Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRAG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

An investigation of drag reduction for a standard truck with various modifications

A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a standard truck model. The physical variables included: a cab mounted air deflector; a boattail on the rear of the cargo compartment; flow-vanes on the front of the cargo compartment; and a forebody fairing over the cab. Tests were conducted at yaw angles (relative wind angle) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.4 x 100,000 to 6.1 x 100,000 based upon the equivalent diameter of the vehicles. The forebody fairing and the flow-vane with the closed bottom were very effective in improving the flow over the forward part of the cargo compartment. The forebody fairing provided a calculated fuel saving of 5.6 liters per hour (1.5 gallons per hour) over the baseline configuration for a ground speed of 88.6 km/hr (55 mph) in national average winds.

Muirhead, V. U.↗

Studies of compressible shear flows and turbulent drag reduction

Compressible shear flows and drag reduction were examined and three methods are addressed: (1) the analytical and numerical aspects of conformal mapping were summarized and a new method for computation of these maps is presented; (2) the computer code SPECFD for solution of the three dimensional time dependent Navier-Stokes equations for compressible flow on the CYBER 203 computer is described; (3) results of two equation turbulence modeling of turbulent flow over wavy walls are presented. A modified Jones-Launder model is used in two dimensional spectral code for flow in general wavy geometries.

Orszag, S. A.↗

Flight test evaluation of predicted light aircraft drag, performance, and stability

A technique was developed which permits simultaneous extraction of complete lift, drag, and thrust power curves from time histories of a single aircraft maneuver such as a pull up (from V max to V stall) and pushover (to V max for level flight). The technique, which is an extension of nonlinear equations of motion of the parameter identification methods of Iliff and Taylor and includes provisions for internal data compatibility improvement as well, was shown to be capable of correcting random errors in the most sensitive data channel and yielding highly accurate results. Flow charts, listings, sample inputs and outputs for the relevant routines are provided as appendices. This technique was applied to flight data taken on the ATLIT aircraft. Lack of adequate knowledge of the correct full throttle thrust horsepower true airspeed variation and considerable internal data inconsistency made it impossible to apply the trajectory matching features of the technique.

Smetana, F. O.↗

An investigation of drag reduction for a box-shaped vehicle with various modifications

The influence of physical variables on the aerodynamic drag of a box shaped vehicle model was studied. The physical variables included built-in rounded front corners, and two different designs of add on flow vanes for the front of box shaped vehicle with 67 deg and 90 deg of arc. For a diesel powered vehicle, only slightly larger than a family van, the built in rounded front corners provide a calculated fuel saving of about 6.0 liters per hour of driving (1.6 gallons per hour) at 88.6 km per hour (55 mph) in national average winds, as compared to the baseline vehicle having all square corners. The corresponding savings for a baseline vehicle to which front mounted flow vanes were added is competitive. For a gasoline powered vehicle the volumetric fuel savings would be larger by a factor of about 1.7. The fuel savings for a standard size motor home would be greater for the diesel or gasoline powered vehicles by from 30 to 35 percent because of the larger frontal area. Thus projected fuel savings for a standard size motor home powered by gasoline can approach 12.5 to 13.5 liters (3.3 to 3.6 gallons) for each hour driving at highway speeds.

Muirhead, V. U.↗

Modification in drag of turbulent boundary layers resulting from manipulation of large-scale structures

The effects of placing a parallel-plate turbulence manipulator in a boundary layer are documented through flow visualization and hot wire measurements. The boundary layer manipulator was designed to manage the large scale structures of turbulence leading to a reduction in surface drag. The differences in the turbulent structure of the boundary layer are summarized to demonstrate differences in various flow properties. The manipulator inhibited the intermittent large scale structure of the turbulent boundary layer for at least 70 boundary layer thicknesses downstream. With the removal of the large scale, the streamwise turbulence intensity levels near the wall were reduced. The downstream distribution of the skin friction was also altered by the introduction of the manipulator.

Corke, T. C.↗

Design considerations of advanced supercritical low drag suction airfoils

Supercritical low drag suction laminar flow airfoils were laid out for shock-free flow at design freestream Mach = 0.76, design lift coefficient = 0.58, and t/c = 0.13. The design goals were the minimization of suction laminarization problems and the assurance of shock-free flow at freestream Mach not greater than design freestream Mach (for design lift coefficient) as well as at lift coefficient not greater than design lift coefficient (for design freestream Mach); this involved limiting the height-to-length ratio of the supersonic zone at design to 0.35. High design freestream Mach numbers result with extensive supersonic flow (over 80% of the chord) on the upper surface, with a steep Stratford-type rear pressure rise with suction, as well as by carrying lift essentially in front- and rear-loaded regions of the airfoil with high static pressures on the carved out front and rear lower surface.

Pfenninger, W.↗

Skin friction drag measurements by LDV

A laser Doppler velocimeter employing a microscope objective as the receiving lens has been developed for measuring fluid velocity inside the boundary layer flow field with a spatial resolution of 40 microns. The method was applied for direct measurement of aerodynamic skin friction drag from the measured velocity gradient at the wall. Experimental results obtained on skin friction and on velocity components in a turbulent boundary layer on a low speed wind tunnel showed good agreement with previously reported data using conventional instruments such as hot-wire anemometers and Preston tubes. The method thus provides a tool for measurement and control of skin friction on aerodynamic bodies without perturbing the flow field.

Mazumder, M. K.↗

Correlations Among Ice Measurements, Impingement Rates Icing Conditions, and Drag Coefficients for Unswept NACA 65A004 Airfoil

An empirical relation has been obtained by which the change in drag coefficient caused by ice formations on an unswept NACA 65AO04 airfoil section can be determined from the following icing and operating conditions: icing time, airspeed, air total temperature, liquid-water content, cloud droplet impingement efficiencies, airfoil chord length, and angles of attack. The correlation was obtained by use of measured ice heights and ice angles. These measurements were obtained from a variety of ice formations, which were carefully photographed, cross-sectioned, and weighed. Ice weights increased at a constant rate with icing time in a rime icing condition and at progressively increasing rates in glaze icing conditions. Initial rates of ice collection agreed reasonably well with values predicted from droplet impingement data. Experimental droplet impingement rates obtained on this airfoil section agreed with previous theoretical calculations for angles of attack of 40 or less. Disagreement at higher angles of attack was attributed to flow separation from the upper surface of the experimental airfoil model.

Gray, Vernon H.↗

Numerical studies of laminar and turbulent drag reduction

Two-dimensional incompressible flow over wavy surfaces is studied numerically by spectral methods. Turbulence effects are modeled. Results for symmetric and asymmetric wave forms are presented. Effect of propagating surface waves on drag reduction is studied. Comparisons between computer simulations and experimental results are made.

Balasubramanian, R.↗

Heat loss and drag of spherical drop tube samples

Analysis techniques for three aspects of the performance of the NASA/MSFC 32 meter drop tube are considered. Heat loss through the support wire in a pendant drop sample, temperature history of a drop falling through the drop tube when the tube is filled with helium gas at various pressures, and drag and resulting g-levels experienced by a drop falling through the tube when the tube is filled with helium gas at various pressures are addressed. The developed methods apply to systems with sufficiently small Knudsen numbers for which continuum theory may be applied. Sample results are presented, using niobium drops, to indicate the magnitudes of the effects. Helium gas at one atmosphere pressure can approximately double the amount of possible undercooling but it results in an apparent gravity levels of up to 0.1 g.

Wallace, D. B.↗

Low-drag ground vehicle particularly suited for use in safely transporting livestock

A low-drag truck consisting of a tractor-trailer rig characterized by a rounded forebody and a protective fairing for the gap conventionally found to exist between the tractor and the trailer is described. The fairing particularly suited for establishing an attached flow of ambient air along its surfaces. The truck is also comprised of a forward facing, ram air inlet and duct and a plurality of submerged inlets and outflow ports communicating with the trailer for continuously flushing heated gases from the trailer as the rig is propelled at highway speeds.

Saltzman, E. J.↗

NASA research on viscous drag reduction

Research on natural laminar flow, laminar flow control by suction, and turbulent drag reduction is discussed. Preliminary results suggest that a significant amount of natural laminar flow can be achieved on small, straight wing airplanes. On larger, swept wing aircraft, laminar flow control by distributed suction is expected to result in significant fuel savings. The area over which laminar flow control is applied depends on tradeoffs involving structural complexity, maintenance, and cost. Several methods of reducing turbulent skin friction by altering the turbulence structure itself have shown promise in exploratory testing. The status of these technologies and the benefits of applying them to future aircraft are reviewed.

Petersen, R. H.↗

Electrostatic disturbance forces on a 3-axis drag-free sensor

The electrostatic analysis of a multiple-capacitance 3-axis drag-free sensor is presented in this paper. The instrument consists of a proof-mass (a dense metallic ball) floating freely inside a spherical cavity enclosed by the sensor plates and the shield. Since the ball and the cavity are not necessarily concentric, the problem in three-dimensional potential theory for electrostatics is solved by the method of boundary perturbations and specifically in terms of spherical harmonics. The capacitance outputs of the instrument and the electrostatic forces acting on the system are derived as non-linear functions of the ball position, ball charge and the sensor plate potentials. The instrument sensitivity and cross-coupling effects are discussed. The analysis may also be useful for electrostatic gyros and suspensions.

Hagstrom, T.↗

The role of gravity wave induced drag and diffusion in the momentum budget of the mesosphere

A slight modification of the parameterization suggested by Lindzen (1981) for the zonal drag and eddy diffusion effects generated by breaking internal gravity waves in the mesosphere is tested using a severely truncated midlatitude beta-plane channel model. It is found that realistic mean zonal flow profiles with zonal wind reversals above the mesopause can be simulated for both winter and summer radiative heating conditions provided that a gravity-wave spectrum is assumed which includes both stationary waves and waves of relatively large phase speeds. These results contrast greatly with the unrealistic mean wind profiles produced when Rayleigh friction is used to parameterize the effects of small scale motions on the mean flow.

Holton, J. R.↗

Kevlar/PMR-15 polyimide matrix composite for a complex shaped DC-9 drag reduction fairing

The Aircraft Energy Efficiency (ACEE) Program was established by NASA to improve the fuel efficiency of commercial transport aircraft and thereby to reduce the amount of fuel consumed by the air transportation industry. One of the final items developed by the program is an improved fairing which is the aft closure for the thrust reverser actuators on the JT8D nacelles on DC-9 aircraft. The reduced-drag fairing uses, in the interest of weight savings, an advanced composite construction. The composite material contains Kevlar 49 fibers in a PMR-15 matrix. Attention is given to the aerodynamic configuration, the material system, and aspects of fabrication development.

Kawai, R. T.↗

Miniature drag-force anemometer

A miniature drag-force anemometer is described which is capable of measuring unsteady as well as steady-state velocity head and flow direction. It consists of a cantilevered beam with strain gages located at the base of the beam as the force measuring element. The dynamics of the beam are like those of a lightly damped second-order system with a natural frequency as high as 40 kilohertz depending on beam geometry and material. The anemometer can be used in both forward and reversed flow. Anemometer characteristics and several designs are presented along with discussions of several applications.

Krause, L. N.↗

Minimum Induced Drag of Nonplanar Wings

DRG program incorporates numerical optimization technique for calculating bound-circulation distribution required for minimum induced drag of nonplanar wings. DRG written in FORTRAN IV.

Ku, T. J.↗

Wind-tunnel measurements of the chordwise pressure distribution and profile drag of a research airplane model incorporating a 17-percent-thick supercritical wing

The Langley 8-foot transonic pressure tunnel to determine the wing chordwise pressure distribution for a 0.09-scale model of a research airplane incorporating a 17-percent-thick supercritical wing. Airfoil profile drag was determined from wake pressure measurements at the 42-percent-semispan wing station. The investigation was conducted at Mach numbers from 0.30 to 0.80 over an angle-of-attack range sufficient to include buffet onset. The Reynolds number based on the mean geometric chord varied from 2 x 10 to the 6th power at Mach number 0.30 to 3.33 x 10 to the 6th power at Mach number 0.65 and was maintained at a constant value of 3.86 x 10 to the 6th power at Mach numbers from 0.70 to 0.80. Pressure coefficients for four wing semispan stations and wing-section normal-force and pitching-moment coefficients for two semispan stations are presented in tabular form over the Mach number range from 0.30 to 0.80. Plotted chordwise pressure distributions and wake profiles are given for a selected range of section normal-force coefficients over the same Mach number range.

Ferris, J. C.↗