Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

Microstructural characterization of in situ MXCT images of high density foams under large strains

Foams are used in numerous applications, such as vibration damping and energy mitigation (e.g., packaging and helmets), wherein their mechanical properties are of critical importance. A typical compressive response of a high density elastomeric foam, shown in Fig 1, generally contains three regions of interest: (I) a linear-elastic region, governed by strut bending; (II) a relatively flat, or slowly increasing stress-strain response, accompanied by strut buckling and the localized collapse of pores; and (III) an exponentially increasing stress-strain curve wherein the collapse of the pore matrix leads to densification. Two material properties of interest, upon which considerable research has focused are the foam's Young's modulus, E{sub f}, defined as the slope of the stress-strain response in region I, and the collapse stress, {sigma}{sub f}, defined as the stress at which the response begins to deviate from linearity. It has been observed [1, 2, 3] that Young's modulus and the collapse stress are dependent on the material properties of the strut material and the non-dimensional relative-density of the foam, {rho}* = {rho}{sub f}/{rho}{sub m}, where {rho}{sub r} is the gross density of the foam and {rho}{sub m} is the density of the strut, or matrix, material. For foam of low relative-density, i.e, {rho}* < 0.1, the collapse stress and Young's modulus obey the relations {sigma}{sub c}/E{sub m} {proportional_to} ({rho}*){sup m} and E{sub f}/E{sub m} {proportional_to} ({rho}*){sup n} where E{sub m} is Young's modulus of the strut material and the bounds on the parameters m and n are 0.05 {le} m {le} 0.2 and 1 {le} n {le} 4 [4]. For open-celled foams, n = 2, whereas for closed-celled foams, n = 3. Theoretically, n = 1 for foams with an ''ideal strut'' configuration [6]. Foams of high relative-density ({rho}* > 0.1) require correcting terms to account for the axial contributions of the ''thick'' struts [5]. The above equations relate important foam properties to the relative-density of the foam; however, there exists a gap in the understanding of how the foam microstructure affects the mechanical response of the foam. This is due in large part to the difficulty of characterizing foam structures in 3D, especially foams of high relative-density. Most elastomeric foams are manufactured by the introduction of a gas into a cross-linking polymer. The developing foam microstructure has a complex dependence on the polymer viscosity and rate of polymerization, resulting in a randomly arranged pore structure with a large distribution of pore sizes. One approach is to characterize foam microstructures solely in terms of the cross-sectional shape and vector arrangement of the strut matrix, since it is this matrix that supports the stresses upon loading of the foam; yet as the density of a foam is increased, the very definition of what constitutes a strut brakes down. Another, perhaps easier to visualize, characterization of foam microstructure can come from a description of the pore shape and arrangement. Given the random nature of the microstructures of blown foam, both approaches are useful and valid. This paper describes our work aimed at linking the mechanical response and microstructural evolution of high relative-density foam as it undergoes large deformation. This work consists of several inter-related parts, including (i) measuring the compressive stress-strain response, as illustrated in Fig. 1, (ii) obtaining in situ micro X-ray computed tomography (MXCT) images of high relative-density foams undergoing large strains, and (iii) developing mathematical, computer aided, methodologies to perform image analysis and calculations of parameters that characterize the pores and struts. By using MXCT, a non-invasive technique for imaging the internal structure of materials, we are able to observe, internally, individual struts and pores as they undergo large deformation. Here we describe our computer aided image analysis methodologies and present examples of their application to the MXCT images of foams. Operations of the computer program include noise removal (smoothing), thresholding [7], edge detection [8], distance transformation [9, 10], pore detection via a Hough transformation [11], and skeletonization [12]. Strut parameters, such as the strut cross-sectional area and strut arrangement, are calculated from a skeleton-based model of the MXCT images. The Hough transform is a feature detection method used primarily in image analysis applications. We use this transform to detect and calculate pore parameters, such as pore arrangement and pore size distribution. The experiments and calculations are performed in order to develop data for the formulation of theory that links foam mechanical behavior specifically to the microstructure of high relative-density foams, not just simply to the relative-density of the foam.

36 MATERIALS SCIENCE↗

“Lattice Strain Matching”‐Enabled Nanocomposite Design to Harness the Exceptional Mechanical Properties of Nanomaterials in Bulk Forms

Abstract Nanosized materials are known to have the ability to withstand ultralarge elastic strains (4–10%) and to have ultrahigh strengths approaching their theoretical limits. However, it is a long‐standing challenge to harnessing their exceptional intrinsic mechanical properties in bulk forms. This is commonly known as “the valley of death” in nanocomposite design. In 2013, a breakthrough was made to overcome this challenge by using a martensitic phase transforming matrix to create a composite in which ultralarge elastic lattice strains up to 6.7% are achieved in Nb nanoribbons embedded in it. This breakthrough was enabled by a novel concept of phase transformation assisted lattice strain matching between the uniform ultralarge elastic strains (4–10%) of nanomaterials and the uniform crystallographic lattice distortion strains (4–10%) of the martensitic phase transformation of the matrix. This novel concept has opened new opportunities for developing materials of exceptional mechanical properties or enhanced functional properties that are not possible before. The work in progress in this research over the past six years is reported.

Zhang, Junsong↗

Comprehensive Electrical Control of Metamagnetic Transition of a Quasi-2D Antiferromagnet by In Situ Anisotropic Strain

Effective nonmagnetic control of the spin structure is at the forefront of the study for functional quantum materials. This study demonstrates that, by applying an anisotropic strain up to only 0.05%, the metamagnetic transition field of spin–orbit-coupled Mott insulator Sr 2 IrO 4 can be in situ modulated by almost 300%. Simultaneous measurements of resonant X-ray scattering and transport reveal that this drastic response originates from the complete strain-tuning of the transition between the spin-flop and spin-flip limits, and is always accompanied by large elastoconductance and magnetoconductance. This enables electrically controllable and electronically detectable metamagnetic switching, despite the antiferromagnetic insulating state. The obtained strain-magnetic field phase diagram reveals that C 4 -symmetry-breaking anisotropy is introduced by strain via pseudospin-lattice coupling, directly demonstrating the pseudo-Jahn–Teller effect of spin–orbit-coupled complex oxides. The extracted coupling strength is much weaker than the superexchange interactions, yet crucial for the spontaneous symmetry-breaking, affording the remarkably efficient strain-control.

36 MATERIALS SCIENCE↗

Conversion of Classical Light Emission from a Nanoparticle‐Strained WSe 2 Monolayer into Quantum Light Emission via Electron Beam Irradiation

Abstract Solid‐state single photon emitters (SPEs) within atomically thin transition metal dichalcogenides (TMDs) have recently attracted interest as scalable quantum light sources for quantum photonic technologies. Among TMDs, WSe 2 monolayers (MLs) are promising for the deterministic fabrication and engineering of SPEs using local strain fields. The ability to reliably produce isolatable SPEs in WSe 2 is currently impeded by the presence of numerous spectrally overlapping states that occur at strained locations. Here nanoparticle (NP) arrays with precisely defined positions and sizes are employed to deterministically create strain fields in WSe 2 MLs, thus enabling the systematic investigation and control of SPE formation. Using this platform, electron beam irradiation at NP‐strained locations transforms spectrally overlapped sub‐bandgap emission states into isolatable, anti‐bunched quantum emitters. The dependence of the emission spectra of WSe 2 MLs as a function of strain magnitude and exposure time to electron beam irradiation is quantified and provides insight into the mechanism for SPE production. Excitons selectively funnel through strongly coupled sub‐bandgap states introduced by electron beam irradiation, which suppresses spectrally overlapping emission pathways and leads to measurable anti‐bunched behavior. The findings provide a strategy to generate isolatable SPEs in 2D materials with a well‐defined energy range.

2D material↗

Probing and Tuning Strain‐Localized Exciton Emission in 2D Material Bubbles at Room Temperature

In monolayer transition metal dichalcogenides bubbles-nanoscale deformations typically exhibiting a dome-like shape-Excitons are confined by the strain effect, which exhibits extraordinary emission properties, such as single photon generation, enhanced light emission, and spectrally tunable excitonic states. While the strain profiles of these bubbles are extensively studied, this work provides an approach 1) to directly visualize the associated exciton properties in bubbles formed in WSe2 monolayer, revealing an intrinsic emission wavelength shift of ≈40 nm, and 2) actively modify local strain, enabling further exciton emission tuning over a range of 50 nm. These are achieved by emission mapping and nanoindentation using a dielectric near-field probe, which enables the detection of local emission spectra and emission lifetimes within individual bubbles. Statistical analysis of 67 bubbles uncovers an emission wavelength distribution centered around 780 nm. Furthermore, saturation behavior in the power-dependent studies and the associated lifetime change reveal the localized nature of the strain-induced states. These findings provide direct insights into the strain-localized emission dynamics in bubbles and establish a robust framework for non-destructive, reversible, and predictable nanoscale emission control, presenting a potential avenue for developing next-generation tunable quantum optical sources.

2D materials bubbles↗

Reducing the Strain Required for Ambient‐Pressure Superconductivity in Ruddlesden‐Popper Bilayer Nickelates

ABSTRACT The discovery of high‐temperature superconductivity in pressurized bulk Ruddlesden‐Popper (RP) bilayer nickelates has prompted the conjecture that epitaxial compressive strain might mimic essential aspects of hydrostatic pressure. The realization of superconductivity in films on SrLaAlO 4 (001) (SLAO) supports this correspondence, yet it remains unclear whether the pressure–temperature phase diagram of RP bilayer nickelates can be systematically mapped (and studied at ambient pressure) as a function of epitaxial strain. To this end, experimental access near the elusive edge of the superconducting phase boundary would provide invaluable insight into the nature of the superconducting state and the ground state from which it emerges. Here we report superconducting RP bilayer nickelates grown on LaAlO 3 (001) (LAO), where the compressive strain required for ambient‐pressure superconductivity is nearly halved to −1.2%. These films exhibit a superconducting onset above 10 K and reach zero resistance at 3 K, with normal‐state transport properties differing from those of films grown on SLAO. Our comparative study shows that strain–rather than interfacial structure is the primary factor governing the superconductivity and normal‐state properties. This work offers a new opportunity to probe emergent phenomena near the superconducting phase boundary in the strain–temperature phase diagram of RP bilayer nickelates.

Tarn, Yaoju [Department of Applied Physics Stanfor↗

Bioprocessing analysis of Pyrococcus furiosus strains engineered for CO 2 -based 3-hydroxypropionate production

In this paper, metabolically engineered strains of the hyperthermophile Pyrococcus furiosus (T opt 95–100°C), designed to produce 3-hydroxypropionate (3HP) from maltose and CO 2 using enzymes from the Metallosphaera sedula (T opt 73°C) carbon fixation cycle, were examined with respect to the impact of heterologous gene expression on metabolic activity, fitness at optimal and sub-optimal temperatures, gas-liquid mass transfer in gas-intensive bioreactors, and potential bottlenecks arising from product formation. Transcriptomic comparisons of wild-type P. furiosus , a genetically-tractable, naturally-competent mutant (COM1), and COM1-based strains engineered for 3HP production revealed numerous differences after being shifted from 95°C to 72°C, where product formation catalyzed by the heterologously-produced M. sedula enzymes occurred. At 72°C, significantly higher levels of metabolic activity and a stress response were evident in 3HP-forming strains compared to the non-producing parent strain (COM1). Gas–liquid mass transfer limitations were apparent, given that 3HP titers and volumetric productivity in stirred bioreactors could be increased over 10-fold by increased agitation and higher CO 2 sparging rates, from 18 mg/L to 276 mg/L and from 0.7 mg/L/h to 11 mg/L/h, respectively. 3HP formation triggered transcription of genes for protein stabilization and turnover, RNA degradation, and reactive oxygen species detoxification. Lastly, the results here support the prospects of using thermally diverse sources of pathways and enzymes in metabolically engineered strains designed for product formation at sub-optimal growth temperatures.

3-hydroxypropionate↗

Engineered CRISPR/Cas9 system for multiplex genome engineering of polyploid industrial yeast strains

The CRISPR/Cas9 system has been widely used for multiplex genome engineering of Saccharomyces cerevisiae . Furthermore, its application in manipulating industrial yeast strains is less successful, probably due to the genome complexity and low copy numbers of gRNA expression plasmids. Here we developed an efficient CRISPR/Cas9 system for industrial yeast strain engineering by using our previously engineered plasmids with increased copy numbers. Four genes in both a diploid strain (Ethanol Red, 8 alleles in total) and a triploid strain (ATCC 4124, 12 alleles in total) were knocked out in a single step with 100% efficiency. This system was used to construct xylose-fermenting, lactate-producing industrial yeast strains, in which ALD6, PHO13, LEU2, and URA3 were disrupted in a single step followed by the introduction of a xylose utilization pathway and a lactate biosynthetic pathway on auxotrophic marker plasmids. The optimized CRISPR/Cas9 system provides a powerful tool for the development of industrial yeast based microbial cell factories.

59 BASIC BIOLOGICAL SCIENCES↗

Strain Recovery and Defect Characterization in Mg‐Implanted Homoepitaxial GaN on High‐Quality GaN Substrates

The evolution of defects due to high‐pressure annealing of magnesium ion‐implanted epitaxial GaN grown on high‐quality GaN substrates is investigated. Changes in the implant‐induced strain are quantified as a function of annealing temperature and time. After annealing at 1300 °C for 10 min, the implant‐induced strain is fully relieved and accompanied by the presence of extended defects such as basal plane stacking faults and prismatic loops. Approximately one‐third of the original implant‐induced strain remains after annealing at 700 °C, and 5% of the original strain remains at 1000 °C for 100 min. In all cases, nearly all of the recovered strain occurs within first few minutes of annealing. A prominent increase in the asymmetric (104) triple axis X‐ray rocking curve full width at 0.01 maximum (FW0.01M) is observed after annealing at 1300 °C for 10 min. After annealing at 1300 °C for 100 min, a subsequent decrease in FW0.01M is correlated with a reduction of the extended defect density from 4 × 10 8 to 3 × 10 7 cm −2 , determined through transmission electron microscope (TEM) measurements. Further reduction in the density of the extended defects by optimizing annealing temperature and time is expected to improve the performance of GaN‐based vertical power devices.

Wang, Yekan↗

Field validation of dynamic mechanical torque measurements using fiber-optic strain sensors for geared wind turbines

Abstract Accurate knowledge of the mechanical loads of wind turbine gearboxes has become essential in modern, highly loaded gearbox designs, as maintaining or even improving gearbox reliability with increasing torque density demands is proving to be challenging. Unfortunately, the traditional method of measuring dynamic mechanical torque using strain gauges placed on the outer surface of a rotating shaft and transmitting the resulting signal is unsuitable for serial deployment due to technical and economic constraints. An alternative method based on fiber-optic strain sensors placed on the stationary outer surface of the gearbox ring gear has been proposed. Like shaft torsion, the radial deformation of the ring gear is proportionate to the rotor torque. Placing the sensors on a stationary component is a cost-effective alternative for serial implementation because the need for complex and expensive data transfer via wireless transmission or a slip ring is eliminated. In this paper, we present the results of an extensive field experiment conducted to evaluate the torque measurement accuracy of this novel sensing solution installed on the gearbox of a Gamesa G97 2-MW wind turbine at the National Renewable Energy Laboratory’s Flatirons Campus. Torque measurements derived from fiber-optic strain sensors placed on the ring gear of the planetary stage are compared to conventional torque measurements from strain gauges placed on the main shaft. Two different torque estimation data processing methods were evaluated, with the method based on operational deflection shapes providing the most accurate results with an average normalized root mean square error below 0.7% for a load revolution distribution analysis. The effect of operating conditions on the torque estimate was also investigated, and the third planet-passing operational deflection shape was found to be the least sensitive to nontorque load-related effects. The fiber-optic strain sensors’ successful operation during the complete test campaign has demonstrated a robust and accurate solution for fleet-wide enhanced gearbox remaining useful life estimation.

17 WIND ENERGY↗

Influence of Carbon Sources and Electron Shuttles on Ferric Iron Reduction by Cellulomonas sp. Strain ES6

Microbially reduced iron minerals can reductively transform a variety of contaminants including heavy metals, radionuclides, chlorinated aliphatics, and nitroaromatics. A number of Cellulomonas spp. strains, including strain ES6, isolated from aquifer samples obtained at the U.S. Department of Energy's Hanford site in Washington, have been shown to be capable of reducing Cr(VI), TNT, natural organic matter, and soluble ferric iron [Fe(III)]. This research investigated the ability of Cellulomonas sp. strain ES6 to reduce solid phase and dissolved Fe(III) utilizing different carbon sources and various electron shuttling compounds. Results suggest that Fe(III) reduction by and growth of strain ES6 was dependent upon the type of electron donor, the form of iron present, and the presence of synthetic or natural organic matter, such as anthraquinone-2,6-disulfonate (AQDS) or humic substances. This research suggests that Cellulomonas sp. strain ES6 could play a significant role in metal reduction in the Hanford subsurface and that the choice of carbon source and organic matter addition can allow for independent control of growth and iron reduction activity.

54 ENVIRONMENTAL SCIENCES↗

Revisiting the first Sandia Fracture Challenge with transient deformation heating and strain localization considerations

In this study, we present a systematic experimental study and accompanying theoretical analysis of the dependence of ductile fracture on strain localization, strain hardening rates, deformation-induced thermal softening, and transient heat conduction under spatially uniform as well as spatially heterogeneous deformation. Spatially uniform cases are studied via standard dogbone shaped specimens subject to uniaxial tension. Spatially heterogeneous deformation is studied via the so-called Sandia Fracture Challenge (SFC) specimen, which is a standard compact tension specimen modified with three machined holes in front of a blunt notch. We utilize the same precipitation hardened martensitic stainless steel used in the first SFC experiments, i.e. 15-5 PH with an H1075 heat treatment. We also study 15-5 PH in Condition A and with the H900 heat treatment, each of which has a different hardening behavior and ductility. We find that the ductility does not correlate with the deformation to first crack initiation in the SFC specimen. Instead, hardening rates are better correlated. Moreover, a re-examination finds that an accurate calibration of the hardening rates is strongly correlated with accurate blind predictions of ductile fracture in the SFC specimens. Given that thermal softening can greatly affect hardening rates, we provided a thermographic analysis of deformation-induced heating and transient heat transfer in both the dogbone shaped samples and the SFC specimens. Transient heating in stainless steels is found to have first-order effects on the strain at the onset of necking, strain to fracture, as well as strain localization and ductile fracture in complex geometries even under so-called quasi-static loading rates.

42 ENGINEERING↗

An Internal Digital Image Correlation Technique for High-Strain Rate Dynamic Experiments

Full-field, quantitative visualization techniques, such as digital image correlation (DIC), have unlocked vast opportunities for experimental mechanics. However, DIC has traditionally been a surface measurement technique, and has not been extended to perform measurements on the interior of specimens for dynamic, full-scale laboratory experiments. This limitation restricts the scope of physics which can be investigated through DIC measurements, especially in the context of heterogeneous materials. The focus of this study is to develop a method for performing internal DIC measurements in dynamic experiments. The aim is to demonstrate its feasibility and accuracy across a range of stresses (up to 650 MPa), strain rates (10 3 - 10 6 s -1 ), and high-strain rate loading conditions (e.g., ramped and shock wave loading). Internal DIC is developed based on the concept of applying a speckle pattern at an inner-plane of a transparent specimen. The high-speed imaging configuration is coupled to the traditional dynamic experimental setups, and is focused on the internal speckle pattern. During the experiment, while the sample deforms dynamically, in-plane, two-dimensional deformations are measured via correlation of the internal speckle pattern. In this study, the viability and accuracy of the internal DIC technique is demonstrated for split-Hopkinson (Kolsky) pressure bar (SHPB) and plate impact experiments. The internal DIC experimental technique is successfully demonstrated in both the SHPB and plate impact experiments. In the SHPB setting, the accuracy of the technique is excellent throughout the deformation regime, with measurement noise of approximately 0.2% strain. In the case of plate impact experiments, the technique performs well, with error and measurement noise of 1% strain. The internal DIC technique has been developed and demonstrated to work well for full-scale dynamic high-strain rate and shock laboratory experiments, and the accuracy is quantified. Here, the technique can aid in investigating the physics and mechanics of the dynamic behavior of materials, including local deformation fields around dynamically loaded material heterogeneities.

36 MATERIALS SCIENCE↗

Insights from the Lattice-Strain Evolution on Deformation Mechanisms in Metallic-Glass-Matrix Composites

In this paper, in situ high-energy synchrotron X-ray diffraction experiments and micromechanics-based finite element simulations have been conducted to examine the lattice-strain evolution in metallic-glass-matrix composites (MGMCs) with dendritic crystalline phases dispersed in the metallic-glass matrix. Significant plastic deformation can be observed prior to failure from the macroscopic stress–strain curves in these MGMCs. The entire lattice-strain evolution curves can be divided into elastic–elastic (denoting deformation behavior of matrix and inclusion, respectively), elastic–plastic, and plastic–plastic stages. Characteristics of these three stages are governed by the constitutive laws of the two phases (modeled by free-volume theory and crystal plasticity) and geometric information (crystalline phase morphology and distribution). The load-partitioning mechanisms have been revealed among various crystalline orientations and between the two phases, as determined by slip strain fields in crystalline phase and by strain localizations in matrix. Finally, implications on ductility enhancement of MGMCs are also discussed.

36 MATERIALS SCIENCE↗

Identifying Deformation and Strain Hardening Behaviors of Nanoscale Metallic Multilayers Through Nano-wear Testing

In complex loading conditions (e.g. sliding contact), mechanical properties, such as strain hardening and initial hardness, will dictate the long-term performance of materials systems. With this in mind, the strain hardening behaviors of Cu/Nb nanoscale metallic multilayer systems were examined by performing nanoindentation tests within nanoscratch wear boxes and undeformed, as-deposited regions. Both the architecture and substrate influence were examined by utilizing three different individual layer thicknesses (2, 20, and 100 nm) and two total film thicknesses (1 and 10 μm). After nano-wear deformation, multilayer systems with thinner layers showed less volume loss as measured by laser scanning microscopy. Additionally, the hardness of the deformed regions significantly rose with respect to the as-deposited measurements, which further increased with greater wear loads. Strain hardening exponents for multilayers with thinner layers (2 and 20 nm, n ≈ 0.018 and n ≈ 0.022 respectively) were less than was determined for 100 nm systems (n ≈ 0.041). These results suggest that singledislocation based deformation mechanisms observed for the thinner systems limit the extent of achievable strain hardening. This conclusion indicates that impacts of both architecture strengthening and strain hardening must be considered to accurately predict multilayer performance during sliding contact across varying length scales.

36 MATERIALS SCIENCE↗

Microstructure and residual elastic strain at graphite nodules in ductile cast iron analyzed by synchrotron X-ray microdiffraction

The microstructure and residual elastic strain at graphite nodules (GNs) in ductile cast iron produced using either a fast or slow cooling rate have been characterized using synchrotron 3D X-ray Laue microdiffraction. The results demonstrate that thermal stress is introduced during cooling and that part of this stress is relaxed by plastic deformation of the polycrystalline ferrite matrix. It is observed that the plastic deformation is accommodated by the formation of dislocations and dislocation boundaries, which are organized in a cell structure. The dislocation density quantified based on the microstructure is most pronounced at the GN/matrix interface around small GNs in the fast cooled sample. Residual elastic strain is also present, which is mainly compressive with a maximum of 6.0–9.9 &times; 10 -4 near the GNs. Gradients of plastic deformation and elastic strain field around the GNs are observed. The results document for the first time that both the elastic strain field and the plastic strain field averaged over the grains around the GNs is approximately scaling with GN size and not affected by the cooling rate. The experimental data are compared with simulations by a finite element method, and agreement and disagreement are considered in detail.

36 MATERIALS SCIENCE↗

The influence of cooling rates on strain phase diagrams and domain structures of ferroelectric thin films: A case study of PbTiO 3

Strain engineering has been established as an effective approach to control phase equilibria, domain configurations, and functional properties of ferroelectric thin films. Temperature-strain phase diagrams have been used as powerful tools for providing insights into strain engineering. However, almost all existing phase diagrams established using the phase-field approach assume quenching conditions without considering actual cooling rates during the post-deposition annealing process of ferroelectric thin films. Within this work, we systematically investigate the influence of cooling rates on domain structures and the strain-phase diagram of ferroelectric thin films using phase-field simulations, taking PbTiO 3 thin films as a model system. We found that both the position of phase boundaries in the strain phase diagrams and the domain morphology are significantly influenced by the cooling rates. It is revealed that while the paraelectric-ferroelectric phase boundary remains invariant, the phase boundaries between single-phase and multi-phase regions tend to shift toward the corresponding multi-phase region as the cool rate reduces. Slow cooling generally leads to more ordered domain structures with increased domain size. Using the obtained equilibrium domain structures, we calculated effective thermal conductivities and found significant variations that can be tuned by the cooling rates. In conclusion, this work reveals an underexplored yet critical impact of cooling rates on phase equilibria and domain structures in ferroelectric thin films, which may inspire further fine-tuning of domains and domain walls in low-dimensional ferroelectrics for multifunctional applications.

Domain structures↗

Ultrastructure of the green alga Dunaliella salina strain CCAP19/18 (Chlorophyta) as investigated by quick-freeze deep-etch electron microscopy

The single-celled green alga Dunaliella salina is a model system for studies on stress biology, in particular regarding secondary carotenoid accumulation. Under non-stress conditions the cells are green, but under abiotic stress the cells turn orange, because they switch their metabolism and accumulate β-Carotene in globules in the chloroplast. For the first time, Quick-freeze deep-etch electron microscopy was used to visualize cellular structures in green and orange cells of D. salina strain CCAP19/18. This allowed us to present an in-depth analysis of the cellular ultrastructure describing and comparing the features of the two cell types. Our images illustrate the presence of a pericellular matrix for this strain of D. salina. The pericellular matrix was spongy and strands of unknown material anchored it into the plasma membrane. The cytoplasm contained a variety of vesicles, vacuoles, and acidocalcisomes. We could show for strain CCAP19/18 that cytoplasmic lipid bodies were often in close proximity to and sometimes in contact with the outer chloroplast envelope membrane and with the endoplasmic reticulum. Major visible differences between green and orange cells were in the chloroplast: the orange cells have greatly reduced amounts of thylakoid membranes and greatly increased numbers of β-Carotene globules. We showed that the β-Carotene globules often made point contacts with thylakoid membranes, and frequently laid side-by-side along the thylakoid membrane surface, providing support to studies that indicated exchange of molecules between β-Carotene globules and thylakoid membranes. A unique finding was the β-Carotene globule duplets, suggesting intermediate stages in β-Carotene globule morphogenesis. Overall, the β-Carotene globules appear to be similar to plant plastoglobuli. We provide this description of the cellular ultrastructure features as a resource in the context of the recent publication of the genome of D. salina strain CCAP19/18 to expand on the knowledge regarding this novel reference strain.

59 BASIC BIOLOGICAL SCIENCES↗