Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FRACTURE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Fracture analysis of various cracked configurations in sheet and plate materials

A two-parameter fracture criterion was derived which relates the linear-elastic stress-intensity factor at failure, the elastic nominal failure stress, and two material parameters. The fracture criterion was used previously to analyze fracture data for surface- and through-cracked sheet and plate specimens under tensile loading. The fracture criterion was applied to center-crack tension, compact, and notch-band fracture specimens made of steel, titanium, or aluminum alloy materials tested at room temperature. The fracture data included a wide range of crack lengths, specimen widths, and thicknesses. The materials analyzed had a wide range of tensile properties. Failure stresses calculated using the criterion agreed well (plus or minus 10 percent) with experimental failure stresses. The criterion was also found to correlate fracture data from different specimen types (such as center-crack tension and compact specimens), within plus or minus 10 percent for the same material, thickness, and test temperature.

Newman, J. C., Jr.↗

Fracture analysis of various cracked configurations in sheet and plate materials

A two-parameter fracture criterion has been derived which relates the linear-elastic stress-intensity factor at failure, the elastic nominal failure stress, and two material parameters. The fracture criterion was applied to center-crack tension, compact, and notch-bend fracture specimens made of steel, titanium, or aluminum alloy materials tested at room temperature. The fracture data included a wide range of crack lengths, specimen widths, and thicknesses. The materials analyzed had a wide range of tensile properties. Failure stresses calculated using the criterion agreed well (plus or minus 10 percent) with experimental failure stresses. The criterion was also found to correlate fracture data from different specimen types (such as center-crack tension and compact specimens), within plus or minus 10 percent for the same material, thickness, and test temperature.

Newman, J. C., Jr.↗

Thermally induced damage in composite space structure: Predictive methodology and experimental correlation

A general analysis method is presented to predict matrix cracks in all plies of a composite laminate, and resulting degraded laminate properties, as functions of temperature or thermal cycles. A shear lag solution of the stresses in the vicinity of cracks and a fracture mechanics crack formation criteria are used to predict cracks. Damage is modeled incrementally, which allows the inclusion of the effects of temperature dependent material properties and softening of the laminate due to previous cracking. The analysis is incorporated into an easy-to-use computer program. The analysis is correlated with experimentally measured crack densities in a variety of laminates exposed to monotonically decreasing temperatures. Crack densities are measured at the edges of specimens by microscopic inspection, and throughout the specimen volumes by x-ray and sanding down of the edges. Correlation between the analytical results and the crack densities in the interiors of the specimens was quite good. Crack densities measured at specimen edges did not agree with internal crack densities (or analyses) in some cases. A free-edge stress analysis clarified the reasons for these discrepancies.

Park, Cecelia↗

3D Gel-Printing of TiC-Reinforced 316L Stainless Steel: Influence of the Printing Parameters

In this paper, the composite composed of TiC (35 wt.%) reinforced 316L stainless steel matrix was successfully prepared using a 3D gel-printing (3DGP) process. The “step effect” of 3D printing can be reduced using reasonable parameter settings. The properties of TiC/316L slurry for 3DGP and the influence of the different printing parameters on the surface quality of the samples, such as the extrusion overlaps and printing speed, were researched. The microstructure and fracture morphology of the sintered sample were revealed using scanning electron microscopy. The surface roughness, density, and mechanical properties were also measured. When the internal diameter of the nozzle was 0.50 mm, the result showed that the proper extrusion overlap parameter was 0.08 mm and the maximum printing speed was 20 mm/s. Furthermore, the minimum surface roughness value was 10 μm. After sintering, the mechanical performances were similar to those obtained using a conventional powder metallurgy process.

36 MATERIALS SCIENCE↗

Development of Laser Powder Bed Fusion NASA HR-2 for Hydrogen Sensitive Liquid Rocket Engine Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000s. AM has provided new design and manufacturing opportunities to reduce cost and schedule, consolidate parts, and optimize performance. Laser Powder Bed Fusion (L-PBF) is one of the most commonly used AM processes to fabricate components of complex shape requiring fine feature resolution. Due to exposure to high-pressure gaseous hydrogen, mechanical property degradation caused by hydrogen environment embrittlement (HEE) is a critical concern for many materials in liquid hydrogen propulsion systems. NASA has identified the need to develop and advance new materials in unique engine applications using liquid hydrogen as a propellant. One such material being developed at NASA Marshall Space Flight Center is L-PBF NASA HR-2 (Hydrogen Resistant-2), a high-strength Fe-Ni-based superalloy resistant to HEE. The chemistry of NASA HR-2 was formulated to meet requirements for key liquid rocket engine (LRE) components that operate in high-pressure hydrogen environments. Initial development and material characterization found that NASA HR-2 has excellent L-PBF printability, and its microstructure evolves well after heat treatment. This new alloy has undergone fundamental metallurgical evaluations, heat treatment studies, detailed microstructure characterization, and mechanical testing across a range of temperatures. Tensile testing was performed in a pressurized gaseous hydrogen (GH2) environment to assess its resistance to HEE. L-PBF NASA HR-2 has an average yield stress of 95 ksi, an ultimate tensile stress of 165 ksi, and a very high fracture elongation of 34 - 36% when tested in a high-pressure (5 ksi) hydrogen environment. The tensile property data confirms hydrogen has little influence on HR-2’s ductility, strength, and fracture behavior. L-PBF NASA HR-2 is a promising option for many hydrogen-sensitive LRE components that require exceptional resistance to HEE. This paper will provide an overview of the L-PBF process development, material characterization, mechanical and thermophysical properties, and LRE hardware development for NASA HR-2.

Po S Chen↗

Investigation on Microstructure and Mechanical Properties of TA10–Q245R Composite Plate Formed by Explosive Welding

The titanium alloy TA10 and the carbon steel Q245R are welded by explosive welding, and post-weld heat treatment (PWHT) is carried out for the TA10–Q245R composite plate. Microstructure and mechanical properties of the composite plate are investigated both in as-welded (AW) condition and after PWHT, respectively. Results show that, in AW condition, the bonding interface of composite plate presents wavy morphology, and at both sides of the interface plastic deformation is generated to a certain degree. Near the interface interdiffusion zone of alloying elements exists, and no Fe-Ti intermetallic compound is produced at the interface. SEM images indicate that the tensile fracture of composite plate presents the characteristic of ductile fracture, and no defects such as gas pores or impurities are found on the surface of shear fracture. After PWHT, the interfacial microstructure of the composite plate is obviously changed. Compared with the mechanical properties of the composite plate in AW condition, both tensile strength and shear strength of the composite plate are decreased to a certain extent after PWHT. With various factors into consideration, the suitable heat treatment procedure of TA10–Q245R composite plate is determined as follows: 550 °C × 1.5 h.

36 MATERIALS SCIENCE↗

Friction and fracture of single-crystal silicon carbide in contact with itself and titanium

An investigation was conducted to examine the friction properties and mechanical behavior of single-crystal silicon carbide (0001) surface sliding against itself and against polycrystalline titanium. The results indicate hexagon-shaped pits of silicon carbide and the formation of platelet hexagon-shaped wear debris of silicon carbide due to cleavages of both prismatic and basal planes as a result of silicon carbide sliding against itself. The fracturing of silicon carbide also occurs near the adhesive bond to titanium. The wear debris produced by brittle fracture plows the titanium and transfers to it. Further, the silicon carbide wear debris, which adhered and transferred to titanium, plows the silicon carbide surface and transfers back to it

Miyoshi, K.↗

Percutaneous CT and Fluoroscopy-Guided Screw Fixation of Pathological Fractures in the Shoulder Girdle: Technical Report of 3 Cases

ObjectiveTo review our initial experience with percutaneous CT and fluoroscopy-guided screw fixation of pathological shoulder-girdle fractures.Materials and MethodsBetween May 2014 and June 2015, three consecutive oncologic patients (mean age 65 years; range 57–75 years) with symptomatic pathological shoulder-girdle fractures unsuitable for surgery and radiotherapy underwent percutaneous image-guided screw fixation. Fractures occurred through metastases (n = 2) or a post-ablation cavity (n = 1). Mechanical properties of osteosynthesis were adjudged superior to stand-alone cementoplasty in each case. Cannulated screws were placed under combined CT and fluoroscopic guidance with complementary radiofrequency ablation or cementoplasty to optimise local palliation and secure screw fixation, respectively, in two cases. Follow-up was undertaken every few weeks until mortality or most recent appointment.ResultsFour pathological fractures were treated in three patients (2 acromion, 1 clavicular, 1 coracoid). Mean size of associated lesion was 2.6 cm (range 1–4.5 cm). Technical success was achieved in all cases (100 %), without complications. Good palliation and restoration of mobility were observed in two cases at 2–3 months; one case could not be followed due to early post-procedural oncologic mortality.ConclusionPercutaneous image-guided shoulder-girdle osteosynthesis appears technically feasible with good short-term efficacy in this complex patient subset. Further studies are warranted to confirm these promising initial results.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Mechanical Properties of a High Lead Glass Used in the Mars Organic Molecule Analyzer

The elastic constants, strength, fracture toughness, slow crack growth parameters, and mirror constant of a high lead glass supplied as tubes and funnels were measured using ASTM International (formerly ASTM, American Society for Testing and Materials) methods and modifications thereof. The material exhibits lower Young's modulus and slow crack growth exponent as compared to soda-lime silica glass. Highly modified glasses exhibit lower fracture toughness and slow crack growth exponent than high purity glasses such as fused silica.

lead↗

Low Velocity Sphere Impact of a Soda Lime Silicate Glass

This report summarizes TARDEC-sponsored work at Oak Ridge National Laboratory (ORNL) during the FY11 involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Starphire soda lime silicate glass. The intent was to better understand low velocity impact response in the Starphire for sphere densities that bracketed that of rock. Five sphere materials were used: borosilicate glass, soda-lime silicate glass, steel, silicon nitride, and alumina. A gas gun was fabricated to produce controlled velocity delivery of the spheres against Starphire tile targets. Minimum impact velocities to initiate fracture in the Starphire were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the any of the five sphere-Starphire-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Frictional effects contribute to fracture initiation. (2) Spheres with a lower elastic modulus require less force to initiate fracture in the Starphire than spheres with a higher elastic modulus. (3) Contact-induced fracture did not initiate in the Starphire SLS for impact kinetic energies < 150 mJ. Fracture sometimes initiated or kinetic energies between {approx} 150-1100 mJ; however, it tended to occur when lower elastic modulus spheres were impacting it. Contact-induced fracture would always occur for impact energies > 1100 mJ. (4) The force necessary to initiate contact-induced fracture is higher under dynamic or impact conditions than it is under quasi-static indentation conditions. (5) Among the five used sphere materials, silicon nitride was the closest match to 'rock' in terms of both density and (probably) elastic modulus.

36 MATERIALS SCIENCE↗

Effect of Ca and Sm Combined Addition on the Microstructure and Elevated-Temperature Mechanical Properties of Mg-6Al Alloys

In the present study, the microstructure and elevated-temperature mechanical properties of Mg-6Al, Mg-6Al-4Ca, Mg-6Al-4Sm and Mg-6Al-2Ca-2Sm alloys were investigated. The experimental results showed that the microstructure and elevated-temperature mechanical property of Mg-6Al alloy changed obviously with the different elements addition. By analyzing the results of optical microscope, x-ray diffraction analysis, scanning electron microscope, and transmission electron microscope, it could be determined that there was only Mg{sub 17}Al{sub 12} phase in Mg-6Al alloy, there were Al{sub 2}Ca and (Mg, Al){sub 2}Ca phases in Mg-6Al-4Ca alloy, there were Al{sub 2}Sm and Mg{sub 17}Al{sub 12} phases in Mg-6Al-4Sm alloy, and there were (Mg, Al){sub 2}Ca, Al{sub 2}Ca and Al{sub 2}Sm phases in Mg-6Al-2Ca-2Sm alloy. In addition, the addition of alloying elements including Ca and Sm, especially the composite addition, could significantly improve the tensile properties of Mg-6Al alloy. Compared to Mg-6Al alloy, the tensile strengths of Mg-6Al-2Ca-2Sm alloy at 448, 473 and 498 K were enhanced by 50.32, 87.92, and 94.99%, respectively. Furthermore, when the stretching temperatures were 448 and 473 K, the fracture pattern of Mg-6Al-2Ca-2Sm alloy was the mixture of intergranular fracture and trans-crystalline fracture. However, when the stretching temperature was 498 K, the fracture pattern of Mg-6Al-2Ca-2Sm alloy was the intergranular fracture.

36 MATERIALS SCIENCE↗

Effect of Al-Si Coating on Weld Microstructure and Properties of 22MnB5 Steel Joints for Hot Stamping

22MnB5 hot stamping steels are gradually being used in tailor-welded blank applications. In this experiment, 1-mm-thick Al-Si coated and de-coated 22MnB5 steels were laser-welded and then hot-stamped. The chemical compositions, solidification process, microstructure and mechanical properties were investigated to reveal the effect of Al-Si coating and heat treatment. In the welded condition, the coated joints had an Al content of approximately 2.5 wt.% in the fusion zone and the de-coated joints had 0.5 wt.% Al. The aluminum promoted the δ-ferrite formation as the skeletal structure during solidification. In the high-aluminum weld, the microstructure consisted of martensite and long and band-like δ-ferrite. Meanwhile, the low-aluminum weld was full of lath martensite. After the hot stamping process, the δ-ferrite fraction increased from 10 to 24% in the coated joints and the lath martensite became finer in the de-coated joints. The tensile strengths of the coated joints or de-coated joints were similar to that before hot stamping, but the strength of the coated joints was reduced heavily after hot stamping compared to the de-coated joints and base material. The effect of δ-ferrite on the tensile properties became stronger when the fusion zone was soft and deformed first in the hot-stamped specimens. The coated weld showed a brittle fracture surface with many cleavage planes, and the de-coated weld showed a ductile fracture surface with many dimples in hot-stamped conditions.

36 MATERIALS SCIENCE↗

Evaluation of the Role of Metallic Matrix on Environmentally Assisted Embrittlement of Austempered Ductile Iron (ADI) Using High Si Steel

The objective of this work stems from the environmentally assisted embrittlement suffered by austempered ductile iron (ADI) when its surface is submerged in water. This phenomenon leads to a drop in elongation and ultimate tensile strength of about 75% and 10%, respectively, while the 0.2% offset strain stress remains unaffected. Heat-treating a high Si steel, an ausferritic matrix similar to that present in the ADI under study is obtained, yielding giving a very good combination of tensile strength and elongation. In this manner, it was possible to examine the influence of the metallic matrix such as that present in ADI, though without nodules and cell boundaries, also called last to freeze zones (LTF). Tensile test evaluations on ADI and steel samples under dry and wet conditions were carried out. Additionally, a very specific test, introducing surface cracks, was conducted with the purpose of expanding the current knowledge on this particular kind of fracture. Earlier investigations on ADI have suggested that the process of embrittlement starts in a surface crack generated at the early stages of plastic deformation in LTF zones, which results from the solidification process, where pores, inclusions and unreacted austenite are present. In this manner, water penetrates and weakens the material strength, making the crack grow very fast and leading to an instantaneous samples failure. The main results obtained in this work include the confirmation of the deleterious effect of the LTF zones in the embrittlement process and the fracture surface analysis showing characteristic features of this kind of failure.

36 MATERIALS SCIENCE↗

Microstructure, fatigue, and impact toughness properties of additively manufactured nickel alloy 718

A complete understanding of processing-structure-property-performance relationship of additively manufactured (AM) components are critical from an application standpoint. Therefore, in the current investigation, a comprehensive microstructural characterization and mechanical properties (tensile, fatigue and impact toughness) evaluation of nickel alloy 718 AM by the laser powder bed fusion (L-PBF) technique have been performed. AM builds were made from powders manufactured via different atomization conditions. Although the standard post-heat treatment procedure led to the removal of severe interdendritic segregation both grain boundary and intra-grain precipitation of d phase occurred. Regardless of d phase presence, axial fatigue properties of both the AM builds were similar to design handbook wrought fatigue data. However, due to the d phase, impact toughness properties were comparable to the wrought material conditions that exhibited d phase. Fractured surfaces of Charpy impact samples exhibited crack propagation extensively along the boundaries decorated by d precipitates.

Komarasamy, Mageshwari↗

Extracting single fiber transverse and shear moduli from off-axis misalignment fiber tensile testing

Small diameter (<100 μm) fibers (e.g. carbon fibers, Kevlar, and fiberglass) and wires (e.g. ultrafine copper and aluminum wires) are frequently used in many different engineering applications, such as for light weighting structures, electromagnetic shielding for aircraft/infrastructure/EVs, vibration damping, biological sensors, aerospace electrical devices, and electric windings just to name a few. Due to the manufacturing process, the fibers and wires are pulled and stretched to produce a preferential alignment. Therefore, thin fibers and wires typically display different properties along the length of the fiber as opposed to their cross section and many fibers/wires are considered transversely isotropic. The axial properties of fibers/wires can be ascertained via tensile testing of single-filaments or fiber tows, but the radial properties require much more effort to measure. Knowing these properties is important for the accurate prediction of micromechanical models and manipulation of fibers during micromanufacturing. In this paper, a new technique was developed to determine the transverse/shear moduli and strength of a material by conducting tensile tests of the material at increasing misalignment angles from the tensile axis. Due to the transversely isotropic nature of the material, the transverse/shear moduli and strength influence the experimental results recorded by the test machine to different degrees based on the amount of misalignment in the test setup. An equation was derived to determine the influence of each of the material properties based on the misalignment angle by manipulating the stiffness matrix for transversely isotropic materials using the transformation matrices. Then, curve fitted coefficients were used to identify the material properties. Here, the strengths were similarly determined by curve fitting an off-axis Tsai-Hill failure criteria to determine the influence of transverse, shear, and tensile strengths based on the complex loading condition provided by the off-axis tensile test. Zoltek Panex 35 carbon fibers were used to demonstrate this new technique and the determined properties were then compared to those obtained from nanoindentation and from literature. Fracture surfaces provide insight into the different failure mechanisms at various misalignment angles.

36 MATERIALS SCIENCE↗

Mechanical evaluation of WC-Co materials with varying microstructures

Tungsten carbide–cobalt materials are useful in a variety of extreme applications due to a desirable blend of properties, yet the technology has not significantly changed since their initial development in the 1920s. The mechanical properties of this class of materials is highly dependent on two variables, the size of the tungsten carbide grains, and the amount of binder phase present in the final body. In this study, the amount of binder phase is isolated across three commercial materials from the same manufacturer with three different grain sizes to investigate the effect on mechanical properties. The mechanical properties investigated are indentation hardness, flexure and tensile strength, as well as fracture toughness. In general, an increase in hardness and tensile strength with decreasing grain size was observed, while the fracture toughness showed the opposite trend with toughness increasing with increasing grain size. The flexure strength results did not show a correlation to grain size. Fractographic analysis identified the dominant strength-limiting flaw for each sample, which largely were in the form of porosity. Other flaws types, such as inclusions from the milling process, clusters of large grains, and machining cracks from the surface finishing process, were also identified. Finally, Weibull analysis was performed and deemed appropriate for analysis of these materials, but strength-size scaling was not conducted due to the variability in the strength-limiting feature between the different specimen geometries.

36 MATERIALS SCIENCE↗