Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Flight Investigation of the Stability and Control Characteristics of Vertically Rising Airplane Research Model with Swept or Unswept Wings and X- or +-tails

The take-off, landing, hovering, and transition flight characteristics of a propeller-driven, fighter-type, vertically rising airplane model were obtained from time histories of the flights and from the pilots' opinions of the flight characteristics. In general, there were no major differences in the behavior of any of the configurations, all of which performed satisfactorily.

CONTROL, LATERAL↗
NASA NTRS1948

Effects of a sweptback hydrofoil on the force and longitudinal stability characteristics of a typical high-speed airplane

An investigation was conducted in the Langley 8-foot high-speed tunnel to determine the effects of a sweptback hydrofoil on the force and longitudinal stability characteristics of a typical high-speed airplane. The Mach number range for this investigation was from 0.60 to 0.95 and at M = 1.20. The effects of the hydrofoil on the lift, drag, and pitching-moment characteristics are presented.

AIRPLANES - COMPONENTS IN COMBINATION↗
NASA NTRS1948

The Effect of Negative Dihedral, Tip Droop, and Wing-tip Shape on the Low-speed Aerodynamic Characteristics of a Complete Model Having a 45 Degrees Sweptback Wing

An investigation has been conducted in the Langley 300 MPH 7- by 10-foot tunnel to determine the effect of negative dihedral, tip droop, and wing-tip shape on the low-speed aerodynamic characteristics of a complete model having a 45 degrees sweptback wing. Longitudinal and lateral stability characteristics were obtained for the model with and without tail surfaces.

STABILITY, LONGITUDINAL - STATIC↗
NASA NTRS1949

Investigation of a Thin Straight Wing of Aspect Ratio 4 by the NACA Wing-flow Method : Lift and Pitching-moment Characteristics of the Wing Alone

This report presents measurements of the lift and pitching-moment characteristics of a straight wing of aspect ratio 4, taper ratio 0.5, having a symmetrical double-wedge airfoil section with a maximum thickness of 4.4-percent chord. The tests were conducted in the Mach number range 0.51 to 1.20, Reynolds numbers 380,000 to 660,000, by the NACA wing-flow method. The results are compared with theory and with wind-tunnel tests of a similar model. It is indicated that in the Mach number range 0.82 to 1.00 the model surface, profile, and test Reynolds number all would be very important considerations in any attempt to study or predict full-scale characteristics from small-model tests.

MACH NUMBER EFFECTS - COMPLETE WINGS↗
NASA NTRS1950

Preliminary analysis of problem of determining experimental performance of air-cooled turbine I : methods for determining heat-transfer characteristics

In determining the experimental performance of an air-cooled turbine, the heat-transfer characteristics must be evaluated. The suggested formulas that are required to determine these characteristics are presented. The formulas have a form in which dependent parameters are expressed as unknown functions of independent parameters. Methods of experimenting to determine these functions are suggested. In some cases general heat-transfer discussions that lead to the suggested forms of the formulas are given.

TURBINE COOLING↗
NASA NTRS1950

The Longitudinal Stability, Control Effectiveness, and Control Hinge Moment Characteristics Obtained from a Flight Investigation of a Canard Missile Configuration at Transonic and Supersonic Speeds

A 60 degree delta wing canard missile configuration was flight-tested at the Langley pilotless aircraft research station at Wallops Island, Va. The results include the longitudinal stability derivatives, control effectiveness, drag characteristics, and control-surface hinge-moment characteristics for a Mach number range of 0.7 to 1.45.

Niewald, Roy J↗
NASA NTRS1951

Characteristics of a wedge with various holder configurations for static-pressure measurements in subsonic gas streams

The characteristics of a wedge static-pressure sensing element with various holder configurations were determined and compared with the characteristics of the conventional tube. The probes were tested over a range of Mach number from 0.3 to 0.95 and at various pitch and yaw angles. The investigation showed that the spike-mounted wedge sensing element has a pressure coefficient comparable with the conventional subsonic static-pressure probe and the pressure coefficient of the wedge varied less than that of the conventional probe for corresponding change of yaw angle.

Gettelman, Clarence C↗
NASA NTRS1954

Preliminary Investigation of Performance and Starting Characteristics of Liquid Fluorine : Liquid Oxygen Mixtures with Jet Fuel

The performance of jet fuel with an oxidant mixture containing 70 percent liquid fluorine and 30 percent liquid oxygen by weight was investigated in a 500-pound-thrust engine operating at a chamber pressure of 300 pounds per square inch absolute. A one-oxidant-on-one-fuel skewed-hole impinging-jet injector was evaluated in a chamber of characteristic length equal to 50 inches. A maximum experimental specific impulse of 268 pound-seconds per pound was obtained at 25 percent fuel, which corresponds to 96 percent of the maximum theoretical specific impulse based on frozen composition expansion. The maximum characteristic velocity obtained was 6050 feet per second at 23 percent fuel, or 94 percent of the theoretical maximum. The average thrust coefficient was 1.38 for the 500-pound thrust combustion-chamber nozzle used, which was 99 percent of the theoretical (frozen) maximum. Mixtures of fluorine and oxygen were found to be self-igniting with jet fuel with fluorine concentrations as low as 4 percent, when low starting propellant flow rated were used.

ENGINES, ROCKET↗
NASA NTRS1951

Steady-state Engine Windmilling and Engine Speed Decay Characteristics of an Axial-flow Turbojet Engine

A wind tunnel investigation has been conducted to determine the steady-state windmilling and engine speed decay characteristics of the J34-WE-32 turbo-jet over a range of altitudes from 5000 to 50,000 feet and simulated flight Mach numbers from 0.19 to 1.06. The effect of an engine accessory load on the speed decay characteristics was also determined. The accessory load was about 7.8 horsepower for engine speeds above 4000 rpm and decreased with decreasing engine speed. An analysis of the speed decay data was made and engine speed decay rates were determined for hypothetical accessory loads up to 40 horsepower.

ENGINES, TURBOJET - ALTITUDE TESTS↗
NASA NTRS1952

Performance Characteristics of a Normal-shock Side Inlet Located Downstream of a Canard Control Surface at Mach Numbers of 1.5 and 1.8/

The performance characteristics of a downward canted normal-shock side (scoop) inlet located downstream of a triangular control surface are presented for free-stream Mach numbers of 1.5 and 1.8 in terms of total pressure recovery and mass flow ratio for various boundary-layer removal systems,angles of attack, control surface deflections and adverse yaw. An engine operating condition for a hypothetical turbojet engine is established, and the match point characteristics of the engine-inlet configuration are summarized. 520::It is shown that the diffuser performance increases with increased boundary-layer removal and decreases because of the presence of the wake from the forward control surface. At the higher angles of attack the wake passes over the inlet and does not affect the inlet performance. Adverse yaw reduces the total pressure recovery values below those for the unawed case. Magnitudes of the total pressure recovery were below the theoretical normal-shock recovery for the respective test Mach numbers.

INLETS, SIDE - DUCTED BODIES↗
NASA NTRS1953

Acceleration of high-pressure-ratio single-spool turbojet engine as determined from component performance characteristics I : effect of air bleed at compressor outlet

An analytical investigation was made to determine from component performance characteristics the effect of air bleed at the compressor outlet on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Consideration of several operating lines on the compressor performance map with two turbine-inlet temperatures showed that for a minimum acceleration time the turbine-inlet temperature should be the maximum allowable, and the operating line on the compressor map should be as close to the surge region as possible throughout the speed range. Operation along such a line would require a continuously varying bleed area. A relatively simple two-step area bleed gives only a small increase in acceleration time over a corresponding variable-area bleed. For the modes of operation considered, over 84 percent of the total acceleration time was required to accelerate through the low-speed range ; therefore, better low-speed compressor performance (higher pressure ratios and efficiencies) would give a significant reduction in acceleration time.

ENGINES, TURBOJET↗
NASA NTRS1953

Force and pressure-recovery characteristics at supersonic speeds of a conical nose inlet with bypasses discharging outward from the body axis

Aerodynamic and performance characteristics of a conical spike nacelle-type inlet with two bypasses are presented at Mach numbers of 1.6, 1.8, and 2.0 for angles of attach up to 90 degrees. The bypasses were located 6 inlet diameters downstream of the inlet and were designed to discharge the bypass mass flow outward from the body axis. The inlet was designed to attain a mass-flow ratio of unity at a Mach number of 2.0. It is shown that discharging the bypass mass flow outward from the body nearly doubles the critical drag of a similar configuration but with bypass discharge in an axial direction. As a result of this greater drag, the net force on the model in the flight direction is reduced when comparison is made with the axial discharge case. The lift and pitching-moment coefficients are slightly higher than those for a configuration without bypasses. Approximately 25 % of the maximum inlet mass flow was discharged through the bypasses, and the pressure-recovery and mass-flow characteristics were in qualitative and quantitative agreement with the results of an investigation of a similar configuration with axial discharge.

DIFFUSERS, SUBSONIC↗
NASA NTRS1953

A Flight Study of the Effects on Tracking Performance of Changes in the Lateral-oscillatory Characteristics of a Fighter Airplane

A study of the effects of variations in lateral-oscillatory characteristics on air-to-air tracking performance has been made, using a conventional, propeller-driven fighter airplane equipped with servo devices for varying these characteristics in flight. Tracking runs were made both in smooth air and in simulated rough air. The lateral-oscillation period, damping, and roll coupling were varied over wide ranges during the investigation.

GUSTS, TURBULENCE↗
NASA NTRS1954

Altitude Performance and Operational Characteristics of an XT38-A-2 Turboprop Engine

The overall engine performance and the starting and windmilling characteristics of an XT38-A-2 turboprop engine have been investigated in the NACA Lewis altitude wind tunnel. The simulated flight conditions ranged from altitudes of 5000 to 45,000 feet at a flight Mach number of 0.30 and from Mach numbers of 0.301 to 0.557 at an altitude of 35,000 feet. The engine, equipped with a standard-area exhaust nozzle, was operated with independent control of fuel flow and propeller pitch; operation was thereby allowed over a wide range of engine conditions. Windmilling characteristics were obtained at altitudes of 15,000 feet and 35,000 feet. Analysis of the performance maps obtained at each flight condition revealed that both altitude and flight Mach number had a major effect on corrected engine variables. The large reductions in corrected shaft horsepower occurring when the altitude was increased were the result of decreases in compressor and turbine efficiencies. Windmilling engine starts were made at altitudes as high as 35,000 feet at an engine speed of 2000 rpm.

Essig, R H↗
NASA NTRS1954

Thrust and drag characteristics of a convergent-divergent nozzle with various exhaust jet temperatures

An investigation was conducted in the 8-by-6 foot supersonic wind tunnel on the effect of exhaust-gas temperatures on the external and internal characteristics of a convergent-divergent nozzle having an area expansion ratio of 1.83. Data were obtained over a pressure-ratio range from 1 to 20 at free-stream Mach numbers of 1.6 and 2.0 for exhaust temperatures of 860 degrees, 1650 degrees, and 2000 degrees R. Results of this investigation indicated that generally both the internal and external performance characteristics were only slightly affected by a large change in jet temperature. The small differences in performance which did occur were predicted satisfactorily from theoretical considerations.

Hearth, Donald P↗
NASA NTRS1954

Investigation of Thrust and Drag Characteristics of a Plug-type Exhaust Nozzle

An investigation was conducted in the 8- by 6-foot supersonic wind tunnel on the external and internal characteristics of a plug-type exhaust nozzle. Two positions of the center plug, one simulating a convergent nozzle and the other a convergent-divergent nozzle, were investigated. Data were obtained at free-stream Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a pressure-ratio range of 1 to 20 and angles of attack of zero and 8 degrees. Results of this investigation indicated that the plug nozzle had thrust-minus-drag performance over the entire pressure-ratio range comparable with equivalent conventional nozzles. The effect of the exhaust jet on the external aerodynamics was similar to results observed for conventional nozzles. In addition, the thrust characteristics were generally insensitive to external flow and good agreement was noted with data obtained on comparable plug nozzles in quiescent air.

Hearth, Donald P↗