective Laser Melting

In this paper, the microstructure, mechanical properties, and corrosion resistance of the dental Co-Cr-Mo-W alloys fabricated by selective laser melting (SLM) were systematically investigated and correlated. The microstructure of the SLM group (SG) specimens is composed of extremely fine columnar crystals, exhibiting supersaturated and homogeneous character. The matrix mainly consists of face-centered-cubic (FCC) cobalt solid solutions, and minimal hexagonal-close-packed (HCP) cobalt solid solutions. Mechanical test results showed that the 0.2% yield strength of SG was 775 ± 7 MPa, and the ultimate tensile strength was 1118 ± 25 MPa. The elongation of SG was 8.28 ± 0.4%, and the microhardness of SG was 476 ± 10 HV. All of these values largely exceeded the cast group (CG) specimens. The high strength is attributed to their fine columnar crystals and supersaturated matrices. The fewer content from the HCP phase and a lack of intermetallic compounds or eutectic contribute to the high ductility. Furthermore, a higher E{sub corr}, lower I{sub corr} were acquired for better corrosion resistance compared to cast specimens, due to even less composition segregation and more microstructural homogeneity.

36 MATERIALS SCIENCE↗

Mechanical Properties of the Mg-Gd-Y-Zn-Zr Alloys with Different Morphologies of Long-Period Stacking Ordered Phases

Long-period stacking ordered (LPSO) phases with different morphologies and distributions were obtained in the direct chill cast Mg-6.9Gd-3.2Y-1.5Zn-0.5Zr (wt.%) alloy by controlling the homogenization time or cooling rate. Microstructural evolution and the effect of various LPSO phases on the mechanical properties were investigated. There is no obvious α-Mg grain growth during homogenization at 510 °C. Intragranular thin-platelet and coagulated LPSO phases hardly improve the strength but help to develop the ductility. Numerous lamellar phases, which contain “ABCA”-type building blocks with RE and Zn segregation, form during the furnace-cooling process. Lamellar phases, which exhibit lower thermostability compared with the thin-platelet LPSO, slightly improve the tensile yield strength and induce numerous cracks which result in the premature fracture.

36 MATERIALS SCIENCE↗

Powder spreading, densification, and part deformation in binder jetting additive manufacturing

Binder jetting additive manufacturing (AM) can print complex structures in economical and scalable manner. Binder jetting AM comprises of deposition and weak binding of particles, known as green part, at room temperature and subsequent binder removal and sintering densification at high temperatures. However, during the densification (i.e., sintering), the part significantly deforms due to volume shrinkage. The deformation during sintering is difficult to predict, which prevents the widespread application of this technology. In this research, powder spreading simulation using discrete element method (DEM) was performed first to capture local variations in powder bed configuration. Second, finite element method (FEM) with a phenomenological continuum constitutive model was used to predict part shrinkage during the sintering process. DEM simulation showed variations in packing density, particle segregation, formation of uneven powder bed surface, and shift in particle size distribution (PSD). The sintering simulation modeled part deformation with a reasonable accuracy of 3% for solid-state sintering and intermediate liquid phase sintering. A demonstration case with non-uniform initial packing density showed that inhomogeneous green part density and PSD should be accounted for prediction of part deformation in binder jetting AM.

36 MATERIALS SCIENCE↗

Grain-boundary engineering markedly reduces susceptibility to intergranular hydrogen embrittlement in metallic materials

The feasibility of using 'grain-boundary engineering' techniques to reduce the susceptibility of a metallic material to intergranular embrittlement in the presence of hydrogen is examined. Using thermomechanical processing, the fraction of 'special' grain boundaries was increased from 46% to 75% (by length) in commercially pure nickel samples. In the presence of hydrogen concentrations between 1200 and 3400 appm, the high special fraction microstructure showed almost double the tensile ductility; also, the proportion of intergranular fracture was significantly lower and the J{sub c} fracture toughness values were some 20-30% higher in comparison with the low special fraction microstructure. We attribute the reduction in the severity of hydrogen-induced intergranular embrittlement to the higher fraction of special grain boundaries, where the degree of hydrogen segregation at these boundaries is reduced.

36 MATERIALS SCIENCE↗