Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laser Material Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Passivation layer breakdown during laser-fired contact formation for photovoltaic devices

Low resistance laser-fired ohmic contacts (LFCs) can be formed on the backside of Si-based solar cells using microsecond pulses. However, the impact of these longer pulse durations on the dielectric passivation layer is not clear. Retention of the passivation layer during processing is critical to ensure low recombination rates of electron-hole pairs at the rear surface of the device. In this work, advanced characterization tools are used to demonstrate that although the SiO{sub 2} passivation layer melts directly below the laser, it is well preserved outside the immediate LFC region over a wide range of processing parameters. As a result, low recombination rates at the passivation layer/wafer interface can be expected despite higher energy densities associated with these pulse durations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spatial coherence measurements of non-resonant and resonant high harmonics generated in laser ablation plumes

We present measurements of the spatial coherence of the high-order harmonics generated in laser-produced ablation plumes. Harmonics were generated using 4 fs, 775 nm pulses with peak intensity 3 × 10{sup 14} W cm{sup −2}. Double-slit fringe visibilities in the range of ≈0.6–0.75 were measured for non-resonant harmonics in carbon and resonantly enhanced harmonics in zinc and indium. These are somewhat higher than the visibility obtained for harmonics generated in argon gas under similar conditions. This is attributed to lower time-dependent ionization of the plasma ablation targets compared to argon during the high harmonics generation process.

36 MATERIALS SCIENCE↗

Spatially Precise Light‐Activated Dedoping in Wafer‐Scale MoS 2 Films

2D materials, particularly transition metal dichalcogenides (TMDCs), have shown great potential for microelectronics and optoelectronics. However, a major challenge in commercializing these materials is the inability to control their doping at a wafer scale with high spatial fidelity. Interface chemistry is used with the underlying substrate oxide and concomitant exposure to visible light in ambient conditions for photo-dedoping wafer scale MoS 2 . It is hypothesized that the oxide layer traps photoexcited holes, leaving behind long-lived electrons that become available for surface reactions with ambient air at sulfur vacancies (defect sites) resulting in dedoping. Additionally, high fidelity spatial control is showcased over the dedoping process, by laser writing, and fine control achieved over the degree of doping by modulating the illumination time and power density. This localized change in MoS 2 doping density is very stable (at least 7 days) and robust to processing conditions like high temperature and vacuum. The scalability and ease of implementation of this approach can address one of the major issues preventing the “Lab to Fab” transition of 2D materials and facilitate its seamless integration for commercial applications in multi-logic devices, inverters, and other optoelectronic devices.

14 SOLAR ENERGY↗

Rapid surface hardening and enhanced tribological performance of 4140 steel by friction stir processing

Tribological performance of steel materials can be substantially enhanced by various thermal surface hardening processes. For relatively low-carbon steel alloys, case carburization is often used to improve surface performance and durability. If the carbon content of steel is high enough (>0.4%), thermal treatments such as induction, flame, laser, etc. can produce adequate surface hardening without the need for surface compositional change. This paper presents an experimental study of the use of friction stir processing (FSP) as a means to hardened surface layer in AISI 4140 steel. The impacts of this surface hardening process on the friction and wear performance were evaluated under both dry and lubricated contact conditions in reciprocating sliding. FSP produced the same level of hardening and superior tribological performance when compared to conventional thermal treatment, using only 10% of the energy and without the need for quenching treatments. With FSP surface hardness of about 7.8 GPa (62 Rc) was achieved while water quenching conventional heat treatment produced about 7.5 GPa (61 Rc) hardness. Microstructural analysis showed that both FSP and conventional heat treatment produced martensite. Although the friction behavior for FSP treated surfaces and the conventional heat treatment were about the same, the wear in FSP processed surfaces was reduced by almost 2× that of conventional heat treated surfaces. Furthermore, the superior performance is attributed to the observed grain refinement accompanying the FSP treatment in addition to the formation of martensite. As it relates to tribological performance, this study shows FSP to be an effective, highly energy efficient, and environmental friendly (green) alternative to conventional heat treatment for steel.

36 MATERIALS SCIENCE↗

ClusterBoron Implant Alternative to BF{sub 2} PMOS SDE

As device geometries scale, the formation of the SDE becomes increasingly difficult and increasingly important. For advanced technologies, new methods such as ultra-low-energy boron implantation and millisecond annealing (flash or laser) are necessary to achieve the required junction characteristics. In addition, these processes must be compatible with the remainder of the process flow, which might include advanced dielectrics, stress technologies, SOI, etc. The emergence of ClusterBoron as a high productivity alternative for the low energy implant creates interest in device performance possible in a realistic process flow. This paper will present an evaluation of the use of ClusterBoron for the PMOS SDE in an advanced 65 nm logic process which includes laser annealing, e-SiGe stress layers and SOI. The conventional process uses a BF2 SDE process. Complete device characteristics will be shown comparing the ClusterBoron SDE to the conventional BF2. It will be shown that the ClusterBoron process achieves better boron activation, leading to enhanced transistor drive current. It will also be shown that the ClusterBoron is compatible with the SiGe stress layers and SOI structure. In summary, ClusterBoron presents an attractive alternative to the conventional BF2 process for advanced PMOS SDE.

36 MATERIALS SCIENCE↗

High-Strain Rate Spall Strength Measurement for CoCrFeMnNi High-Entropy Alloy

In this study, we experimentally investigate the high stain rate and spall behavior of Cantor high-entropy alloy (HEA), CoCrFeMnNi. First, the Hugoniot equations of state (EOS) for the samples are determined using laser-driven CoCrFeMnNi flyers launched into known Lithium Fluoride (LiF) windows. Photon Doppler Velocimetry (PDV) recordings of the velocity profiles find the EOS coefficients using an impedance mismatch technique. Following this set of measurements, laser-driven aluminum flyer plates are accelerated to velocities of 0.5–1.0 km/s using a high-energy pulse laser. Upon impact with CoCrFeMnNi samples, the shock response is found through PDV measurements of the free surface velocities. From this second set of measurements, the spall strength of the alloy is found for pressures up to 5 GPa and strain rates in excess of 106 s−1. Further analysis of the failure mechanisms behind the spallation is conducted using fractography revealing the occurrence of ductile fracture at voids presumed to be caused by chromium oxide deposits created during the manufacturing process.

36 MATERIALS SCIENCE↗

NASA Tech Briefs, July 2012

Topics covered include: Instrument Suite for Vertical Characterization of the Ionosphere-Thermosphere System; Terahertz Radiation Heterodyne Detector Using Two-Dimensional Electron Gas in a GaN Heterostructure; Pattern Recognition Algorithm for High-Sensitivity Odorant Detection in Unknown Environments; Determining Performance Acceptability of Electrochemical Oxygen Sensors; Versatile Controller for Infrared Lamp and Heater Arrays; High-Speed Scanning Interferometer Using CMOS Image Sensor and FPGA Based on Multifrequency Phase-Tracking Detection; Ultra-Low-Power MEMS Selective Gas Sensors; Compact Receiver Front Ends for Submillimeter-Wave Applications; Dynamically Reconfigurable Systolic Array Accelerator; Blocking Losses With a Photon Counter; Motion-Capture-Enabled Software for Gestural Control of 3D Mod; Orbit Software Suite; CoNNeCT Baseband Processor Module Boot Code SoftWare (BCSW); Trajectory Software With Upper Atmosphere Model; ALSSAT Version 6.0; Employing a Grinding Technology to Assess the Microbial Density for Encapsulated Organisms; Demonstration of Minimally Machined Honeycomb Silicon Carbide Mirrors; Polyimide Aerogel Thin Films; Nanoengineered Thermal Materials Based on Carbon Nanotube Array Composites; Composite Laminate With Coefficient of Thermal Expansion Matching D263 Glass; Robust Tensioned Kevlar Suspension Design; Focal Plane Alignment Utilizing Optical CMM; Purifying, Separating, and Concentrating Cells From a Sample Low in Biomass; Virtual Ultrasound Guidance for Inexperienced Operators; Beat-to-Beat Blood Pressure Monitor; Non-Contact Conductivity Measurement for Automated Sample Processing Systems; An MSK Radar Waveform; Telescope Alignment From Sparsely Sampled Wavefront Measurements Over Pupil Subapertures; Method to Remove Particulate Matter from Dusty Gases at Low Pressures; Terahertz Quantum Cascade Laser With Efficient Coupling and Beam Profile; Measurement Via Optical Near-Nulling and Subaperture Stitching; 885-nm Pumped Ceramic Nd:YAG Master Oscillator Power Amplifier Laser System; Airborne Hyperspectral Imaging System; Heat Shield Employing Cured Thermal Protection Material Blocks Bonded in a Large-Cell Honeycomb Matrix; and Asymmetric Supercapacitor for Long-Duration Power Storage.

Source record↗

Growth of (111) oriented NiFe{sub 2}O{sub 4} polycrystalline thin films on Pt (111) via sol-gel processing

Polycrystalline NiFe{sub 2}O{sub 4} (NFO) thin films are grown on (111) platinized Si substrates via chemical solution processing. {theta}-2{theta} x-ray diffraction, x-ray pole figures and electron diffraction indicate that the NFO has a high degree of <111> uniaxial texture normal to the film plane. The texturing is initiated by nucleation of (111) planes at the Pt interface and is enhanced with decreasing film thickness. As the NFO magnetic easy-axis is <111>, the out-of-plane magnetization exhibits improved M{sub r}/M{sub s} and coercivity with respect to randomly oriented films on silicon substrates. The out-of-plane M{sub r}/M{sub s} ratio for (111) textured NFO thin film is improved from 30% in 150 nm-thick films to above 70% in 50 nm-thick films. The improved out-of-plane magnetic anisotropy is comparable to epitaxial NFO films of comparable thickness deposited by pulsed laser deposition and sputtering.

36 MATERIALS SCIENCE↗

High temperature tensile properties of H13 tool steel fabricated via binder jet additive manufacturing

H13 is one of the most used steels for hot work tooling applications like die casting. Binder jet additive manufacturing (BJAM) offers a cost-effective solution to fabricate tools with performance enhancing features like internal cooling channels. While full densification of BJAM H13 has been demonstrated in the literature, the room and high temperature tensile properties of the material, and the effect of post-process treatments like hot isostatic pressing (HIP), and heat treatment (HT) are unknown. Here we use HIP+HT to obtain a combination of ultimate tensile strength (UTS) and elongation to failure that is superior to H13 fabricated via laser powder bed fusion and wire arc additive manufacturing. HIP+HT BJAM H13 has a superior UTS (1836 MPa) compared with conventionally processed (1671 MPa) H13 but has lower plastic elongation. We report that as-sintered samples have an extensive network of continuous grain boundary (GB) carbides that contribute to brittle fracture. HIP+HT results in partial dissolution of GB carbides and formation of a fine martensitic microstructure resulting in superior tensile strength and elongation compared with as-sintered H13. We use thermo-kinetic calculations to rationalize the effects of HIP+HT on microstructure and properties.

36 MATERIALS SCIENCE↗

Oxygen-assisted multipass cutting of carbon fiber reinforced plastics with ultra-short laser pulses

Deep multipass cutting of bidirectional and unidirectional carbon fiber reinforced plastics (CFRP) with picosecond laser pulses was investigated in different static atmospheres as well as with the assistance of an oxygen or nitrogen gas flow. The ablation rate was determined as a function of the kerf depth and the resulting heat affected zone was measured. An assisting oxygen gas flow is found to significantly increase the cutting productivity, but only in deep kerfs where the diminished evaporative ablation due to the reduced laser fluence reaching the bottom of the kerf does not dominate the contribution of reactive etching anymore. Oxygen-supported cutting was shown to also solve the problem that occurs when cutting the CFRP parallel to the fiber orientation where a strong deformation and widening of the kerf, which temporarily slows down the process speed, is revealed to be typical for processing in standard air atmospheres.

36 MATERIALS SCIENCE↗

Search for 3D topological superconductors using laser-based spectroscopy (Final Technical Report)

The three-dimensional topological superconductor (3D TSC) is a novel quantum phase of matter that is predicted to exhibit exotic thermal and electrical properties, which may serve applications ranging from precision thermal management and sensing technologies to fault-tolerant quantum information processing. Over the past decade, there has been an intensive effort to realize 1D and 2D TSCs by artificially engineering them from combinations of already existing materials. For example, coupling conventional superconductors to spin-orbit coupled 1D nanowires or to 2D topological insulator surfaces by the proximity effect provides a route to realizing 1D and 2D TSCs respectively. However no artificial engineering strategy is available for a 3D TSC. Therefore, current searches are limited to intrinsically superconducting compounds whose topological properties are difficult to predict. The overarching goal of this project was to realize and to identify 3D TSCs in bulk single crystals using novel laser-based spectroscopic techniques. One major thrust was to develop ultralow temperature and ultra-high-resolution angle-resolved photoemission spectroscopy (ARPES) to directly measure the dispersion of Majorana excitations that are predicted to exist on the surfaces of 3D TSCs. Another major thrust was to develop a rational route to realize 3D TSCs by identifying their precursor phases. It is theoretically proposed that the critical fluctuations of certain ordered electronic phases can mediate Cooper pairing in odd-parity channels and lead to topological superconductivity. Therefore, 3D TSCs may potentially emerge upon suppressing these inversion symmetry broken precursor phases to a critical point with external perturbations such as pressure, strain or even light. To test this hypothesis, we studied candidate materials using a suite of symmetry-sensitive optical probes including rotational anisotropy optical second harmonic generation (RA-SHG) and time-resolved coherent phonon spectroscopy, all operable under high-pressure and low temperature environments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Intense 1.54 {mu}m fluorescence of Er{sup 3+}/Yb{sup 3+} codoped phosphate glass and the three-photon phenomenon of near infrared upconversion luminescence

Transparent P{sub 2}O{sub 5}-CaO-Na{sub 2}O glasses codoped with Er{sup 3+} and Yb{sup 3+} ions were fabricated by high-temperature melting technique. Strong near infrared and visible upconversion luminescence were observed under 975 nm laser diode excitation, and the luminescence processes were explained in details. For 1.54 {mu}m band, the calculated peak emission cross sections is 1.04x10{sup -20} cm{sup 2}, and it is better than that in germinate, tellurite, silicate, and other phosphate glasses. The near infrared upconversion emission around 828 nm contains two-photon and three-photon processes, and it is attributed to the transition {sup 4}S{sub 3/2}{yields}{sup 4}I{sub 13/2}, which enhances the population of the upper level for 1.54 {mu}m laser emission and reduces the energy loss due to upconversion. Efficient near infrared fluorescence indicates Er{sup 3+}/Yb{sup 3+} codoped phosphate glass is a promising laser and amplifier material.

36 MATERIALS SCIENCE↗

Influence of the Mg-content on the cation distribution in cubic Mg{sub x}Fe{sub 3-x}O{sub 4} nanoparticles

The influence of the Mg-content on the structural and magnetic properties of cubic Mg{sub x}Fe{sub 3-x}O{sub 4} nanoparticles prepared by combustion reaction was investigated using X-ray diffraction, transmission electron microscopy (TEM), Moessbauer spectroscopy, and Raman spectroscopy. Lattice parameter, nanoparticle size, and cation (Mg{sup 2+}, Fe{sup 3+}) distribution were quantified as a function of the Mg-content in the range 0.5<=x<=1.5. We found a mixed-like spinel structure at the smaller x-value end whereas the inverse-like spinel structure dominates samples with larger x-values. Moreover, in the x-value range investigated (0.5<=x<=1.5) we found no change in the quadrupole splitting and isomer shift values, though the hyperfine field decreases as the x-value increases. The splitting of the A{sub 1g} Raman mode was used to both quantify the Mg{sup 2+}/Fe{sup 3+} contents in the tetrahedral site and obtain the cation distribution in the Mg{sub x}Fe{sub 3-x}O{sub 4} structure. The cation distribution obtained from the Raman data is in very good agreement with the cation distribution obtained from the Moessbauer data. - Abstract: Raman spectra of Mg{sub x}Fe{sub 3-x}O{sub 4} samples (x=0.5, 1.0, and 1.5) using the Ar{sup +} 514.5 nm laser line. Display Omitted

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of pH on the quantum-size-controlled photoelectrochemical etching of epitaxial InGaN quantum dots

Illumination by a narrow-band laser has been shown to enable photoelectrochemical (PEC) etching of InGaN thin films into quantum dots with sizes controlled by the laser wavelength. Here, we investigate and elucidate the influence of solution pH on such quantum-size-controlled PEC etch process. We find that although a pH above 5 is often used for PEC etching of GaN-based materials, oxides (In 2 O 3 and/or Ga 2 O 3 ) form which interfere with quantum dot formation. Furthermore, at pH below 3, however, oxide-free QDs with self-terminated sizes can be successfully realized.

36 MATERIALS SCIENCE↗

Ultraviolet laser ablation of polycarbonate and glass in air

The fundamental physical processes that follow ultraviolet laser ablation of polycarbonate and borosilicate glass in air have been investigated using photodeflection as a function of the distance from the surface to probe laser. Four features were observed in the data sets for each material. Two of these features correlate well with gas dynamical predictions for the expansion of the shock wave and gas plume. The third feature is consistent with the propagation of the popping sound of the laser ablation event. The final feature, which occurs at very early times and does not shift significantly in time as the surface to probe distance is increased from 0 to greater than 6 mm, has been tentatively ascribed to the ejection of fast electrons. The final significant observation is complete blocking of the probe laser, only observed during borosilicate ablation, which is attributed to scattering of the probe laser light by macroscopic SiO{sub x} particles that grow in the final stages of plume expansion and cooling.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Preparation For Laser Wakefield Experiments Driven by the Texas Petawatt Laser System

Laboratories around the world are planning petawatt laser driven experiments. The Texas petawatt laser offers the ability to demonstrate laser wake field acceleration (LWFA) in a unique regime with pulse duration ({approx}160 fs) shorter than other petawatt scale systems currently in operation or under development. By focusing the 1.25 PW, 200 J, 160 fs pulses to peak intensity {approx}10{sup 19} W/cm{sup 2}, multi-GeV electron bunches can be produced from a low density He gas jet. The rarefied plasma density (5x10{sup 16}-10{sup 17} cm{sup -3}) required for near-resonant LWFA minimizes plasma lensing and offers long dephasing length for electron acceleration over distances ({approx}10 cm) exceeding the Rayleigh range. Because of the high power, the laser can be focused to a spot (r{sub 0}{approx}100 microns) greater than the plasma wavelength (r{sub 0}>{lambda}{sub p}), thus minimizing radial propagation effects. Together these properties enable the laser pulse to self-guide without the use of a preformed channel lending simplicity and stability to the overall acceleration process. Particle-in-cell (PIC) simulations show the laser experiences self-focusing which, because of ultrashort pulse duration, does not lead to a collapse of the wakefield and can generate over 3 GeV electron energy. The presented material will include details of initial measurements of the Texas petawatt laser system, simulations of laser wakefield acceleration for the given laser parameters and the experimental setup currently under construction.

36 MATERIALS SCIENCE↗

Heating dynamics of CO{sub 2}-laser irradiated silica particles with evaporative shrinking: Measurements and modeling

The heating dynamics of CO{sub 2}-laser heated micron-sized particles were determined for temperatures <3500 K measured using infrared imaging. A coupled mass and energy conservation model is derived to predict single particle temperatures and sizes, which were compared with data from particles deposited on non-absorbing substrates to assess the relevant heat transfer processes. Analysis reveals substrate conduction dominates all other heat losses, while laser absorption determined from Mie theory is strongly modulated by particle evaporative shrinking. This study provides insights into the light coupling and heating of particle arrays where the material optical properties are temperature-dependent and particle size changes are significant.

36 MATERIALS SCIENCE↗

Experimental comparison of laser energy losses in high-quality laser-oxygen cutting of low-carbon steel using radiation from fibre and CO{sub 2} lasers

We report a comparative experimental study of laseroxygen cutting of low-carbon steel using a fibre laser with a wavelength of 1.07 μm and a CO{sub 2} laser with a wavelength of 10.6 μm at the sheet thickness of 3 – 16 mm. For the two lasers we have measured the dependence of the cutting speed on the radiation power and determined the cutting speed at which the surface roughness is minimal. The coefficient of laser radiation absorption in the laser cutting process is measured for these lasers at different values of the cutting speed and radiation power. It is found that the minimal roughness of the cut surface is reached at the absorbed laser energy per unit volume of the removed material, equal to 11 – 13 J mm{sup -3}; this value is the same for the two lasers and does not depend on the sheet thickness. (laser technologies)

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗