Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Electrical and dielectric properties of ZnO and CeO{sub 2} doped ZrTi{sub 2}O{sub 6} ceramic

Zirconium oxide (ZrO{sub 2}) and titanium dioxide (TiO{sub 2}) are the important catalyst supports, since it has acidic and basic properties. The intermediate phase zirconium titanate ZrTi{sub 2}O{sub 6}, which is a solid solution with Zr:Ti ratio 1:2 has outstanding dielectric properties. The effects of doping of ZnO and CeO{sub 2} on the dielectric and electrical properties of ZrTi{sub 2}O{sub 6} ceramic are investigated. On adding 0.5 wt% ZnO, the dielectric constant is increased but, on adding CeO{sub 2}, the dielectric constant is decreased. The bulk density of pure sample sintered at 1530 °C is 91% of theoretical density while that of the doped samples sintered at 1450 °C is more than 94% of theoretical density. Scanning electron micrographs reveal that the samples are well sintered with minimum porosity. The semicircle behavior in the Cole-Cole plots at room temperature reveals that the samples are good ionic conductor. The induced impedance is reduced for doped samples and this can be used as a material for electrolyte in Solid Oxide Fuel Cell.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Low temperature dielectric and impedance studies on magnetoelectric Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3} ceramic

The structural, microstructural, low temperature dielectric and impedance properties of Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3} (PFN) ceramic prepared by single step solid-state reaction method have been investigated. Processing parameters such as calcination, sintering temperature and sintering durations were optimized to get better dielectric properties. It was found that the above ceramics sintered at 1050 °C for 4 hr exhibited single phase, maximum density and uniform microstructure. X-ray diffraction (XRD) and neutron diffraction (ND) reveals that the system exhibit single phase without any kind of secondary phases at room temperature (RT) with monoclinic crystal structure (Cm). Surface morphology of the compounds was studied by Scanning electron microscope (SEM). Impedance spectroscopy is used to study the electrical behaviour of PFN in the frequency range from 100Hz to 1MHz and in the temperature range from 120 to 293 K. The frequency-dependent electrical data are analyzed by impedance formalisms. The complex impedance shows the relaxation (conduction) mechanism in the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Microwave dielectric properties of CaCu{sub 3}Ti{sub 4}O{sub 12}-Al{sub 2}O{sub 3} composite

(1-x)CaCu{sub 3}Ti{sub 4}O{sub 12} + (x)Al{sub 2}O{sub 3} composite (0 ≤ x ≤0.25) was prepared via conventional solid-state reaction method. The fabrication of sample was started with synthesizing stoichiometric CCTO from CaCO{sub 3}, CuO and TiO{sub 2} powders, then wet-mixed in deionized water for 24 h. The process was continued with calcined CCTO powder at 900 °C for 12 h before sintered at 1040 °C for 10 h. Next, the calcined CCTO powder with different amount of Al{sub 2}O{sub 3} were mixed for 24 h, then palletized and sintered at 1040 °C for 10. X-ray diffraction analysis on the sintered samples showed that CCTO powder was in a single phase, meanwhile the trace of secondary peaks which belong to CaAl{sub 2}O{sub 4} and Corundum (Al{sub 2}O{sub 3}) could be observed in the other samples Scanning electron microscopy analysis showed that the grain size of the sample is firstly increased with addition of Al{sub 2}O{sub 3} (x = 0.01), then become smaller with the x > 0.01. Microwave dielectric properties showed that the addition of Al{sub 2}O{sub 3} (x = 0.01) was remarkably reduced the dielectric loss while slightly increased the dielectric permittivity. However, further addition of Al{sub 2}O{sub 3} was reduced both dielectric loss and permittivity at least for an order of magnitude.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Interface instabilities in hafnium hydride entrained iron metal matrix composites

The chemical interactions in Fe–HfH 2 metal matrix composites (MMCs) are studied across multiple length scales to elucidate the decomposition of the parent phases and corresponding reaction zone physics during direct current sintering. Fe–HfH 2 composites were synthesized with increasing as-mixed hydride contents of Fe–25% HfH 2 , Fe–40% HfH 2 , Fe–55% HfH 2 , and Fe–70% HfH 2 (all in vol. %) to demonstrate the ability to achieve sintered MMCs with target hydride contents. Samples were probed across multiple length scales through a multi-modal workflow employing x-ray diffraction, scanning electron microscopy and segmentation analysis, and synchrotron techniques including hard x-ray fluorescence mapping and nanoprobe x-ray absorption near-edge structure measurements. Under the selected sintering temperature and pressure conditions, hydrogen evolution is seen to evolve through parallel paths: thermal decomposition from during the transformation of HfH 2 to HfH x<2 and through subsequent reaction with the Fe matrix leading to intermetallic phase formation. Specifically, HfFe and HfFe 2 intermetallic formation accelerates the release of hydrogen with a subsequent HfO 2 phase forming at grain boundaries. For this MMC, the consumption or loss of hydrogen can be considerable in compacts with initial hydride loading of 25%–40% HfH 2 approaching 83% hydrogen loss for the lower volume fraction composites. Increasing the volume fraction of HfH 2 to 70% enhanced the retained hydrogen content to 53% and attributed to the reduced interfacial area intrinsic to the increased HfH 2 loading in this MMC.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive manufacturing of multiscale NiFeMn multi-principal element alloys with tailored composition

Nanostructured multi-principal element alloys (MPEAs) have been explored as next-generation engineering materials due to unique mechanical and functional properties which have significant advantages over traditional dilute alloys. However, the practical applications of nanostructured MPEAs are still limited due to the lack of scalable processing approaches to prepare a large quantity of nanostructured MPEAs, as well as lack of an efficient pathway for high-throughput discovery of better functional nanostructured MPEAs within their vast compositional space. Here we tackle these challenges by presenting an integrated approach by combining direct-ink-writing-based additive manufacturing, solid-state sintering, and chemical dealloying to manufacture hierarchically porous MPEAs. The hierarchical structure is comprised of macro- and micro-scale pores introduced via extrusion printing and polymer decomposition during sintering, as well as nanoscale pores formed via chemical dealloying. The macro- and micro-scale pores allow efficient dealloying of a large mass of material as the diffusion length that the corroding medium must penetrate remains at the scale of the ligaments formed after sintering (∼10 μm), despite the large volume of the 3D-printed samples. In addition, this integrated approach enables versatile control of the alloy composition via precisely tuning the ratio of elemental powders in the starting ink, thus offering a pathway for high-throughput discovery of novel functional MPEAs. As a case study, multiscale macro/micro/nanoporous NiFeMn MPEAs with three different compositions were investigated as catalysts to reduce the overpotential of oxygen evolution reaction (OER), where NiFeMn-based electrocatalysts display composition-dependent performance such that the overpotential measured at a current of 0.5 A g −1 for OER increases in the order of Ni 58 Fe 29 Mn 13 ⩽ Ni 64 Fe 26 Mn 10 < Ni 76 Fe 18 Mn 6 . This introduced manufacturing process offers new opportunities for scalable fabrication and rapid screening of nanostructured multi-component complex alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Machinable, high‐conductivity NaSICON through mitigation of humidity effects during solid‐state synthesis

The Na + super ion conductor (NaSICON, Na 1+x Zr 2 Si x P 3-x O 12 ) is a solid electrolyte well-known for fast, selective Na + transport at low temperatures, uniquely enabling sodium-based batteries. Producing high-quality NaSICON from solid-state methods, especially when cost-effective, potentially hygroscopic precursors are used, is not trivial. To understand and eliminate the influence of humidity during processing, a scheme was developed to reproducibly yield a high Na + conductivity (3.75 mS/cm at 25°C, 81.7 mS/cm at 150°C), high density (97%), and machinable NaSICON without the use of binders, sintering aids, or dopants. Controlled humidity studies over 20%–50% RH coupled with thermal, structural, and electrical analysis reveal that calcination temperatures < 1000°C leave NaSICON processing susceptible to water absorption at > 20% RH due to the presence of hygroscopic Na 3 PO 4 and Na 2 CO 3 during shaping, pressing, and sintering. Water absorption results in NaSICON with lower densities, machinability, and Na+ conductivity, due to impaired intergranular Na+ transport. At the other extreme, fully converting precursor to the NaSICON phase at 1230°C before pressing and sintering leads to poor conductivity and density. By calcining at 1000°C, excellent quality NaSICON may be produced under a range of laboratory environments, enabling low-cost production of high-conductivity, machinable NaSICON necessary the ever-growing energy storage market.

NaSICON↗
DOE OSTI2014

Determine Minimum Silver Flake Addition to GCM for Iodine Loaded AgZ

The minimum amount of silver flake required to prevent loss of I{sub 2} during sintering in air for a SNL Glass Composite Material (GCM) Waste Form containing AgI-MOR (ORNL, 8.7 wt%) was determined to be 1.1 wt% Ag. The final GCM composition prior to sintering was 20 wt% AgI-MOR, 1.1 wt% Ag, and 80 wt% Bi-Si oxide glass. The amount of silver flake needed to suppress iodine loss was determined using thermo gravimetric analysis with mass spectroscopic off-gas analysis. These studies found that the ratio of silver to AgI-MOR required is lower in the presence of the glass than without it. Therefore an additional benefit of the GCM is that it serves to inhibit some iodine loss during processing. Alternatively, heating the AgI-MOR in inert atmosphere instead of air allowed for densified GCM formation without I{sub 2} loss, and no necessity for the addition of Ag. The cause of this behavior is found to be related to the oxidation of the metallic Ag to Ag{sup +} when heated to above ~300{degrees}C in air. Heating rate, iodine loading levels and atmosphere are the important variables that determine AgI migration and results suggest that AgI may be completely incorporated into the mordenite structure by the 550{degrees}C sintering temperature.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2015

Complete Initial Scoping Tests on the Incorporation of Novel Loaded Iodine Getters into GCM

This study encompasses initial scoping tests on the incorporation of a novel iodine loaded getter material into the Sandia developed low temperature sintering glass ceramic material (GCM) waste form. In particular, we studied the PNNL Ag-I-Aerogel. Optical microscopy indicates inhomogenous samples based on particle sizes and variations in color (AgI vs Ag/AgO on silica). TGA/MS data when heated in air indicates loss of iodine and organics (CO2) between 250-450°C a total of ~15wt% loss, with additional / small iodine loss when during 550°C hold for 1 hr. TGA/MS data when heated in N2 indicates less organic and slightly less iodine loss below 550°C, with no loss of iodine in 550°C 1 hour hold. Furthermore, a substantial mass loss of sulfur containing compounds is observed (m/e of 34 and 36) between 150 – 550°C in both air and N2 sintering atmospheres. In an effort to capture iodine lost to volatilization during heating (at temps below glass sintering temperature of 550°C), we added 5 wt% Ag flake to the AgIaerogel. Resulting data indicates the iodine is retained with the addition of the Ag flake, resulting in only a small iodine loss (< 1wt%) at ~350°C. No method of curtailing loss of sulfur containing compounds due to heating was successful in this scoping study.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Thermal Test on Target with Pressed Disks

A thorough test of the thermal performance of a target for Mo 99 production using solid Mo 100 target to produce the Mo 99 via a gamma-n reaction has previously been conducted at Argonne National Laboratory (ANL). The results are reported in “Zero Degree Line Mo Target Thermal Test Results and Analysis,” LANL report Number LA-UR-15-23134 dated 3/27/15. This target was comprised of 25 disks 1 mm thick and 12 mm in diameter, separated by helium coolant gaps 0.5 mm wide. The test reported in the above referenced report was conducted with natural Mo disks all cut from commercial rod. The production plant will have Mo 100 disks pressed and sintered using a process being developed at Oak Ridge National Laboratory (ORNL). The structural integrity of press-and-sinter disks is of some concern. The test reported herein included 4 disks made by the ORNL process and placed in the high heat, and therefore high thermal stress, region of the target. The electron beam energy was 23 MeV for these tests. Beam spot size was 3.5 mm horizontal and 3 mm vertical, FWHM. The thermal stress test of pressed-and-sintered disks resulted in no mechanical failures. The induced thermal stresses were below yield stress for natural Mo, indicating that up to that stress state no inherent deficiencies in the mechanical properties of the fabricated disks were evident.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2019

Radiation Effects on High Thermal Conductivity Fuels (Final Scientific Report)

High thermal conductivity nuclear fuels offer important potential advantages over traditional oxide-based fuels such as higher burnup, reduction in fission gas release, and better overall safety of the reactor system. One interesting approach to high thermal conductivity fuels utilizes high thermal conductivity nonfissile additives to UO 2 fuel to lower the fuel operating temperature and thereby take advantage of the highly favorable radiation resistance of UO 2 at lower operating temperatures. However, differential swelling between the matrix and high conductivity additive phases during high dose irradiation could lead to internal cracking and poor performance. In the current study, ceria (CeO 2 ) and zirconia (ZrO 2 ) surrogate matrices were used to model UO 2 behavior. Al 2 O 3 or SiC in the form of nanoscale powder or platelets, respectively, were used for the high conductivity second phase. The nuclear fuel surrogates were sintered to achieve densities greater than 93% of the ideal values. Scanning electron microscopy (SEM) imaging and X-ray diffraction confirmed the uniform distribution of the second phase and that no intermetallic second phase was formed during sintering. The thermal conductivity of the sintered samples was measured from 50°C to 900°C and revealed an important increase compared to pure CeO2 and ZrO2 pellets. Samples were irradiated with 20 MeV Ni6+ ions at midrange doses ranging from 1 to 15 displacements per atom (dpa) and temperatures from 300°C to 700°C. Post irradiation characterization revealed a good stability of the samples at low to medium doses (1 to 5 dpa) but showed a significant microstructural deterioration and decrease of the mechanical properties at 15 dpa. Although microcracking is not observed at the interface between the matrix and high conductivity phase for any investigated irradiation condition, the strength degradation at 15 dpa suggests that these high thermal conductivity fuel forms may not be suitable for high burnup applications in current or proposed fission reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Manufacturing of Advanced Alnico Magnets for Energy Efficient Traction Drive Motors CRADA Final Report

The primary theme of this Technology Commercialization Fund (TCF) project was refining the pre-alloyed powder processing approach (with alnico 8, modified for higher coercivity) of that came out of the previous Development of Radically Enhanced alnico Magnets (DREaM) project to permit full size net-shape alnico magnets to be produced in a reproducible manner that could allow testing in an advanced Permanent Magnet (PM) drive motor. Previously, a lack of sufficient coercivity in alnico magnets limits their energy product and their application in automotive traction drive motors, despite their high temperature stability. Use of enhanced sintered alnico magnets, instead of rare earth (RE) magnets or larger cast alnico magnets, could lower costs and decrease cooling needs of these motors. Conventional production of the best (aligned) alnico magnets (alnico 9) involves costly directional solidification (DS) and achieves good alignment, but modest energy product (10 MGOe), because of low coercivity. Other limitations of cast alnico 9 magnets are poor mechanical properties and difficulty in scaling special casting molds to mass production. In spite of these problems with alnico 9, a commercial electric motor company, UQM, developed a fully capable traction drive motor that met many 2022 DOE-VTO performance targets, except full speed operation, due to brittle mechanical behavior. While UQM demonstrated an advanced drive motor that used alnico 9, they also encouraged the development of improved alnico, especially for greater coercivity (seeking 2X) and improved mechanical properties. While commercial sintered alnico magnets are less brittle and have improved coercivity, they have an inferior energy product due to their non-aligned, fine-grained microstructure. Thus, full development and up-scaling of well-aligned alnico magnets with a further increase in coercivity and good mechanical properties by a low cost powder processing route became the theme of this TCF project. The processing route for this project involved high-pressure gas atomization, at Ames and Carpenter, of modified alnico 8 compositions, compression molding of the resulting pre-alloyed powders into bulk samples, de-binding and sintering the samples to full density, and a final magneto-thermal treatment of the resulting bulk magnets, at Ames and Arnold Magnetic Technologies, to produce aligned magnets, which were intended for motor testing at UQM and Ford.

42 ENGINEERING↗
DOE OSTI2020

Doping effect of Al in LLZO

Lithium ion batteries have become a common use in most electronic devices and transportation. However, the use of liquid electrolytes poses a serious safe hazard due to their high flammability. The narrow operating temperature and voltage windows also limit further improvement of the energy density.Solid-state lithium batteries with the use of more stable and safer solid electrolyte have garnered much attention and could be the future choice for battery technology. A promising potential candidate for the solid electrolyte component is the garnet type Li 7 La 3 Zr 2 O 12 (LLZO) ceramic material since it possesses high ionic conductivity at room temperature and enables the use of high capacity lithium anode and high voltage/capacity cathodes.However, to form the stable cubic phase of LLZO and high densification,high sintering temperatures above 1100°C is typically required, which causes Lithium loss of the system.Many studieshave been taken to dop LLZO with various precursors such as Ga, Ta, and Al to stabilize the cubic structure and reduce calcination temperature, while the doping effect on sintering densification is still unclear. In this study Al doping along with ball milling were explored to stabilize the cubic phase of LLZO and improve densification, while reducing the amount of impurity phases. Samples were synthesized from the precursors Li 2 CO 3 , Al 2 O 3 , La 2 O 3 , and ZrO 2 by ball milling followed by heat treatment for 12 hours at 1000°C. XRD with Rietveld fitting was used to determine the two phases of LLZO (cubic, tetragonal) and other possible secondary phases. Furthermore,SEM with top and cross sectional views was conducted to investigate the morphology and microstructure of sintered pellets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of 18 O Exchange on Neutron Emission Rates of Aging 238 PuO 2 LWRHUs

The Lightweight Radioisotope Heater Unit (LWRHU) provides about 1 Watt of thermal power to critical electrical and mechanical systems in the extreme temperatures of space, maintaining the operating temperature of the spacecraft’s scientific and general operating equipment. Los Alamos National Laboratory (LANL) designed and tested the LWRHU in the 1970s through early 1980s. The first production campaign at LANL was in the early 1980s in support of the Galileo mission in which over 100 LWRHUs were manufactured. In the mid-1990s, almost 200 LWRHUs were manufactured in support of the Cassini mission. After the primary Cassini manufacturing campaign, the Department of Energy (DOE) approved the fabrication of more than 10 additional LWRHUs as spares in 1998. The LWRHU assembly contains the following components: a fuel pellet, a vented capsule, a pyrolytic graphite insulator, and a fine-weave pierced fabric (FWPF) graphite aeroshell. The fuel pellet is a hot-pressed 238 PuO 2 cylindrical pellet that is sintered to create a ceramic pellet. The pellet is encapsulated in a platinum-rhodium encapsulation. The welded fueled clad is placed inside a pyrolytic graphite thermal insulation to protect the fuel from the heat produced in reentry events. The exterior layer of the LWRHU assembly is the FWPF aeroshell. Before sintering, PuO 2 granules are heated in a furnace at temperatures greater than or equal to 700°C under an enriched 16 O atmosphere in order to reduce trace quantities of 18 O. Because 18 O undergoes an (α,n) reaction, 18 O needs to be removed as much as possible to meet radiation emission requirements set by the Jet Propulsion Laboratory (JPL) and the National Aeronautics and Space Administration (NASA), as well as other agencies. The relative abundances of the oxygen isotopes are indicated by neutron emission rate (NER) measurements. LWRHUs are vented with a sintered platinum frit vent (George 1986). During extraterrestrial operation, the vent in the cladding allows helium from the decay of plutonium to escape and relieves pressure from the system while preventing the solids from escaping (Rinehart 1996, Tate 1982 & 1985). This vent is protected during manufacture by a platinum-30 rhodium cover. The capsule vent is activated by milling a 0.025-inch diameter hole through the protective cover to a nominal depth of 0.015 inches, generally immediately before the LWRHU is loaded into the aeroshell (George 1986). Prior to long-term storage, LWRHUs are vented and thus potentially allow infiltration of 18 O from the ambient atmosphere. Although NER decreases with age due to the reduction in emitted alpha particles, it might be expected that NER reduction is mitigated by the exchange of 18 O. However, this is not necessarily the case and no trend was observed relating NER to age other than the natural decay of 238 Pu (Mulford 2021). The most probable and dominant factor for determining specific NER was manufacturing discrepancies between individual units. It is important to understand the lack of observed 16 O- 18 O exchange and to compare LWRHU pellets as much as possible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Compositional Exploration of Additively Manufactured Ultra-High-Temperature Ceramic Composites for Use in Concentrated Solar Power Plant Heat Exchangers

The DOE has research interest in new technologies for high temperature concentrated solar power plants. Our project this summer was to explore the use of additively manufactured ultra-high-temperature ceramics in a heat exchanger. The heat exchanger would transfer heat between a molten chloride salt and supercritical CO 2 . We selected 22 compositions to test and were able to mix 14 of these compositions. We sintered these compositions using pressureless sintering and direct current sintering. We also conducted high temperature TGA on some ceramic samples. We also performed preliminary binder jet additive manufacturing trials with tungsten carbide powder. Our work so far points towards one of our titanium diboride samples being promising, but much more research needs to be done.

14 SOLAR ENERGY↗
DOE OSTI2022

Status of Additive Manufacturing Capabilities for Processing Refractory Alloys Under the Mo-99 Program

The enriched 100 Mo target, denoted as aMo, that Northstar Medical Radioisotopes is developing to produce 99 Mo from an accelerator-based method is a disk-type geometry with a 0.5–0.715 mm thickness and a 29 mm outer diameter. A press and sinter method was adopted to fabricate these samples from aMo powder feedstock. Inherent porosity from the press and sinter method makes the disks more easily dissolvable during 99 Mo postprocessing. However, the disk-type geometry will be subject to thermal stresses due to temperature variations once the geometry is in line with the accelerated electron beam, causing warping and possible failure. Additive manufacturing (AM) processes such as laser powder bed fusion (LPBF) enable the manufacturing of custom, complex geometries that may otherwise be difficult to produce with more conventional methods (e.g., press and sinter approach). Therefore, the National Nuclear Security Administration’s Molybdenum-99 Program invested in developing an AM facility dedicated to processing and printing refractory powders. This report details the LPBF process, how irregular refractory powder can be prepared for LPBF, and the equipment that is available to support the program.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Small Punch Testing of Molybdenum-99 Targets

Northstar Medical Radioisotopes is developing an accelerator-based method to produce 99 Mo, which is a parent isotope of the commonly used 99m Tc medical isotope. The Mo targets being designed for the accelerator will be produced from enriched 100 Mo, also known as aMo . Pressed and sintered powder feedstock is used to fabricate aMo targets, producing 29 mm disk-shaped targets. The targets are subjected to 1–6 days in line of an electron beam with subsequent dissolution of the disk to retain the 99 Mo, which decays to 99m Tc at radio-pharmacies. The press and sinter method is advantageous because the inherent porosity produced by this method enables increased surface area and therefore increased flow of dissolution media, decreasing the dissolution time and reducing the need for a highly acidic media. Although porosity aids in dissolution, it reduces the mechanical strength and ductility. Targets require good mechanical integrity when subjected to the conditions in the accelerator. Therefore, Northstar is seeking methods to rapidly test disk samples after fabrication to assure mechanical performance metrics are achieved. This report details the design and testing of a small punch test (SPT) that accommodates the 29 mm disk. Initial data were used to relate the SPT data to tensile properties, such as the yield strength (YS), ultimate tensile strength (UTS), and total elongation to failure. Although the SPT has been established as a somewhat reliable method for testing metallic materials, few studies have applied the SPT to refractory materials such as Mo. Based on tensile testing performed at Oak Ridge National Laboratory on different Mo samples, correlation between the Mo tensile and SPT properties could be performed, establishing a standard calibration that could be applied to other Mo samples. To test the efficacy of the SPT with Mo, multiple different disk batches were fabricated under different conditions (e.g., pressure, lubricant) with commercially available pure Mo powder. Generally, only a UTS could be well defined because the press and sinter disks failed under brittle fracture, making it difficult to determine the YS and elongation. Compared with disks fabricated with aMo powder, the aMo samples underperformed their pure nat Mo counterparts. This report summarizes the current status of the SPT, but further evaluation is needed before it can be applied as a reliable quality assurance tool.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2023

Investigation of oxygen ion mobility through Zr x Ta 2 O 2x+5 (ZTOx) and Hf 6 Ta 2 O 17 (HTO) at elevated temperatures

Thermal Protection Systems (TPS) allow for technology to withstand high heat, which is especially critical for aerospace applications. As technology advances, better TPS are required to keep up with more extreme operating temperatures. Ultra-High Temperature Ceramics (UHTCs) are of interest because of their high melting points above 3000°C, but they suffer from oxidation when exposed to the atmosphere. A standard remedy to prevent oxidation is the use an oxide coating to shield from oxygen in the atmosphere while still allowing high operating temperatures and thermal cycling. However, standard oxide coatings such as yttria stabilized zirconia (YSZ) have limited operating temperatures before they allow oxygen to diffuse into the substrate material. A recently proposed alternative material has the formula A 6 B 2 O 17 (A: Zr or Hf) (B: Ta or Nb). In this study, determination of the oxygen protection ability of Hf 6 Ta 2 O 17 (HTO), Zr 6 Ta 2 O 17 (ZTO6), and various Zr x Ta 2 O 2x+5 (ZTOx) was determined using Electrochemical Impedance Spectroscopy (EIS). Optimal synthesis and sintering conditions were determined for ZTO6 and several of its ZTO variations. Activation energy for oxygen mobility was also determined. The importance of ball milling was found to be crucial to achieve high sintering density with these ceramics. The sintering study revealed that the ideal temperature of the ZTO variations increased with increased Zr/Ta ratio in the formulation. It was determined that both HTO and the ZTO variations conduct oxygen ions less than current ceramic coatings such as YSZ, with HTO conducting the least, with results confirming the validity of both HTO and ZTO materials as candidates for TPS coatings based on their low oxygen ion conductivity.

36 MATERIALS SCIENCE↗