Results for “Batch” — Page 77

DOE OSTI2025

Enhanced H 2 production from subsurface through organic acids stimulation

Geologic hydrogen (H₂) generation through serpentinization of ultramafic rocks presents a promising alternative to conventional hydrogen production, utilizing Earth's abundant magnesium- and iron-rich minerals. This study explores the use of short-chain organic acids (specifically malic acid, MA; and citric acid, CA) to enhance hydrogen yields by stimulating mineral dissolution and iron oxidation from ultramafic rock samples. Batch experiments were conducted with crushed peridotite samples from the Tamarack Complex (Minnesota) and Del Puerto Ophiolite (California). Experiments employed 0.05 M and 0.1 M solutions of MA or CA, under 500 psi (35 bar) nitrogen pressure, at temperatures up to 150 °C. Real-time gas monitoring, aqueous chemistry and solid-phase analyses were performed to track reaction progress and hydrogen production.

08 HYDROGEN↗

DOE OSTI2025

Operation of Argonne's Liquid Salt-Liquid Metal Separation Testbed for U/TRU Product Processing

Argonne National Laboratory has constructed a liquid salt-liquid metal separation testbed for use in the development and advancement of cathode processing of U/TRU co‑deposits generated by pyroprocessing of used nuclear fuel. The U/TRU product recovered from the electrorefiner contains adhered and entrained salt that must be removed prior to consolidation of the U/TRU alloy for use in advanced reactor fuel fabrication. The bottom pour operation utilizes the low melting points of U/TRU co‑deposits and higher densities of molten metals compared to molten salts to separate and consolidate the U/TRU product. Argonne’s testbed is designed to support the development and optimization of bottom-pouring configurations for batch and semi-continuous operations, integration of process monitoring and control technologies, and determination of operational requirements for implementing in an industrial setting. Scoping tests were performed to demonstrate operational aspects of the testbed, including operation using single-pour spout and dual-pour spout configurations, effectiveness of salt containment and extent of salt vaporization, and the use of sensor probes to detect the location of the interface between the metal and salt phases during pouring. Recommendations for process optimization testing for further development of bottom pour processing to separate U/TRU alloys from adhered salt were made based on the results of scoping tests. Completing the recommended activities will increase the technical readiness level (TRL) of the liquid salt-liquid metal separation operation and consolidation of U/TRU alloys to support industrialization of pyroprocessing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Flexible Fuel Electric Hybrid Glass Furnace Demonstration

The furnace contractor completed General Arrangement (GA) layouts and Piping and Instrumentation Diagrams (P&ID) for both furnaces during this reporting period. Preliminary equipment lists accompanied this work. Control system architecture in progress. Key furnace design elements and deliverables on track to be complete by end of phase. The facilities design and integration contractor completed a 3D scan and modeling of the facility. The work during this period focused on preliminary design with a focus on overall project scope and feasibility. This key work supports the overall project deliverables for 30% preliminary engineering and Preliminary Design Report (PDR) which are on track to be complete by the end of the phase. These deliverables are approximately 50% complete through the end of this reporting period. The batch house operations design contractor continues development of site plan and General Arrangement (GA) layout to support the 30% preliminary engineering and design package. This work is 60% complete by the end of this reporting period and is on track to be complete by the end of the phase.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

A Zero-Emission Process for Direct Reduction of Iron by Hydrogen Plasma in a Rotary Kiln Reactor

This project’s goal was to demonstrate a hydrogen plasma (H-plasma)-rotary kiln process for reducing iron ore to iron as part of the steel manufacturing process. The H-plasma provides a greater thermodynamic driving force for reducing iron ores than thermal processes such as the DRI process, enabling lower reaction temperatures. We estimated that our process technology can reduce energy consumption by 45% compared to the blast furnace process and ~15% compared to the DRI process. Steel manufacturing produces about 1.8 tons of CO2/ton of steel with iron ore reduction accounting for about one-third of the CO2 produced in the overall manufacturing process. We estimated our process has the potential to reduce GHG emissions from ironmaking by 35% with today’s grid and by up to 88% with a future low-carbon grid while being cost competitive with the current blast furnace route. We demonstrated reduction of hematite and magnetite rich materials at temperatures from 600 to 800°C. We achieved 90-95% metallization on 100 gr samples in batch reduction experiments in the H-plasma rotary kiln furnace at 600-650°C. Attempts to perform tests in a continuous operation mode identified problems with the ore feed mechanism. We identified solutions but there was not time nor budget to correct these for this project

36 MATERIALS SCIENCE↗

DOE OSTI2025

FY25 MOOSE Usability Improvements: 3D Meshing Capabilities, Initiation of Geometry Support for Monte Carlo Tools, and Enhancement of MOOSE/Workbench User Input Interactions

Usability improvements have been made to MOOSE and Workbench in FY25 to enhance usability and user workflows. Assorted enhancement have been made to MOOSE’s intrinsic meshing capabilities in order to enable more flexible and complex meshing of nuclear reactor systems, in particular for 3D applications. Mesh generators have been added to perform operations such as batch mesh generation, surface mesh generation, and creation of 3D transition layers. These mesh generation capabilities make it much easier to generate high quality non-extruded 3D meshes. Additionally, work to integrate Monte Carlo reactor physics simulations into MOOSE-based multi-physics workflows has reached another milestone with the implementation of the Constructive Solid Geometry (CSG) base framework. This framework lays the foundation for mesh generators to offer the user a generic CSG output option (as opposed to a finite element mesh). To support users, workshop on the MOOSE Reactor Module was delivered which featured hands-on examples using the NEAMS Workbench on INL’s High Performance Computing system. Recent updates to the NEAMS Workbench, WASP, and the MOOSE language server have introduced several improvements aimed at making MOOSE-based simulation setup and input management faster, more accurate, and easier to use. Key capabilities that have been added include multi-tab-stop autocompletion, visual input diagnostics, developer-directed data visualizations, upgraded ParaView integration, and Workspace-level file tracking. Together, these changes make it easier for users to build, validate, and manage complex MOOSE-based simulation models — especially those involving reusable components, included files, and datasets. The improvements are designed to save time, reduce input errors, and help users get to a successful simulation run faster, with more confidence in the results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

A Zero-Emission Process for Direct Reduction of Iron by Hydrogen Plasma in a Rotary Kiln Reactor

This project’s goal was to demonstrate a hydrogen plasma (H-plasma)-rotary kiln process for reducing iron ore to iron as part of the steel manufacturing process. The H-plasma provides a greater thermodynamic driving force for reducing iron ores than thermal processes such as the DRI process, enabling lower reaction temperatures. We estimated that our process technology can reduce energy consumption by 45% compared to the blast furnace process and ~15% compared to the DRI process. Steel manufacturing produces about 1.8 tons of CO2/ton of steel with iron ore reduction accounting for about one-third of the CO2 produced in the overall manufacturing process. We estimated our process has the potential to reduce GHG emissions from ironmaking by 35% with today’s grid and by up to 88% with a future low-carbon grid while being cost competitive with the current blast furnace route. We demonstrated reduction of hematite and magnetite rich materials at temperatures from 600 to 800°C. We achieved 90-95% metallization on 100 gr samples in batch reduction experiments in the H-plasma rotary kiln furnace at 600-650°C. Attempts to perform tests in a continuous operation mode identified problems with the ore feed mechanism. We identified solutions but there was not time nor budget to correct these for this project

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Nanostructured Alumina Forming Austenitic Alloy (NAFA) Production using Advanced Manufacturing

Alumina-forming austenitic (AFA) alloys are well known for their exceptional corrosion-resistant properties due to the formation of a dense oxide scale beneficial in their application as a nuclear material. However, use of the alloys in core material applications is limited due to the high nickel-transmutation and helium generation rate in service, leading to swelling and reduced lifetimes. Enhancing the sink strength to pin gas bubbles and increasing gas management of the material may mitigate many of the degradation phenomena expected during alloy deployment (such as high-temperature helium embrittlement and cavity swelling for lead-cooled fast-reactor applications). Nanostructured materials are usually produced using a time-consuming and expensive batch process like mechanical alloying to achieve the fine homogenous distribution of nanoprecipitates throughout the matrix material. Integrating the nanoprecipitates in modern additive manufacturing processes has proven difficult, as the required nano-sizes or number densities cannot be achieved simultaneously. Efforts to increase the number density of precipitates by adding more precipitate-forming rare-earth elements led to agglomeration of such elements, while the nano-sized precipitates did not form in sufficient quantity when not enough rare-earth element was use. In this work a novel approach to advanced manufacturing and the fabrication of Nanostructured AFA (NAFA) materials was chosen. A dual precipitate-forming NAFA steel with a chemistry more suitable for advanced reactor applications was produced to create an environmentally resistant, high-sink-strength austenitic alloy for advanced reactor cladding applications.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Multiphysics Modeling of Microreactors with NEAMS codes, and Validation Based on KRUSTY Reactivity Insertion

The NEAMS Multiphysics Applications team continues to assess code usability and functionality for microreactor design and safety analyses, while demonstrating that NEAMS tools capture both steady-state and transient behavior across distinct microreactor concepts. In FY2025, the team advanced full-core, high-fidelity, multiphysics models that solve more complex problems and strengthen verification/validation for several microreactor systems: heat-pipe microreactor (HPMR), gas-cooled microreactor (GCMR), and the KRUSTY experiment. These models employ the MOOSE MultiApp/Transfers architecture with Griffin for neutronics, BISON for heat conduction/thermomechanics, Sockeye for heat pipes, SAM/THM for coolant channels and loops, and SWIFT for hydride behavior, with meshes generated via the MOOSE Reactor Module. The graphite models available in the Grizzly code were also investigated for future analyses. For the HPMR, a Na-HPMR variant was constructed to align with recently validated heat-pipe experiments and Sockeye’s LCVF capability, enabling mechanistic heat-pipe transients and startup modeling. The Na-HPMR will serve as the primary model for HPMR investigations in upcoming tasks. The load-following and single heat-pipe failure scenarios (Griffin/BISON/Sockeye), which were previously modeled for the K-HPMR, were replicated for the Na-HPMR, showing strong negative temperature feedback and highly localized thermal effects, respectively, while the startup case captured vapor-front progression and heat-removal activation. Solid mechanics was added to the previously built K-HPMR full-core model in BISON, showing minimal impact on steady-state reactivity yet enabling stress-field predictions that prepare the path for full-core TRISO performance analyses. For the GCMR, automated steady-state and four transient scenarios were executed using Griffin/BISON/SAM/SWIFT. Results confirm robust inherent safety: power collapses promptly in loss-of-cooling events, the inlet-temperature drop settles to a new equilibrium, and a single-channel blockage yields only a ~30 K local fuel-temperature rise with <0.4% power decrease. SWIFT-predicted hydrogen redistribution affects reactivity during both steady-state and transient conditions, underscoring its importance. A Brayton-cycle balance of plant (BOP) model in SAM/THM demonstrated stable startup behavior, and xenon-driven reactivity during load following was analyzed. To improve TRISO-compact temperature fidelity, a fast multiscale Heat Source Decomposition (HSD) treatment was implemented. Against heterogeneous benchmarks, HSD reduces underprediction of kernel temperatures and lowers predicted peak powers in reactivity-insertion transients compared to previous homogenized models. KRUSTY warm-critical validation progressed from FY2024 baselines: the 15Ȼ insertion shows excellent agreement in peak power (~2% high) and temperature trends, and the 30Ȼ case was automated via a feedback controller that maintained power near 3 kW for ~150 s with close agreement to data. The successful modeling of the warm critical tests has laid a strong foundation for simulating more complex nuclear system tests in the years ahead. Throughout FY2025, developer feedback was provided (e.g., MOOSE batch mesh generation, distributed pre-split meshes, Griffin sweeper on displaced meshes), several new models were contributed to the Virtual Test Bed, and an OECD-NEA WPRS multiphysics benchmark based on the HPMR was initiated to enable broader cross-comparison and best-practice development with the nuclear community at large.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Depletion Analysis of a Generic Fast Spectrum Molten Salt Reactor Supporting Material Control and Accounting (Rev.1)

Advanced reactors are of interest for a variety of use scenarios, and there are numerous advanced reactor designs being considered, which includes molten salt reactors (MSRs). Depending on the design, advanced reactors may have more extensive material control and accounting (MC&A) processes than current Light Water Reactor (LWR) designs. This project evaluated the use of Monte Carlo simulations for generating information that could guide the development of MC&A approaches for MSRs. In particular, the current capabilities of MCNP version 6.3 internally coupled with CINDER’90 were assessed for a fast spectrum liquid fueled MSR with online fission product removal and refueling. The fission product removal and refueling was performed in batches, and a Python wrapper was developed to control the simulations and update the fuel composition.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Hybrid HEFA-HDCJ Process for the Production of Jet Fuel Blendstocks

The hydrotreatment of bio-oil derived from the pyrolysis and biocrude from hydrothermal liquefaction of lignocellulosic materials to produce hydrocarbons faces significant technological challenges, mainly due to the high reactivity and poor thermal stability of bio-oil, resulting in the formation of large quantities of coke. This problem has been addressed by existing PNNL patents with a two-step hydrotreatment technology in which the bio-oil is first stabilized with a noble hydrogenation metal (often Pt or Ru). Then, in the second step, the bio-oil is deoxygenated with a Ni-Mo or Co-Mo sulfide catalyst. The main problem with this approach is that the Pt/Ru catalysts deactivate easily in the presence of S or other impurities, which are commonly present in pyrolysis oils. In this project, we explored technological solutions to mitigate coke formation, avoiding the use of Pt/Ru catalysts. Our strategy is based on three actions: (1) Bio-oil stabilization in the presence of alcohols. In this project, we studied the stabilization with butanol. (2) the use of a cosolvent to solubilize the bio-oil. Because coke formation reactions are second-order reactions a reduction in the concentration of reactive bio-oil molecules. In this case, we used yellow greases as a co-solvent. (3) Separation of bio-oil reactive fractions. In this project, we studied the removal of water-soluble fractions. Our batch co-hydrotreatment studies confirmed that the addition of butanol and methanol and the blend with lipids effectively contributed to mitigating coke formation (reducing coke yield to about 1 wt.% %). The removal of sugars did not have a noticeable effect on the overall coke yield, suggesting that coke precursors are present in all bio-oil fractions.

09 BIOMASS FUELS↗

DOE OSTI2025

Neptunium (V) Solubility in WIPP Brine: Presence and Absence of WIPP-Relevant Organic and Inorganic Ligands

The oxidation state and solubility of neptunium (Np) in 5 M NaCl and high ionic strength synthetic WIPP (Waste Isolation Pilot Plant) brines were systematically investigated as a function of pCH+ (7-11) in the presence and absence of WIPP-relevant organic ligands, including EDTA (Ethylenediaminetetraacetic acid), oxalate, citrate, and acetate, as well as inorganic ligands such as borate and carbonate at a temperature of 23 ± 2°C. This study was conducted through long-term batch solubility experiments spanning approximately 950 days, using an undersaturation approach. A comprehensive set of experimental and spectroscopic techniques, including UV-VIS-NIR spectroscopy and Np L III -edge X-ray Absorption Spectroscopy (XAS), was employed to identify the solubility-controlling Np solid phases and the predominant aqueous Np species present in the samples.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Report on Updated Properties Handbook of Printed Stainless Steel 316

This report focuses on summarizing mechanical behavior of 316H stainless steel (SS) printed using laser powder bed fusion (LPBF). 316H SS is one of the six alloys that has been qualified for use in nuclear reactors. The Advanced Materials and Manufacturing Technologies (AMMT) program has identified the use of the additive manufacturing (AM) process of LPBF as one of the manufacturing modalities to fabricate components for nuclear applications. Unlike wrought material, AM material displays significant heterogeneity in properties, resulting from changes in process parameters, machine-to-machine variability, and minor changes in feedstock chemistry from one batch to another. Although significant work has been done on 316L SS in the literature and has been summarized in several review papers, very limited data exist on 316H SS. Therefore, this report aims to provide a concise summary of the properties of 316H SS printed using different machines and at different locations as a part of the AMMT program.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Nanostructured Alumina-Forming Austenitic Alloy (NAFA) Production Using Advanced Manufacturing

Alumina-forming austenitic (AFA) alloys are well known for their exceptional corrosion-resistant properties due to the formation of a dense oxide scale beneficial in their application as a nuclear material. However, use of the alloys in core material applications is limited due to the high nickel-transmutation and helium generation rate in service, leading to swelling and reduced lifetimes. Enhancing the sink strength to pin gas bubbles and increasing gas management of the material may mitigate many of the degradation phenomena expected during alloy deployment (such as high-temperature helium embrittlement and cavity swelling for lead-cooled fast-reactor applications). Nanostructured materials are usually produced using a time-consuming and expensive batch process like mechanical alloying to achieve the fine homogenous distribution of nanoprecipitates throughout the matrix material. Integrating the nanoprecipitates in modern additive manufacturing processes has proven difficult, as the required nano-sizes or number densities cannot be achieved simultaneously. Efforts to increase the number density of precipitates by adding more precipitate-forming rare-earth elements led to agglomeration of such elements, while the nano-sized precipitates did not form in sufficient quantity when not enough rare-earth element was use. In this work a novel approach to advanced manufacturing and the fabrication of Nanostructured AFA (NAFA) materials was chosen. A dual precipitate-forming NAFA steel with a chemistry more suitable for advanced reactor applications was produced to create an environmentally resistant, high-sink-strength austenitic alloy for advanced reactor cladding applications.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Develop High-Throughput Workflows for Whole-Genome Sequencing and Insertion Site Screening (CRADA Final Report)

The engineering of microbes for biomanufacturing (e.g. of fuels, chemicals, materials) applications has advanced to a stage where researchers screen genetic libraries with millions of variations each for those with enhanced productivity. This screening, however, can be slow and expensive, as screening individual variants in a high-throughput yet cost-effective manner is challenging. In this project, we aimed to reduce by 3-fold costs associated with the sequencing aspects of the screening process (to determine which genetic variant is responsible for an observed change in productivity), while being able to process over 1,000 samples per batch.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2025

Develop High-Throughput Workflows for Whole-Genome Sequencing and Insertion Site Screening

The engineering of microbes for biomanufacturing (e.g. of fuels, chemicals, materials) applications has advanced to a stage where researchers screen genetic libraries with millions of variations each for those with enhanced productivity. This screening, however, can be slow and expensive, as screening individual variants in a high-throughput yet cost-effective manner is challenging. In this project, we aimed to reduce by 3-fold costs associated with the sequencing aspects of the screening process (to determine which genetic variant is responsible for an observed change in productivity), while being able to process over 1,000 samples per batch.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2025

OLCF’s Advanced Computing Ecosystem (ACE): FY25 Update for Ongoing Efforts

The advent of widespread use of artificial intelligence (AI) and machine learning (ML) models in science, coupled with fast data production rates of scientific instruments strain the traditional batch-oriented high-performance computing (HPC) environment. As scientific exploration continues to require more data and faster processing and analysis, new emerging technologies and capabilities to enable cross-facility and time-sensitive workflows are required for seamless integration of HPC and experimental facilities. The Advanced Computing Ecosystem (ACE) is a strategic initiative within the Oak Ridge Leadership Computing Facility (OLCF) established in 2024 to support the development of cutting-edge technologies to advance computational research and infrastructure at OLCF and across the Department of Energy (DOE). Several DOE initiatives are spearheading the evolution of the scientific landscape by blurring facility boundaries and connecting the user facilities to advance scientific capabilities and ensure energy dominance. The DOE Integrated Research Infrastructure (IRI) program is one example that is laying a foundation to support complex cross-facility workflows. The IRI program aims to integrate diverse computational resources, data infrastructures, and scientific instruments to facilitate collaboration and accelerate scientific discovery. The Interconnected Science Ecosystem (INTERSECT) initiative at Oak Ridge National Laboratory (ORNL) is another example that aims to revolutionize scientific research through AI-driven, interconnected autonomous laboratories and research facilities. Finally, the American Science Cloud (AmSC), recently announced in the “One Big Beautiful Bill”, aims to leverage prior infrastructure efforts of the IRI and automation and AI efforts of INTERSECT (and others) to build a federated, AI-augmented AmSC platform to unify the DOE’s computing, experimental, and data resources to catalyze scientific innovation.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Small Scale Melter Testing of HLW Algorithm Glasses: Matrix 1 Tests

The principal objectives of the DM100 tests were to determine the effects of glass property extremes (glass viscosity, electrical conductivity, and T1%), minimum and maximum concentrations of several major and minor glass components, +/-15% batching errors in the addition of Glass Forming Chemicals (GFCs) to the feed, and variation in the sources of boron and sodium used in the GFCs on processing rates and melter conditions (off-gas characteristics, glass processing, foaming, cold cap, etc.) at constant bubbling rate.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

The potential for New Mexico basalts to sequester CO 2 with a focus on critical element mobility

This study evaluates the potential of New Mexico basaltic rocks and mafic mine waste for CO₂ sequestration via mineral carbonation. Batch experiments up to 200 days at 40°C simulated CO₂-bearing fluid interactions with various crushed basaltic materials at different grain sizes. Results showed that 70–80% of injected CO₂ was mineralized, with the finest grain sizes showing the most rapid and effective drawdown. The experiments also assessed the mobility of critical metals (Cu, Ni, Zn, Co), revealing trends tied to mineral dissolution and secondary mineral formation. The findings support the dual potential of mine waste for CO₂ sequestration and critical element recovery, informing future carbon capture and resource upcycling strategies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗