Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Capturing the Impact of Fuel Octane Number on Modern Gasoline Vehicles with Octane Indices

The need for high efficiency automotive engines has led to more complex air handling and fuel injection systems, higher compression ratios, more advanced combustion and aftertreatment systems, and the use of fuels with higher octane ratings. Higher octane number fuels have a lower propensity to knock. This work studies the influence of changing fuel octane rating on two modern production gasoline vehicles, one with a naturally aspirated, port injected engine and the other with a turbocharged, direct injected engine, using fuels with four different octane number grades (with 85, 87, 91, and 93 anti-knock indices) and operated over a variety of driving cycles and temperature conditions. Unlike previous studies, this effort develops and demonstrates a methodology that isolates fuel effects on fuel consumption and provides a clear view of the octane impact on existing vehicles. While fuel octane rating can also impact factors such as the allowable compression ratio and gear shifting strategies, this study examines fuel consumption changes that are solely attributable to octane rating on production vehicles. The developed approach uses results from drive cycle as well as steady-state tests along with response surface modeling to predict the engine combustion phasing and changes in efficiency for each fuel relative to the baseline 87 anti-knock index (AKI) fuel. The methodology is then used to capture the role of fuel octane rating on powertrain efficiency over Environmental Protection Agency (EPA) certification drive cycles and demonstrate the variation of that impact as a function of powertrain output power. Based on the vehicles and fuels tested in this study, the metrics indicate that the effects of octane on efficiency are limited to a portion of the operating modes represented in the driving cycles used for vehicle certification. In addition, an octane potential benefit index (OPBI) suggests that the vehicle with the turbocharged, direct injected engine has a greater potential to benefit from higher octane number fuel compared to the naturally aspirated, port injected engine and proposes a way to quantify this impact for production vehicles.

Jehlik, Forrest↗
DOE OSTI2021

Experimental Fuel Consumption Results from a Heterogeneous Four-Truck Platoon

Platooning has the potential to reduce greenhouse gas missions of heavy-duty vehicles. Prior platooning studies have chiefly focused on the fuel economy characteristics and three-truck platoons, and most have investigated aerodynamically homogeneous platoons with trucks of the same trim. For real world application and accurate return on investment for potential adopters, non-uniform platoons and the impacts of grade and disturbances on a platoon’s fuel economy must also be characterized. This study investigates the fuel economy of a heterogeneous four-truck platoon on a closed test track. Tests were run for one hour at a speed of 45 mph. The trucks used for this study are two 2015 Peterbilt 579’s with a Cummins ISX15 and a Paccar MX-13, and two 2009 Freightliner M915A5’s, one armored and the other unarmored. Many analysis methodologies were leveraged to describe and compare the fuel data, including lap-wise and track-segment analysis. The methodology for dividing the data into laps is described in detail. The influence of other factors beyond the aerodynamics of platooning is discussed. CAN fuel rate analysis showed excellent agreement with previous experimental trends for two and three-truck platoons. In general, the indicated fuel economy benefits in this study were 5-11% for following vehicles and 0-4% for the lead vehicle in platoon relative to their baseline fuel consumption. On a cumulative basis, all platoons saved fuel, ranging from 6% to 8% versus the sum of the standalone trucks’ fuel consumption. The practical implications of the fuel economy results are discussed, as well as avenues for future research. Introduction and Motivation platooning is controlled coordination of two or more vehicles in a convoy, sometimes called CACC (Coordinated or Cooperative Adaptive Cruise Control). The distance between vehicles in a platoon can be controlled tightly at no additional fatigue to the driver. Platooning vehicles can also respond quickly to braking events of the leader, much more quickly than the typical human driver’s reaction time of 1-1.5 s. Therefore, vehicles in a platoon can follow each other much more closely than would usually be considered a safe following distance under human operation. It is implied that under very close following conditions, platooning technology must be extremely robust before it is safe for wide-scale implementation. Platooning is under investigation as a fuel-saving technology. Close-following significantly reduces aerodynamic drag for both leading and trailing vehicles. According to the NRC in 2010, aerodynamic drag represents roughly half of a Class-8 truck’s on-highway fuel usage, meaning a 20% reduction in drag roughly equals a 10% reduction in fuel usage, if all other sources of energy loss remain equal (i.e. accessory, rolling resistance, drivetrain, braking). It is by aerodynamics that platooning saves fuel. At risk of oversimplifying the aerodynamics, following (or trailing) vehicles experience reduced wind velocity due to shielding, and the leading vehicles experience an increased aft pressure, especially at distances closer than 75’ (23 m).

greenhouse gas emissions, truck platoon, heavy-dut↗
NASA NTRS2013

Alternate-Fueled Combustor-Sector Emissions

In order to meet rapidly growing demand for fuel, as well as address environmental concerns, the aviation industry has been testing alternate fuels for performance and technical usability in commercial and military aircraft. In order to make alternate fuels (and blends) a viable option for aviation, the fuel must be able to perform at a similar or higher level than traditional petroleum fuel. They also attempt to curb harmful emissions, and therefore a truly effective alternate fuel would emit at or under the level of currently used fuel. This report analyzes data from gaseous and particulate emissions of an aircraft combustor sector. The data were evaluated at various inlet conditions, including variation in pressure and temperature, fuel-to-air ratios, and percent composition of alternate fuel. Traditional JP-8+100 data were taken as a baseline, and blends of JP-8+100 with synthetic-paraffinic-kerosene (SPK) fuel (Fischer-Tropsch (FT)) were used for comparison. Gaseous and particulate emissions, as well as flame luminosity, were assessed for differences between FT composition of 0, 50, and 100 percent. The data show that SPK fuel (an FT-derived fuel) had slightly lower harmful gaseous emissions, and smoke number information corroborated the hypothesis that SPK-FT fuels are cleaner burning fuels.

Saxena, Nikita T.↗
NASA NTRS2014

Hot Hydrogen Testing of Tungsten-Uranium Dioxide (W-UO2) CERMET Fuel Materials for Nuclear Thermal Propulsion

CERMET fuel materials are being developed at the NASA Marshall Space Flight Center for a Nuclear Cryogenic Propulsion Stage. Recent work has resulted in the development and demonstration of a Compact Fuel Element Environmental Test (CFEET) System that is capable of subjecting depleted uranium fuel material samples to hot hydrogen. A critical obstacle to the development of an NCPS engine is the high-cost and safety concerns associated with developmental testing in nuclear environments. The purpose of this testing capability is to enable low-cost screening of candidate materials, fabrication processes, and further validation of concepts. The CERMET samples consist of depleted uranium dioxide (UO2) fuel particles in a tungsten metal matrix, which has been demonstrated on previous programs to provide improved performance and retention of fission products1. Numerous past programs have utilized hot hydrogen furnace testing to develop and evaluate fuel materials. The testing provides a reasonable simulation of temperature and thermal stress effects in a flowing hydrogen environment. Though no information is gained about radiation damage, the furnace testing is extremely valuable for development and verification of fuel element materials and processes. The current work includes testing of subscale W-UO2 slugs to evaluate fuel loss and stability. The materials are then fabricated into samples with seven cooling channels to test a more representative section of a fuel element. Several iterations of testing are being performed to evaluate fuel mass loss impacts from density, microstructure, fuel particle size and shape, chemistry, claddings, particle coatings, and stabilizers. The fuel materials and forms being evaluated on this effort have all been demonstrated to control fuel migration and loss. The objective is to verify performance improvements of the various materials and process options prior to expensive full scale fabrication and testing. Post test analysis will include weight percent fuel loss, microscopy, dimensional tolerance, and fuel stability.

Hickman, Robert↗
DOE OSTI2015

Fuel nozzle assembly for use as structural support for a duct structure in a combustor of a gas turbine engine

A fuel nozzle assembly for use in a combustor apparatus of a gas turbine engine. An outer housing of the fuel nozzle assembly includes an inner volume and provides a direct structural connection between a duct structure and a fuel manifold. The duct structure defines a flow passage for combustion gases flowing within the combustor apparatus. The fuel manifold defines a fuel supply channel therein in fluid communication with a source of fuel. A fuel injector of the fuel nozzle assembly is provided in the inner volume of the outer housing and defines a fuel passage therein. The fuel passage is in fluid communication with the fuel supply channel of the fuel manifold for distributing the fuel from the fuel supply channel into the flow passage of the duct structure.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Ultra-compact system for characterization of physical, chemical and ignition properties of fuels

The present disclosure relates to a miniaturized fuel laboratory system that makes use of a housing, a processor housed within the housing, and a fuel inlet port supported from the housing for receiving a quantity of fuel to be used as a fuel test sample. The system may also have at least one fuel sensor housed in the housing in communication with the fuel inlet port for receiving the fuel test sample and carrying out combustion thereof. An electronic component may be housed in the housing, which enables communication with an external remote subsystem. A database may be incorporated which contains at least one of stored fuel characteristics or stored fuel analysis models, accessible by the processor. The processor may use fuel oxidation information generated by the fuel sensor, and at least one of the stored fuel characteristics or stored combustion models, to determine at least one fuel characteristic of the fuel test sample.

McNenly, Matthew J.↗
DOE OSTI2022

Fuel injection module for segmented annular combustion system

The present disclosure is directed to a fuel injection module for a segmented annular combustion system. The fuel injection module includes a housing body, a fuel nozzle portion, and at least one fuel injection lance. The fuel nozzle portion is fluidly coupled to a fuel nozzle plenum within the housing body, and the at least one fuel injection lance is fluidly coupled to an injector fuel plenum within the housing body. In some cases, the fuel nozzle portion is a bundled tube fuel nozzle having one or more subsets of tubes. The fuel injection lances are positioned along a radial side of the housing body or circumferentially between two subsets of tubes. Liquid fuel cartridges extend through the fuel nozzle portion, the fuel injection lances, or both.

42 ENGINEERING↗
DOE OSTI2018

The effect of variable fuel staging transients on self-excited instabilities in a multiple-nozzle combustor

Combustion instability in gas turbine engines is often mitigated using fuel staging. Fuel staging, sometimes referred to as fuel splitting, is a strategy by which fuel is unevenly distributed between different nozzles of a multiple-nozzle combustor. These fuel splits are conducted in a transient manner in real engines, and the effects of these transients on instability are not well characterized. This work fills this gap by systematically studying the effects of transient fuel staging on self-excited combustion instability by varying the amount of staging fuel (staging amplitude), timescale in which the fuel is added (transient duration), and whether staging fuel is added or subtracted (transient direction). In this work, three staging amplitudes, five transient durations, and both transient directions are considered. The transient timescales are broadly divided into “short” duration transients, which have fuel delivery timescales shorter than the characteristic instability decay or onset timescales, and “long” duration transients, which have fuel delivery timescales longer than the characteristic instability decay or onset timescales. For short duration transients, we find the instability decay timescale depends on staging amplitude but does not depend on transient duration. For long duration transients, we find the instability decay timescale does not strongly depend on staging amplitude. The instability onset timescale is found to be longer and more variable between runs than the instability decay timescale for a given fuel delivery timescale. The onset timescale is also longer in duration and more variable than the decay timescale at a given fuel delivery timescale, implying that the instability rise process is overall more variable and slower than the instability decay process. Analysis of combustor damping rates show a strong dependence of damping rate on staging amplitude but no strong dependence on transient duration or direction. Instantaneous phase difference images between p' and are used to differentiate regions in the combustor that have constructive versus destructive interference between heat release rate oscillations and pressure fluctuations. Furthermore, the phase images show that p' and q . ' become in-phase early in the transient for the onset transients.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2026

Modeling and analysis of synthetic liquid fuel production from CO 2 and nuclear energy using methanol-to-diesel process

Electrofuels (e-fuels) are synthetic fuels produced from carbon dioxide (CO 2 ) and electricity for blending with or replacing petroleum fuels. Nuclear energy is an attractive energy feedstock for e-fuel production because of its low environmental footprint and its ability to provide steady heat and power essential for e-fuels production. We modeled and evaluated the cost and environmental footprint of e-fuels production in the distillate range for three nuclear power scales, 100, 500, and 1000 MWe, through methanol and olefins intermediates leveraging commercial or high technology readiness level (TRL) processes. Compared to the commonly studied e-fuels from Fischer Tropsch process that has a distillate yield of <70% with the rest being low value naphtha, the proposed process via methanol intermediate increases the product selectivity with distillate yield of 96% and only 4% naphtha. The modeled process has a carbon conversion ratio of 98%, and a process energy efficiency of 56% relative to the total equivalent nuclear electricity input. The e-fuel plant economics and GHG emissions were estimated by considering CO 2 collected from ethanol plants adjacent to nuclear power plants. The estimated minimum fuel selling prices (MFSP) of e-fuel is in the range of $5.7-$9.1/gal depending on e-fuel plant scale, electricity cost, and CO 2 transportation distance. The corresponding e-fuels life cycle GHG emissions is estimated in the range of 5-6 gCO 2 e/MJ of liquid fuel using the R&D Greenhouse gases, Regulated Emissions, and Energy use in Technologies (R&D GREET) model.

10 SYNTHETIC FUELS↗
DOE OSTI2015

Fabrication, Welding, and Inspection Techniques in Preparation for In-Reactor Testing of Accident Tolerant Fuels

After the Fukushima events in 2011, DOE-NE in collaboration with nuclear industry shifted R&D emphasis to accident performance of LWR fuels under extended loss of active cooling and steam exposure. DOE-NE has created a roadmap for the “Development of Light Water Reactor Fuels with Enhanced Accident Tolerance.” The mission of the Accident Tolerant Fuel (ATF) Roadmap is to develop the next generation of LWR fuels with improved performance, reliability, and safety characteristics during normal operations and accident conditions and with reduced waste generation. The ultimate goal of the ATF roadmap is to support the insertion of lead fuel rods (LFRs) or lead fuel assemblies (LFAs) of an Accident Tolerant Fuel into a commercial LWR within 10 years (i.e., by the end of FY-2022). As a step toward this goal, an irradiation test series has been developed to assess the performance of proposed ATF concepts under normal LWR operating conditions. Data generated by this test program will be used to establish the feasibility of certain aspects of proposed ATF concepts, as well as provide information to support screening among concepts; as such, it is an integral part of Phase I: Feasibility Assessment and Down-Selection outlined in the ATF Roadmap. This irradiation test series is planned to be performed as a series of drop-in capsule tests to be irradiated in the Advanced Test Reactor (ATR) operated by the Idaho National Laboratory (INL), and it has been designated as the ATF-1 test series. Current fission reactors use zirconium-based fuel cladding because of its extremely low macroscopic thermal neutron absorption cross-section, good high temperature strength, and decent corrosion resistance. However, advanced, innovative materials may provide these same benefits while increasing reactor safety margin, core power density, and fuel utilization. These advanced fuel cladding systems will allow revolutionary cladding performance and enhanced fuel mechanical designs, however, challenges exist in design, analysis and fabrication of innovative, never before tested, fuel cladding systems for in-reactor testing. This paper highlights the challenges associated with design, fabrication and welding, and inspection of innovative materials and actions taken to address those challenges in preparation for the Phase I ATR irradiation testing. The lessons learned from Phase I of this experiment can be used to guide researchers for design and analysis of future in-reactor testing of advanced fuel cladding systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Potential Research and Development Opportunities for Light Water Reactor Spent Nuclear Fuel at INL

This report documents the commercial spent nuclear fuel currently in storage at Idaho National Laboratory with a specific focus on the potential research and development (R&D) opportunities for this material. Commercial spent nuclear fuel is stored in dry casks on the INL site at the Idaho Nuclear Technology and Engineering Center (INTEC, formerly the Idaho Chemical Processing Plant or ICPP). This spent fuel was part of the DOE-industry cooperative dry cask demonstration project that began in 1983 and from historical fuel testing and treatment activities that had been performed at the Test Area North (TAN)-607 facility. Most of the fuel is “low burnup,” but given that it was removed from the respective reactors between 1970 and 1985, it was representative for its time. The majority of the fuel is of the 15×15 Westinghouse PWR variety, though additional fuel types (e.g., TN-BRP) and configurations are also stored. Potential R&D opportunities identified are (1) the REA-2023 cask, (2) the TN-BRP cask, and (3) the Castor V/21 cask. Fuel from the TN-24P may be an alternative to the intact assemblies in the Castor V/21. Specifically, the REA-2023 cask contains 9 rods that have been exposed to air since 2005. These rods have a detailed pre-loading characterization and thus any changes in corrosion or geometry can most likely be attributed to the storage environment. In addition, similar rods to the nine in REA-2023 reside in the Castor V/21 cask whose environment has been maintained with inert nitrogen. The Castor V/21 cask also contains intact PWR assemblies that could be used to perform limited confirmation of the pyroprocessing approach. An alternative to the use of the Castor assemblies for pyroprocessing is the consolidated fuel that is stored in the TN-24P, which would not require removal from the assembly grid since it has already been packaged in accessible two-piece shell strongback containers. The TN-BRP cask contains a number of Gd-doped, low burnup assemblies that could be of use to validate code packages used to justify burnup-up credit for boiling water reactors (BWRs). The INL dry casks are stored on the CPP-2707 pad at INTEC, adjacent to the CPP-603 Irradiated Fuel Storage Facility, which incorporates a dry hot cell that has the potential to receive a full scale commercial cask of the types identified. Several evaluations have been made regarding this task, including full scale mockup testing of the physical clearances required to remove and handle fuel assemblies and components. A proposed schedule of 14 months and cost of $5.3 million was the outcome of analysis performed by Fluor Idaho and is included as Appendix A & B. In addition to the spent fuel at INL, there is also a full-scale mockup assembly that was fabricated for the Protypical Consolidation Demonstration Project to validate fuel rod consolidation approaches. The assembly was fabricated by Westinghouse as a 15 x 15 PWR, using Zircaloy-4 tubing and steel end fittings in accordance with product specifications. The only departure from specification is the use of copper metal in lieu of uranium oxide pellets to achieve a weight that is within 10% of the standard.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Integration of the Back End of the Nuclear Fuel Cycle

Management of spent nuclear fuel and high-level radioactive waste consists of three main phases – storage, transportation, and disposal – commonly referred to as the back end of the nuclear fuel cycle. Current practice for commercial spent nuclear fuel management in the United States (US) includes temporary storage of spent fuel in both pools and dry storage systems at operating or shutdown nuclear power plants. Storage pools are filling to their operational capacity, and management of the approximately 2,200 metric tons of spent fuel newly discharged each year requires transferring older and cooler spent fuel from pools into dry storage. Unless a repository becomes available that can accept spent fuel for permanent disposal, projections indicate that the US will have approximately 136,000 metric tons of spent fuel in dry storage systems by mid-century, when the last plants in the current reactor fleet are decommissioned. Current designs for dry storage systems rely on large multi-assembly canisters, the most common of which are so-called “dual-purpose canisters” (DPCs). DPCs are certified for both storage and transportation, but are not designed or licensed for permanent disposal. The large capacity (greater number of spent fuel assemblies) of these canisters can lead to higher canister temperatures, which can delay transportation and/or complicate disposal. This current management practice, in which the utilities continue loading an ever-increasing inventory of larger DPCs, does not emphasize integration among storage, transportation, and disposal. This lack of integration does not cause safety issues, but it does lead to a suboptimal system that increases costs, complicates storage and transportation operations, and limits options for permanent disposal. This paper describes strategies for improving integration of management practices in the US across the entire back end of the nuclear fuel cycle. The complex interactions between storage, transportation, and disposal make a single optimal solution unlikely. However, efforts to integrate various phases of nuclear waste management can have the greatest impact if they begin promptly and continue to evolve throughout the remaining life of the current fuel cycle. A key factor that influences the path forward for integration of nuclear waste management practices is the identification of the timing and location for a repository. The most cost-effective path forward would be to open a repository by mid-century with the capability to directly dispose of DPCs without repackaging the spent fuel into disposalready canisters. Options that involve repackaging of spent fuel from DPCs into disposalready canisters or that delay the repository opening significantly beyond mid-century could add 10s of billions of dollars to the total system life cycle cost.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Developing the Irradiation Plan for U-10Mo LEU Fuel Qualification for the Advanced Test Reactor

The Department of Energy (DOE), National Nuclear Security Administration’s Office of Material Management and Minimization (M3) mission is to convert, remove, and dispose of vulnerable nuclear material located at civilian sites worldwide. As part of its mission, M3’s Office of Convert works around the world to convert research reactors and isotope production facilities to non-weapon-usable nuclear material, both domestically and abroad. In support of this, the Office of Convert is working with the Idaho National Laboratory (INL) to develop and qualify new fuels and technologies to support conversion efforts domestically and abroad. The INL also supports the Office of Convert by working on converting the Advanced Test Reactor (ATR) and the Advanced Test Reactor Critical (ATRC) from using High Enriched Uranium (HEU) fuel to Low Enriched Uranium (LEU) fuel. To ensure the viability of ATR LEU fuel, the fuel system should meet a similar functional and operational envelope as the current HEU fuel. A series of irradiation tests of the U-10Mo LEU fuel system is required to support the qualification of the fuel system for use in the ATR and several other U.S. High-Performance Research Reactors (USHPRRs). These irradiation tests include: • Mini-Plate tests (MP-1, MP-2, and MP-ATR), • Full-Size Plate tests (FSP-1, and FSP-ATR), and • Element Tests (ET-1, ET-2, and ET-3). The MP tests will use multiple small-scale samples that will provide sufficient data across a wide variety of irradiation conditions to qualify the fuel. The FSP tests will use a small number of full-sized fuel plates to confirm the MP test results are representative of the prototypic plate geometry performance. The MP and FSP irradiation tests occur in ATR test locations. The ETs will use full-sized fuel elements located in ATR core driver positions to explore the full operating ranges of the ATR and other USHPRRs and to confirm that the MP and FSP test results are representative of the prototypic element geometry performance. The established testing functional and operational requirements of MP-1, MP-2, FSP-1, and ET 1 achieve the base fuel qualification needs of the USHPRRs, while the high-level purposes of MP-ATR, FSP ATR, ET 2, and ET-3 are focused on demonstrating U-10Mo fuel for ATR use.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Generation IV Benchmarking of TRISO Fuel Performance Models Under Accident Conditions Final Report

The Generation IV International Forum (GIF) is a co-operative international endeavor of fourteen members organized to carry out the research and development needed to establish the feasibility and performance capabilities of the next generation nuclear energy systems. GIF selected six reactor technologies, amongst which is the Very High Temperature Reactor (VHTR) that is primarily dedicated to the cogeneration of electricity and hydrogen. The technical basis for VHTR is the tristructural isotropic (TRISO)-coated particle fuel, the graphite as the core structure, helium coolant, as well as the dedicated core layout and lower power density to removal decay heat in a natural way. At the heart of safety features of the VHTR concept lie the TRISO fuel particles that are designed to keep their structural integrity and retain fission products at temperatures up to 1600°C. As part as the design and future operation of VHTRs, a key aspect is the accurate prediction of fuel performance under irradiation and accident conditions. Modeling and simulation allow prediction of TRISO fuel behavior when subject to neutron flux and in high temperature accident scenarios. The refinement of the fuel performance models and codes is performed by comparison to in-pile and out-of-pile experimental data that reproduce the expected irradiation conditions in high temperature gas-cooled reactors (HTGRs). Historically, the International Atomic Energy Agency (IAEA) developed a benchmark dedicated to the validation of predictive methods for fuel and fission product behavior through the Coordinated Research Program CRP-2 (IAEA, 1997). CRP-2 was later updated to cover fuel fabrication, quality assurance, irradiation performance, safety testing, and spent fuel. The scope of the resulting CRP-6 benchmarks focused on HTGR fuel performance and fission product release (IAEA, 2012). Taking advantage of additional TRISO fuel fabrication, irradiation, and safety testing campaigns, GIF launched a Generation IV Benchmarking of TRISO Fuel Performance Models under Accident Conditions in late 2015. This GIF benchmark is a three-year program steered by Idaho National Laboratory (INL, USA). The other participants include the Japan Atomic Energy Agency (JAEA, Japan) and the Korea Atomic Energy Research Institute (KAERI, Korea). The objectives of the benchmark are to: follow on the IAEA CRP benchmarks, (2) model fission product release under accident conditions, (3) compare results obtained by the fuel performance modeling codes of the benchmark participants, and (4) compare these code predictions to experimental data. Safety tests chosen for modeling include the first and second experiments of the Advanced Gas Reactor program (AGR-1 and AGR-2) and the High Flux Reactor (HFR) EU1bis experiment. This report presents the results obtained by the three research institutions using their respective fuel performance modeling codes. Comparisons of the corresponding fission product release predictions are made with experimental data from AGR-1, AGR-2, and HFR-EU1bis. The benchmark results show good agreements between all participants but also show a general trend of over-prediction of the experimental release data, which is mainly attributed to the use of over-estimated diffusion coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2013

Dealing with Historical Discrepancies: The Recovery of National Research Experiment (NRX) Reactor Fuel Rods at Chalk River Laboratories (CRL) - 13324

Following the 1952 National Research Experiment (NRX) Reactor accident, fuel rods which had short irradiation histories were 'temporarily' buried in wooden boxes at the 'disposal grounds' during the cleanup effort. The Nuclear Legacy Liabilities Program (NLLP), funded by Natural Resources Canada (NRCan), strategically retrieves legacy waste and restores lands affected by Atomic Energy of Canada Limited (AECL) early operations. Thus under this program the recovery of still buried NRX reactor fuel rods and their relocation to modern fuel storage was identified as a priority. A suspect inventory of NRX fuels was compiled from historical records and various research activities. Site characterization in 2005 verified the physical location of the fuel rods and determined the wooden boxes they were buried in had degraded such that the fuel rods were in direct contact with the soil. The fuel rods were recovered and transferred to a modern fuel storage facility in 2007. Recovered identification tags and measured radiation fields were used to identify the inventory of these fuels. During the retrieval activity, a discrepancy was discovered between the anticipated number of fuel rods and the number found during the retrieval. A total of 32 fuel rods and cans of cut end pieces were recovered from the specified site, which was greater than the anticipated 19 fuel rods and cans. This discovery delayed the completion of the project, increased the associated costs, and required more than anticipated storage space in the modern fuel storage facility. A number of lessons learned were identified following completion of this project, the most significant of which was the potential for discrepancies within the historical records. Historical discrepancies are more likely to be resolved by comprehensive historical record searches and site characterizations. It was also recommended that a complete review of the wastes generated, and the total affected lands as a result of this historic 1952 NRX accident be undertaken. These lessons and recommendations have lead to changes in how the NLLP is executed in the CRL waste management areas. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2013

Performance evaluation of two-stage fuel cycle from SFR to PWR

One potential fuel cycle option being considered is a two-stage fuel cycle system involving the continuous recycle of transuranics in a fast reactor and the use of bred plutonium in a thermal reactor. The first stage is a Sodium-cooled Fast Reactor (SFR) fuel cycle with metallic U-TRU-Zr fuel. The SFRs need to have a breeding ratio greater than 1.0 in order to produce fissile material for use in the second stage. The second stage is a PWR fuel cycle with uranium and plutonium mixed oxide fuel based on the design and performance of the current state-of-the-art commercial PWRs with an average discharge burnup of 50 MWd/kgHM. This paper evaluates the possibility of this fuel cycle option and discusses its fuel cycle performance characteristics. The study focuses on an equilibrium stage of the fuel cycle. Results indicate that, in order to avoid a positive coolant void reactivity feedback in the stage-2 PWR, the reactor requires high quality of plutonium from the first stage and minor actinides in the discharge fuel of the PWR needs to be separated and sent back to the stage-1 SFR. The electricity-sharing ratio between the 2 stages is 87.0% (SFR) to 13.0% (PWR) for a TRU inventory ratio (the mass of TRU in the discharge fuel divided by the mass of TRU in the fresh fuel) of 1.06. A sensitivity study indicated that by increasing the TRU inventory ratio to 1.13, The electricity generation fraction of stage-2 PWR is increased to 28.9%. The two-stage fuel cycle system considered in this study was found to provide a high uranium utilization (>80%). (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2017

Swedish Solution for Reconditioning, Transport, Interim Storage and Final Disposal of Failed Fuel - 17024

Despite today's increasingly more reliable operation of nuclear power plants, failed fuel rods exist in all Swedish plants. Managing intermediate storage and sub-sequential final disposal of such rods has been a growing problem. The Swedish system for spent fuel management uses the principle of intermediate storage of the fuel in a central intermediate storage facility (CLAB) before disposal in a final repository according to the KBS-3 method. However, the intermediate storage facility does not allow storage of failed fuel and the final repository has limitations on moisture in the deposited fuel and hence failed or broken fuel rods cannot be accepted as-is. The nuclear power companies in Sweden have jointly established the Swedish Nuclear Fuel and Waste Management Co, SKB, to manage the spent fuel and the operational waste. To find a solution to transport the failed fuel to storage, SKB has established a project with the goal to have all currently failed fuel rods from all the Swedish nuclear power plants reconditioned and transported to the intermediate storage facility before the year of 2020. The project has established the acceptance criteria for reconditioned failed fuel in the final repository and evaluated a number of options for treatment, encapsulation and transportation of the failed fuel rods. Furthermore, two suppliers have developed reconditioning methods fulfilling the criteria and contracts were signed with both suppliers in May 2016. This paper outlines the details of the Swedish solution for treatment and storage of failed fuel including the technical requirements for the reconditioning method and transportability. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Meeting sustainable aviation fuel policy targets through first generation corn biorefineries

This paper investigates options to produce low carbon and renewable aviation fuel through existing commercial first generation biorefineries, which could be strategic given the rapid growth of the electric vehicle market for personal mobility. We evaluate the environmental impact of retrofitting a first generation biorefinery to produce aviation fuel through chemical process simulation. The analysis investigates the potential for reducing greenhouse gas (GHG) emissions and displacing fossil fuel (petroleum-based jet kerosene) in the aviation fuel industry through using corn feedstocks in dry grind biorefineries to convert sugars to 1,4-dimethylcyclooctane (DMCO), which qualifies as renewable jet-A fuel blend and is infrastructure compatible. Further, the average life cycle GHG emissions for a baseline case and a scenario with carbon capture and storage (CCS) of fermentative CO 2 are 36 and 5g CO 2 e/MJ DMCO, respectively. Investment in CCS at the biorefinery and adoption of crop best management practices on farms are essential for mitigating the risks of induced land use change GHG emissions for existing corn biorefineries. DMCO as a low-carbon aviation fuel could be a strategic fuel product for retrofitting existing corn dry grind facilities. For aviation fuel supply, corn dry grind facilities could displace about 12% of jet fuel demand in the near term, which would meet sustainable aviation fuel policy targets. We conclude that corn-to-DMCO shows promise for near-term low-carbon fuel markets in the aviation industry and as a bridge to developing biomass-based jet fuel in the future.

09 BIOMASS FUELS↗