Results for “surface conditioning” — Page 76

DOE OSTI2021

High-Temperature Multi-Process Sensor Development and Demonstration at Coalfired Power Plants

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2022

Full-scale Demonstration of Multi-process Sensor at a Cycling PC-fired Boiler

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2021

High-Temperature Multi-Process Sensor Development and Demonstration at a Full-scale PC Combustion System

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of coal-fired utility boilers in this project but can be applied to many other industries and applications as well. This project leveraged the existing electrochemical noise-based monitoring system and the new sensor design is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data is transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, the three mMPMS were installed at a full-scale pulverized coal-fired plant, PacifiCorp’s Hunter 3. The systems were demonstrated over 20,000 hours at the plant during regular operation. Also, the sensor data was fed to the plant’s advanced process control system to evaluate the corrosion control by the operation changes and utilized to understand the impacts of load cycling with different ramping up and down speeds. At the end of the project, the systems were converted to the permanent installation at the power plant to be used with the advanced process control system installed at the plant.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

DOE OSTI2022

Characterizing the Geometry and Quantifying the Impact of Nanoscopic Electrocatalyst/Semiconductor Interfaces under Solar Water Splitting Conditions

The materials that are receiving the most attention in photoelectrochemical water splitting are metallic nanoparticle electrocatalysts (np-EC) attached to the surface of a semiconductor (SC) light absorber. In these multicomponent systems, the interface between the semiconductor and electrocatalysts critically affects performance. However, the np-EC/SC interface remains poorly understood as it is complex on atomic scales, dynamic under reaction conditions, and inaccessible to direct experimental probes. This contribution sheds light on how the electrocatalyst/semiconductor interface evolves under reaction conditions by investigating the behavior of nickel electrocatalysts (as nanoparticles and films) deposited on silicon semiconductors. Rigorous electrochemical experiments, interfacial atomistic characterization, and computational modeling are combined to demonstrate critical links between the atomistic features of the interface and the overall performance. It is shown that electrolyte-induced atomistic changes to the interface lead to (1) modulation of the charge carrier fluxes and a dramatic decrease in the electron/hole recombination rates and (2) a change in the barrier height of the interface. Additionally, the critical roles of nonidealities and electrocatalyst coverage due to interfacial geometry are explored. Each of these factors must be considered to optimize the design of metal/semiconductor interfaces which are broadly applicable to photoelectrocatalysis and photovoltaic research.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Numerical Analysis of Liquid Metal MHD Flow and Heat Transfer for Open-Surface Li Divertor in FNSF

Within the ongoing U.S.-based program on the development of liquid metal plasma-facing components, numerical simulations and analyses are performed to address the feasibility of the open-surface Li divertor. In the previous scoping studies (Smolentsev, 2021), heat-removal capabilities of the divertor were assessed using a simplified flow model for a slug-type velocity profile and constant flow thickness. Here, new analyses take into account forces acting on the flowing Li layer. Three reduced-order mathematical models are applied under the conditions of the U.S. Fusion Nuclear Science Facility (FNSF) to access magnetohydrodynamic (MHD) flow development effects, velocity distribution, and surface waves: 1) fully developed MHD flow; 2) quasi-2-D developing MHD flow; and 3) multiphase MHD flow. The obtained results for MHD flows and the surface heat flux computed with the plasma code scrape-off layer plasma simulation for ITER (SOLPS-ITER) are then used as input data to compute the temperature distribution in the divertor by solving the convection–diffusion energy equation.

Smolentsev, Sergey↗

DOE OSTI2026

Syngas Production at Si Hybrid Photoelectrodes Modified with Re(I) and Mn(I) Tricarbonyl Phenanthroline Complexes Containing Reactive Aryl Azide Groups

We installed molecular CO 2 reduction (CO 2 R) catalysts directly onto Si (photo)electrodes. The highly reactive M(5-azido-1,10-phenanthroline)(CO) 3 X (where M = Mn or Re, X = Br or Cl) complexes readily bubbled when dissolved in polar organic solvents, in both the presence and absence of an ultraviolet light source. When placed on hydrogen-terminated Si (H-Si) and native silicon oxide (SiOx), similar amounts of the complex were attached to the surface under illumination (367 nm, 50–200 mW/cm 2 ) or in the dark. Surprisingly, these films revealed submonolayer coverages instead of the multilayered structures we expected. DFT analyses support monolayer formation, showing that the triplet-state nitrene of the complex is more energetically favorable than the singlet state. Using controlled-potential electrolysis experiments, we showed that Re- and Mn-containing films on pSi photoelectrodes generated small amounts of CO when exposed to 1 atm of CO 2 and 1 sun illumination. These amounts of CO were an order of magnitude greater than control surfaces, producing 5.59 × 10 –7 mol CO/h for Re(az-phen) and 7.83 × 10 –7 mol CO/h for Mn(az-phen) films. Much of the charge passed at the pSi electrodes was consumed by the competing hydrogen evolution reaction, which we attribute to the low molecular coverage and the presence of native oxide on the electrode surface after attachment. Finally, this work demonstrates the feasibility of reacting azide-containing ligands with Si surfaces. Still, it highlights the need for alternative ligand structures and reaction conditions to form multilayer films.

azides↗

DOE OSTI2022

Elucidating CO Oxidation Pathways on Rh Atoms and Clusters on the “29” Cu 2 O/Cu(111) Surface

We report single-atom catalysts have attracted a great deal of attention due to their distinct reactivity and potential for cost savings. However, despite the wealth of literature in recent years, identifying the exact nature of the active sites and associated reaction mechanisms remains challenging in many cases. Herein, we take a surface science approach to understand how Rh single atoms and small clusters behave on the thin film “29” Cu 2 O grown on Cu(111). We find that in contrast to Pt, which is present solely as single atoms on the “29” Cu 2 O surface, Rh atoms and clusters coexist and each enable low-temperature CO oxidation, but via different pathways. Specifically, the single Rh atoms produce CO 2 at 444 K via a Mars van Krevelen mechanism whereas the Rh clusters can also dissociate CO, as demonstrated via isotope labeling, and liberate CO 2 at 313 K. Density functional theory (DFT) calculations quantify the energetics of these different pathways and demonstrate that only extended Rh is capable of CO dissociation. Low-temperature scanning tunneling microscopy (STM) reveals that unlike Pt atoms on the same surface, which stay atomically dispersed, the distribution of Rh structures is dependent on pretreatment conditions. DFT calculations reveal the greater tendency of Rh atoms to cluster than Pt, and STM image simulations confirm the active sites. Ambient pressure X-ray photoelectron spectroscopy studies on the same single crystal model systems demonstrate that 1% of a monolayer of Rh on the “29” Cu 2 O thin film significantly accelerates its reduction by CO at 400 K, thus confirming the ultrahigh vacuum surface science findings. Together, these results illustrate how well-defined single crystal experiments are useful in building structure–function relationships that elucidate the reactivity of different ensemble sizes with a level of detail beyond what is possible with high surface area catalysis.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Diagnosis of PV Cell Antireflective Coating Degradation Resulting From Hot-Humid High-Voltage Potential Aging

Corrosion of the antireflective coating on a photovoltaic cell ("ARc corrosion") has previously been observed in studies using hot-humid test conditions with external high-voltage (HV) bias. This study primarily focuses on known vulnerable legacy aluminum back surface field cells in mini-modules (MiMos) put through comparative stepped stress tests. Each cell type had MiMos at +1500 V, -1500 V, or unbiased ("Voc") potential, which were sequentially subjected to test conditions of 60 degrees C/60% relative humidity (RH) for 96 h, as in International Electrotechnical Commission Technical Specification 62804-1; 70 degrees C/70% RH for 200 h; and 85 degrees C/85% RH for 200 h. Characterizations at each step included visual camera and electroluminescence (EL) imaging, colorimetry, and current-voltage curve tracing. Final characterizations included: Suns-Voc, spatial mapping of external quantum efficiency, high-resolution photoluminescence, EL, and dark lock-in thermography imaging. Forensics were performed on extracted cores, including scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy, and scanning Auger microscopy (SAM). Forensics were also conducted on MiMos from previous studies that underwent stepped HV aging and separate outdoor aged full-sized modules. ARc corrosion was specifically seen for the glass/encapsulant/cell side of the +1500 V (HV+) stressed MiMos and modules. Appearance, color, and reflectance were the most distinguishing characteristics relative to glass corrosion, gridline corrosion and delamination, and other concurrent degradation modes. SEM/EDS and SAM identified the conversion of silicon nitride to hydrated silica, hydrous silica, or hydrated amorphous silica, which preferentially occurred at the edges and tips of the pyramidal textured cell surface.

14 SOLAR ENERGY↗

DOE OSTI2024

Understanding the Influence of Urban Form on the Spatial Pattern of Precipitation

Urban areas are known to modify the spatial pattern of precipitation climatology. Existing observational evidence suggests that precipitation can be enhanced downwind of a city. Among the proposed mechanisms, the thermodynamic and aerodynamic processes in the urban lower atmosphere interact with the meteorological conditions and can play a key role in determining the resulting precipitation patterns. In addition, these processes are influenced by urban form, such as the impervious surface extent. This study aims to unravel how different urban forms impact the spatial patterns of precipitation climatology under different meteorological conditions. We use the Multi-Radar Multi-Sensor quantitative precipitation estimation data products and analyze the hourly precipitation maps for 27 selected cities across the continental United States from the years 2015–2021 summer months. Results show that about 80% of the studied cities exhibit a statistically significant downwind enhancement of precipitation. Additionally, we find that the precipitation pattern tends to be more spatially clustered in intensity under higher wind speed; the location of radial precipitation maxima is located closer to the city center under low background winds but shifts downwind under high wind conditions. The magnitude of downwind precipitation enhancement is highly dependent on wind directions and is positively correlated with the city size for the south, southwest, and west directions. This study presents observational evidence through a cross-city analysis that the urban precipitation pattern can be influenced by the urban modification of atmospheric processes, providing insight into the mechanistic link between future urban land-use change and hydroclimates.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Competing Intermolecular and Molecule–Surface Interactions: Dipole–Dipole-Driven Patterns in Mixed Carborane Self-Assembled Monolayers

Carboranedithiol isomers adsorbing with opposite orientations of their dipoles on surfaces are self-assembled together to form mixed monolayers where both lateral dipole–dipole and lateral thiol–thiolate (S–H···S) interactions provide enhanced stability over single-component monolayers. Here, we demonstrate the first instance of the ability to map individual isomers in a mixed monolayer using the model system carboranedithiols on Au{111}. The addition of methyl groups to one isomer provides both an enhanced dipole moment and extra apparent height for differentiation via scanning tunneling microscopy (STM). Associated computational investigations rationalize favorable interactions of mixed pairs and the associated stability changes that arise from these interactions. Both STM images and Monte Carlo simulations yield similarly structured mixed monolayers, where approximately 10% of the molecules have reversed dipole moment orientations but no direct chemical attachment to the surface, leading to homogeneous monolayers with no apparent phase separation. Deprotonating the thiols by depositing the molecules under basic conditions eliminates the lateral S–H···S interactions while accentuating the dipole–dipole forces. The molecular system investigated is composed of isomeric molecules with opposite orientations of dipoles and identical surface packing, which enables the mapping of individual molecules within the mixed monolayers and enables analyses of the contributions of the relatively weak lateral interactions to the overall stability of the assemblies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

The pH-dependent orientation of N3 dye on a gold substrate is revealed using heterodyne-detected vibrational sum frequency generation spectroscopy

We report on systematic changes to the adsorption geometry of the dye N3 {[cis-bis(isothiocyanato)bis(2,2' -bipyridyl-4,4' -dicarboxylato ruthenium(II)]} on a gold substrate as the pH of the deposition environment is altered. The protonation states of the four --COOH groups of the N3 dye change according to the modified pH conditions, thus affecting the number of --COOH and --NCS functional groups that participate in the adsorption to gold. Here, we use heterodyne detected vibrational sum frequency generation (HD-VSFG) spectroscopy to obtain surface specific vibrational information on both --COOH and --NCS groups as a function of pH of the deposition conditions. Polarization-dependent HD-VSFG yields sets of complex χ (2) spectra, enabling us to perform a simultaneous fitting procedure to the polarization-dependent real and imaginary components and thus extract detailed structural information of the N3/gold interface. Overall, our results show that N3 preferentially adsorbs to gold either with two --COOH groups and one --NCS group in more acidic conditions or with one --COOH group and two --NCS groups in more basic conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Rippled shock propagation in a laser-driven target at multimegabar pressures

The evolution of non-uniform shocks produced by modulated laser irradiation or surface perturbations is relevant to studies of inertial confinement fusion and material properties at high-energy-density conditions. We present results from an experiment conducted at the OMEGA EP laser facility, where a 300 GPa shock was driven into a fused silica sample with pre-fabricated single-mode surface modulations. Using time-resolved optical velocimetry, we captured the continuous evolution of rippled shock motion, enabling a comprehensive mapping of the spatial amplitude history from formation to phase reversal in a single experiment. Initially, the ablation-driven shock inherits a fraction of the surface modulation amplitude from the sample, which subsequently grows before decaying, ultimately leading to the flattening of the rippled shock and a phase reversal. We find that two-dimensional inviscid hydrodynamic simulation of the experiment is able to qualitatively capture many aspects of the rippled shock evolution but over-predicts the initial amplitude growth. This experimental platform, capable of accommodating varying ripple wavelengths, lays the groundwork for a potential viscometry method at extreme pressures, where viscous effects manifest as differences in shock flattening times between rippled shocks of two distinct wavelengths propagating through the sample.

36 MATERIALS SCIENCE↗

DOE OSTI2023

A computational study of how surfaces affect slip family activity

Plastic deformation behavior is most conveniently assessed by characterization on a surface, but whether such observations are representative of bulk properties is uncertain. Motivated by reported inconsistencies in slip resistance probed at different depths, we investigated (i) whether the average slip family activity is affected by the presence of a surface and (ii) how the kinematic nature of available slip families influences a potential surface effect. The slip family activity as a function of distance from the surface was extracted from full-field crystal plasticity simulations of random polycrystalline hexagonal close-packed (HCP) and body-centered cubic (BCC) metals as examples of mixed in contrast to universally-high numbers of slip systems per family. Under certain conditions, a deviation from bulk slip activity is observed up to about two grains from the surface. For the easiest (least slip-resistant) family, a surface effect of decreasing activity with depth emerges if the number of slip systems falls below about six. For harder families, slip activity always increases with depth. Furthermore, these phenomena are explained on the basis of varying constraints with depth in connection with the kinematic properties of slip families in the material.

36 MATERIALS SCIENCE↗

DOE OSTI2023

A physics-driven Σ-Y atomization model for heavy-duty engine simulations

The atomization of a liquid jet is a multi-scale and multi-physics problem of interest for many engineering applications. Particularly, it drives the fuel-oxidizer mixing and dictates the efficiency of combustion engines. High-fidelity multi-phase simulations remain challenging due to the excessive computational cost required to capture all the atomization scales. Thus, atomization models are necessary to represent sub-grid liquid structures. Here, in this work, a modified Σ-Y model in the context of Eulerian-Lagrangian Spray Atomization (ELSA) is used to transport the surface area density of the spray. The model's predictive performance is assessed under various operating conditions relevant to heavy-duty engines using the Engine Combustion Network (ECN) Spray C and Spray D research-grade injectors. The classic droplet collision formulation of the Σ-Y model alone does not replicate the response of the measured spray surface area to changes in injector, ambient pressure, and injection pressure, requiring individual tuning of the model's parameters. Instead, a transition between dense and dilute spray breakup mechanisms is proposed in terms of the average droplet spacing. The collision breakup mechanism represents the dilute spray, whereas the droplet size in the dense spray is driven by a competition between the integral scale of turbulence and the balance between the turbulent kinetic energy and the surface energy of the droplets. Such an approach minimizes the requirements for model tuning. Moreover, the role of the constants of a compressible standard k-ε RANS model is assessed in the injector's internal flow and external spray simulation framework, and an updated set is proposed. The results are validated against x-ray radiography and Ultra-Small Angle X-ray Scattering (USAXS) data and highlight the predictive capabilities of the proposed physics-driven Σ-Y model, which is compatible with engine simulation turnaround times.

42 ENGINEERING↗

DOE OSTI2021

Microbubble dynamics and heat transfer in boiling droplets

Dissipating large heat fluxes from a surface is critically important in numerous industrial and natural applications. Boiling based spray cooling and surface texturing are two of the most promising methods being investigated to address this problem. Although our understanding on these topics has significantly improved over past decades, critical gaps remain in the knowledgebase stymieing the realization of their full potential. As an example, while bubble growth in pool boiling have been investigated in detail, comparatively little is known about how the bubbles evolve inside boiling drops. In the present work, we have investigated for the first time, the microbubble dynamics inside water droplets boiling on superhydrophilic textured substrates using high-speed X-ray phase contrast imaging (XRPCI). Our observations show that the transient bubble density variation follows similar characteristics irrespective of the texture spacing at a given surface temperature. For an example microstructure, we found that the number of discrete bubbles on the surface decreases as temperature is increased although their growth rate increases. Here, we observe that bubble growth is highly non-uniform during the lifetime of a drop on the surface. Initially, bubbles grow under diffusion-limited regime, but at later times they grow as ~t 1.45 due to combined effects of coalescence and evaporation. In some conditions, we found that bubbles shrink dramatically af- ter the initial growth spurt presumably due to severe quenching of the surface, and migration of bubbles on the surface. Using the bubble sizes, for the first time we analyzed the heat flux removed by a single bubble and also by all the bubbles at a given time. We find that the highest dissipation through latent- heat component (~600 W/cm 2 ) occurs just in the beginning and thereafter it decreases. We expect that our findings and the analysis would guide further work on the topic and will aid in the overarching goal of engineering surfaces that are more efficient in boiling heat transfer.

42 ENGINEERING↗

DOE OSTI2021

Small-angle X-ray and neutron scattering

Small-angle scattering (SAS) is a technique that is able to probe the structural organization of matter and quantify its response to changes in external conditions. X-ray and neutron scattering profiles measured from bulk materials or materials deposited at surfaces arise from nanostructural inhomogeneities of electron or nuclear density. Furthermore, the analysis of SAS data from coherent scattering events provides information about the length scale distributions of material components. Samples for SAS studies may be prepared in situ or under near-native conditions and the measurements performed at various temperatures, pressures, flows, shears or stresses, and in a time-resolved fashion. In this Primer, we provide an overview of SAS, summarizing the types of instrument used, approaches for data collection and calibration, available data analysis methods, structural information that can be obtained using the method, and data depositories, standards and formats. Recent applications of SAS in structural biology and the soft-matter and hard-matter sciences are also discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2020

Mesoporous silica-encapsulated gold core–shell nanoparticles for active solvent-free benzyl alcohol oxidation

Silica-encapsulated gold core@shell nanoparticles (Au@SiO2 CSNPs) were synthesized via a bottom-up procedure and used to catalyze the selective oxidation of benzyl alcohol. The pore size, morphology, crystallinity and composition of Au@SiO2 was evaluated using non-local density functional theory, transmission electron microscopy, high-energy x-ray diffraction and inductively coupled plasma-mass spectroscopy, respectively. The nanoparticles exhibit a mesoporous shell with an average thickness of 25.5 Å which can enhance selectivity via preferential transport of the desired product (i.e., benzaldehyde) relative to larger, undesired products (i.e, benzoic acid/benzyl benzoate). GC-FID analysis revealed the addition of potassium carbonate to the solvent-free oxidation of benzyl alcohol increased conversion from 17.3 to 60.4% while decreasing selectivity from 98.7 to 75.0%. Under equivalent conditions, a bare gold nanoparticle control catalyst deposited on a silica support with a similar gold surface area took 6 times as long to reach the same conversion, achieving only 49.4% selectivity. These results suggest that the pore size distribution within the inert silica shell of Au@SiO2 CSNPs inhibits the formation of undesired products to facilitate the selective oxidation of benzaldehyde despite a basic environment, which reduces selectivity under typical conditions. The CSNPs demonstrated a much lower activation energy than the Au-SiO2 control catalyst, 37 ± 1.9 kJ/mol and 72 ± 7.1 kJ/mol, respectively. Thiele modulus analysis indicates the CSNP pore structure does not create a mass transport limitation due to the nano-scale path of diffusion through the pore structure to the active surface. The lower activation energy and mesopore distribution together suggest the Au@SiO2 catalyst demonstrates higher activity through beneficial in-pore orientation, both reducing competitive adsorption and promoting a single, lower activation energy mechanistic pathway.

benzyl alcohol oxidation, catalysis, confinement↗

DOE OSTI2025

Mitigating Crack Formation When Using High Oxygen Permeability Ionomer in PEMFC Catalyst Layers

High oxygen permeability ionomers (HOPIs) are being developed as an alternative to conventional perfluorosulfonic (PFSA) ionomers for cathodes in proton exchange membrane fuel cells (PEMFCs). HOPIs aim to reduce local oxygen transport resistance, improving performance and reducing degradation as the catalyst loses surface area. However, HOPIs' more rigid, 3D backbone leads to increased crack density in the cathode, potentially causing accelerated degradation. This study investigates crack formation in HOPI-based and PFSA-bound catalyst layers (CLs). We conducted a comprehensive parametric study to identify conditions and catalyst slurry components that minimize cracking. CLs were fabricated with various ionomer and catalyst types, under different relative humidity (RH) levels, solids weight percentages, solvent ratios, and ionomer-to-carbon ratios (I/C). Results show that HOPI-based CLs exhibit less cracking when fabricated under low RH conditions, with lower solids weight percentage, higher alcohol content, and lower I/C. Additionally, catalysts with low/medium surface area carbon supports show less cracking than those with high surface area carbon supports.

08 HYDROGEN↗