Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CFD simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

A Study on Computational Cost Reduction of Simulations of Phase-Change Material (PCM) Embedded Heat Exchangers

Thermal storage can be implemented using Phase-Change Materials (PCM), which absorb significant latent heat with a relatively small temperature change. PCM phase-change processes are transient and are driven by thermal diffusion and natural convection – the latter, especially for melting process. Modeling and simulation of PCM heat exchangers (HX’s) is typically computationally intensive due to the relatively complex time-dependent physics. Most of the PCM modeling work in the literature uses high-order modeling tools such as Computational Fluid Dynamics (CFD) and Lattice-Boltzmann Method (LBM). For design purposes, the existing PCM modeling approaches are not practical, limiting researchers in their ability to investigate new ideas and different PCM’s with faster turnarounds. This paper presents a study investigating the reduction of computational cost of PCM embedded HX’s CFD models by evaluating the feasibility of spatial reduction without losing accuracy. The analysis consists of comparing full and partial domain under full melting conditions. The subject of this study is a single straight tube with circular transverse fins in the vertical orientation, using PCM’s with 35oC nominal melting temperature. Different tube and fin dimensions are investigated. Results indicate that the reduced domain reproduces - in half the run time - the same behavior as the full domain since the buoyancy effects are localized and patterned. The outputs from the partial domain simulation were used to build a non-general correlation for the PCM heat transfer characteristics and demonstrated how it can be implemented in a Finite Control Volume Reduced Order Model (ROM). The ROM can accurately reproduce the CFD simulations at 4 to 5 orders of magnitude faster.

25 ENERGY STORAGE↗

Tuning Process for the Modified Magnussen Combustion Model

In the application of CFD to turbulent reacting flows, one of the main limitations to predictive accuracy is the chemistry model. Using a full or skeletal kinetics model may provide good predictive ability, however, at considerable computational cost. Adding the ability to account for the interaction between turbulence and chemistry improves the overall fidelity of a simulation but adds to this cost. An alternative is the use of simple models, such as the Magnussen model, which has negligible computational overhead, but lacks general predictive ability except for cases that can be tuned to the flow being solved. In this paper, a technique will be described that allows the tuning of the Magnussen model for an arbitrary fuel and flow geometry without the need to have experimental data for a particular case. The tuning is based on comparing the results of the Magnussen model and full finite-rate chemistry when applied to perfectly and partially stirred reactor sim- ulations. In addition, a modification to the Magnussen model is proposed that allows the upper kinetic limit for the reaction rate to be set, giving better physical agreement with full kinetic mechanisms. In order to improve the agreement with flame temperatures, the thermal properties of the product species is adjusted to better match the mixture proper- ties of the full mechanism. The combustion model is then applied to the simulation of a representative scramjet flowpath, and the results compared to experimental data and other kinetic models. This procedure allows a simple reacting model to be used in a predictive manner, and affords significant savings in computational costs for CFD simulations.

Norris, A. T.↗

Chapter 6: Modeling and Simulation of Wind-Farm Flows

The subject of this chapter is the modeling and simulation of the flow through full wind farms, also known as wind plants, which are collections of many wind turbines within a region working together to supply power to the grid like any other type of power plant. This topic is interesting and exciting because of the increasing variety of and uses for wind plant flow modeling and simulation. For example, Figure 6.1 shows the computed flow field from a high-fidelity simulation of the Lillgrund offshore wind farm using computational fluid dynamics (CFD) with large-eddy simulation (LES) turbulence modeling and actuator line rotor aerodynamics models. There are many ways to model this type of flow, ranging from very simple models of wind turbine wakes and their interactions that can run in a matter of seconds on a laptop to high-fidelity, turbulence -resolving LES of the atmospheric flow and wakes that require days of use of thousands of cores on a high-performance computing cluster. The uses of wind plant flow simulations are equally varied. Wind plant layout designers run hundreds or thousands of simulations over all possible wind directions and speeds using simple models to predict a future wind plant's annual energy production. Researchers use LESs of the wind plant to study phenomena such as wind turbine wake interactions with each other and with the atmospheric boundary layer (ABL). As computational resources become more readily available, it is even becoming common for turbine manufacturers to use CFD of some form to model wind plants in complex terrain to help in the wind turbine siting and selection process. We are beginning to see the expensive, high-fidelity tools being used to create data and knowledge that improves or enables the creation of new cheaper, lower fidelity tools. We are also beginning to see the low- and high-fidelity tools used together to perform uncertainty quantification of energy estimates and optimization of wind plant layouts. As new computing technologies mature, such as graphics processing unit (GPU)-based computing, the future of full wind plant flow modeling is exciting.

17 WIND ENERGY↗

A Multi-Year Plan for Enhancing Turbulence Modeling in Hydra-TH Revised and Updated Version 2.0

The purpose of this report is to document a multi-year plan for enhancing turbulence modeling in Hydra-TH for the Consortium for Advanced Simulation of Light Water Reactors (CASL) program. Hydra-TH is being developed to the meet the high- fidelity, high-Reynolds number CFD based thermal hydraulic simulation needs of the program. This work is being conducted within the thermal hydraulics methods (THM) focus area. This report is an extension of THM CASL milestone L3:THM.CFD.P10.02 [33] (March, 2015) and picks up where it left off. It will also serve to meet the requirements of CASL THM level three milestone, L3:THM.CFD.P11.04, scheduled for completion September 30, 2015. The objectives of this plan will be met by: maturation of recently added turbulence models, strategic design/development of new models and systematic and rigorous testing of existing and new models and model extensions. While multi-phase turbulent flow simulations are important to the program, only single-phase modeling will be considered in this report. Large Eddy Simulation (LES) is also an important modeling methodology. However, at least in the first year, the focus is on steady-state Reynolds Averaged Navier-Stokes (RANS) turbulence modeling.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Multi-Year Plan for Enhancing Turbulence Modeling in Hydra-TH

The purpose of this milestone report is to document a multi-year plan for enhancing turbulence modeling in Hydra-TH. In Phase II of the Consortium for Advanced Simulation of Light Water Reactors (CASL) program, Hydra-TH is being developed to the meet the high-fidelity, high-Reynolds number CFD based thermal hydraulic simulation needs of the program. This work will be conducted within the thermal hydraulics methods (THM) focus area. This objective will be met by; maturation of recently added models, strategic design/development of new models and systematic and rigorous testing of existing and new models and model extensions. This report will also serve to meet the requirements of CASL level three milestone, L3:THM.CFD.P10.02, scheduled for completion March 31, 2015.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Unsteady Three-Dimensional Simulation of a Shear Coaxial GO2/GH2 Rocket Injector with RANS and Hybrid-RAN-LES/DES Using Flamelet Models

Historically, the analysis and design of liquid rocket engines (LREs) has relied on full‐scale testing and one‐dimensional empirical tools. The testing is extremely expensive and the one‐dimensional tools are not designed to capture the highly complex, and multi‐dimensional features that are inherent to LREs. Recent advances in computational fluid dynamics (CFD) tools have made it possible to predict liquid rocket engine performance, stability, to assess the effect of complex flow features, and to evaluate injector‐driven thermal environments, to mitigate the cost of testing. Extensive efforts to verify and validate these CFD tools have been conducted, to provide confidence for using them during the design cycle. Previous validation efforts have documented comparisons of predicted heat flux thermal environments with test data for a single element gaseous oxygen (GO2) and gaseous hydrogen (GH2) injector. The most notable validation effort was a comprehensive validation effort conducted by Tucker et al. [1], in which a number of different groups modeled a GO2/GH2 single element configuration by Pal et al [2]. The tools used for this validation comparison employed a range of algorithms, from both steady and unsteady Reynolds Averaged Navier‐Stokes (U/RANS) calculations, large‐eddy simulations (LES), detached eddy simulations (DES), and various combinations. A more recent effort by Thakur et al. [3] focused on using a state‐of‐the‐art CFD simulation tool, Loci/STREAM, on a two‐dimensional grid. Loci/STREAM was chosen because it has a unique, very efficient flamelet parameterization of combustion reactions that are too computationally expensive to simulate with conventional finite‐rate chemistry calculations. The current effort focuses on further advancement of validation efforts, again using the Loci/STREAM tool with the flamelet parameterization, but this time with a three‐dimensional grid. Comparisons to the Pal et al. heat flux data will be made for both RANS and Hybrid RANSLES/ Detached Eddy simulations (DES). Computation costs will be reported, along with comparison of accuracy and cost to much less expensive two‐dimensional RANS simulations of the same geometry.

Westra, Doug G.↗

Numerical and Experimental Investigations on the Ignition Behavior of OME

On the path towards climate-neutral future mobility, the usage of synthetic fuels derived from renewable power sources, so-called e-fuels, will be necessary. Oxygenated e-fuels, which contain oxygen in their chemical structure, not only have the potential to realize a climate-neutral powertrain, but also to burn more cleanly in terms of soot formation. Polyoxymethylene dimethyl ethers (PODE or OMEs) are a frequently discussed representative of such combustibles. However, to operate compression ignition engines with these fuels achieving maximum efficiency and minimum emissions, the physical-chemical behavior of OMEs needs to be understood and quantified. Especially the detailed characterization of physical and chemical properties of the spray is of utmost importance for the optimization of the injection and the mixture formation process. The presented work aimed to develop a comprehensive CFD model to specify the differences between OMEs and dodecane, which served as a reference diesel-like fuel, with regards to spray atomization, mixing and auto-ignition for single- and multi-injection patterns. The simulation results were validated against experimental data from a high-temperature and high-pressure combustion vessel. The sprays’ liquid and vapor phase penetration were measured with Mie-scattering and schlieren-imaging as well as diffuse back illumination and Rayleigh-scattering for both fuels. To characterize the ignition process and the flame propagation, measurements of the OH* chemiluminescence of the flame were carried out. Significant differences in the ignition behavior between OMEs and dodecane could be identified in both experiments and CFD simulations. Liquid penetration as well as flame lift-off length are shown to be consistently longer for OMEs. Zones of high reaction activity differ substantially for the two fuels: Along the spray center axis for OMEs and at the shear boundary layers of fuel and ambient air for dodecane. Additionally, the transient behavior of high temperature reactions for OME is predicted to be much faster.

33 ADVANCED PROPULSION SYSTEMS↗

Simulations of biomass pyrolysis using glued-sphere CFD-DEM with 3-D intra-particle models

The shape of biomass particles influences intra-particle heat transfer, particle-particle collisions, interphase momentum, heat transfer, and pyrolysis yield. In this research, the effects of these multi-scale phenomena are captured using a glued-sphere computational fluid dynamic discrete element method (CFD-DEM) with 3-D intra-particle models. The glued-spheres resolved the shapes of particles and intra-particle temperature and species distributions. The implementation was validated using the pyrolysis data of a spherical particle and a cylindrical particle. Then, the influences of biomass shapes and sizes on pyrolysis were investigated. The results revealed the significant influence of surface areas and mass distributions on interphase heat transfer and chemical reactions. The intra-particle heat transfer is neglectable for a Biot number smaller than 0.41. Finally, the pyrolysis of irregularly shaped biomass particles in a fixed bed, fluidized bed, and spouted bed was simulated. Analysis of conversion distributions showed the largest deviations in the fixed bed and the slowest conversion rate in the spouted bed. A good balance between uniform and fast conversion is achieved in the fluidized bed. The multi-scale method proposed in this research provides a tool for the evaluation of large irregular-shaped biomass particle pyrolysis in different types of reactors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of Novel PEM Membrane and Multiphase CD Modeling of PEM Fuel Cell

To understand heat and water management phenomena better within an operational proton exchange membrane fuel cell's (PEMFC) conditions, a three-dimensional, two-phase computational fluid dynamic (CFD) flow model has been developed and simulated for a complete PEMFC. Both liquid and gas phases are considered in the model by taking into account the gas flow, diffusion, charge transfer, change of phase, electro-osmosis, and electrochemical reactions to understand the overall dynamic behaviors of species within an operating PEMFC. The CFD model is solved numerically under different parametric conditions in terms of water management issues in order to improve cell performance. The results obtained from the CFD two-phase flow model simulations show improvement in cell performance as well as water management under PEMFCs operational conditions as compared to the results of a single phase flow model available in the literature. The quantitative information obtained from the two-phase model simulation results helped to develop a CFD control algorithm for low temperature PEM fuel cell stacks which opens up a route in designing improvement of PEMFC for better operational efficiency and performance. To understand heat and water management phenomena better within an operational proton exchange membrane fuel cell's (PEMFC) conditions, a three-dimensional, two-phase computational fluid dynamic (CFD) flow model has been developed and simulated for a complete PEMFC. Both liquid and gas phases are considered in the model by taking into account the gas flow, diffusion, charge transfer, change of phase, electro-osmosis, and electrochemical reactions to understand the overall dynamic behaviors of species within an operating PEMFC. The CFD model is solved numerically under different parametric conditions in terms of water management issues in order to improve cell performance. The results obtained from the CFD two-phase flow model simulations show improvement in cell performance as well as water management under PEMFCs operational conditions as compared to the results of a single phase flow model available in the literature. The quantitative information obtained from the two-phase model simulation results helped to develop a CFD control algorithm for low temperature PEM fuel cell stacks which opens up a route in designing improvement of PEMFC for better operational efficiency and performance.

08 HYDROGEN↗

High-fidelity simulation-driven model development for coarse-grained computational fluid dynamics

Nuclear reactor safety analysis requires analysis of a broad range of accident scenarios and determining their consequences. For a nuclear power plant behavior, it is impossible to obtain experimental data at sufficiently large scales to support calibration and validation of various system models. In single-phase flow convective problems, high-resolution methods of Computational Fluid Dynamics (CFD) such as Direct Numerical Simulation (DNS) and Large Eddy Simulation (LES) can provide high fidelity results under conditions where physical measurements are unavailable. However, such high-resolution simulations are computationally expensive and not suitable for simulation of long transient scenarios in nuclear reactor accidents. In this work, we investigate the use of a high fidelity simulation-driven approach to model sub-grid scale (SGS) effect in Coarse Grained Computational Fluid Dynamics CG-CFD. Notably, fine-mesh simulations are used to construct physics-informed statistical surrogate of coarse-mesh SGS model. For an initial analysis, we consider a case of turbulent natural convection in a volumetrically heated fluid layer with a thermally insulated lower boundary and isothermal upper boundary. This scenario of unstable stratification is relevant to turbulent natural convection in a severe nuclear reactor accident, as well as in containment mixing and passive cooling. For this type of flow, the SGS effect is modeled by an added turbulent diffusivity in the energy equation. It is shown that a global correction for the energy equation is sufficient to achieve a significant improvement to the CG-CFD prediction of thermal mixing in the fluid layer. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A CFD Framework for Film Boiling and Quenching in Cryogenic Chilldown

Tests of cryogenic chilldown in a vertical stainless-steel tube are simulated using computational fluid dynamics (CFD). Subcooled liquid nitrogen enters a room-temperature tube at one end, resulting in film boiling and eventual quenching of the tube walls. A CFDbased modeling framework employing the mixture multiphase model was developed to simulate this chilldown process and was applied to validate it against experimental data. Extensive sensitivity studies have been performed to create a consistent modeling framework, and a range of test conditions are simulated to assess the modeling capability. The importance of the rewetting temperature and its relation to the foam limit temperature is discussed and considered in the CFD framework. The presented results demonstrate a qualitatively consistent representation of the film boiling and quenching regime. However, the quantitative accuracy of the simulations varies with the test conditions. In addition, simulated distributions of the vapor volume fraction are presented, but the current lack of experimental volume fraction data prevents comparisons.

Computational Fluid Dynamics↗

A CFD Framework for Film Boiling and Quenching in Cryogenic Chilldown

Tests of cryogenic chilldown in a vertical stainless-steel tube are simulated using computational fluid dynamics (CFD). Subcooled liquid nitrogen enters a room-temperature tube at one end, resulting in film boiling and eventual quenching of the tube walls. A CFDbased modeling framework employing the mixture multiphase model was developed to simulate this chilldown process and was applied to validate it against experimental data. Extensive sensitivity studies have been performed to create a consistent modeling framework, and a range of test conditions are simulated to assess the modeling capability. The importance of the rewetting temperature and its relation to the foam limit temperature is discussed and considered in the CFD framework. The presented results demonstrate a qualitatively consistent representation of the film boiling and quenching regime. However, the quantitative accuracy of the simulations varies with the test conditions. In addition, simulated distributions of the vapor volume fraction are presented, but the current lack of experimental volume fraction data prevents comparisons.

Computational Fluid Dynamics↗

Machine Learning Assisted Safety Modeling and Analysis of Advanced Reactors

With the advances in computational power and numerical methods, analysts can now rely on first-principle simulations to predict ultra-fine details in a variety of applications. Advances in machine learning (ML) have produced algorithms that can now learn high-level abstractions via hierarchical models. This project aims to leverage advances in ML techniques and the available high-resolution simulation data to develop a novel modeling and simulation (M\&S) methodology for reactor safety analysis. While application-agnostic ML techniques are available, complex physics constraints need to be incorporated into ML techniques to build ML-based closures for computationally efficient predictive simulations. This project intends to develop a physics-guided data-driven multi-scale methodology for M\&S of advanced reactors. The project focuses on thermal fluid (T/F) phenomena, which play major roles in advanced reactor safety. Specifically, we propose a data-driven coarse-mesh turbulence model based on local flow features for the transient analysis of thermal mixing and stratification in a sodium-cooled fast reactor (SFR). The model has a coarse-mesh setup to ensure computational efficiency, while it is trained by fine-mesh computational fluid dynamics (CFD) data with Reynolds-averaged Navier-Stokes (RANS) turbulence model to ensure accuracy. Three different neural networks are developed and tested for loss-of-flow transients in the hot pool of SFR, i.e. the densely connected convolutional neural network (DCNN), long-short-term-memory network based on proper orthogonal decomposition (POD-LSTM), and the DCNN informed by LSTM (DCNN-LSTM). The performances of these three neural networks are evaluated based on baseline models. The DCNN-LSTM model has been chosen for further hyperparameter optimization. Furthermore, based on a simplified two-dimensional case, uncertainty quantification (UQ) of the developed ML-based closure are investigated with three methods, i.e. Monte Carlo dropout, deep ensemble, and Bayesian neural network. The developed ML-based turbulent viscosity closure relation based on deep ensemble is then integrated into the system analysis module SAM and serves as a term in the conservation equations. Such a SAM-ML based procedure guarantees that the obtained results are consistent with the physical constraints of the thermal-fluid system. The SAM-ML simulation on the same loss-of-flow transient showed comparable accuracy with the CFD simulation but with a much coarser mesh setup. Last but not least, the ML-based closure improvement with the support of higher-fidelity data from large eddy simulation (LES) is discussed. As a first step towards this direction, a baseline LES simulation is performed to obtain comparable data with RANS results. Based on the early results, future investigation on further improving the ML-based closure is discussed. We believe the developed approach that combines scientific machine learning with nuclear system analysis code can benefit the advanced reactor community as more accurate safety analyses will better characterize reactor safety margins and reduce licensing efforts.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Multidimensional Numerical Modeling of Combustion Dynamics in a Non-Premixed Rotating Detonation Engine With Adaptive Mesh Refinement

In the present work, a novel computational fluid dynamics (CFD) methodology was developed to simulate full-scale non-premixed rotating detonation engines (RDEs). A unique feature of the modeling approach was the incorporation of adaptive mesh refinement (AMR) to achieve a good trade-off between model accuracy and computational expense. Here, unsteady Reynolds-averaged Navier–Stokes (RANS) simulations were performed for an Air Force Research Laboratory (AFRL) non-premixed RDE configuration with hydrogen as fuel and air as the oxidizer. The finite-rate chemistry model, along with a ten-species detailed kinetic mechanism, was employed to describe the H 2 -Air combustion chemistry. Three distinct operating conditions were simulated, corresponding to the same global equivalence ratio of unity but different fuel/air mass flowrates. For all conditions, the capability of the model to capture essential detonation wave dynamics was assessed. An exhaustive verification and validation study was performed against experimental data in terms of a number of waves, wave frequency, wave height, reactant fill height, oblique shock angle, axial pressure distribution in the channel, and fuel/air plenum pressure. The CFD model was demonstrated to accurately predict the sensitivity of these wave characteristics to the operating conditions, both qualitatively and quantitatively. A comprehensive heat release analysis was also conducted to quantify detonative versus deflagrative burning for the three simulated cases. The present CFD model offers a potential capability to perform rapid design space exploration and/or performance optimization studies for realistic full-scale RDE configurations.

42 ENGINEERING↗

Numerical Optimization of Spray-Guided Spark Assistance for Cold Idle Operation in a Heavy-Duty Gasoline Compression Ignition Engine

This article describes the results of a response surface model (RSM)-based numerical optimization campaign for spray-guided spark assistance at cold operations in a heavy-duty gasoline compression ignition (GCI) engine. On the basis of an earlier work on spark-assisted GCI cold combustion, a space-filling design of experiments (DoE) method was first undertaken to investigate a multitude of hardware design variables and engine operating parameters. The main design variables included the number of injector nozzles, fuel split quantities and injection timings, and spark timing. The objective variables were engine combustion efficiency (ŋ c ), maximum pressure rise rate (MPRR), and engine-out nitrogen oxide (NO x ) emissions. A total of 150 design candidates were automatically generated using the Sobol sequence method provided by the commercial software package, CAESES. Then, closed-cycle computational fluid dynamic (CFD) spark-assisted GCI simulations under cold idling operations were performed. The outcomes from the CFD-DoE design campaign were utilized to construct high-fidelity RSMs that allowed for further design optimization of the spark plug- and fuel injector-related design variables, along with fuel injection strategy parameters. A merit function with respect to objective variables was formulated with an appropriate weight assignment on each objective variable. Finally, the best design candidate was identified from the RSM-based optimization process and further validated in the CFD analysis. The best design candidate showed the potential to significantly improve combustion efficiency (ŋ c > 90%) over the baseline at cold idle while satisfying MPRR and NOx emissions constraints (MPRR < 5 bar/CAD and NO x < 4.5 g/kWh).

33 ADVANCED PROPULSION SYSTEMS↗

Validation and Development of a Fast-Running CFD Model for the No-Vent Fill of Liquid Propellant Tank

Cryogenic fluids, while offering higher energy density than storable propellants, present several handling challenges, including gradual boil-off and tank self-pressurization. Transferring these propellants between tanks can be problematic, as the receiving tank's temperature and pressure often lead to flashing and rapid boil-off upon injection. The No-Vent Fill (NVF) technique mitigates these risks by preventing liquid fuel from being expelled overboard. By controlling tank pressure and ensuring appropriate condensation in the ullage region, the NVF process avoids exceeding vent pressure limits. In this study, Loci/STREAM-VOF simulations were compared with data from NASA K-site test runs on a 2.1 cubic meter tank with a bottom orifice under various no-vent fill conditions, including different wall temperatures, flow rates, and inlet liquid temperatures. The effort demonstrated that Loci/STREAM-VOF is capable of quantitatively capturing the important physics of NVF with submerged jets: (1) validation of the liquid-vapor interface turbulence velocity using previous experimental data showed good agreement at different fill levels; (2) validation of the CFD Stanton number for mass transfer provided an adequate mass transfer coefficient range; (3) consistent pressure agreements were found in the pressure history for both cold and warm conditions; and (4) the variations of final pressure with flow rate and inlet liquid temperature were well predicted by the CFD simulation. The application of NVF for low-gravity conditions will be studied in future work.

CFD↗

Validation and Development of a Fast-Running CFD Model for the No-Vent Fill of Liquid Propellant Tank

Cryogenic fluids, while offering higher energy density than storable propellants, present several handling challenges, including gradual boil-off and tank self-pressurization. Transferring these propellants between tanks can be problematic, as the receiving tank's temperature and pressure often lead to flashing and rapid boil-off upon injection. The No-Vent Fill (NVF) technique mitigates these risks by preventing liquid fuel from being expelled overboard. By controlling tank pressure and ensuring appropriate condensation in the ullage region, the NVF process avoids exceeding vent pressure limits. In this study, Loci/STREAM-VOF simulations were compared with data from NASA K-site test runs on a 2.1 cubic meter tank with a bottom orifice under various no-vent fill conditions, including different wall temperatures, flow rates, and inlet liquid temperatures. The effort demonstrated that Loci/STREAM-VOF is capable of quantitatively capturing the important physics of NVF with submerged jets: (1) validation of the liquid-vapor interface turbulence velocity using previous experimental data showed good agreement at different fill levels; (2) validation of the CFD Stanton number for mass transfer provided an adequate mass transfer coefficient range; (3) consistent pressure agreements were found in the pressure history for both cold and warm conditions; and (4) the variations of final pressure with flow rate and inlet liquid temperature were well predicted by the CFD simulation. The application of NVF for low-gravity conditions will be studied in future work.

CFD↗

Influences of yaw angle and turbulence intensity on the performance of a 20 kW in-stream hydrokinetic turbine

Herein three-dimensional transient CFD (Computational Fluid Dynamics) simulations are performed to study the hydrodynamic performance of an ocean current turbine with a 3.0 m diameter 3-bladed rotor. Simulations are based on the RANS (Reynolds Averaged Navier–Stokes) equations and the shear stress transport k-ω turbulent model is utilized. The influence of yaw angle and upstream TI (turbulence intensity) on the turbine performance is studied. The CFD method is first validated using existing experimental data and good agreement is obtained. The performance of the turbine, including power, thrust and wake characteristics are then studied at different TSR (tip speed ratios). The turbine obtains a maximum coefficient of power (C p ) of 0.4642 at TSR = 6 and the coefficient of thrust (C t ) increases over the entire evaluated TSR range to a value of 0.8788 at a TSR = 10. Simulations are also performed at four different yaw angles, 0°, 5°, 10° and 15° which show that both C p and C t decrease as yaw angle increases. Finally simulations of three different TIs, 3%, 6% and 9%, are performed and analyzed. Results show that TI minimally affects C p and C t for the considered TI range, but greatly influences the downstream wake structure.

13 HYDRO ENERGY↗