Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Inlet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Performance of a V/STOL tilt nacelle inlet with blowing boundary layer control

A scale model of a V/STOL tilt nacelle fitted to a 0.508 m single stage fan was tested in the NASA Lewis 9x15 ft low speed wind tunnel to determine the effect of diffuser blowing on the inlet aerodynamics and aeromechanical performance. The test was conducted over a range of freestream speeds (up to 120 knots) and angles of attack (up to 120 deg). Diffuser blowing had a beneficial affect on all performance parameters. The angle of attack range for separation free flow substantially increased, and the fan face distortion significantly reduced with a corresponding increase in total pressure recovery. Discrete narrow band blade stress peaks which were common to the nonblowing (baseline) configuration were eradicated with diffuser blowing.

Johns, A. L.↗
NASA NTRS1979

An experimental study of sound radiation from hyperboloidal inlet ducts

Sound radiation from hyperboloidal inlet ducts which include a circular cylinder with plane baffle as a limiting case was investigated. Results include the polar angle variation of the pressure level and the phase of the radiated field for various frequencies and various modes incident which were produced using an electronically operated mode synthesizer. Good agreement with a rigorous theoretical prediction was found.

Clark, L. R.↗
NASA NTRS1979

Analysis, design, and test of acoustic treatment in a laboratory inlet duct

A suppression prediction program based on the method of modal analysis for spinning mode propagation in a circular duct was used in the analytical design of optimized, multielement, Kevlar bulk-absorber treatment configurations for an inlet duct. The NASA-Langley ANRL anechoic chamber using the spinning mode synthesizer as a sound source was used to obtain in-duct spinning mode measurements, radial mode measurements, and far-field traverses, as well as aerodynamic measurements. The measured suppression values were compared to predicted values, using the in-duct, forward-traveling, radial-mode content as the source for the prediction. The performance of the treatment panels was evaluated from the predicted and measured data. Although experimental difficulties were encountered at the design condition, sufficient information was obtained to confirm the expectation that it is the panel impedance components which are critical to suppression at a single frequency, not the particular construction materials. The agreement obtained between measurement and prediction indicates that the analytical program can be used as an accurate, reliable, and useful design tool.

Kraft, R. E.↗
NASA NTRS1979

Effect of rotor meridional velocity ratio on response to inlet radial and circumferential distortion

Three single transonic fan stages, each having a different meridional velocity ratio across its rotor, were tested with two magnitudes of tip radial distortion and with a 90 deg circumferential distortion imposed on the inlet flow. The rotor with the lowest meridional velocity ratio (less than 0.9 at the tip) demonstrated the least degradation of performance due to these distortions. Loss and deviation angle data (as needed for performance prediction with radial distortion) calculated along actual streamlines for radially distorted flow and correlated against diffusion factor, showed consistent agreement with data calculated along design streamlines for undistorted flow.

Sanger, N. L.↗
NASA NTRS1978

Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades

A procedure is presented for predicting the magnitude of the turbine inlet gas temperatures potentially achievable using first generation tungsten fiber reinforced superalloys (TFRS) turbine blades. Both uncoated blades and blades with thermal barrier coatings are considered. The thermal conductivities of two representative TFRS were measured over a range of temperatures. The results show that cooled TFRS blades may allow significantly higher gas temperatures than are possible with superalloy blades. For one design, the difference is about 150-200 K.

Winsa, E. A.↗
NASA NTRS1979

Full-scale engine tests of bulk absorber acoustic inlet treatment

Three different densities of Kevlar bulk absorber fan inlet treatment were tested on a YF 102 turbofan engine. This bulk absorber material may have potential for flight application. Far-field noise measurements were made and the attenuation properties of the three treatment densities were compared. In addition the best bulk treatment was compared to the best single degree of freedom, SDOF (honeycomb and perforated cover sheet) treatment from another investigation. Although the density was varied over a large range, (3 to 1) the effect on attenuation was small. The highest density treatment, 11.8 lb/cu ft, had a somewhat broader attenuation bandwidth. The comparison of the best bulk and SDOF treatments showed the bulk to have a greater attenuation bandwidth. At the design frequency both types of treatment had almost equal performance.

Heidelberg, L. J.↗
NASA NTRS1979

Performance of a V/STOL tilt nacelle inlet with blowing boundary layer control

A scale model of a V/STOL tilt nacelle fitted to a 0.508 m single stage fan was tested in the NASA Lewis low speed wind tunnel to determine the effect of diffuser blowing on the inlet aerodynamics and aeromechanical performance. The test was conducted over a range of freestream speeds (up to 120 knots) and angles-of attack (up to 120 deg). In general, diffuser blowing had a beneficial affect on all performance parameters. The angle-of-attack range for a separation-free flow substantially increased, and the fan face distortion reduced with a corresponding increase in total pressure recovery. Discrete narrow band blade stress peaks which were common to the nonblowing (baseline) configuration were eradicated with diffuser blowing.

Johns, A. L.↗
NASA NTRS1980

Calculation of two-dimensional inlet flow fields in a supersonic free stream by an implicit marching code with nonorthogonal mesh generation: User's manual

An implicit, shock-capturing finite-difference code which is used to calculate two-dimensional inlet flow fields in a supersonic free stream is explained. The Euler equations are subjected to general nonorthogonal transformation and a body-fitted coordinate system is employed. The mathematical formulation of the problem is given along with the numerical algorithm. Initial and boundary conditions, numerical stability, program limitations, and accuracy is discussed. An overall program logic as well as instructions for program use and operation are also furnished.

Biringen, S. H.↗
NASA NTRS1980

Experimental evaluation of a spinning-mode acoustic-treatment design concept for aircraft inlets

An aircraft-inlet noise suppressor method based on mode cutoff ratio was qualitatively checked by testing a series of liners on a YF-102 turbofan engine. Far-field directivity of the blade passing frequency was used extensively to evaluate the results. The trends and observations of the test data lend much qualitative support to the design method. The best of the BPF liners attained a suppression at design frequency of 19 dB per unit length-diameter ratio. The best multiple-pure-tone linear attained a remarkable suppression of 65.6 bB per unit length-diameter ratio.

Heidelberg, L. J.↗
NASA NTRS1980

Computation of three-dimensional viscous supersonic flow in inlets

A new approach has been developed for the computation of the three-dimensional viscous supersonic flow with embedded subsonic regions adjacent to solid boundaries and is applied to a mixed-compression supersonic inlet typical of current designs. The approach uses a reduced form of the three-dimensional Navier-Stokes equations so that the resultant equations can be treated as an initial boundary value problem and thus be solved by non-iterative forward marching in space. The numerical procedure utilizes an efficient consistently-split linearized block implicit technique to solve the finite difference analogues to the set of governing partial differential equations.

Buggeln, R. C.↗
NASA NTRS1981

Measurements of laminar and turbulent flow in a curved duct with thin inlet boundary layers

Laser Doppler velocimetry was used to measure the laminar and turbulent flow in a 90 deg square bend of strong curvature. The boundary layers at the inlet to the bend were approximately 25 percent and 15 percent of the hydraulic diameter for the laminar and turbulent flows, respectively. The development of the pressure driven secondary motion is more rapid for laminar flow: the maximum cross stream component measured was 60 percent of the bulk velocity in contrast to 40 percent for turbulent flow. The streamwise isotachs show that, for laminar flow, large velocities are found progressively nearer to the outer radius of the bend and along the sidewalls. For turbulent flow, the isotachs move towards the inner radius until about 60 deg around the bend where strong secondary motion results in a similar redistribution. Turbulence level and shear stress measurements are also presented.

Taylor, A. M. K. P.↗
NASA NTRS1981

Some flow phenomena associated with aligned, sequential apertures with Borda-type inlets

Choked flow rate and pressure profile data were taken and studied for a configuration consisting of four axially aligned, sequential Borda tubes of 1.9 length diameter ratio with separation distances of 0.8 and 30 tube diameters. For either case the flow rate data could be represented by a flow coefficient reduced temperature plot. At a separation distance of 30 tube diameters the pressure profiles dropped sharply at the entrance and recovered within each Borda tube; except at low temperatures, where fluid jetting through the last Borda tube occurred. At a separation distance of 0.8 tube jetting was prevalent, and application of a significant backpressure did not alter the jetting. These results agree with other data for tubes with Borda or sharp edge orifice inlets and with a water flow visualization study reported herein.

Hendericks, R. C.↗
NASA NTRS1981

Effect of a part-span variable inlet guide vane on the performance of a high-bypass turbofan engine

The ability of a part span variable inlet guide vane (VIGV) to modulate the thrust of a high bypass turbofan engine was evaluated at altitude/Mach number conditions of 4572 m/0.6 and 9144 m/0.93. Fan tip, gas generator and supercharger performance were also determined, both on operating lines and during fan duct throttling. The evaluation was repeated with the bypass splitter extended forward to near the fan blade trailing edge. Gross thrust attentuation of over 50 percent was achieved with 50 degree VIGV closure at 100 percent corrected fan speed. Gas generator supercharger performance fell off with VIGV closure, but this loss was reduced when a splitter extension was added. The effect of VIVG closure on gas generator performance was minimal.

Bobula, G. A.↗
NASA NTRS1981

Acoustic performance of inlet suppressors on an engine generating a single mode

Three single degree of freedom liners with different open area ratio face sheets were designed for a single spinning mode in order to evaluate an inlet suppressor design method based on mode cutoff ratio. This mode was generated by placing 41 rods in front of the 28 blade fan of a JT15D turbofan engine. At the liner design this near cutoff mode has a theoretical maximum attenuation of nearly 200 dB per L/D. The data show even higher attenuations at the design condition than predicted by the theory for dissipation of a single mode within the liner. This additional attenuation is large for high open area ratios and should be accounted for in the theory. The data show the additional attenuation to be inversely proportional to acoustic resistance. It was thought that the additional attenuation could be caused by reflection and modal scattering at the hard to soft wall interface. A reflection model was developed, and then modified to fit the data. This model was checked against independent (multiple pure tone) data with good agreement.

Heidelberg, L. J.↗
NASA NTRS1981

Three-dimensional turbulent boundary layer development and separation in V/STOL engine inlets at incidence with small-cross flow and curvature influences

The study concerns the influence of the three-dimensional cross flows on the compressible turbulent boundary layer development and flow separation prediction around V/STOL engine inlets at high incidence. The governing equations for the three-dimensional boundary layer flow with small-cross approximation are solved numerically on an intrinsic streamline coordinate system. Results are presented to illustrate the effects of small cross-flow, compressibility and streamline curvatures on the flow. Comparisons of the results with the wind tunnel data for scaled model and with data obtained from another existing compressible axisymmetric turbulent boundary layer scheme are included in the analysis.

Chou, D. C.↗
NASA NTRS1981

Applications of Landsat imagery to a coastal inlet stability study

Polcyn and Lyzenga (1975) and Middleton and Barber (1976) have demonstrated that it is possible to correlate the radiance values of a multispectral imagery, such as Landsat imagery, with the depth related information. The present study is one more example of such an effort. Two sets of Landsat magnetic tape were obtained and displayed on the screen of an Image-100 computer. Spectral analysis was performed to produce various signatures, their extent, and location. Subsequent ground truth observations and measurements were gathered by means of hydrographic surveys and low altitude aerial photographs for interpretation and calibration of the Landsat data. Finally, a coastal engineering assessment based on the Landsat data was made. Recommendations regarding the navigational canal alignment and dredging practice are presented in the light of inlet stability.

Wang, Y.-H.↗
NASA NTRS1982

Computation of transonic potential flow about 3 dimensional inlets, ducts, and bodies

An analysis was developed and a computer code, P465 Version A, written for the prediction of transonic potential flow about three dimensional objects including inlet, duct, and body geometries. Finite differences and line relaxation are used to solve the complete potential flow equation. The coordinate system used for the calculations is independent of body geometry. Cylindrical coordinates are used for the computer code. The analysis is programmed in extended FORTRAN 4 for the CYBER 203 vector computer. The programming of the analysis is oriented toward taking advantage of the vector processing capabilities of this computer. Comparisons of computed results with experimental measurements are presented to verify the analysis. Descriptions of program input and output formats are also presented.

Reyhner, T. A.↗