Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Permeability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Pore-scale multiphase flow modeling and imaging of CO 2 exsolution in Sandstone

This study utilizes synchrotron X-ray micro-tomography and pore scale modeling to investigate the process of gas exsolution and how it affects non-wetting phase relative permeability. Exsolved gas distributions are measured on Domengine and Boise sandstone samples using synchrotron X-ray micro-tomography. Observed gas phase distributions are compared to a new model that simulates the growth and distribution of exsolved gas phase at the pore-scale. Water relative permeability curves are calculated using a Stokes flow simulator with modeled and observed gas distributions, under various conditions, such as rock geometry, and pressure depletion rates. By comparing the actual bubble distributions with modeled distributions, we conclude that exsolved gas is more likely to form and accumulate at locations with higher water velocities. This suggests that convective delivery of CO2 to the gas bubble is a primary mechanism for bubble growth, as compared to diffusive transport through the aqueous phase. For carbonated brine flowing up a fault at half a meter per day, with 5% exsolved gas, the water relative permeability is estimated to be 0.6~0.8 for various sandstones. The reduction of water mobility reduces upward brine migration when even a small amount of exsolution occurs.

58 GEOSCIENCES↗

A hybrid embedded discrete fracture model for simulating tight porous media with complex fracture systems

Numerical simulation considering complex fracture networks in tight oil reservoir becomes a hot issue during these years. Recently, embedded discrete fracture model (EDFM) shows great advantages over the DFM approaches in both calculation efficiency and simplicity of simulation workflow. EDFM has been widely used in tight oil/gas natural energy or enhanced oil recovery (EOR) development. If a large number of small-scale natural fractures exist in reservoir, the calculation efficiency of EDFM method may decrease. A new hybrid simulation model combining the EDFM and dual porosity (DP) model is proposed. The large-scale fractures are dealt with EDFM method while small scale fractures are dealt with DP model. Considering the low permeability of matrix, transient transfer between matrix and natural fracture is considered. The proposed hybrid model is validated compared with the local grid refinement (LGR) model and EDFM-MINC model, and the difference between transient transfer and pseudo-steady-state transfer effect on production is presented. Finally, two test cases are presented, and the sensitivity of some key parameters are investigated. Result shows that the new simulation model has higher calculation efficiency than LGR and EDFM-MINC models. Meanwhile, it honors a good accuracy. The pseudo-steady-state transfer between matrix and natural fracture leads to big error in tight oil production performance analysis both in single phase and two phases flow. Low matrix permeability and big matrix size increase the production difference between pseudo-steady-state transfer and transient transfer models. The proposed model can simulate reservoirs considering stochastic permeability distribution.

58 GEOSCIENCES↗

Mitochondrial aquaporin-8 knockdown in human hepatoma HepG2 cells causes ROS-induced mitochondrial depolarization and loss of viability

Human aquaporin-8 (AQP8) channels facilitate the diffusional transport of H{sub 2}O{sub 2} across membranes. Since AQP8 is expressed in hepatic inner mitochondrial membranes, we studied whether mitochondrial AQP8 (mtAQP8) knockdown in human hepatoma HepG2 cells impairs mitochondrial H{sub 2}O{sub 2} release, which may lead to organelle dysfunction and cell death. We confirmed AQP8 expression in HepG2 inner mitochondrial membranes and found that 72 h after cell transfection with siRNAs targeting two different regions of the human AQP8 molecule, mtAQP8 protein specifically decreased by around 60% (p < 0.05). Studies in isolated mtAQP8-knockdown mitochondria showed that H{sub 2}O{sub 2} release, assessed by Amplex Red, was reduced by about 45% (p < 0.05), an effect not observed in digitonin-permeabilized mitochondria. mtAQP8-knockdown cells showed an increase in mitochondrial ROS, assessed by dichlorodihydrofluorescein diacetate (+ 120%, p < 0.05) and loss of mitochondrial membrane potential (− 80%, p < 0.05), assessed by tetramethylrhodamine-coupled quantitative fluorescence microscopy. The mitochondria-targeted antioxidant MitoTempol prevented ROS accumulation and dissipation of mitochondrial membrane potential. Cyclosporin A, a mitochondrial permeability transition pore blocker, also abolished the mtAQP8 knockdown-induced mitochondrial depolarization. Besides, the loss of viability in mtAQP8 knockdown cells verified by MTT assay, LDH leakage, and trypan blue exclusion test could be prevented by cyclosporin A. Our data on human hepatoma HepG2 cells suggest that mtAQP8 facilitates mitochondrial H{sub 2}O{sub 2} release and that its defective expression causes ROS-induced mitochondrial depolarization via the mitochondrial permeability transition mechanism, and cell death. -- Highlights: ► Aquaporin-8 is expressed in mitochondria of human hepatoma HepG2 cells. ► Aquaporin-8 knockdown impairs mitochondrial H{sub 2}O{sub 2} release and increases ROS. ► Aquaporin-8 knockdown causes ROS-induced mitochondrial depolarization and cell death. ► Mitochondrial permeability transition blockage prevents depolarization and cell death.

60 APPLIED LIFE SCIENCES↗

Use of porcine vaginal tissue ex-vivo to model environmental effects on vaginal mucosa to toxic shock syndrome toxin-1

Menstrual toxic shock syndrome (mTSS) is a rare, recognizable, and treatable disease that has been associated with tampon use epidemiologically. It involves a confluence of microbial risk factors (Staphylococcus aureus strains that produce the superantigen—TSST-1), as well as environmental characteristics of the vaginal ecosystem during menstruation and host susceptibility factors. This paper describes a series of experiments using the well-characterized model of porcine vaginal mucosa ex-vivo to assess the effect of these factors associated with tampon use on the permeability of the mucosa. The flux of radiolabeled TSST-1 and tritiated water ({sup 3}H{sub 2}O) through porcine vaginal mucosa was determined at various temperatures, after mechanical disruption of the epithelial surface by tape stripping, after treatment with surfactants or other compounds, and in the presence of microbial virulence factors. Elevated temperatures (42, 47 and 52 °C) did not significantly increase flux of {sup 3}H{sub 2}O. Stripping of the epithelial layers significantly increased the flux of labeled toxin in a dose-dependent manner. Addition of benzalkonium chloride (0.1 and 0.5%) and glycerol (4%) significantly increased the flux of {sup 3}H{sub 2}O but sodium lauryl sulfate at any concentration tested did not. The flux of the labeled toxin was significantly increased in the presence of benzalkonium chloride but not Pluronic® L92 and Tween 20 and significantly increased with addition of α-hemolysin but not endotoxin. These results show that the permeability of porcine vagina ex-vivo to labeled toxin or water can be used to evaluate changes to the vaginal environment and modifications in tampon materials, and thus aid in risk assessment. - Highlights: • Model assessed local effects of tampon use on vaginal mucosa. • Risks were evaluated using two tracers to assess permeability in an ex vivo model. • Mechanical damage to the epithelial surface increased tracer penetration. • Surfactants increased penetration of tracers across vaginal mucosa. • Alpha-hemolysin increased the penetration of bacterial toxin across vaginal mucosa.

54 ENVIRONMENTAL SCIENCES↗

Lipid rafts regulate PCB153-induced disruption of occludin and brain endothelial barrier function through protein phosphatase 2A and matrix metalloproteinase-2

Occludin is an essential integral transmembrane protein regulating tight junction (TJ) integrity in brain endothelial cells. Phosphorylation of occludin is associated with its localization to TJ sites and incorporation into intact TJ assembly. The present study is focused on the role of lipid rafts in polychlorinated biphenyl (PCB)-induced disruption of occludin and endothelial barrier function. Exposure of human brain endothelial cells to 2,2′,4,4′,5,5′-hexachlorobiphenyl (PCB153) induced dephosphorylation of threonine residues of occludin and displacement of occludin from detergent-resistant membrane (DRM)/lipid raft fractions within 1 h. Moreover, lipid rafts modulated the reduction of occludin level through activation of matrix metalloproteinase 2 (MMP-2) after 24 h PCB153 treatment. Inhibition of protein phosphatase 2A (PP2A) activity by okadaic acid or fostriecin markedly protected against PCB153-induced displacement of occludin and increased permeability of endothelial cells. The implication of lipid rafts and PP2A signaling in these processes was further defined by co-immunoprecipitation of occludin with PP2A and caveolin-1, a marker protein of lipid rafts. Indeed, a significant MMP-2 activity was observed in lipid rafts and was increased by exposure to PCB153. The pretreatment of MMP-2 inhibitors protected against PCB153-induced loss of occludin and disruption of lipid raft structure prevented the increase of endothelial permeability. Overall, these results indicate that lipid raft-associated processes, such as PP2A and MMP-2 activation, participate in PCB153-induced disruption of occludin function in brain endothelial barrier. This study contributes to a better understanding of the mechanisms leading to brain endothelial barrier dysfunction in response to exposure to environmental pollutants, such as ortho-substituted PCBs. - Highlights: • PCB153 disturbed human brain endothelial barrier through disruption of occludin. • Lipid raft-associated PP2A/MMP-2 induced PCB153-induced dysfunction of occludin. • Disrupted lipid rafts modulated PCB153-induced increase of permeability. • Lipid rafts act as a signaling platform for PCB153-induced dysfunction of occludin.

60 APPLIED LIFE SCIENCES↗

Human dermal absorption of chlorinated organophosphate flame retardants; implications for human exposure

Tris-2-chloroethyl phosphate (TCEP), tris (1-chloro-2-propyl) phosphate (TCIPP) and tris-1,3-dichloropropyl phosphate (TDCIPP) are organophosphate flame retardants (PFRs) widely applied in a plethora of consumer products despite their carcinogenic potential. Human dermal absorption of these PFRs is investigated for the first time using human ex vivo skin and EPISKIN™ models. Results of human ex vivo skin experiments revealed 28%, 25% and 13% absorption of the applied dose (500 ng/cm{sup 2}, finite dose) of TCEP, TCIPP and TDCIPP, respectively after 24 h exposure. The EPISKIN™ model showed enhanced permeability values (i.e. weaker barrier), that were respectively 16%, 11% and 9% for TCEP, TCIPP and TDCIPP compared to human ex vivo skin. However, this difference was not significant (P > 0.05). Estimated permeability constants (K{sub p}, cm/h) showed a significant negative correlation with log K{sub ow} for the studied contaminants. The effect of hand-washing on dermal absorption of PFRs was investigated. Washing reduced overall dermal absorption, albeit to varying degrees depending on the physicochemical properties of the target PFRs. Moreover, slight variations of the absorbed dose were observed upon changing the dosing solution from acetone to 20% Tween 80 in water, indicating the potential influence of the dose vehicle on the dermal absorption of PFRs. Finally, estimated dermal uptake of the studied PFRs via contact with indoor dust was higher in UK toddlers (median ΣPFRs = 36 ng/kg bw day) than adults (median ΣPFRs = 4 ng/kg bw day). More research is required to fully elucidate the toxicological implications of such exposure. - Highlights: • Human dermal absorption of PFRs was studied using human ex vivo skin and EPISKIN™. • Absorbed fractions of TCEP, TCIPP and TDCIPP were 28%, 25% and 13% of applied dose. • Permeability constants showed significant negative correlation to log K{sub ow} of PFRs. • Skin washing reduced the overall dermal absorption of target PFRs to varying degrees. • Toddlers are more exposed to PFRs via dermal contact with indoor dust than adults.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design of top covers supporting aerobic in situ stabilization of old landfills - An experimental simulation in lysimeters

Highlights: Black-Right-Pointing-Pointer Tested engineered covers as surrogate to gas extraction during and after in situ aeration. Black-Right-Pointing-Pointer Examined how covers influence gas emissions, water balance and leachate generation. Black-Right-Pointing-Pointer Investigated effect of top covers on air-distribution in waste mass during aeration. Black-Right-Pointing-Pointer We suggest criteria and cover design to meet the demands during and after aeration. Black-Right-Pointing-Pointer Such cover systems may offer greenhouse gas emission reduction also after active aeration. - Abstract: Landfill aeration by means of low pressure air injection is a promising tool to reduce long term emissions from organic waste fractions through accelerated biological stabilization. Top covers that enhance methane oxidation could provide a simple and economic way to mitigate residual greenhouse gas emissions from in situ aerated landfills, and may replace off-gas extraction and treatment, particularly at smaller and older sites. In this respect the installation of a landfill cover system adjusted to the forced-aerated landfill body is of great significance. Investigations into large scale lysimeters (2 Multiplication-Sign 2 Multiplication-Sign 3 m) under field conditions have been carried out using different top covers including compost materials and natural soils as a surrogate to gas extraction during active low pressure aeration. In the present study, the emission behaviour as well as the water balance performance of the lysimeters has been investigated, both prior to and during the first months of in situ aeration. Results reveal that mature sewage sludge compost (SSC) placed in one lysimeter exhibits in principle optimal ambient conditions for methanotrophic bacteria to enhance methane oxidation. Under laboratory conditions the mature compost mitigated CH{sub 4} loadings up to 300 l CH{sub 4}/m{sup 2} d. In addition, the compost material provided high air permeability even at 100% water holding capacity (WHC). In contrast, the more cohesive, mineral soil cover was expected to cause a notably uniform distribution of the injected air within the waste layer. Laboratory results also revealed sufficient air permeability of the soil materials (TS-F and SS-Z) placed in lysimeter C. However, at higher compaction density SS-Z became impermeable at 100% WHC. Methane emissions from the reference lysimeter with the smaller substrate cover (12-52 g CH{sub 4}/m{sup 2} d) were significantly higher than fluxes from the other lysimeters (0-19 g CH{sub 4}/m{sup 2} d) during in situ aeration. Regarding water balance, lysimeters covered with compost and compost-sand mixture, showed the lowest leachate rate (18-26% of the precipitation) due to the high water holding capacity and more favourable plant growth conditions compared to the lysimeters with mineral, more cohesive, soil covers (27-45% of the precipitation). On the basis of these results, the authors suggest a layered top cover system using both compost material as well as mineral soil in order to support active low-pressure aeration. Conventional soil materials with lower permeability may be used on top of the landfill body for a more uniform aeration of the waste due to an increased resistance to vertical gas flow. A compost cover may be built on top of the soil cover underlain by a gas distribution layer to improve methane oxidation rates and minimise water infiltration. By planting vegetation with a high transpiration rate, the leachate amount emanating from the landfill could be further minimised. The suggested design may be particularly suitable in combination with intermittent in situ aeration, in the later stage of an aeration measure, or at very small sites and shallow deposits. The top cover system could further regulate water infiltration into the landfill and mitigate residual CH{sub 4} emissions, even beyond the time of active aeration.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Modeling Gas Flow Dynamics in Metal–Organic Frameworks

Modeling fluid flow dynamics in metal organic frameworks (MOFs) is a required step toward understanding mechanisms of their activity as novel catalysts, sensors, and filtration materials. We adapted a lattice Boltzmann model, previously used for studying flow dynamics in meso- and microporous media, to the nanoscale dimensions of the MOF pores. Using this model, rapid screening of permeability of a large number of MOF structures, in different crystallographic directions, is possible. Here, the method was illustrated here on the example of an anisotropic MOF, for which we calculated permeability values in different flow directions. This method can be generalized to a large class of MOFs and used to design MOFs with the desired gas flow permeabilities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Formation dry-out from CO2 injection into saline acquifers: Part 2, Analytical model for salt precipitation

From a mass balance for water dissolved into the flowing CO{sub 2} stream, and a consideration of saturation profiles from the Buckley-Leverett (1942) fractional flow theory, we derive an equation that directly relates gas saturation S{sub g,d} at the dry-out front to temperature, pressure and salinity dependence of fluid properties. The equation is easily solved by iteration or interpolation. From gas saturation at the front we derive the average gas saturation in the dry-out region, from which we obtain the 'solid saturation' S{sub S}, i.e., the fraction of pore space filled with solid precipitate. Values of S{sub S} derived from this theory show excellent agreement with numerical simulations presented in the preceding companion paper ('Part 1'). Thus, from relative permeabilities and fluid properties at in situ conditions prior to CO{sub 2} injection, it is possible to directly make an accurate estimate of solids precipitation, without having to perform a numerical simulation of the injection process.

54 ENVIRONMENTAL SCIENCES↗

Earthquake Hydrogeology

Hydrologic responses to earthquakes such as streamflow increases, water-level changes, and changes in geyser eruption frequency often reflect changes in permeability caused by seismic waves. The dynamic nature of permeability, as revealed by coseismic hydrologic phenomena, offers implications for groundwater systems, geothermal resources, mineral resources, and geologic hazards. Assessment of water-level responses to solid Earth tides and changes in atmospheric pressure provides a passive way to continuously monitor changes in permeability and storage properties in tectonically active regions.

58 GEOSCIENCES↗

Viscous Behavior of Clay‐Rich Rocks and Its Role in Focused Fluid Flow

Abstract Focused fluid flow is common in sedimentary basins worldwide, where flow structures often penetrate through sandy reservoir rocks, and clay‐rich caprocks. To better understand the mechanisms forming such structures, the impacts of the viscoelastic deformation and strongly nonlinear porosity‐dependent permeability of clay‐rich materials are assessed from an experimental and numerical modeling perspective. The experimental methods to measure the poroviscoelastic and transport properties of intact and remolded shale have been developed, and the experimental data is used to constrain the numerical simulations. It is demonstrated that viscoelastic deformation combined with nonlinear porosity‐dependent permeability triggers the development of localized flow channels, often imaged as seismic chimneys. The permeability inside a channel increases by several orders of magnitude compared to the background values. In addition, the propagation time scale and the channel size strongly depend on the material properties of the fluid and the rock. The time‐dependent behavior of the clay‐rich rock may play a key role in the long‐term integrity of the subsurface formations.

58 GEOSCIENCES↗

Epoxy-based vitrimeric semi-interpenetrating network/MXene nanocomposites for hydrogen gas barrier applications

Herein, we report MXene-filled epoxy-based vitrimeric nanocomposites featuring a semi-interpenetrating network (S-IPN) to develop a hydrogen gas (H 2 ) barrier coating with self-healing characteristics for compressed H 2 storage applications. The reversible epoxy network was formed by synthesizing linear epoxy chains with pendent bis-hydroxyl groups using amino diol, which were then crosslinked with 1,4-benzenediboronic acid to generate dynamic boronic ester linkages. To achieve the S-IPN-type molecular arrangement, the epoxy chains were in situ crosslinked in the presence of poly(ethylene-co-vinyl alcohol) (EVOH), giving rise to a self-healing network (EEP) with a healing efficiency of 87%. Into the S-IPN vitrimer (EEP), a 2D platelet-type nanofiller MXene was incorporated to introduce a tortuous path for H 2 gas diffusion along with improved mechanical properties. The nanocomposite coating was applied to nylon 6 liner material, which is conventionally used in all-composite H 2 storage vessels. Further, the application of a 2 wt% MXene/EEP nanocomposite coating showed a permeability coefficient of 0.062 cm 3 mm m -2 d -1 atm -1 exhibiting ~96% reduction in gas permeability compared to uncoated nylon 6. The same nanocomposite exhibited a healing efficiency of 79%. Increasing the MXene loading to 10 wt% further reduced the permeability coefficient to 0.002 cm 3 mm m -2 d -1 atm -1 ; however, the healing efficiency decreased due to restricted chain mobility. In essence, the current work highlights the potential of vitrimeric S-IPN nanocomposite coatings for H 2 gas-barrier applications, enhancing safety and performance.

42 ENGINEERING↗

Magnetic properties of Fe-rich Fe-V alloy films

Polycrystalline Fe{sub 100-x}V{sub x} with x=0 to 14 at.% V films on a glass substrate were made by the dc magnetron sputtering method. The deposition temperature was 250 deg. C. The magnetic properties, i.e., saturation magnetization 4piM{sub s}, bulk-pinning field for a domain wall H{sub cw}, coercive force H{sub c}, initial permeability mu{sub i}, maximum permeability mu{sub m}, saturation magnetostriction lambda{sub s}, and electrical property, such as the electrical resistivity rho of the Fe-V films, were measured. We find that 4piM{sub s} is a decreasing function of x, H{sub c}, and/or H{sub cw} has a minimum at xapprox =x{sub 0}=8 at. % V, mu{sub i}, mu{sub m}, and/or mu{sub c} has a maximum at x=x{sub 0}, lambda{sub s}approx =0 at x=x{sub 0}, and rho is an increasing function of x. These new magnetic results are consistent with earlier magnetostriction measurements [Jen and Chen, J. Magn. Magn. Mater. 204, 165 (1999)] and theoretical calculations [Ostanin, Staunton, and Razee, Phys. Rev. B 69, 064425 (2004)]. Moreover, all the magnetic features in the x dependence of H{sub c}, H{sub cw}, mu{sub i}, mu{sub m}, mu{sub c}, and lambda{sub s}, respectively, can be explained within the framework of the bulk-pinning (or surface-pinning) and the end-pinning (or nucleation) models. Briefly, the pinning model analysis of the magnetic hysteresis data confirms the inference that near zero lambda{sub s} implies maximal permeabilities and smallest H{sub c} and H{sub cw}. Among all the Fe-V films, the Fe{sub 92}V{sub 8} film has the optimal magnetic and electrical properties for application.

36 MATERIALS SCIENCE↗

Magnetic softness and high-frequency characteristics of Fe{sub 65}Co{sub 35}-O alloy films

The effects of oxygen concentration and film thickness were studied on the microstructural, electrical, and magnetic properties of Fe{sub 65}Co{sub 35}-O alloy films prepared by dc magnetron sputtering at room temperature. The films showed the best magnetic softness with a large saturation magnetization of 21.5 kG, low coercivities of 2.8 and 2.1 Oe in easy and hard axes, respectively, and a high resistivity of 2215 muOMEGA cm at an optimized condition of an oxygen gas flow ratio of 1.0% and a film thickness of 105 nm. Such an excellent magnetic softness can be attributed to grain refinement caused by the addition of very low dose of oxygen, which basically did not lead to the full formation of Fe and/or Co oxide phases with low saturation magnetizations. The microwave permeability measurement indicated that the addition of very low dose of oxygen could improve the response of real permeability to frequency. A high real permeability of 525 at frequency up to 1.2 GHz was obtained for the Fe{sub 65}Co{sub 35}-O films deposited at the optimized condition above.

36 MATERIALS SCIENCE↗

Angular dependence of dynamic magnetic properties and magnetization orientation distribution of thin films

The angular dependence of dynamic magnetic properties of FeTaN thin films fabricated by rf sputtering deposition technique onto various substrates was investigated in conjunction with static magnetic characteristics. Thin films grown onto rigid and thick substrates show a well-defined uniaxial anisotropy and strongly distinct permeability spectra measured at various orientations while those samples grown onto flexible and thin substrates exhibit a less well-defined uniaxial anisotropy and much less different permeability spectra. The resultant variation of the magnetization orientation distributions obtained by retrieving the magnetization values from the permeability curves for different substrates can be interpreted in terms of the magnetic anisotropy dispersion due to stress.

36 MATERIALS SCIENCE↗

High frequency characteristics of FeCoAlO thin films combined the effects of stress and magnetic field

The soft magnetic FeCoAlO thin films with different response at high frequency were prepared by using RF magnetron sputtering. Two different configurations of the sputtering targets were used: the Al{sub 2}O{sub 3} chips were placed on Fe{sub 70}Co{sub 30} disk either uniformly dispersed on the sputtering area (Target-A) or dispersed on the half side of the sputtering area (Target-B). It was found that, although, the films deposited from both of Target A and B possessed good soft magnetic properties and in-plane uniaxial magnetic anisotropy, they showed different behaviors at high frequency. The films deposited by using Target-A have mean permeability of 500 and a cut-off frequency (f{sub r}) of around 780 MHz, while the films deposited by using Target-B have mean permeability of 200 and a f{sub r} of 3.4 GHz. The higher f{sub r} of the later corresponds to the higher uniaxial anisotropic field in the films deposited by using the Target-B, which due to an extra anisotropy induced by the stress resulted from gradient of the Al-O composition. By adjusting the configuration of Target-B, the permeability and f{sub r} can be tuned to satisfy the different requirements for certain industrial applications.

36 MATERIALS SCIENCE↗

Morphology and properties of recycled polypropylene/bamboo fibers composites

Polypropylene (PP) is among the most widely used thermoplastics in many industrial fields. However, like other recycled polymers, its properties usually decrease after recycling process and sometimes are degraded to poor properties level for direct re-employment. The recycled products, in general, need to be reinforced to have competitive properties. Short bamboo fibers (BF) have been added in a recycled PP (RPP) with and without compatibilizer type maleic anhydride polypropylene (MAPP). Several properties of composite materials, such as helium gas permeability and mechanical properties before and after ageing in water, were examined. The effects of bamboo fiber content and fiber chemical treatment have been also investigated. We showed that the helium permeability increases if fiber content is higher than 30% because of a poor adhesion between untreated bamboo fiber and polymer matrix. The composites reinforced by acetylated bamboo fibers show better helium permeability due to grafting of acetyl groups onto cellulose fibers surface and thus improves compatibility between bamboo fibers and matrix, which has been shown by microscopic observations. Besides, mechanical properties of composite decrease with ageing in water but the effect is less pronounced with low bamboo fiber content.

36 MATERIALS SCIENCE↗

Improvement of high-frequency characteristics of Z-type hexaferrite by dysprosium doping

Z-type hexaferrite has great potential applications as anti-EMI material for magnetic devices in the GHz region. In this work, Dy-doped Z-type hexaferrites with nominal stoichiometry of Ba{sub 3}Co{sub 2}Dy{sub x}Fe{sub 24-x}O{sub 41} (x 0.0, 0.05, 0.5, 1.0) were prepared by an improved solid-state reaction method. The effects of rare earth oxide (Dy{sub 2}O{sub 3}) addition on the phase composition, microstructure and electromagnetic properties of the ceramics were investigated. Structure and micromorphology characterizations indicate that certain content of Dy doping will cause the emergence of the second phase Dy{sub 3}Fe{sub 5}O{sub 12} at the grain boundaries of the majority phase Z-type hexaferrite, due to which the straightforward result is the grain refinement during the successive sintering process. Permeability spectra measurements show that the initial permeability reaches its maximum of 17 at 300 MHz with x = 0.5, while the cutoff frequency keeps above 800 MHz. The apparent specific anisotropy field H{sub K} of Dy-doped Z-type hexaferrites decreases with x increasing. The relationships among phase composition, grain size, permeability spectra, and anisotropy are theoretically investigated, and according to the analysis, Dy doping effects on its magnetic properties can be well explained and understood.

36 MATERIALS SCIENCE↗